| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Unconditionally wake up the child device when the power session is
recovered.
This addresses the following scenarios:
1/ The device may need a reset on power-session loss, without this
change port power-on recovery exposes khubd to scenarios that
usb_port_resume() is set to handle. Prior to port power control the
only time a power session would be lost is during dpm_suspend of the
hub. In that scenario usb_port_resume() is guaranteed to be called
prior to khubd running for that port. With this change we wakeup the
child device as soon as possible (prior to khubd running again for this
port).
Although khubd has facilities to wake a child device it will only do
so if the portstatus / portchange indicates a suspend state. In the
case of port power control we are not coming from a hub-port-suspend
state. This implementation simply uses pm_request_resume() to wake the
device and relies on the port_dev->status_lock to prevent any collisions
between khubd and usb_port_resume().
2/ This mechanism rate limits port power toggling. The minimum port
power on/off period is now gated by the child device suspend/resume
latency. Empirically this mitigates devices downgrading their connection
on perceived instability of the host connection. This ratelimiting is
really only relevant to port power control testing, but it is a nice
side effect of closing the above race. Namely, the race of khubd for
the given port running while a usb_port_resume() event is pending.
3/ Going forward we are finding that power-session recovery requires
warm-resets (http://marc.info/?t=138659232900003&r=1&w=2). This
mechanism allows for warm-resets to be requested at the same point in
the resume path for hub dpm_suspend power session losses, or port
rpm_suspend power session losses.
4/ If the device *was* disconnected the only time we'll know for sure is
after a failed resume, so it's necessary for usb_port_runtime_resume()
to expedite a usb_port_resume() to clean up the removed device. The
reasoning for this is "least surprise" for the user. Turning on a port
means that hotplug detection is again enabled for the port, it is
surprising that devices that were removed while the port was off are not
disconnected until they are attempted to be used. As a user "why would
I try to use a device I removed from the system?"
1, 2, and 4 are not a problem in the system dpm_resume() case because,
although the power-session is lost, khubd is frozen until after device
resume. For the rpm_resume() case pm_request_resume() is used to
request re-validation of the device, and if it happens to collide with a
khubd run we rely on the port_dev->status_lock to synchronize those
operations.
Besides testing, the primary scenario where this mechanism is expected
to be triggered is when the user changes the port power policy
(control/pm_qos_no_poweroff, or power/control). Each time power is
enabled want to revalidate the child device, where the revalidation is
handled by usb_port_resume().
Given that this arranges for port_dev->child to be de-referenced in
usb_port_runtime_resume() we need to make sure not to collide with
usb_disconnect() that frees the usb_device. To this end we hold the
port active with the "child_usage" reference across the disconnect
event. Subsequently, the need to access hub->child_usage_bits lead to
the creation of hub_disconnect_children() to remove any ambiguity of
which "hub" is being acted on in usb_disconnect() (prompted-by sharp
eyes from Alan).
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Per Alan:
"You mean from within hub_handle_remote_wakeup()? That routine will
never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd
never sees wakeup requests if they arise during system suspend.
In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME"
portion of hub.c, along with the other suspend/resume code."
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In general we do not want khubd to act on port status changes that are
the result of in progress resets or USB runtime PM operations.
Specifically port power control testing has been able to trigger an
unintended disconnect in hub_port_connect_change(), paraphrasing:
if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
udev->state != USB_STATE_NOTATTACHED) {
if (portstatus & USB_PORT_STAT_ENABLE) {
/* Nothing to do */
} else if (udev->state == USB_STATE_SUSPENDED &&
udev->persist_enabled) {
...
} else {
/* Don't resuscitate */;
}
}
...by falling to the "Don't resuscitate" path or missing
USB_PORT_STAT_CONNECTION because usb_port_resume() was in the middle of
modifying the port status.
So, we want a new lock to hold off khubd for a given port while the
child device is being suspended, resumed, or reset. The lock ordering
rules are now usb_lock_device() => usb_lock_port(). This is mandated by
the device core which may hold the device_lock on the usb_device before
invoking usb_port_{suspend|resume} which in turn take the status_lock on
the usb_port. We attempt to hold the status_lock for the duration of a
port_event() run, and drop/re-acquire it when needing to take the
device_lock. The lock is also dropped/re-acquired during
hub_port_reconnect().
