Age | Commit message (Collapse) | Author | Files | Lines |
|
Now that kernel-doc can hanle nested structs/unions, describe
such fields at w1_netlink_message_types.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
The w1 master driver includes a complete open drain emulation
reimplementation among other things.
This converts the driver and all board files using it to use
GPIO descriptors associated with the device to look up the
GPIO wire, as well ass the optional pull-up GPIO line.
When probed from the device tree, the driver will just pick
descriptors and use them right off. For the two board files
in the kernel, we add descriptor lookups so we do not need
to keep any old platform data handling around for the GPIO
lines.
As the platform data is also a state container for this driver,
we augment it to contain the GPIO descriptors.
w1_gpio_write_bit_dir() and w1_gpio_write_bit_val() are gone
since this pair was a reimplementation of open drain emulation
which is now handled by gpiolib.
The special "linux,open-drain" flag is a bit of mishap here:
it has the same semantic as the same flags in I2C: it means
that something in the platform is setting up the line as
open drain behind our back. We handle this the same way as
in I2C.
To drive the pull-up, we need to bypass open drain emulation
in gpiolib for the line, and this is done by driving it high
using gpiod_set_raw_value() which has been augmented to have
the semantic of overriding the open drain emulation.
We also augment the documentation to reflect the way to pass
GPIO descriptors from the machine.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
|
|
w1_therm_eeprom() and w1_DS18B20_precision() decrement THERM_REFCNT
on error paths, while they did not increment it yet.
read_therm() unlocks bus mutex on some error paths,
while it is not acquired.
The patch makes sure all the functions keep the balance in usage of
the mutex and the THERM_REFCNT.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This subpatch adds a driver for the DS28E17 Onewire to I2C master bridge.
Signed-off-by: Jan Kandziora <jjj@gmx.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The w1_ds28e17 driver from the next part of this patch needs to emit
single-bit read timeslots to the DS28E17. The w1 subsystem already
has this function but it is not exported outside drivers/w1/w1_io.c
This subpatch exports the w1_touch_bit symbol with EXPORT_SYMBOL_GPL,
same as the other exported symbols in drivers/w1/w1_io.c
May be also useful later for writing drivers for other Onewire chips
which do single-bit communication.
Signed-off-by: Jan Kandziora <jjj@gmx.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset changes from Sebastian Reichel:
"New chip/feature support:
- bq27xxx: support updating battery config from DT
- bq24190: support loading battery charge info from DT
- LTC2941: add LTC2942/LTC2944 support
- max17042: add ACPI support
- max1721x: new driver
Misc:
- Move bq27xxx w1 driver from w1 into power-supply subsystem
- Introduce power_supply_set_input_current_limit_from_supplier
- constify stuff
- some minor fixes"
* tag 'for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (39 commits)
power: supply: bq27xxx: enable writing capacity values for bq27421
power: supply: bq24190_charger: Get input_current_limit from our supplier
power: supply: bq24190_charger: Export 5V boost converter as regulator
power: supply: bq24190_charger: Add power_supply_battery_info support
power: supply: bq24190_charger: Add property system-minimum-microvolt
power: supply: bq24190_charger: Enable devicetree config
dt-bindings: power: supply: Add docs for TI BQ24190 battery charger
power: supply: bq27xxx: Remove duplicate chip data arrays
power: supply: bq27xxx: Enable data memory update for certain chips
power: supply: bq27xxx: Add chip IDs for previously shadowed chips
power: supply: bq27xxx: Create single chip data table
power: supply: bq24190_charger: Add ti,bq24192i to devicetree table
power: supply: bq24190_charger: Add input_current_limit property
power: supply: Add power_supply_set_input_current_limit_from_supplier helper
power: supply: max17042_battery: Fix compiler warning
power: supply: core: Delete two error messages for a failed memory allocation in power_supply_check_supplies()
power: supply: make device_attribute const
power: supply: max17042_battery: Fix ACPI interrupt issues
power: supply: max17042_battery: Add support for ACPI enumeration
power: supply: lp8788: Make several arrays static const * const
...
|
|
This change adds hwmon temp support for w1_therm.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
separate
Inside the w1_slave_show function refactor the code to read the temp
into a separate function.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch has changes to w1.h/w1.c generic files to add (optional) hwmon
support structures.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a one wire driver for the DS28E05 one wire slave chip. This chip
requires OverDrive support to talk to it.
