summaryrefslogtreecommitdiffstats
path: root/drivers/usb/storage
AgeCommit message (Collapse)AuthorFilesLines
2014-04-16uas: fix deadlocky memory allocationsOliver Neukum1-2/+2
There are also two allocations with GFP_KERNEL in the pre-/post_reset code paths. That is no good because that is a part of the SCSI error handler. Signed-off-by: Oliver Neukum <oliver@neukum.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-16uas: fix error handling during scsi_scan()Oliver Neukum1-1/+2
intfdata is set only after scsi_scan(). uas_pre_reset() however needs intfdata to be valid and will follow the NULL pointer killing khubd. intfdata must be preemptively set before the host is registered and undone in the error case. Signed-off-by: Oliver Neukum <oliver@neukum.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-16uas: fix GFP_NOIO under spinlockOliver Neukum1-3/+3
Quote Dan: The patch e36e64930cff: "uas: Use GFP_NOIO rather then GFP_ATOMIC where possible" from Nov 7, 2013, leads to the following static checker warning: drivers/usb/storage/uas.c:806 uas_eh_task_mgmt() error: scheduling with locks held: 'spin_lock:lock' Some other allocations under spinlock are not caught. The fix essentially reverts e36e64930cffd94e1c37fdb82f35989384aa946b Signed-off-by: Oliver Neukum <oliver@neukum.org> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-04storage: accept some UAS devices if streams are unavailableOliver Neukum1-0/+4
On some older XHCIs streams are not supported and the UAS driver will fail at probe time. For those devices storage should try to bind to UAS devices. This patch adds a flag for stream support to HCDs and evaluates it. [Note: Sarah fixed a bug where the USB 2.0 root hub, not USB 3.0 root hub would get marked as being able to support streams.] Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
2014-03-04uas: Remove comment about registering a uas scsi controller for each usb busHans de Goede1-6/+0
Although an interesting concept, I don't think that this is a good idea: -This will result in lots of "virtual" scsi controllers confusing users -If we get a scsi-bus-reset we will now need to do a usb-device-reset of all uas devices on the same usb bus, which is something to avoid if possible Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Add Hans de Goede as uas maintainerHans de Goede1-1/+3
At the kernel-summit Sarah Sharp asked me if I was willing to become the uas maintainer. I said yes, and here is a patch to make this official. Also remove Matthew Wilcox and Sarah Sharp as maintainers at their request. I've also added myself to the module's author tag, so that if people look there rather then in maintainers they will know they should bug me about uas too. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: remove BROKENGerd Hoffmann1-1/+1
xhci streams support is fixed, unblock usb attached scsi. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Make sure sg elements are properly alignedHans de Goede1-0/+18
Copy the sg alignment trick from the usb-storage driver, without this I'm seeing intermittent errors when using uas devices with an ehci controller. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Add some data in/out ready iu sanity checksHans de Goede1-0/+10
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Improve error reportingHans de Goede1-14/+46
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Use the right error codes for different kinds of errorsHans de Goede1-9/+10
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Clear cmdinfo on command queue-ingHans de Goede1-0/+2
The scsi error handling path re-uses previously queued up (and errored-out) cmds. If such a re-used cmd had a data-phase then cmdinfo will have data_in_urb / data_out_urb still set to the free-ed urbs from the errored-out cmd, and they will get free-ed a second time when the error handling cmd completes, corrupting the kernel heap. Clearing cmdinfo on command queue-ing fixes this, and seems like a good idea in general. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Fix memory managementHans de Goede1-19/+14
The scsi-host structure is refcounted, scsi_remove_host tears down the scsi-host but does not decrement the refcount, so we need to call scsi_put_host on disconnect to get the underlying memory to be freed. After calling scsi_remove_host, the scsi-core may still hold a reference to the scsi-host, iow we may still get called after uas_disconnect, but we do our own life cycle management of uas_devinfo, freeing it on disconnect, and thus may end up using devinfo after it has been freed. Switch to letting scsi_host_alloc allocate and manage the memory for us. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Fix command / task mgmt submission racing with disconnectHans de Goede1-1/+14
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: cmdinfo: use only one list headHans de Goede1-12/+8
