| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The sparse tool complains as follows:
drivers/usb/typec/tcpm/tcpci.c:118:5: warning:
symbol 'tcpci_apply_rc' was not declared. Should it be static?
This symbol is not used outside of tcpci.c, so marks it static.
Fixes: 7257fbc7c598 ("usb: typec: tcpci: Implement callback for apply_rc")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210524133704.2432555-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
APPLY RC is defined as ROLE_CONTROL.CC1 != ROLE_CONTROL.CC2 and
POWER_CONTROL.AutodischargeDisconnect is 0. When ROLE_CONTROL.CC1 ==
ROLE_CONTROL.CC2, set the other CC to OPEN.
Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When vbus auto discharge is enabled, TCPCI based TCPC transitions
into Attached.SNK/Attached.SRC state. During PR_SWAP, TCPCI based
TCPC would disconnect when partner changes power roles. TCPC has
to be moved APPLY RC state during PR_SWAP. This is done by
ROLE_CONTROL.CC1 != ROLE_CONTROL.CC2 and
POWER_CONTROL.AutodischargeDisconnect is 0. Once the swap sequence
is done, AutoDischargeDisconnect is re-enabled.
Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The logic to enable vbus auto discharge on disconnect is used in
more than one place. Since this is repetitive code, moving this into
its own method.
Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During PR_SWAP, When TCPM is in PR_SWAP_SNK_SRC_SINK_OFF, vbus is
expected to reach VSAFE0V when source turns off vbus. Do not move
to SNK_UNATTACHED state when this happens.
Fixes: 28b43d3d746b ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The top comment in the file wrongly uses kernel doc format:
.../typec/tcpm/wcove.c:17: warning: expecting prototype for typec_wcove.c - WhiskeyCove PMIC USB Type(). Prototype was for WCOVE_CHGRIRQ0() instead
Fix this by converting it to plain comment.
Fixes: ae8a2ca8a221 ("usb: typec: Group all TCPCI/TCPM code together")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210519085527.48657-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver fixes for driver core changes that happened in
5.13-rc1.
The clk driver fix resolves a many-reported issue with booting some
devices, and the USB typec fix resolves the reported problem of USB
systems on some embedded boards.
Both of these have been in linux-next this week with no reported
issues"
* tag 'driver-core-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
clk: Skip clk provider registration when np is NULL
usb: typec: tcpm: Don't block probing of consumers of "connector" nodes
|
|
This is a regression introduced by 1373fefc6243 ("usb: typec: tcpm:
Allow slow charging loops to comply to pSnkStby")
When Source advertises Rp-default, tcpm would request 500mA when in
SINK_DISCOVERY, Type-C spec advises the sink to follow BC1.2 current
limits when Rp-default is advertised.
[12750.503381] Requesting mux state 1, usb-role 2, orientation 1
[12750.503837] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[12751.003891] state change SNK_STARTUP -> SNK_DISCOVERY
[12751.003900] Setting voltage/current limit 5000 mV 500 mA
This patch restores the behavior where the tcpm would request 0mA when
Rp-default is advertised by the source.
[ 73.174252] Requesting mux state 1, usb-role 2, orientation 1
[ 73.174749] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[ 73.674800] state change SNK_STARTUP -> SNK_DISCOVERY
[ 73.674808] Setting voltage/current limit 5000 mV 0 mA
During SNK_DISCOVERY, Cap the current limit to PD_P_SNK_STDBY_MW / 5 only
for slow_charger_loop case.
Fixes: 1373fefc6243 ("usb: typec: tcpm: Allow slow charging loops to comply to pSnkStby")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210510211756.3346954-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fw_devlink expects DT device nodes with "compatible" property to have
struct devices created for them. Since the connector node might not be
populated as a device, mark it as such so that fw_devlink knows not to
wait on this fwnode being populated as a struct device.
Without this patch, USB functionality can be broken on some boards.
Fixes: f7514a663016 ("of: property: fw_devlink: Add support for remote-endpoint")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210506004423.345199-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Not_Supported Message is acceptable in VDM AMS. Redirect the VDM state
machine to VDM_STATE_DONE when receiving Not_Supported and finish the
VDM AMS.