This patch also deletes hub->busy_bits as all use cases are now covered
by port PM runtime synchronization or the port->status_lock and it
pushes down usb_device_lock() into usb_remote_wakeup().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a port is powered-off, or in the process of being powered-off, prevent
khubd from operating on it. Otherwise, the following sequence of events
leading to an unintended disconnect may occur:
Events:
(0) <set pm_qos_no_poweroff to '0' for port1>
(1) hub 2-2:1.0: hub_resume
(2) hub 2-2:1.0: port 1: status 0301 change 0000
(3) hub 2-2:1.0: state 7 ports 4 chg 0002 evt 0000
(4) hub 2-2:1.0: port 1, power off status 0000, change 0000, 12 Mb/s
(5) usb 2-2.1: USB disconnect, device number 5
Description:
(1) hub is resumed before sending a ClearPortFeature request
(2) hub_activate() notices the port is connected and sets
hub->change_bits for the port
(3) hub_events() starts, but at the same time the port suspends
(4) hub_connect_change() sees the disabled port and triggers disconnect
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for synchronizing port handling with pm_runtime
transitions refactor port handling into its own subroutine.
We expect that clearing some status flags will be required regardless of
the port state, so handle those first and group all non-trivial actions
at the bottom of the routine.
This also splits off the bottom half of hub_port_connect_change() into
hub_port_reconnect() in prepartion for introducing a port->status_lock.
hub_port_reconnect() will expect the port lock to not be held while
hub_port_connect_change() expects to enter with it held.
Other cleanups include:
1/ reflowing to 80 columns
2/ replacing redundant usages of 'hub->hdev' with 'hdev'
3/ consolidate clearing of ->change_bits() in hub_port_connect_change
4/ consolidate calls to usb_reset_device
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port pm_runtime implementation unconditionally clears FEAT_C_ENABLE
after clearing PORT_POWER, but the bit is reserved on usb3 hub ports.
We expect khubd to be prevented from running because the port state is
not RPM_ACTIVE, so we need to clear any errors for usb2 ports.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Three reasons:
1/ It's an invalid operation on usb3 ports
2/ There's no guarantee of when / if a usb2 port has entered an error
state relative to PORT_POWER request
3/ The port is active / powered at this point, so khubd will clear it as
a matter of course
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ClearPortFeature(PORT_POWER) on a usb3 port places the port in either a
DSPORT.Powered-off-detect / DSPORT.Powered-off-reset loop, or the
DSPORT.Powered-off state. There is no way to ensure that RX
terminations will persist in this state, so it is possible a device will
degrade to its usb2 connection. Prevent this by blocking power-off of a
usb3 port while its usb2 peer is active, and powering on a usb3 port
before its usb2 peer.
By default the latency between peer power-on events is 0. In order for
the device to not see usb2 active while usb3 is still powering up inject
the hub recommended power_on_good delay. In support of satisfying the
power_on_good delay outside of hub_power_on() refactor the places where
the delay is consumed to call a new hub_power_on_good_delay() helper.
Finally, because this introduces several new checks for whether a port
is_superspeed, cache that disctinction at port creation so that we don't
need to keep looking up the parent hub device.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[alan]: add a 'superspeed' flag to the port
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want to manipulate ->did_runtime_put in usb_port_runtime_resume(),
but we don't want that to collide with other updates. Move usb_port
flags to new port-bitmap fields in usb_hub. "did_runtime_put" is renamed
"child_usage_bits" to reflect that it is strictly standing in for the
fact that usb_devices are not the device_model children of their parent
port.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb topology after this change will have symlinks between usb3 ports
and their usb2 peers, for example:
usb2/2-1/2-1:1.0/2-1-port1/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port1
usb2/2-1/2-1:1.0/2-1-port2/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port2
usb2/2-1/2-1:1.0/2-1-port3/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port3
usb2/2-1/2-1:1.0/2-1-port4/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port4
usb2/2-0:1.0/usb2-port1/peer => ../../../usb3/3-0:1.0/usb3-port1
usb2/2-0:1.0/usb2-port2/peer => ../../../usb3/3-0:1.0/usb3-port2
usb2/2-0:1.0/usb2-port3/peer => ../../../usb3/3-0:1.0/usb3-port3
usb2/2-0:1.0/usb2-port4/peer => ../../../usb3/3-0:1.0/usb3-port4
usb3/3-1/3-1:1.0/usb3-1-port1/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port1
usb3/3-1/3-1:1.0/usb3-1-port2/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port2
usb3/3-1/3-1:1.0/usb3-1-port3/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port3
usb3/3-1/3-1:1.0/usb3-1-port4/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port4
usb3/3-0:1.0/usb3-port1/peer => ../../../usb2/2-0:1.0/usb2-port1
usb3/3-0:1.0/usb3-port2/peer => ../../../usb2/2-0:1.0/usb2-port2
usb3/3-0:1.0/usb3-port3/peer => ../../../usb2/2-0:1.0/usb2-port3
usb3/3-0:1.0/usb3-port4/peer => ../../../usb2/2-0:1.0/usb2-port4
Introduce link_peers_report() to notify on all link_peers() failure
cases.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ACPI identifies peer ports by setting their 'group_token' and
'group_position' _PLD data to the same value. If a platform has tier
mismatch [1] , ACPI can override the default (USB3 defined) peer port
association for internal hubs. External hubs follow the default peer
association scheme.
