summaryrefslogtreecommitdiffstats
path: root/drivers/usb/serial/ftdi_sio.c
AgeCommit message (Collapse)AuthorFilesLines
2010-03-02USB: ftdi_sio: remove unnecessary initialisationsJohan Hovold1-9/+9
Return values are being initialised to zero only to be unconditionally assigned to a few instructions later. This may give the impression that zero is returned on success, which is not the case. Note also that ftdi_NDI_device_setup never reports errors. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02USB: ftdi_sio: clean up modem status handlingJohan Hovold1-21/+16
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02USB: ftdi_sio: fix DMA buffers on stackJohan Hovold1-42/+27
Also remove unnecessary buffer allocations for zero-length transfers. Reported-by: Matti Aarnio <matti.aarnio@zmailer.org> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02USB: ftdi_sio: fix latency-timeout endianess bugJohan Hovold1-4/+10
Also fixes DMA transfer to stack for latency buffer. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02USB: ftdi_sio: use error code from usb stack in read_latency_timerJohan Hovold1-3/+2
Use same semantics as for write_latency_timer. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02USB: ftdi_sio: remove support for 5 and 6 data bitsMark Adamson1-3/+1
Removed CS5 and CS6 from data bits since these are not supported in FTDI hardware. Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02USB: ftdi_sio: fix initialisation of latency timeoutJohan Hovold1-4/+5
Latency timeout was read but never stored on port probe. When ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0 rather than the default 16ms. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02USB: ftdi_sio: remove obsolete commentJohan Hovold1-2/+1
We always push characters to ldisc immediately regardless of ASYNC_LOW_LATENCY. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02USB: ftdi_sio: fix error message on closeJohan Hovold1-1/+1
Resubmitting read urb fails with -EPERM if completion handler runs while urb is being killed on close. This should not be reported as an error. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-02-16USB: ftdi_sio: add device IDs (several ELV, one Mindstorms NXT)Andreas Mohr1-3/+21
- add FTDI device IDs for several ELV devices and NXTCam of Lego Mindstorms NXT - add hopefully helpful new_id comment - remove less helpful "Due to many user requests for multiple ELV devices we enable them by default." comment (we simply add _all_ known devices - an enduser shouldn't have to fiddle with obscure module parameters...). - add myself to DRIVER_AUTHOR The missing NXTCam ID has been found at http://www.unixboard.de/vb3/showthread.php?t=44155 , ELV devices taken from ELV Windows .inf file. Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-02-16USB: ftdi_sio: new device id for papouch AD4USBRadek Liboska1-0/+1
added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c AD4USB measuring converter is a 4-input A/D converter which enables the user to measure to four current inputs ranging from 0(4) to 20 mA or voltage between 0 and 10 V. The measured values are then transferred to a superior system in digital form. The AD4USB communicates via USB. Powered is also via USB. datasheet in english is here: http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdf Signed-off-by: Radek Liboska <liboska@uochb.cas.cz>
2009-12-23USB: ftdi_sio: isolate all device IDs to new ftdi_sio_ids.h headerAndreas Mohr1-0/+1
This is a strictly move-only patch to relocate all FTDI device product ID definitions to their own ftdi_sio_ids.h header (following the usual *_ids.h kernel tree convention, too), thus correcting the slightly too messy appearance (crucial driver defines were stuck somewhere in the decaying middle swamp of the huge existing header). Compile-tested, based on latest mainline git. Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11USB: ftdi_sio: add USB device ID's for B&B Electronics lineCliff Brake1-0/+14
Reviewed-by: John Pilles <jpilles@bb-elec.com> Signed-off-by: Cliff Brake <cbrake@bec-systems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11USB: serial: ftdi_sio: add space/mark parityRoland Koebler1-6/+12
Add mark and space parity, since the device supports it. Signed-off-by: Roland Koebler <r.koebler@yahoo.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-11-30USB: ftdi_sio: Keep going when write errors are encountered.Eric W. Biederman1-2/+1
The use of urb->actual_length to update tx_outstanding_bytes implicitly assumes that the number of bytes actually written is the same as the number of bytes we tried to write. On error that assumption is violated so just use transfer_buffer_length the number of bytes we intended to write to the device. If an error occurs we need to fall through and call usb_serial_port_softint to wake up processes waiting in tty_wait_until_sent. Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-09USB: ftdi_sio: re-implement read processingJohan Hovold1-252/+131