Also, after the loop in vdm_state_machine_work, add more conditions of
VDM states to clear the vdm_sm_running flag because those are all
stopping states when leaving the loop.
In addition, finish the VDM AMS if the port partner responds BUSY.
Fixes: 8dea75e11380 ("usb: typec: tcpm: Protocol Error handling")
Fixes: 8d3a0578ad1a ("usb: typec: tcpm: Respond Wait if VDM state machine is running")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210507062300.1945009-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In current design, DISCOVER_IDENTITY is queued to VDM state machine
immediately in Ready states and never retries if it fails in the AMS.
Move the process to a delayed work so that when it fails for some
reasons (e.g. Sink Tx No Go), it can be retried by queueing the work
again. Also fix a problem that the vdm_state is not set to a proper
state if it is blocked by Collision Avoidance mechanism.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210507062300.1945009-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After receiving Sink Capabilities Message in GET_SINK_CAP AMS, it is
incorrect to call tcpm_pd_handle_state because the Message is expected
and the current state is not Ready states. The result of this incorrect
operation ends in Soft Reset which is definitely wrong. Simply
forwarding to Ready States is enough to finish the AMS.
Fixes: 8dea75e11380 ("usb: typec: tcpm: Protocol Error handling")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503171849.2605302-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
Fixes: e3a072022487 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210415050121.1928298-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a PD charger advertising Rp-3.0 is connected to a sink port, the
sink port current limit would 3A, during SNK_DISCOVERY, till power
negotiation starts. Once the negotiation starts the power limit needs
to drop down to pSnkStby(500mA @ 5V) and to negotiated current limit
once the explicit contract is in place. Not all charging loops can ramp
up to 3A and drop down to 500mA within tSnkStdby which is 15ms. The port
partner might hard reset if tSnkStdby is not met.
To solve this problem, this patch introduces slow-charger-loop which
when set makes the port request PD_P_SNK_STDBY_MW upon entering
SNK_DISCOVERY(instead of 3A or the 1.5A during SNK_DISCOVERY) and the
actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during
SNK_READY for non-pd link.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
>From PD Spec:
The Sink Shall transition to Sink Standby before a positive or
negative voltage transition of VBUS. During Sink Standby
the Sink Shall reduce its power draw to pSnkStdby. This allows
the Source to manage the voltage transition as well as
supply sufficient operating current to the Sink to maintain PD
operation during the transition. The Sink Shall
complete this transition to Sink Standby within tSnkStdby
after evaluating the Accept Message from the Source. The
transition when returning to Sink operation from Sink Standby
Shall be completed within tSnkNewPower. The
pSnkStdby requirement Shall only apply if the Sink power draw
is higher than this level.
The above requirement needs to be met to prevent hard resets
from port partner.