Location data is cached as an opaque cookie in usb_port_location data.
Note that we only consider the group_token and group_position attributes
from the _PLD data as ACPI specifies that group_token is a unique
identifier.
When we find port location data for a port then we assume that the
firmware will also describe its peer port. This allows the
implementation to only ever set the peer once. This leads to a question
about what happens when a pm runtime event occurs while the peer
associations are still resolving. Since we only ever set the peer
information once, a USB3 port needs to be prevented from suspending
while its ->peer pointer is NULL (implemented in a subsequent patch).
There is always the possibility that firmware mis-identifies the ports,
but there is not much the kernel can do in that case.
[1]: xhci 1.1 appendix D figure 131
[2]: acpi 5 section 6.1.8
[alan]: don't do default peering when acpi data present
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Given that root hub port peers are already established, external hub peer
ports can be determined by traversing the device topology:
1/ ascend to the parent hub and find the upstream port_dev
2/ walk ->peer to find the peer port
3/ descend to the peer hub via ->child
4/ find the port with the matching port id
Note that this assumes the port labeling scheme required by the
specification [1].
[1]: usb3 3.1 section 10.3.3
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Assume that the peer of a superspeed port is the port with the same id
on the shared_hcd root hub. This identification scheme is required of
external hubs by the USB3 spec [1]. However, for root hubs, tier mismatch
may be in effect [2]. Tier mismatch can only be enumerated via platform
firmware. For now, simply perform the nominal association.
A new lock 'usb_port_peer_mutex' is introduced to synchronize port
device add/remove with peer lookups. It protects peering against
changes to hcd->shared_hcd, hcd->self.root_hub, hdev->maxchild, and
port_dev->child pointers.
[1]: usb 3.1 section 10.3.3
[2]: xhci 1.1 appendix D
Cc: Alan Stern <stern@rowland.harvard.edu>
[alan: usb_port_peer_mutex locking scheme]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Once usb-acpi has set the port's connect type the usb_device's
->removable attribute can be set in the standard location
set_usb_port_removable().
This also changes behavior in the case where the firmware says that the
port connect type is unknown. In that case just use the default setting
determined from the hub descriptor.
Note, we no longer pass udev->portnum to acpi_find_child_device() in the
root hub case since:
1/ the usb-core sets this to zero
2/ acpi always expects zero
...just pass zero.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current port name "portX" is ambiguous. Before adding more port
messages rename ports to "<hub-device-name>-portX"
This is an ABI change, but the suspicion is that it will go unnoticed as
the port power control implementation has been broken since its
introduction. If however, someone was relying on the old name we can
add sysfs links from the old name to the new name.
Additionally, it unifies/simplifies port dev_printk messages and modifies
instances of:
dev_XXX(hub->intfdev, ..."port %d"...
dev_XXX(&hdev->dev, ..."port%d"...
into:
dev_XXX(&port_dev->dev, ...
Now that the names are unique usb_port devices it would be nice if they
could be included in /sys/bus/usb. However, it turns out that this
breaks 'lsusb -t'. For now, create a dummy port driver so that print
messages are prefixed "usb 1-1-port3" rather than the
subsystem-ambiguous " 1-1-port3".
Finally, it corrects an odd usage of sscanf("port%d") in usb-acpi.c.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A hub indicates whether it supports per-port power control via the
wHubCharacteristics field in its descriptor. If it is not supported
a hub will still emulate ClearPortPower(PORT_POWER) requests by
stopping the link state machine. However, since this does not save
power do not bother suspending.
This also consolidates support checks into a
hub_is_port_power_switchable() helper.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB core doesn't properly handle mutual exclusion between
resetting a hub and changing the power states of the hub's ports. We
need to avoid sending port-power requests to the hub while it is being
reset, because such requests cannot succeed.