- Re-structure read processing. - Kill obsolete work queue and always push to tty in completion handler. - Use tty_insert_flip_string instead of per character push when possible. - Fix stalled-read regression in 2.6.31 by using urb status to determine when port is closed rather than port count. - Fix race with open/close by checking ASYNCB_INITIALIZED in unthrottle. - Kill private rx_flag and lock and use throttle flags in usb_serial_port instead. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-09USB: ftdi_sio: clean up read completion handlerJohan Hovold1-27/+1
Remove superfluous error checks in completion handler: - No need to check private data and urb pointers as we check urb-status before dereferencing priv (which is not freed until urb has been killed on close). - No need to check tty as it is checked again when processing. - No need to check urb->number_of_packets on bulk urb. Note that both private data and tty are checked again before processing (possibly from work queue which also is cancelled on close). Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-09USB: ftdi_sio: remove unused rx_byte counterJohan Hovold1-13/+0
Remove unused rx_byte counter which is never exposed as noted by Alan Cox. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-09USB: ftdi_sio: remove tty->low_latencyJohan Hovold1-4/+0
Fixes tty_flip_buffer_push being called from hard interrupt context with low_latency set. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-23USB: serial: ftdi: handle gnICE+ JTAG adaptorsMichael Hennerich1-0/+2
Detect the UART on interface1 and blacklist interface0 (as that is the JTAG port). Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-23USB: add PIDs for FTDI based OpenDCC hardwaremail@rainerkeller.de1-0/+3
Some devices from the OpenDCC project are missing in the list of the FTDI PIDs. These PIDs are listed at http://www.opendcc.de/elektronik/usb/opendcc_usb.html (Sorry for the german only page.) This patch adds the three missing devices. Signed-off-by: Rainer Keller <mail@rainerkeller.de> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-23USB: serial: ftdi_sio: new hardware support - hameg power supplyPawel Ludwikow1-0/+2
I'd like to present my small patch enabling to use Hameg HM8143 programmable power supply with linux. Signed-off-by: Pawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19tty: USB does not need the filp argument in the driversAlan Cox1-4/+2
And indeed none of them use it. Clean this up as it will make moving to a standard open method rather easier. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-08-07USB: ftdi_sio: add product_id for Marvell OpenRD Base, ClientDhaval Vasa1-0/+2
reference: http://www.open-rd.org Signed-off-by: Dhaval Vasa <dhaval.vasa@einfochips.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-08-07USB: ftdi_sio: add vendor and product id for Bayer glucose meter serial ↵Marko Hänninen1-0/+1
converter cable Attached patch adds USB vendor and product IDs for Bayer's USB to serial converter cable used by Bayer blood glucose meters. It seems to be a FT232RL based device and works without any problem with ftdi_sio driver when this patch is applied. See: http://winglucofacts.com/cables/ Signed-off-by: Marko Hänninen <bugitus@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-28USB: ftdi_sio: Add support for GN Otometrics Aurical USB AudiometerVille Sundberg1-0/+1
The patch adds support for the GN Otometrics Aurical USB Audiometer (FT232BM-based). A new VID and a new PID is added. Signed-off-by: Ville Sundberg <vsundber@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds1-1/+66
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (48 commits) USB: otg: fix module reinsert issue USB: handle zero-length usbfs submissions correctly USB: EHCI: report actual_length for iso transfers USB: option: remove unnecessary and erroneous code USB: cypress_m8: remove invalid Clear-Halt USB: musb_host: undo incorrect change in musb_advance_schedule() USB: fix LANGID=0 regression USB: serial: sierra driver id_table additions USB serial: Add ID for Turtelizer, an FT2232L-based JTAG/RS-232 adapter. USB: fix race leading to a write after kfree in usbfs USB: Sierra: fix oops upon device close USB: option.c: add A-Link 3GU device id USB: Serial: Add support for Arkham Technology adapters USB: Fix option_ms regression in 2.6.31-rc2 USB: gadget audio: select SND_PCM USB: ftdi: support NDI devices Revert USB: usbfs: deprecate and hide option for !embedded USB: usb.h: fix kernel-doc notation USB: RNDIS gadget, fix issues talking from PXA USB: serial: FTDI with product code FB80 and vendor id 0403 ...