Without the patch: (5V/3A during SNK_DISCOVERY all the way through
explicit contract)
[ 95.711984] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 95.712007] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 95.712017] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 95.837190] VBUS on
[ 95.882075] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 95.882082] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[ 95.882086] polarity 1
[ 95.883151] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[ 95.883441] enable vbus discharge ret:0
[ 95.883445] Requesting mux state 1, usb-role 2, orientation 2
[ 95.883776] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[ 95.883879] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[ 96.038960] VBUS on
[ 96.383939] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[ 96.383946] Setting voltage/current limit 5000 mV 3000 mA
[ 96.383961] vbus=0 charge:=1
[ 96.386044] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[ 96.386309] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[ 96.394404] PD RX, header: 0x2161 [1]
[ 96.394408] PDO 0: type 0, 5000 mV, 3000 mA [E]
[ 96.394410] PDO 1: type 0, 9000 mV, 2000 mA []
[ 96.394412] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[ 96.394416] Setting usb_comm capable false
[ 96.395083] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[ 96.395089] Requesting PDO 1: 9000 mV, 2000 mA
[ 96.395093] PD TX, header: 0x1042
[ 96.397404] PD TX complete, status: 0
[ 96.397424] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[ 96.400826] PD RX, header: 0x363 [1]
[ 96.400829] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[ 96.400832] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[ 96.577315] PD RX, header: 0x566 [1]
[ 96.577321] Setting voltage/current limit 9000 mV 2000 mA
[ 96.578363] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[ 96.578370] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]
With the patch:
[ 168.398573] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 168.398605] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 168.398619] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 168.522348] VBUS on
[ 168.568676] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 168.568684] state change SNK_DEBOUNCED -> SNK_ATTACHED [rev3 NONE_AMS]
[ 168.568688] polarity 1
[ 168.569867] set_auto_vbus_discharge_threshold mode:0 pps_active:n vbus:5000 ret:0
[ 168.570158] enable vbus discharge ret:0
[ 168.570161] Requesting mux state 1, usb-role 2, orientation 2
[ 168.570504] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[ 168.570634] pending state change SNK_STARTUP -> SNK_DISCOVERY @ 500 ms [rev3 NONE_AMS]
[ 169.070689] state change SNK_STARTUP -> SNK_DISCOVERY [delayed 500 ms]
[ 169.070695] Setting voltage/current limit 5000 mV 3000 mA
[ 169.070702] vbus=0 charge:=1
[ 169.072719] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
[ 169.073145] pending state change SNK_WAIT_CAPABILITIES -> HARD_RESET_SEND @ 450 ms [rev3 NONE_AMS]
[ 169.077162] PD RX, header: 0x2161 [1]
[ 169.077172] PDO 0: type 0, 5000 mV, 3000 mA [E]
[ 169.077178] PDO 1: type 0, 9000 mV, 2000 mA []
[ 169.077183] state change SNK_WAIT_CAPABILITIES -> SNK_NEGOTIATE_CAPABILITIES [rev2 POWER_NEGOTIATION]
[ 169.077191] Setting usb_comm capable false
[ 169.077753] cc=0 cc1=0 cc2=5 vbus=0 vconn=sink polarity=1
[ 169.077759] Requesting PDO 1: 9000 mV, 2000 mA
[ 169.077762] PD TX, header: 0x1042
[ 169.079990] PD TX complete, status: 0
[ 169.080013] pending state change SNK_NEGOTIATE_CAPABILITIES -> HARD_RESET_SEND @ 60 ms [rev2 POWER_NEGOTIATION]
[ 169.083183] VBUS on
[ 169.084195] PD RX, header: 0x363 [1]
[ 169.084200] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_TRANSITION_SINK [rev2 POWER_NEGOTIATION]
[ 169.084206] Setting standby current 5000 mV @ 500 mA
[ 169.084209] Setting voltage/current limit 5000 mV 500 mA
[ 169.084220] pending state change SNK_TRANSITION_SINK -> HARD_RESET_SEND @ 500 ms [rev2 POWER_NEGOTIATION]
[ 169.260222] PD RX, header: 0x566 [1]
[ 169.260227] Setting voltage/current limit 9000 mV 2000 mA
[ 169.261315] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:9000 ret:0
[ 169.261321] state change SNK_TRANSITION_SINK -> SNK_READY [rev2 POWER_NEGOTIATION]
[ 169.261570] AMS POWER_NEGOTIATION finished
Fixes: f0690a25a140b ("staging: typec: USB Type-C Port Manager (tcpm)")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for altmodes described in the usb-connector fwnode
associated with the Type-C controller by calling the new
typec_port_register_altmodes_from_fwnode() helper for this.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
power_supply_changed needs to be called to notify clients
after the partner accepts the requested values for the pps
case.
