Age | Commit message (Collapse) | Author | Files | Lines |
|
TD.4.7.3. Try SNK DRP Connect Try.SRC DRP fails. The compliance
tester mimics being a Try.SRC USB-C port.
The failure is due to TCPM exiting SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS
when VBUS is not present eventhough when SNK.Rp is seen. Exit to
SRC_TRYWAIT from SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS only when SNK.Rp
is not seen for PD_T_TRY_CC_DEBOUNCE.
>From the spec:
The port shall then transition to Attached.SNK when the SNK.Rp state
is detected on exactly one of the CC1 or CC2 pins for at least
tTryCCDebounce and VBUS is detected. Alternatively, the port shall
transition to TryWait.SRC if SNK.Rp state is not detected for
tTryCCDebounce.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201125014804.1596719-1-badhri@google.com
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During PR_SWAP sequence, when TCPM is waiting in PR_SWAP_SNK_SRC_SOURCE_ON
for the vbus source to ramp up, TCPM would prematurely exit
PR_SWAP_SNK_SRC_SOURCE_ON and transition to SNK_UNATTACHED state when a
vbus off notification is received. This should not be the case as vbus
can still be off while in PR_SWAP_SNK_SRC_SOURCE_ON and the vbus source
has PD_T_NEWSRC to ramp up.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201125020703.1604979-1-badhri@google.com
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A PD-capable device can return up to 3 Product Type VDOs as part of its
DiscoverIdentity Response (USB PD Spec, Rev 3.0, Version 2.0, Section
6.4.4.3.1). Add sysfs attributes to expose these to userspace.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201125084911.1077462-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This modernized the ISP1301 a bit by switching it to provide
a GPIO descriptor from the H2 board if used.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201123102346.48284-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break/return/fallthrough
statements instead of letting the code fall through to the next
case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/a76da7ca5b4f41c13d27b298accb8222d0b04e61.1605896060.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit to introduce the num_altmodes attribute for partner had an
error where one of the parameters was named differently in the comment
and the function signature. Fix the version in the comment to align with
what is in the function signature.
This fixes the following htmldocs warning:
drivers/usb/typec/class.c:632: warning: Excess function parameter 'num_alt_modes' description in 'typec_partner_set_num_altmodes'
Fixes: a0ccdc4a77a1 ("usb: typec: Add number of altmodes partner attr")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201120063523.4159877-1-pmalani@chromium.org
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a field to the typec_plug struct to record the number of available
altmodes as well as the corresponding sysfs attribute to expose this to
userspace.
This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the plug. The sysfs file remains
hidden as long as the attribute value is -1.
We re-use the partner attribute for number_of_alternate_modes since the
usage and name is similar, and update the corresponding *_show() command
to support both partner and plugs.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-4-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Changing compatible string to include the part number.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
New smatch warnings:
drivers/usb/typec/tcpm/tcpci_maxim.c:324 max_tcpci_irq() error: uninitialized symbol 'irq_return'.
drivers/usb/typec/tcpm/tcpci_maxim.c:407 max_tcpci_probe() warn: passing zero to 'PTR_ERR'
The change fixes the above warnings by initializing irq_return
and replacing IS_ERR_OR_NULL with IS_ERR.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-11-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable auto discharge disconnect for Maxim TCPC.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-10-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vImplement callbacks for enabling/disabling
POWER_CONTROL.AutoDischargeDisconnect.
Programs VBUS_SINK_DISCONNECT_THRESHOLD based on the
voltage requested as sink, mode of operation.
The programmed threshold is based on vSinkDisconnect and
vSinkDisconnectPD values.
Add auto_discharge_disconnect to tdata to allow TCPC chip
level drivers enable AutoDischargeDisconnect.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-9-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TCPCI spec allows TCPC hardware to autonomously discharge the vbus
capacitance upon disconnect. The expectation is that the TCPM enables
AutoDischargeDisconnect while entering SNK/SRC_ATTACHED states. Hardware
then automously discharges vbus when the vbus falls below a certain
threshold i.e. VBUS_SINK_DISCONNECT_THRESHOLD.
Apart from enabling the vbus discharge circuit, AutoDischargeDisconnect
is also used a flag to move TCPCI based TCPC implementations into
Attached.Snk/Attached.Src state as mentioned in
Figure 4-15. TCPC State Diagram before a Connection of the
USB Type-C Port Controller Interface Specification.