2009-07-12USB serial: Add ID for Turtelizer, an FT2232L-based JTAG/RS-232 adapter.Krzysztof Halasa1-0/+2
Adds USB ID for Turtelizer, an FT2232L-based JTAG/RS-232 adapter. Signed-off-by: Krzysztof Ha³asa <khc@pm.waw.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-12USB: ftdi: support NDI devicesMartin Geleynse1-1/+60
It enhances the driver for FTDI-based USB serial adapters to recognize and support Northern Digital Inc (NDI) measurement equipment. NDI has been providing this patch for various kernel flavors for several years and we would like to see these changes built in to the driver so that our equipement works without the need for customers to patch the kernel themselves. The patch makes small modifications to 2 files: ./drivers/usb/serial/ftdi_sio.c and ./drivers/usb/serial/ftdi_sio.h. It accomplishes 3 things: 1. Define the VID and PIDs to allow the driver to recognize the NDI devices. 2. Map the 19200 baud rate setting to our higher baud rate of 1.2Mb We would have chosen to map 38400 to the higher rate, similar to what several other vendors have done, but some of our legacy customers actually use 38400, therefore we remap 19200 to the higher rate. 3. We set the default transmit latency in the FTDI chip to 1ms for our devices. Our devices are typically polled at 60Hz and the default ftdi latency seriously affects turn-around time and results in missed data frames. We have created a modprobe option that allows this setting to be increased. This has proven necessary particularly in some virtualized environments. Signed-off-by: Martin P. Geleynse <mgeleyns@ndigital.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-12USB: serial: FTDI with product code FB80 and vendor id 0403Folkert van Heusden1-0/+1
It seems an USB device with vendor id 0403 and product code FB80 has an FTDI serial io chip as well: http://ftdichip.com/Drivers/D2XX.htm This device in fact is a true random generantor by comsci: http://comscire.com/Products/R2000KU/ So the following patch should add support for this device if I am correct. Not tested as I do not own this device (I would like support in the kernel so that my entropybroker application (which distributes entrop data (random values) between servers and clients)). From: Folkert van Heusden <folkert@vanheusden.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-12USB: ftdi_sio - product ID's for CCS PIC programmersJan Capek1-0/+3
The product ID's for the following devices have been added: - LOAD-n-GO - ICD-U64 - PRIME-8 Signed-off-by: Jan Capek <jan@ccsinfo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-12headers: smp_lock.h reduxAlexey Dobriyan1-0/+1
* Remove smp_lock.h from files which don't need it (including some headers!) * Add smp_lock.h to files which do need it * Make smp_lock.h include conditional in hardirq.h It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT This will make hardirq.h inclusion cheaper for every PREEMPT=n config (which includes allmodconfig/allyesconfig, BTW) Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-10tty: Fix USB kref leakAlan Cox1-1/+1
The sysrq code acquired a kref leak. Fix it by passing the tty separately from the caller (thus effectively using the callers kref which all the callers hold anyway) Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-15USB: usb-serial: replace shutdown with disconnect, releaseAlan Stern1-14/+0
This patch (as1254) splits up the shutdown method of usb_serial_driver into a disconnect and a release method. The problem is that the usb-serial core was calling shutdown during disconnect handling, but drivers didn't expect it to be called until after all the open file references had been closed. The result was an oops when the close method tried to use memory that had been deallocated by shutdown. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15USB: serial: ftd_sio: implement sysrq handling on breakJason Wessel1-2/+6
Change driver to make use of the new functions in include/linux/usb/serial.h so as to allow the driver to handle the sysrq Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15USB: serial: ftd_sio usb: move status checkJason Wessel1-5/+5
Alan Stern commented that the private driver counts must be updated regard less of the status return on the urb when the write call back is executed. This patch alters the behavior to update the private driver counts by simply moving the status check to after the driver count update. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15USB: ftdi_sio: fix hi-speed device packet size calculationMark Adamson1-8/+48
Added a function to set the packet size to be used based on the value from the device endpoint descriptor. The FT2232H and FT4232H hi-speed devices will have wMaxPacketSize of 512 bytes when connected to a USB 2.0 hi-speed host, but will use alternative descriptors with wMaxPacketSize of 64 bytes if connected to a USB 1.1 host or hub. All other FTDI devices have wMaxPacketSize of 64 bytes, except some FT232R and FT245R devices which customers have mistakenly programmed to have wMaxPacketSize of 0 - this is an error and will be overridden to use wMaxPacketSize of 64 bytes. The packet size used is important as it determines where the driver removes the status bytes from the incoming data. If it is incorrect, it will lead to data corruption. Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15USB: serial: FTDI: add high speed device supportMark Adamson1-10/+80