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PPM/SPU/1WS features
Extend the one wire DS2482 master driver with a module option that allows support
for PPM/SPU/1WS interface modes to be requested. This allows support of chips
that require one or more of these features such as the DS28E05.
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The functions w1_ds2438_get_page, w1_ds2438_get_temperature,
w1_ds2438_change_config_bit and w1_ds2438_get_voltage are local to
the source and do not need to be in global scope, so make it static.
Cleans up sparse warnings:
symbol 'w1_ds2438_get_page' was not declared. Should it be static?
symbol 'w1_ds2438_get_temperature' was not declared. Should it be static?
symbol 'w1_ds2438_change_config_bit' was not declared. Should it be static?
symbol 'w1_ds2438_get_voltage' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
w1: ds1wm: add messages to make incorporation in mfd-drivers easier
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
w1: ds1wm: silence interrupts on HW before claiming the interrupt.
This way avoid possible invalid interrupts in the initialization phase.
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
w1: ds1wm: add level interrupt modes
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
o Make endian clean, make HW-endianness configurable.
o Use ioread*, iowrite* instead of __raw_readb,__raw_writeb
to also use memory-barriers when accessing HW-registers.
We do not want reordering to happen here.
Both changes are tightly coupled, so I do them in one patch
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace incorrect register offsett calculation by
direct configuration of bus_shift in mfd-cell.
Indirect definition of address-shift by resource size
was unobvious and was wrong (should have used a binary log).
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The HDQ interface driver should be in this folder just like the I2C
interface driver. Move this driver out of drivers/w1/slave and into
drivers/power/supply.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
platform_get_irq() returns an error code, but the omap_hdq
driver ignores it and always returns -ENXIO. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error.
Print error message and propagate the return value of
platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
1-Wire bus have very fast algorith for exchange with single slave
device. Fix incorrect count of slave devices on connect second slave
device. This case on slave device probe() step we need use generic
(multislave) functions for read/write device.
Signed-off-by: Alex A. Mihaylov <minimumlaw@rambler.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Like other subsystems we should be able to define slave devices outside
of the w1 directory. To do this we move public facing interface
definitions to include/linux/w1.h and rename the internal definition
file to w1_internal.h.
As w1_family.h and w1_int.h contained almost entirely public
driver interface definitions we simply removed these files and
moved the remaining definitions into w1_internal.h.
With this we can now start to move slave devices out of w1/slaves and
into the subsystem based on the function they implement, again like
other drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Structures and functions should be ordered such that forward declaration
use is minimized.
MODULE_* macros should immediately follow the structures and functions
upon which they act.
Remaining MODULE_* macros should be at the end of the file in
alphabetical order.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The only use of assert() is in matrox_w1.c and is used to check the input
to probe() from the PCI subsystem for NULL values, these are guaranteed
to be populated and no other PCI driver makes this check, remove this.
As this was the only definition in w1_log.h, remove this also.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Detailed information about support and provided sysfs files
in my next commit which creates a documentation file:
Documentation/w1/slaves/w1_ds2438
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
<linux/sched/signal.h>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
module_w1_family() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use kmemdup rather than duplicating its implementation.
Generated by: scripts/coccinelle/api/memdup.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove filename from file, this is not done anymore as it doesn't
add anything and usually is incorrect as filename change often.
Also shorten the GPL to the more common address-less version and
remove excess white-space.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Near the beginning of w1_attach_slave_device() we increment a w1 master
reference count.
Later, when we are going to exit this function without actually attaching
a slave device (due to failure of __w1_attach_slave_device()) we need to
decrement this reference count back.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: stable@vger.kernel.org
Fixes: 9fcbbac5ded489 ("w1: process w1 netlink commands in w1_process thread")
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds a driver for a DS2405 1-wire single-channel addressable switch.
The DS2405 can also work as a single-channel binary remote sensor.