Also, remove the redundant power_supply_changed at the end
of the tcpm_reset_port as power_supply_changed is already
called right after usb_type is changed.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm_pd_select_pps_apdo overwrites port->pps_data.min_volt,
port->pps_data.max_volt, port->pps_data.max_curr even before
port partner accepts the requests. This leaves incorrect values
in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values in req_min_volt, req_max_volt, req_max_curr, req_out_volt,
req_op_curr. min_volt, max_volt, max_curr gets updated once the
partner accepts the request. current_limit, supply_voltage gets updated
once local port's tcpm enters SNK_TRANSITION_SINK when the accepted
current_limit and supply_voltage is enforced.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm_pd_build_request overwrites current_limit and supply_voltage
even before port partner accepts the requests. This leaves stale
values in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values of current limit/supply voltage in req_current_limit
and req_supply_voltage. current_limit/supply_voltage gets updated
once the port partner accepts the request.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sparse tool complains as follows:
drivers/usb/typec/tcpm/tcpci_maxim.c:55:34: warning:
symbol 'max_tcpci_tcpci_write_table' was not declared. Should it be static?
This symbol is not used outside of tcpci_maxim.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210324144253.1011234-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the usb/thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When port partner responds "Not supported" to the DiscIdentity command,
VDM state machine can remain in NVDM_STATE_ERR_TMOUT and this causes
querying sink cap to be skipped indefinitely. Hence check for
vdm_sm_running instead of checking for VDM_STATE_DONE.
Fixes: 8dc4bd073663f ("usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210318064805.3747831-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
>From 6.4.4.2 Structured VDM:
• Either Port May be an Initiator of Structured VDMs except for the Enter
Mode and Exit Mode Commands which Shall only be initiated by the DFP."
The above implies that when PD3.0 link is established PD3.0 sinks
can send out discover identity command/AMS once PD negotiation is done.
This allows discovering identity for PD3.0 UFP ports as well.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210318065604.3757307-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change adds some of the register bit definitions from the TCPCI spec:
https://www.usb.org/sites/default/files/documents/
usb-port_controller_specification_rev2.0_v1.0_0.pdf
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210316221304.391206-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm-source-psy- does not invoke power_supply_changed API when
one of the published power supply properties is changed.
power_supply_changed needs to be called to notify
userspace clients(uevents) and kernel clients.
Fixes: f2a8aa053c176 ("typec: tcpm: Represent source supply through power_supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210317181249.1062995-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Defining one macro instead of two for tcpc_presenting_*_rd.
This is a follow up of the comment left by Heikki Krogerus.
https://patchwork.kernel.org/project/linux-usb/patch/
20210304070931.1947316-1-badhri@google.com/
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210310223536.3471243-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This function always return '0' and no callers use the return value.
So make it a void function.
This eliminates the following coccicheck warning:
./drivers/usb/typec/tcpm/tcpm.c:778:5-8: Unneeded variable: "ret".
Return "0" on line 794
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1615185330-118246-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.
>From the TCPCI spec:
4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.
Table 4-22. CC_STATUS Register Definition:
If (ROLE_CONTROL.CC1 = Rd) or ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp-1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp-3.0A
If (ROLE_CONTROL.CC2=Rd) or (ConnectResult=1)
00b: SNK.Open (Below maximum vRa)
01b: SNK.Default (Above minimum vRd-Connect)
10b: SNK.Power1.5 (Above minimum vRd-Connect) Detects Rp 1.5A
11b: SNK.Power3.0 (Above minimum vRd-Connect) Detects Rp 3.0A
Fixes: 74e656d6b0551 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210304070931.1947316-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The single debugfs file for this driver really is a log file, so make a
subdir and call it "log" to make it obvious this is what it is for.
This makes cleanup simpler as we just remove the whole directory, no
need to handle individual files anymore.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210216144645.3813043-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The single debugfs file for this driver really is a log file, so make a
subdir and call it "log" to make it obvious this is what it is for.
This makes cleanup simpler as we just remove the whole directory, no
need to handle individual files anymore.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210216144645.3813043-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When vbus auto discharge is enabled, TCPM can sometimes be faster than
the TCPC i.e. TCPM can go ahead and move the port to unattached state
(involves disabling vbus auto discharge) before TCPC could effectively
discharge vbus to VSAFE0V. This leaves vbus with residual charge and
increases the decay time which prevents tsafe0v from being met.