cmds are either on the inflight list or on the dead list, never both, so we only need one list head. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: add uas_mark_cmd_dead helper functionHans de Goede1-17/+18
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Properly complete inflight commands on bus-reset or disconnectHans de Goede1-20/+21
Before this commit the uas driver would keep track of scsi commands which still need to have some urbs submitted to the device, and complete this with an ABORT result code on bus-reset or disconnect, but in flight scsi commands which have all their urbs submitted, and thus are not part of the work list, would never get their done callback called. The problem is killed sense urbs don't have any tag info, so it is impossible to tell which scsi cmd they belong to, so merely making sure all the urbs have completed one way or the other is not enough. This commit fixes this by changing the work list to an inflight list, which keeps tracks of all inflight scsi cmnds, using the IS_IN_WORK_LIST flag to determine if actual work needs to be done in uas_do_work(), and by moving marking all inflight scsi commands as aborted and moving them to the dead list on bus-reset or disconnect. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: uas_alloc_data_urb: Remove unnecessary use_streams checkHans de Goede1-2/+1
uas_alloc_data_urb always gets called with a stream_id value of 0 when not using streams. Removing the check makes it consistent with uas_alloc_sense_urb. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Fix task-management not working when connected over USB-2Hans de Goede1-1/+2
For USB-2 connections the stream-id must always be 0. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Reset device on rebootHans de Goede1-0/+30
Some BIOS-es will hang on reboot when an uas device is attached and left in uas mode on reboot. This commit adds a shutdown handler which on reboot puts the device back into usb-storage mode, fixing the hang on reboot on these systems. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Add suspend/resume supportHans de Goede1-0/+42
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Use GFP_NOIO rather then GFP_ATOMIC where possibleHans de Goede1-3/+3
We can sleep in our own workqueue (which is the whole reason for having it), and scsi error handlers are also always called from a context which may sleep. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Don't allow more then one task to run at the same timeHans de Goede1-5/+34
Since we use a fixed tag / stream for tasks we cannot allow more then one to run at the same time. This could happen before this time if a task timed out. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: task_mgmt: Kill the sense-urb if we fail to submit the cmd urbHans de Goede1-11/+13
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Not being able to alloc streams when connected through usb-3 is an errorHans de Goede1-7/+17
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Verify endpoint descriptors from uas_use_uas_driver()Hans de Goede1-1/+11
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Drop fixed endpoint config handlingHans de Goede1-25/+11
The fixed endpoint config code was only necessary to deal with an early uas prototype which has never been released, so lets drop it and enforce proper uas endpoint descriptors. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Move uas_find_endpoints to uas-detect.hHans de Goede2-27/+27
No changes, just the move. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Fix bounds check in uas_find_endpointsHans de Goede1-1/+1
The loop uses up to 3 bytes of the endpoint extra data. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Add uas_find_endpoints() helper functionHans de Goede1-11/+23
This is a preparation patch for adding better descriptor validation. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Honor no-uas quirk set in usb-storage's quirks module parameterHans de Goede2-1/+5
Falling back from uas to usb-storage requires coordination between uas and usb-storage, so use usb-storage's quirks module parameter, rather then requiring the user to pass a param to 2 different modules. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04usb-storage: Modify and export adjust_quirks so that it can be used by uasHans de Goede2-6/+13
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04usb-storage: Don't bind to uas devices if the uas driver is enabledHans de Goede2-0/+15
uas devices have 2 alternative settings on their usb-storage interface, one for usb-storage and one for uas. Using the uas driver is preferred, so if the uas driver is enabled, and the device has an uas alt setting, don't bind. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Add the posibilty to blacklist uas devices from using the uas driverHans de Goede3-4/+76
Once we start supporting uas hardware, and as more and more uas devices become available, we will likely start seeing broken devices. This patch prepares for the inevitable need for blacklisting those devices from using the uas driver (they will use usb-storage instead). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Move uas detect code to uas-detect.hHans de Goede2-38/+42