This driver supports two attributes: "state" and "output" which are the
same attribute names as supported by existing DS2406, DS2408 and DS2413
drivers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ds2490 driver was doing USB transfers from / to buffers on a stack.
This is not permitted and made the driver non-working with vmapped stacks.
Since all these transfers are done under the same bus_mutex lock we can
simply use shared buffers in a device private structure for two most common
of them.
While we are at it, let's also fix a comparison between int and size_t in
ds9490r_search() which made the driver spin in this function if state
register get requests were failing.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of error returned by '_omap_hdq_reset()', free resources as done
elsewhere in this function.
This patch slighly changes the semantic of the code. It now propagates the
error code returned by '_omap_hdq_reset()' instead of returning -EINVAL
unconditionally.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix 'timeout_us' parameter description.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Correct pointer notations to include whitespace between
variable type and "*" character. Inserted blank line
after variable declatations at two locations.
Rearranged comparison within an if statment to have the
constant on the right-hand side.
Signed-off-by: Ben Werbowyj <ben.werbowyj@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Assignment of variable count removed from within an if statment.
This was done at two locations in the file.
Signed-off-by: Ben Werbowyj <ben.werbowyj@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Inserted whitespace between command and open parenthesis
at two locations. Removed new line between open brace and
command/declaration at two locations.
Signed-off-by: Ben Werbowyj <ben.werbowyj@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e93762bbf681 ("w1: masters: omap_hdq: add support for 1-wire
mode") added a statement to clear the hdq_irqstatus flags in
hdq_read_byte().
If the hdq reading process is scheduled slowly or interrupts are
disabled for a while the hardware read activity might already be
finished on entry of hdq_read_byte(). And hdq_isr() already has set the
hdq_irqstatus to 0x6 (can be seen in debug mode) denoting that both, the
TXCOMPLETE and RXCOMPLETE interrupts occurred in parallel.
This means there is no need to wait and the hdq_read_byte() can just
read the byte from the hdq controller.
By resetting hdq_irqstatus to 0 the read process is forced to be always
waiting again (because the if statement always succeeds) but the
hardware will not issue another RXCOMPLETE interrupt. This results in a
false timeout.
After such a situation the hdq bus hangs.
Link: http://lkml.kernel.org/r/b724765f87ad276a69625bc19806c8c8844c4590.1469513669.git.hns@goldelico.com
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The helper macro module_w1_family can be used in module drivers that
only register a w1 driver in their module init functions. Add this
macro and use it in all applicable drivers.
Link: http://lkml.kernel.org/r/20160531204313.20979-2-afd@ti.com
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PLATFORM_DEVID_AUTO can be used to have the platform core assign a
unique ID instead of manually creating one with IDA. Do this in all
applicable drivers.
Link: http://lkml.kernel.org/r/20160531204313.20979-1-afd@ti.com
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sensors like DS18B20
Since many temperature sensors come "preconfigured" with a lower
precision, people are stuck at that precision when running on a kernel
based device (unlike the Dallas 1Wire library for e.g. Arduino, which
supports writing the configuration/scratchpad). This patch adds write
support for the scratchpad/precision registers via w1_slave sysfs.
Signed-off-by: Ben Sen <0.x29a.0@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If kstrtoint() returns -ERANGE then "tmp" is uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polaykov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit enables the active pullup (APU bit) by default for
the DS2482 1-Wire master.
>From the DS2482 datasheet:
"The APU bit controls whether an active pullup (controlled slew-rate
transistor) or a passive pullup (Rwpu resistor) will be used to drive
a 1-Wire line from low to high. When APU = 0, active pullup is disabled
(resistor mode). Active Pullup should always be selected unless there is
only a single slave on the 1-Wire line."
According to the module author, Ben Gardner:
"It doesn't look like active pullup would cause any hurt if there
is only a single slave."
And my tests with multiple and single slaves on 1-Wire bus
confirms that.
This active pullup can be manually disabled using the introduced
module parameter:
active_pullup = 0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
w1_process() calls try_to_freeze(), but the thread doesn't mark itself
freezable through set_freezable(), so the try_to_freeze() call is useless.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|