In such TCPC implementations, setting AutoDischargeDisconnect would
prevent TCPC into entering "Connection_Invalid" state as well.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-8-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Occasionally, POWER_STATUS.sourcing_vbus takes a while to clear after
writing to MAX_BUCK_BOOST_OP register. This causes vbus to turn back
on while disconnecting the sink. Overcome this issue by writing into
MAX_BUCK_BOOST_OP during frs while sourcing vbu, instead of always
into the register whenever POWER_STATUS.sourcing_vbus is set.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-7-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-6-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-5-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
New source's current capability is now defined as string based
device tree property through new-source-frs-typec-current.
Refactor tcpm code to parse new-source-frs-typec-current and
infer local port's new source current capability during frs.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a user-visible attribute for the number of alternate modes available
in a partner. This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the partner.
Also add a sysfs file which exposes this attribute. The file remains
hidden as long as the attribute value is -1.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-3-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kfree don't need to be called after a failed kzalloc
Signed-off-by: Lucas Tanure <tanure@linux.com>
Link: https://lore.kernel.org/r/20201115102837.331335-1-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
retval may be reassigned to 0 after max3421_of_vbus_en_pin(),
if allocate memory failed after this, max3421_probe() cann't
return ENOMEM, fix this by moving assign retval afther max3421_probe().
Fixes: 721fdc83b31b ("usb: max3421: Add devicetree support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20201117061500.3454223-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Thunderbolt cable generation bits received as a part of Thunderbolt 3 cable
discover mode VDO needs to be configured for Thunderbolt rounded and
non-rounded cable support in the Thunderbolt alternate mode.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--
Changes in v2:
- No change.
--
Link: https://lore.kernel.org/r/20201113202503.6559-4-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB/Thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ehci-mxc driver was only used by i.MX non-DT platforms.
Since 5.10-rc1, i.MX has been converted to a DT-only platform and all
board files are gone.
Remove the ehci-mxc driver as there are no more users at all.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201113171231.2205-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Renesas R-Car and RZ/G SoCs have a firmware download mode over USB.
However, on reset a banner string is transmitted out which is not expected
to be echoed back and will corrupt the protocol.
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Link: https://lore.kernel.org/r/20201111131209.3977903-1-chris.brandt@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the ucsi power supply goes online/offline, and when the
power levels change, the power supply class needs to be
notified so it can inform the user space.
Fixes: 992a60ed0d5e ("usb: typec: ucsi: register with power_supply class")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Vladimir Yerilov <openmindead@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201110120547.67922-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 4b563a066611 ("ARM: imx: Remove imx21 support") the imx21
SoC is no longer supported.
Get rid of its USB driver too, which is now unused.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201109210813.21382-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When usb_stor_bulk_transfer_sglist() returns with USB_STOR_XFER_ERROR, it
returns without writing to its parameter *act_len.
Further, the two callers of usb_stor_bulk_transfer_sglist():
usb_stor_bulk_srb() and
usb_stor_bulk_transfer_sg(),
use the passed variable partial without checking the return value. Hence,
the uninitialized value of partial is then used in the further execution
of those two functions.
Clang-analyzer detects this potential control and data flow and warns:
drivers/usb/storage/transport.c:469:40:
warning: The right operand of '-' is a garbage value
[clang-analyzer-core.UndefinedBinaryOperatorResult]
scsi_set_resid(srb, scsi_bufflen(srb) - partial);
^
drivers/usb/storage/transport.c:495:15:
warning: Assigned value is garbage or undefined
[clang-analyzer-core.uninitialized.Assign]
length_left -= partial;
^
When a transfer error occurs, the *act_len value is probably ignored by the
higher layers. But it won't hurt to set it to a valid number, just in case.
For the two early-return paths in usb_stor_bulk_transfer_sglist(), the
amount of data transferred is 0. So if act_len is not NULL, set *act_len
to 0 in those paths. That makes clang-analyzer happy.
Proposal was discussed in this mail thread:
https://lore.kernel.org/linux-usb/alpine.DEB.2.21.2011112146110.13119@felia/
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201112191255.13372-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "fallthrough" pseudo-keyword was added as a portable way to denote
intentional fallthrough. Clang will still warn on cases where there is a
fallthrough to an immediate break. Add explicit breaks for those cases.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20201111014716.260633-1-ndesaulniers@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. We should decrease the usage count
whetever it succeeded or failed(maybe runtime of the device has
error, or device is in inaccessible state, or other error state).