This change makes TCPM waits for a maximum of tSafe0V(max) for vbus
to discharge to VSAFE0V before transitioning to unattached state
and re-enable toggling. If vbus discharges to vsafe0v sooner, then,
transition to unattached state
happens right away.
Also, while in SNK_READY, when auto discharge is enabled, drive
disconnect based on vbus turning off instead of Rp disappearing on
CC pins. Rp disappearing on CC pins is almost instanteous compared
to vbus decay.
Sink detach:
[ 541.703058] CC1: 3 -> 0, CC2: 0 -> 0 [state SNK_READY, polarity 0, disconnected]
[ 541.703331] Setting voltage/current limit 5000 mV 0 mA
[ 541.727235] VBUS on
[ 541.749650] VBUS off
[ 541.749653] pending state change SNK_READY -> SNK_UNATTACHED @ 650 ms [rev3 NONE_AMS]
[ 541.749944] VBUS VSAFE0V
[ 541.749945] state change SNK_READY -> SNK_UNATTACHED [rev3 NONE_AMS]
[ 541.750806] Disable vbus discharge ret:0
[ 541.907345] Start toggling
[ 541.922799] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
Source detach:
[ 2555.310414] state change SRC_SEND_CAPABILITIES -> SRC_READY [rev3 POWER_NEGOTIATION]
[ 2555.310675] AMS POWER_NEGOTIATION finished
[ 2555.310679] cc:=3
[ 2593.645886] CC1: 0 -> 0, CC2: 2 -> 0 [state SRC_READY, polarity 1, disconnected]
[ 2593.645919] pending state change SRC_READY -> SNK_UNATTACHED @ 650 ms [rev3 NONE_AMS]
[ 2593.648419] VBUS off
[ 2593.648960] VBUS VSAFE0V
[ 2593.648965] state change SRC_READY -> SNK_UNATTACHED [rev3 NONE_AMS]
[ 2593.649962] Disable vbus discharge ret:0
[ 2593.890322] Start toggling
[ 2593.925663] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0,
Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210225101104.1680697-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit a079973f462a ("usb: typec: tcpm: Remove tcpc_config
configuration mechanism") removed the tcpc_config which includes the
Sink VDO and it is not yet added back with fwnode. Add it now.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-8-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD Spec Revision 3.0 Version 2.0 + ECNs 2020-12-10
6.4.4.2.3 Structured VDM Version
"The Structured VDM Version field of the Discover Identity Command
sent and received during VDM discovery Shall be used to determine the
lowest common Structured VDM Version supported by the Port Partners or
Cable Plug and Shall continue to operate using this Specification
Revision until they are Detached."
Also clear the fields newly defined in SVDM version 2.0 if the
negotiated SVDM version is 1.0.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD Rev 3.0 introduces SVDM Version 2.0. This patch makes the field
configuable in the header in order to be able to be compatible with
older SVDM version.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210205033415.3320439-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Configure USB switches when partner is USB Communication capable.
The is enabled USB data communication over D+/D- pins.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210202003101.221145-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB Communications Capable bit indicates if port
partner is capable of communication over the USB data lines
(e.g. D+/- or SS Tx/Rx). TCPM passes this information for chip specific
operations.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210202003101.221145-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB Communications Capable bit indicates if port
partner is capable of communication over the USB data lines
(e.g. D+/- or SS Tx/Rx). Notify the status of the bit to low
level drivers to perform chip specific operation.
For instance, low level driver enables USB switches on D+/D-
lines to set up data path when the bit is set.
Refactored from patch initially authored by
Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210202003101.221145-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Receiving the first packet in an AMS sequence signals the
beginning of AMS. Set in_ams flag to true when SRC_CAPS are
received during POWER_NEGOTIATION AMS.
This fixes the failure flagged while running TD.PD.SNK.E9
compliance test.
>From Deterministic PD compliance MOI spec:
TD.PD.SNK.E9. GetSinkCap in Place of Accept
Description:
As Provider, the Tester intentionally sends a GetSinkCap message in place
of Accept message and verifies the UUT will send a SoftReset and recover
from the error.