This patch fixes the problem by keeping track of when a reset is in
progress. At such times, attempts to suspend (power-off) a port will
fail immediately with -EBUSY, and calls to usb_port_runtime_resume()
will update the power_is_on flag and return immediately. When the
reset is complete, hub_activate() will automatically restore each port
to the proper power state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit fixes the following sparse warning:
drivers/usb/host/pci-quirks.c:
- 252: warning: symbol 'usb_hcd_amd_remote_wakeup_quirk' was not
declared. Should it be static?
This function is exported so the fix was to add it's declaration to the
header file.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
basically renamed the Kconfig symbol USB_GADGET_PXA25X to USB_PXA25X. It
did not rename the related macros in use at that time. Commit
c0a39151a405 ("ARM: pxa: fix inconsistent CONFIG_USB_PXA27X") did so for
all but one macro. Rename that last macro too now.
Fixes: 193ab2a60700 ("usb: gadget: allow multiple gadgets to be built")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TEST 11 unlinks the URB read request for N times. When host and gadget
both initialize pattern 1 (mod 63) data series to do IN transfer, the
host side function should check the data buffer if it is as mod 63
series, because the data packet which host receivced will follow
pattern 1. So this patch adds this checking action.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected. Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.
[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 00000000 00000000 00000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB3503 chip supports 8 values of reference clock. The value is
specified by REF_SEL[1:0] pins and INT_N line. This patch add support
for getting 'refclk' clock, enabling it and setting INT_N line according
to the value of the gathered clock. If no clock has been specified,
driver defaults to the old behaviour (assuming that clock has been
specified by REF_SEL pins from primary reference clock frequencies
table).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch creates a separate instance of the usb_address0 mutex for each USB
bus, and attaches it to the usb_bus device struct. This allows devices on
separate buses to be enumerated in parallel; saving time.
In the current code, there is a single, global instance of the usb_address0
mutex which is used for all devices on all buses. This isn't completely
necessary, as this mutex is only needed to prevent address0 collisions for
devices on the *same* bus (usb 2.0 spec, sec 4.6.1). This superfluous coverage
can cause additional delay in system resume on systems with multiple hosts
(up to several seconds depending on what devices are attached).
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch "xhci: Switch Intel Lynx Point ports to EHCI on shutdown."
commit c09ec25d3684cad74d851c0f028a495999591279 is not fully correct
It switches both Lynx Point and Lynx Point-LP ports to EHCI on shutdown.
On some Lynx Point machines it causes spurious interrupt,
which wake the system: bugzilla.kernel.org/show_bug.cgi?id=76291
On Lynx Point-LP on the contrary switching ports to EHCI seems to be
necessary to fix these spurious interrupts.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Reported-by: Wulf Richartz <wulf.richartz@gmail.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's a window during which read() would return 0 instead
of a correct error for no data yet. Reorder initialization
to fix the race.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The workqueue handler may call appledisplay_bl_get_brightness() while
user space calls appledisplay_bl_update_status(). As they share a
buffer that must not happen. Use a mutex for mutual exclusion.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
send_request_dev_dep_msg_in() use a buffer allocated on the stack.
Fix by kmalloc()ing the buffer.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Converting the header to BIT for readability. No functional
change.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for the PLX USB3380 and USB3382.
This driver is based on the driver from the manufacturer.
Since USB338X is register compatible with NET2280, I thought that it
would be better to include this hardware into net2280 driver.
Manufacturer's driver only supported the USB33X, did not follow the
Kernel Style and contain some trivial errors. This patch has tried to
address this issues.
This patch has only been tested on USB338x hardware, but the merge has
been done trying to not affect the behaviour of NET2280.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Delete unnecessary local variable whose value is always 0 and that hides
the fact that the result is always 0.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression ret;
expression e;
position p;
@@
-ret = 0;
... when != ret = e
return
- ret
+ 0
;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Either we log for all chips we set the quirk for or for
none. This patch reports it for all chips.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On the Allwinner's A31 SoC the reset line connected to the EHCI IP has to
be deasserted for the EHCI block to be usable.
Add support for an optional reset controller that will be deasserted on
power off and asserted on power on.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The OHCI controllers used in the Allwinner A31 are asserted in reset using a
global reset controller.
Add optional support for such a controller in the OHCI platform driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dependency on the isp1301 driver is not something that
should be in the main OHCI driver but rather the SoC specific
part of it.
This moves the dependency for LPC32xx into USB_OHCI_HCD_LPC32XX,
and changes the 'select ISP1301_OMAP' to a similar 'depends on'.