Added support for FTDI's USB 2.0 hi-speed devices - FT2232H (2 interfaces) and FT4232H (4 interfaces), including a new baud rate calculation for these devices which can now achieve up to 12Mbaud by turning off a divide by 2.5 in the baud rate generator of the chips. In order to achieve baud rates of <1200 baud, the divide by 2.5 must be active. The default product ID of the FT2232H is 0x6010 (same as the FT2232C IC). The default PID of the FT4232H is 0x6011. Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15USB: FTDI-SIO new device idsDaniel Suchy1-0/+1
I would like to have added new device to usbserial/ftdi_sio driver. These ids used USB track device (http://www.l-and-b.dk/access_alt.html). They use differend device IDs, but it works as standard usb-serial conventer. From: Daniel Suchy <danny@danysek.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-11ftdi_sio: don't override modem bitsAlan Cox1-5/+0
The new open/close logic handles DTR and friends, so don't do it in our own open routine as well. Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-11ft232: support the ASYNC_LOW_LATENCY flagAlan Cox1-34/+60
This allows users to use the standard setserial command with this FT232 feature as well as obscure chip specific interfaces we have now. We keep track of and respect the sysfs value for non-low-latency cases. In theory we could do smart stuff with VTIME and the like but this seems of questionable worth. Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=9120 Signed-off-by: Alan Cox <alan@linux.intel.com) Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-11tty: Bring the usb tty port structure into more useAlan Cox1-22/+28
This allows us to clean stuff up, but is probably also going to cause some app breakage with buggy apps as we now implement proper POSIX behaviour for USB ports matching all the other ports. This does also mean other apps that break on USB will now work properly. Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-05-18Fix oops on close of hot-unplugged FTDI serial converterDavid Woodhouse1-8/+1
Commit c45d6320 ("fix reference counting of ftdi_private") stopped ftdi_sio_port_remove() from directly freeing the port-private data, with the intention if the port was still open, it would be freed when ftdi_close() is eventually called and releases the last refcount on the structure. That's all very well, but ftdi_sio_port_remove() still contains a call to usb_set_serial_port_data(port, NULL) -- so by the time we get to ftdi_close() for the port which was unplugged, it _still_ oopses on dereferencing that NULL pointer, as it did before (and does in 2.6.29). The fix is just not to clear the private data in ftdi_sio_port_remove(). Then the refcount is properly reduced to zero when the final kref_put() happens in ftdi_close(). Remove a bogus comment too, while we're at it. And stop doing things inside "if (priv)" -- it must _always_ be there. Based loosely on an earlier patch by Daniel Mack, and suggestions by Alan Stern. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Tested-by: Daniel Mack <daniel@caiaq.de> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-05-08usb-serial: ftdi_sio: fix reference counting of ftdi_privateAlan Stern1-4/+14
This patch (as1238) adds proper reference counting for ftdi_sio's private data structure. Without it, the driver will free the structure while it is still in use if the user unplugs the serial device before closing the device file. The patch also replaces a slightly dangerous cancel_delayed_work/flush_scheduled_work pair with cancel_delayed_work_sync, which is always safer. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Daniel Mack <daniel@caiaq.de> Tested-by: Daniel Mack <daniel@caiaq.de> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-05-08USB: ftdi_sio: add vendor/product id for the Marvell SheevaPlugNicolas Pitre1-0/+2
For reference: http://www.marvell.com/products/embedded_processors/developer/kirkwood/sheevaplug.jsp Signed-off-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-17USB: ftdi_sio: add vendor/project id for JETI specbos 1201 spectrometerPeter Korsgaard1-0/+1
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: make actual_length in struct urb field u32Greg Kroah-Hartman1-1/+1
actual_length should also be a u32 and not a signed value. This patch changes this field to be 'u32' to prevent any potential negative conversion and comparison errors. This triggered a few compiler warning messages when these fields were being used with the min macro, so they have also been fixed up in this patch. Cc: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: ftdi_sio: remove pointless syslog spewDavid Brownell1-9/+2
Remove some pointless messages from the FTDI serial driver; I found these filling up syslog on one system. Also remove a pointless "break" after a "return" in the same area. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24USB: Remove redundant test in pxa27x_udc and ftdi_sioJulia Lawall1-9/+7
priv is checked not to be NULL near the beginning of the function and not changed subsequently, making the test redundant. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; expression E; position p1,p2; @@ if (x@p1 == NULL || ...) { ... when forall return ...; } ... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\) ( x@p2 == NULL | x@p2 != NULL ) // another path to the test that is not through p1? @s exists@ local idexpression r.x; position r.p1,r.p2; @@ ... when != x@p1 ( x@p2 == NULL | x@p2 != NULL ) @fix depends on !s@ position r.p1,r.p2; expression x,E; statement S1,S2; @@ ( - if ((x@p2 != NULL) || ...) S1 | - if ((x@p2 == NULL) && ...) S1 | - BUG_ON(x@p2 == NULL); ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17USB: serial: ftdi: enable UART detection on gnICE JTAG adaptors blacklist ↵Michael Hennerich1-0/+2
interface0 Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.39.1) at 2025-04-11 18:06:02 +0000