If we do not call put operation to decrease the reference, it will
result in reference leak in xhci_histb_probe. Moreover, this
device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by jumping to error handling
branch.
Fixes: c508f41da0788 ("xhci: hisilicon: support HiSilicon STB xHCI host controller")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201106122221.2304528-1-zhangqilong3@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2d30e408a2a6b3443d3232593e3d472584a3e9f8.
On Beaglebone Black, where each interface has 2 children:
musb-dsps 47401c00.usb: can't request region for resource [mem 0x47401800-0x474019ff]
musb-hdrc musb-hdrc.1: musb_init_controller failed with status -16
musb-hdrc: probe of musb-hdrc.1 failed with error -16
musb-dsps 47401400.usb: can't request region for resource [mem 0x47401000-0x474011ff]
musb-hdrc musb-hdrc.0: musb_init_controller failed with status -16
musb-hdrc: probe of musb-hdrc.0 failed with error -16
Before, devm_ioremap_resource() was called on "dev" ("musb-hdrc.0" or
"musb-hdrc.1"), after it is called on "&pdev->dev" ("47401400.usb" or
"47401c00.usb"), leading to a duplicate region request, which fails.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 2d30e408a2a6 ("usb: musb: convert to devm_platform_ioremap_resource_byname")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201112135900.3822599-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.10-rc3
Here's a fix for a long-standing issue with the cyberjack driver and
some new device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.10-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FN980 composition 0x1055
USB: serial: option: add LE910Cx compositions 0x1203, 0x1230, 0x1231
USB: serial: cyberjack: fix write-URB completion race
USB: serial: option: add Quectel EC200T module support
|
|
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. If runtime of the device has
error or device is in inaccessible state(or other error state),
resume operation will fail. If we do not call put operation to
decrease the reference, the result is that this device cannot
enter the idle state and always stay busy or other non-idle
state.
Fixes: 249fa8217b846 ("USB: Add driver to control USB fast charge for iOS devices")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102022650.67115-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a possible issue when mtu3_gadget_stop()
already assigned NULL to mtu->gadget_driver during mtu_gadget_disconnect().
[<ffffff9008161974>] notifier_call_chain+0xa4/0x128
[<ffffff9008161fd4>] __atomic_notifier_call_chain+0x84/0x138
[<ffffff9008162ec0>] notify_die+0xb0/0x120
[<ffffff900809e340>] die+0x1f8/0x5d0
[<ffffff90080d03b4>] __do_kernel_fault+0x19c/0x280
[<ffffff90080d04dc>] do_bad_area+0x44/0x140
[<ffffff90080d0f9c>] do_translation_fault+0x4c/0x90
[<ffffff9008080a78>] do_mem_abort+0xb8/0x258
[<ffffff90080849d0>] el1_da+0x24/0x3c
[<ffffff9009bde01c>] mtu3_gadget_disconnect+0xac/0x128
[<ffffff9009bd576c>] mtu3_irq+0x34c/0xc18
[<ffffff90082ac03c>] __handle_irq_event_percpu+0x2ac/0xcd0
[<ffffff90082acae0>] handle_irq_event_percpu+0x80/0x138
[<ffffff90082acc44>] handle_irq_event+0xac/0x148
[<ffffff90082b71cc>] handle_fasteoi_irq+0x234/0x568
[<ffffff90082a8708>] generic_handle_irq+0x48/0x68
[<ffffff90082a96ac>] __handle_domain_irq+0x264/0x1740
[<ffffff90080819f4>] gic_handle_irq+0x14c/0x250
[<ffffff9008084cec>] el1_irq+0xec/0x194
[<ffffff90085b985c>] dma_pool_alloc+0x6e4/0xae0
[<ffffff9008d7f890>] cmdq_mbox_pool_alloc_impl+0xb0/0x238
[<ffffff9008d80904>] cmdq_pkt_alloc_buf+0x2dc/0x7c0
[<ffffff9008d80f60>] cmdq_pkt_add_cmd_buffer+0x178/0x270
[<ffffff9008d82320>] cmdq_pkt_perf_begin+0x108/0x148
[<ffffff9008d824d8>] cmdq_pkt_create+0x178/0x1f0
[<ffffff9008f96230>] mtk_crtc_config_default_path+0x328/0x7a0
[<ffffff90090246cc>] mtk_drm_idlemgr_kick+0xa6c/0x1460
[<ffffff9008f9bbb4>] mtk_drm_crtc_atomic_begin+0x1a4/0x1a68
[<ffffff9008e8df9c>] drm_atomic_helper_commit_planes+0x154/0x878
[<ffffff9008f2fb70>] mtk_atomic_complete.isra.16+0xe80/0x19c8