Since the same dependency exists for the client driver, do the
same change there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PHY setup code of the TI DaVinci DA8xx OHCI controller
uses ad-hoc register access using a pointer that is meant to
be used only by the DaVinci platform implementation and that
is intentionally not exported to loadable modules. This results
in a link error on configurations that use a modular OHCI
code on this platform.
While the proper solution for this problem would be to
implement a real PHY driver shared by ohci-da8xx and musb-da8xx,
this patch for now just works around the build error by
only allowing the ohci-da8xx code to be built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we build a kernel with PM_SUSPEND set and no PM_SLEEP,
we get a build warning in the xhci-plat driver about unused
functions.
To fix this, use "#ifdef CONFIG_PM_SLEEP", like we do in most
other drivers nowadays.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The dwc2 IP on the SOCFPGA cannot use the default HW configured
FIFO sizes. The total FIFO depth as read from GHWCFG3 reports 0x1f80 or 8064
32-bit words. But the GRXFSIZ, GNPTXFSIZ, and HPTXFSIZ register defaults
to 0x2000 or 8192 32-bit words. So the driver cannot just use the fifo sizes
as read from those registers.
For platforms that face the same issue, this commits sets the RX, periodic TX,
and non-periodic TX fifo size to those that are recommended v2.93a spec for
the DWC2 IP. Implements Method #2 from the Synopsys v2.93a spec for the DWC2.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even though the IP supports Descriptor DMA mode, it does not support SPLIT
transactions in this mode. So the driver, in its currently form, will not
support LS/FS devices when connected to a HS Hub if Descriptor DMA mode is
enabled.
So we should just default to disable descriptor dma mode.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Armada 375 and 38x SoCs come with an XHCI controller that requires
some specific initialization related to the MBus windows
configuration. This patch adds the support for this special
configuration as an XHCI quirk executed during probe.
Two new compatible strings are added to identify the Armada 375 and
Armada 38x XHCI controllers, and therefore enable the relevant quirk.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some platforms (such as the Armada 38x ones) can gate the clock of
their USB controller. This patch adds the support for one clock in
xhci-plat, by enabling it during probe and disabling it on remove.
To achieve this, it adds a 'struct clk *' member in xhci_hcd. While
only used for now in xhci-plat, it might be used by other drivers in
the future. Moreover, the xhci_hcd structure already holds other
members such as msix_count and msix_entries, which are MSI-X specific,
and therefore only used by xhci-pci.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Sorting the headers in alphabetic order will help to reduce the conflict
when adding new headers later.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit extends the ehci-orion so that it can optionally be passed
a reference to a PHY through the Device Tree. It will be useful for
the Armada 375 SoCs. If no PHY is provided then the behavior of the
driver is unchanged.
[Thomas: use devm_phy_optional_get() so that we handle -EPROBE_DEFER
properly. Also call phy_power_off() when needed, and rename goto
labels.]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to disable the clock in the ->remove() function, a call to
devm_clk_get() is being made, which further increases the reference
count of the clock.
In order to clean this up, a private structure holding a pointer to
the clock is added using the override mechanism provided by the ehci
framework. This makes the driver clock handling much more logical.
The bug was introduced in v3.6, however the ehci framework allowing to
use the override mechanism has only been introduced in v3.8, so this
patch won't apply before it.
[Thomas: reword commit log, fix goto label names.]
Fixes: 8c869edaee07c623066266827371235fb9c12e01 ('ARM: Orion: EHCI: Add support for enabling clocks')
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation to the introduction of additional initialization steps
in ehci_orion_drv_probe(), we rename the error goto labels from err1,
err2 and err3 names to some more meaningful names.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 77dae54ab385033e488d8b07045bc7f8d931740f ('ARM: Kirkwood:
ehci-orion: Add device tree binding') added the Device Tree binding
for the ehci-orion driver. To achieve that with the irq, it used the
irq_of_parse_and_map() function when probed in DT-mode, and
platform_get_irq() when probed in non-DT mode.
This is not necessary: platform_get_irq() works just as fine in
DT-mode, since the conversion from DT information to 'struct resource'
is done by the generic layers of the kernel.
Therefore, this commit switches back to use just platform_get_irq().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since usb otg fsm implementation is not related to usb phy.
We move it from usb/phy/ to usb/common/, and rename it to
reflect its real meaning.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since we will have more usb-common things, and it will let
usb-common.c be larger and larger, we create a folder named usb/common
for all usb common things.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
%pad notation automatically prints in hexadecimal format (with '0x'), so remove
the unneeded '0x' to avoid a '0x0x' string.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