Steps:
a) Run PROC.PD.E1 Bring-up according to the UUT role.
b) The Tester cycles VBus.
c) The Tester sends a Source Capabilities message to the UUT.
d) Upon receipt of a Request message from the UUT, the Tester replies with
a GoodCRC message.
e) The Tester sends a GetSinkCap message to the UUT.
f) If a SoftReset is not received within 15 ms after the GetSinkCap EOP was
sent, the test fails.
g) If a SoftReset is received timely, the Tester replies with an Accept
message.
h) The Tester sends Source Capabilities message to the UUT repeatedly until
nCapsCount reached or a GoodCRC is received. If nCapsCount reached, the
test fails.
i) If a Request is not received timely within 30 ms after the GoodCRC EOP
corresponding to Source Capabilities message was received, the test
fails.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210202033859.258491-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While in source mode, vbus could be shutoff by protections
circuits. TCPM does not move back to toggling state to
re-initiate connection. Fix this by moving to SRC_UNATTACHED
state when vbus shuts off while in source mode.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210201100212.49863-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add terminating '\n' to the formats where missed.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210124143947.1688-1-angkery@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PTR_ERR(chip->tcpci) has been used as a return value,
it is not necessary to assign it to ret, so remove it.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210124143853.1630-1-angkery@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the port partner is PD2, the PDOs of the local port should follow the
format defined in PD2 Spec. Dynamically modify the pre-defined PD3 PDOs
and transform them into PD2 format before sending them to the PD2 port
partner.
Reviewed-by: Guenter Roeck <linux@roeckus.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210115163311.391332-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver includes the legacy GPIO header <linux/gpio.h>,
the new GPIO header <linux/gpio/consumer.h> and
the deprecated OF GPIO header <linux/of_gpio.h> yet
fail to use symbols from any of them, so drop these
includes.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210120225045.173556-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Port partner could send PR_SWAP/DR_SWAP/VCONN_SWAP/Request just after it
enters Ready states. This will cause conficts if the port is going to
send DISC_IDENT in the Ready states of TCPM. Set a flag indicating that
the state machine is processing VDM and respond Wait messages until the
VDM state machine stops.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD3.0 Spec 6.8.1 describes how to handle Protocol Error. There are
general rules defined in Table 6-61 which regulate incoming Message
handling. If the incoming Message is unexpected, unsupported, or
unrecognized, Protocol Error occurs. Follow the rules to handle these
situations. Also consider PD2.0 connection (PD2.0 Spec Table 6-36) for
backward compatibilities.
To know the types of AMS in all the recipient's states, identify those
AMS who are initiated by the port partner but not yet recorded in the
current code.
Besides, introduce a new state CHUNK_NOT_SUPP to delay the NOT_SUPPORTED
message after receiving a chunked message.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch provides the implementation of Collision Avoidance introduced
in PD3.0. The start of each Atomic Message Sequence (AMS) initiated by
the port will be denied if the current AMS is not interruptible. The
Source port will set the CC to SinkTxNG if it is going to initiate an
AMS, and SinkTxOk otherwise. Meanwhile, any AMS initiated by a Sink port
will be denied in TCPM if the port partner (Source) sets SinkTxNG except
for HARD_RESET and SOFT_RESET.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085553.2982-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During init, vbus_vsafe0v does not get updated till the first
connect as a sink. This causes TCPM to be stuck in SRC_ATTACH_WAIT
state while booting with a sink (For instance: a headset) connected.
[ 1.429168] Start toggling
[ 1.439907] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 1.445242] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 53.358528] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 53.358564] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
Fix this by updating vbus_vsafe0v based on vbus_present status
on boot.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071911.2205197-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Auto discharge circuits kick in only when vbus decays and reaches
VBUS_SINK_DISCONNECT_THRESHOLD threshold. Enable bleed discharge to
discharge vbus to VBUS_SINK_DISCONNECT_THRESHOLD upon disconnect.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071145.2199997-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"Table 4-19. POWER_CONTROL Register Definition" from tcpci spec
defines BIT(3) as the control bit for bleed discharge.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Kyle Tso <kyletso@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