This is a preparation patch for teaching usb-storage to not bind to uas devices. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Add a uas_find_uas_alt_setting helper functionHans de Goede1-5/+16
This is a preparation patch for teaching usb-storage to not bind to uas devices. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Use all available stream idsHans de Goede1-3/+3
If we get ie 16 streams we can use stream-id 1-16, not 1-15. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: s/response_ui/response_iu/Hans de Goede1-1/+1
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Fix reset handling for externally triggered resetHans de Goede1-5/+31
Handle usb-device resets not triggered from uas_eh_bus_reset_handler(), when this happens, disable cmd queuing during the reset, and wait for existing requests to finish in pre_reset. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Fix reset lockingHans de Goede1-0/+9
Fix the uas_eh_bus_reset_handler not properly taking the usbdev lock before calling usb_device_reset, the usb-core expects this lock to be taken when usb_device_reset is called. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Fix uas not working when plugged into an ehci portHans de Goede1-4/+4
I thought it would be a good idea to also test uas with usb-2, and it turns out it was, as it did not work. The problem is that the uas driver was passing the bEndpointAddress' direction bit to usb_rcvbulkpipe, the xhci code seems to not care about this, but with the ehci code this causes usb_submit_urb failure. With this fixed the uas code works nicely with an uas device plugged into an ehci port. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: uas_alloc_cmd_urb: drop unused stream_id parameterHans de Goede1-3/+2
The cmd endpoint never has streams, so the stream_id parameter is unused. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Avoid unnecessary unlock / lock calls around unlink_data_urbsHans de Goede1-13/+7
All callers of unlink_data_urbs drop devinfo->lock before calling it, and then immediately take it again after the call. And the first thing unlink_data_urbs does is take the lock again, and the last thing it does is drop it. This commit removes all the unnecessary lock dropping and taking. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Properly set interface to altsetting 0 on probe failureHans de Goede1-9/+9
- Rename labels to properly reflect this - Don't skip free-ing the streams when scsi_init_shared_tag_map fails Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: Urbs must be anchored before submitting themHans de Goede1-8/+12
Otherwise they may complete before they get anchored and thus never get unanchored (as the unanchoring is done by the usb core on completion). This commit also remove the usb_get_urb / usb_put_urb around cmd submission + anchoring, since if done in the proper order this is not necessary. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: replace BUG_ON() + WARN_ON() with WARN_ON_ONCE()Gerd Hoffmann1-9/+10
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: add dead request listGerd Hoffmann1-8/+42
This patch adds a new list where all requests which are canceled are added to, so we don't loose them. Then, after killing all inflight urbs on bus reset (and disconnect) we'll walk over the list and clean them up. Without this we can end up with aborted requests lingering around in case of status pipe transfer errors. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: make work list per-deviceGerd Hoffmann1-62/+44
Simplifies locking, we'll protect the list with the device spin lock. Also plugs races which can happen when two devices operate on the global list. While being at it rename the list head from "list" to "work", preparing for the addition of a second list. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-03-04uas: properly reinitialize in uas_eh_bus_reset_handlerGerd Hoffmann1-0/+5
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2014-02-04usb-storage: enable multi-LUN scanning when neededAlan Stern2-1/+9
People sometimes create their own custom-configured kernels and forget to enable CONFIG_SCSI_MULTI_LUN. This causes problems when they plug in a USB storage device (such as a card reader) with more than one LUN. Fortunately, we can tell fairly easily when a storage device claims to have more than one LUN. When that happens, this patch asks the SCSI layer to probe all the LUNs automatically, regardless of the config setting. The patch also updates the Kconfig help text for usb-storage, explaining that CONFIG_SCSI_MULTI_LUN may be necessary. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Thomas Raschbacher <lordvan@lordvan.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> CC: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-12 13:30:54 +0000