[<ffffff9008f30910>] mtk_atomic_commit+0x258/0x898
[<ffffff9008ef142c>] drm_atomic_commit+0xcc/0x108
[<ffffff9008ef7cf0>] drm_mode_atomic_ioctl+0x1c20/0x2580
[<ffffff9008ebc768>] drm_ioctl_kernel+0x118/0x1b0
[<ffffff9008ebcde8>] drm_ioctl+0x5c0/0x920
[<ffffff900863b030>] do_vfs_ioctl+0x188/0x1820
[<ffffff900863c754>] SyS_ioctl+0x8c/0xa0
Fixes: df2069acb005 ("usb: Add MediaTek USB3 DRD driver")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1604642069-20961-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the following sparse warning:
drivers/usb/misc/brcmstb-usb-pinmap.c:219:6: warning: symbol 'sync_all_pins' was not declared. Should it be static?
The sync_all_pins has only call site within brcmstb-usb-pinmap.c
It should be static
Fixes: 517c4c44b323 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1604050097-91302-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some/many PPMs are simply clearing the change bitfield when a
notification on a port is acknowledge. Unfortunately, doing so means
that any changes between the GET_CONNECTOR_STATUS and ACK_CC_CI commands
is simply lost.
Work around this by re-fetching the connector status afterwards. We can
then infer any changes that we see have happened but that may not be
respresented in the change bitfield.
We end up with the following actions:
1. UCSI_GET_CONNECTOR_STATUS, store result, update unprocessed_changes
2. UCSI_GET_CAM_SUPPORTED, discard result
3. ACK connector change
4. UCSI_GET_CONNECTOR_STATUS, store result
5. Infere lost changes by comparing UCSI_GET_CONNECTOR_STATUS results
6. If PPM reported a new change, then restart in order to ACK
7. Process everything as usual.
The worker is also changed to re-schedule itself if a new change
notification happened while it was running.
Doing this fixes quite commonly occurring issues where e.g. the UCSI
power supply would remain online even thought the ThunderBolt cable was
unplugged.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Link: https://lore.kernel.org/r/20201009144047.505957-3-benjamin@sipsolutions.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Normal commands may be reporting that a connector has changed. Always
call the usci_connector_change handler and let it take care of
scheduling the work when needed.
Doing this makes the ACPI code path identical to the CCG one.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Link: https://lore.kernel.org/r/20201009144047.505957-2-benjamin@sipsolutions.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the following Telit FN980 composition:
0x1055: tty, adb, tty, tty, tty, tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20201103124425.12940-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add following Telit LE910Cx compositions:
0x1203: rndis, tty, adb, tty, tty, tty, tty
0x1230: tty, adb, rmnet, audio, tty, tty, tty, tty
0x1231: rndis, tty, adb, audio, tty, tty, tty, tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20201031225458.10512-1-dnlplm@gmail.com
[ johan: add comments after entries ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The write-URB busy flag was being cleared before the completion handler
was done with the URB, something which could lead to corrupt transfers
due to a racing write request if the URB is resubmitted.
Fixes: 507ca9bc0476 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In Bugzilla #208257, Julien Humbert reports that a 32-GB Kingston
flash drive spontaneously disconnects and reconnects, over and over.
Testing revealed that disabling Link Power Management for the drive
fixed the problem.
This patch adds a quirk entry for that drive to turn off LPM permanently.
CC: Hans de Goede <jwrdegoede@fedoraproject.org>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: Julien Humbert <julroy67@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201102145821.GA1478741@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The devm_ioremap() function doesn't return error pointers, it returns
NULL on error.
Fixes: 517c4c44b323 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201102075655.GA4163205@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.10-rc2
Nothing major as of yet, we're adding support for Intel Alder Lake-S
in dwc3, together with a few fixes that are quite important (memory
leak in raw-gadget, probe crashes in goku_udc, and so on).
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: raw-gadget: fix memory leak in gadget_setup
usb: dwc2: Avoid leaving the error_debugfs label unused
usb: dwc3: ep0: Fix delay status handling
usb: gadget: fsl: fix null pointer checking
usb: gadget: goku_udc: fix potential crashes in probe
usb: dwc3: pci: add support for the Intel Alder Lake-S
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
4 bug fixes for Cadence 3 driver.
The biggest fix is changing endpoint configuration method to
avoid FIFO overflow at multiple endpoints situation.
* tag 'usb-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdns3: gadget: own the lock wrongly at the suspend routine
usb: cdns3: Fix on-chip memory overflow issue
usb: cdns3: gadget: suspicious implicit sign extension
usb: cdns3: Variable 'length' set but not used
|
|
When the system goes to suspend, if the controller is at device mode with
cable connecting to host, the call stack is: cdns3_suspend->
cdns3_gadget_suspend -> cdns3_disconnect_gadget, after cdns3_disconnect_gadget
is called, it owns lock wrongly, it causes the system being deadlock after
resume due to at cdns3_device_thread_irq_handler, it tries to get the lock,
but can't get it forever.
To fix it, we delete the unlock-lock operations at cdns3_disconnect_gadget,
and do it at the caller.
Fixes: b1234e3b3b26 ("usb: cdns3: add runtime PM support")
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Patch fixes issue caused setting On-chip memory overflow bit in usb_sts
register. The issue occurred because EP_CFG register was set twice
before USB_STS.CFGSTS was set. Every write operation on EP_CFG.BUFFERING
causes that controller increases internal counter holding the number
of reserved on-chip buffers. First time this register was updated in
function cdns3_ep_config before delegating SET_CONFIGURATION request
to class driver and again it was updated when class wanted to enable
endpoint. This patch fixes this issue by configuring endpoints
enabled by class driver in cdns3_gadget_ep_enable and others just
before status stage.
Cc: stable@vger.kernel.org#v5.8+
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The code:
trb->length = cpu_to_le32(TRB_BURST_LEN(priv_ep->trb_burst_size)
| TRB_LEN(length));
TRB_BURST_LEN(priv_ep->trb_burst_size) may be overflow for int 32 if
priv_ep->trb_burst_size is equal or larger than 0x80;
Below is the Coverity warning:
sign_extension: Suspicious implicit sign extension: priv_ep->trb_burst_size
with type u8 (8 bits, unsigned) is promoted in priv_ep->trb_burst_size << 24
to type int (32 bits, signed), then sign-extended to type unsigned long
(64 bits, unsigned). If priv_ep->trb_burst_size << 24 is greater than 0x7FFFFFFF,
the upper bits of the result will all be 1.
To fix it, it needs to add an explicit cast to unsigned int type for ((p) << 24).
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Creating debugfs files while loding the spin_lock_irqsave(xhci->lock)
creates a lock dependecy that could possibly deadlock.
Lockdep warns:
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
5.10.0-rc1pdx86+ #8 Not tainted
-----------------------------------------------------
systemd-udevd/386 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
ffffffffb1a94038 (pin_fs_lock){+.+.}-{2:2}, at: simple_pin_fs+0x22/0xa0
and this task is already holding:
ffff9e7b87fbc430 (&xhci->lock){-.-.}-{2:2}, at: xhci_alloc_streams+0x5f9/0x810
which would create a new lock dependency:
(&xhci->lock){-.-.}-{2:2} -> (pin_fs_lock){+.+.}-{2:2}
Create the files a bit later after lock is released.
Fixes: 673d74683627 ("usb: xhci: add debugfs support for ep with stream")
CC: Li Jun <jun.li@nxp.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some platform of AMD, S3 fails with HCE and SRE errors. To fix this,
need to disable a bit which is enable in sparse controller.
Cc: stable@vger.kernel.org #v4.19+
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
An incorrect sizeof() is being used, sizeof(rhub->ports) is not
correct, it should be sizeof(*rhub->ports). This bug did not
cause any issues because it just so happens the sizes are the same.
Fixes: bcaa9d5c5900 ("xhci: Create new structures to store xhci port information")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|