summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host/xhci-hub.c
AgeCommit message (Collapse)AuthorFilesLines
2022-05-12xhci: prepare for operation w/o shared hcdHeiner Kallweit1-1/+2
This patch prepares xhci for the following scenario: - If either of the root hubs has no ports, then omit shared hcd - Main hcd can be USB3 if there are no USB2 ports Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220511220450.85367-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-09xhci: increase usb U3 -> U0 link resume timeout from 100ms to 500msMathias Nyman1-1/+1
The first U3 wake signal by the host may be lost if the USB 3 connection is tunneled over USB4, with a runtime suspended USB4 host, and firmware implemented connection manager. Specs state the host must wait 100ms (tU3WakeupRetryDelay) before resending a U3 wake signal if device doesn't respond, leading to U3 -> U0 link transition times around 270ms in the tunneled case. Fixes: 0200b9f790b0 ("xhci: Wait until link state trainsits to U0 after setting USB_SS_PORT_LS_U0") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220408134823.2527272-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-03xhci: fix runtime PM imbalance in USB2 resumeHenry Lin1-0/+3
A race between system resume and device-initiated resume may result in runtime PM imbalance on USB2 root hub. If a device-initiated resume starts and system resume xhci_bus_resume() directs U0 before hub driver sees the resuming device in RESUME state, device-initiated resume will not be finished in xhci_handle_usb2_port_link_resume(). In this case, usb_hcd_end_port_resume() call is missing. This changes calls usb_hcd_end_port_resume() if resuming device reaches U0 to keep runtime PM balance. Fixes: a231ec41e6f6 ("xhci: refactor U0 link state handling in get_port_status") Cc: stable@vger.kernel.org Signed-off-by: Henry Lin <henryl@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220303110903.1662404-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-03xhci: make xhci_handshake timeout for xhci_reset() adjustableMathias Nyman1-1/+1
xhci_reset() timeout was increased from 250ms to 10 seconds in order to give Renesas 720201 xHC enough time to get ready in probe. xhci_reset() is called with interrupts disabled in other places, and waiting for 10 seconds there is not acceptable. Add a timeout parameter to xhci_reset(), and adjust it back to 250ms when called from xhci_stop() or xhci_shutdown() where interrupts are disabled, and successful reset isn't that critical. This solves issues when deactivating host mode on platforms like SM8450. For now don't change the timeout if xHC is reset in xhci_resume(). No issues are reported for it, and we need the reset to succeed. Locking around that reset needs to be revisited later. Additionally change the signed integer timeout parameter in xhci_handshake() to a u64 to match the timeout value we pass to readl_poll_timeout_atomic() Fixes: 22ceac191211 ("xhci: Increase reset timeout for Renesas 720201 host.") Cc: stable@vger.kernel.org Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com> Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-10xhci: avoid race between disable slot command and host runtime suspendMathias Nyman1-0/+1
Make xhci_disable_slot() synchronous, thus ensuring it, and xhci_free_dev() calling it return after xHC controller completes the disable slot command. Otherwise the roothub and xHC host may runtime suspend, and clear the command ring while the disable slot command is being processed. This causes a command completion mismatch as the completion event can't be mapped to the correct command. Command ring gets out of sync and commands time out. Driver finally assumes host is unresponsive and bails out. usb 2-4: USB disconnect, device number 10 xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event ... xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead xhci_hcd 0000:00:0d.0: HC died; cleaning up Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-06xhci: Fix USB 3.1 enumeration issues by increasing roothub power-on-good delayMathias Nyman1-1/+2
Some USB 3.1 enumeration issues were reported after the hub driver removed the minimum 100ms limit for the power-on-good delay. Since commit 90d28fb53d4a ("usb: core: reduce power-on-good delay time of root hub") the hub driver sets the power-on-delay based on the bPwrOn2PwrGood value in the hub descriptor. xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based on xhci spec section 5.4.8, but it's clearly not enough for the USB 3.1 devices, causing enumeration issues. Tests indicate full 100ms delay is needed. Reported-by: Walt Jr. Brake <mr.yming81@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: 90d28fb53d4a ("usb: core: reduce power-on-good delay time of root hub") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-08-26xhci: Add bus number to some debug messagesMathias Nyman1-2/+4
As we register two usb buses for each xHC, and systems with several hosts are more and more common it is getting hard to follow the flow of debug messages without knowing which bus they belong to Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210820123503.2605901-7-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-21xhci: Fix lost USB 2 remote wakeMathias Nyman1-1/+2
There's a small window where a USB 2 remote wake may be left unhandled due to a race between hub thread and xhci port event interrupt handler. When the resume event is detected in the xhci interrupt handler it kicks the hub timer, which should move the port from resume to U0 once resume has been signalled for long enough. To keep the hub "thread" running we set a bus_state->resuming_ports flag. This flag makes sure hub timer function kicks itself. checking this flag was not properly protected by the spinlock. Flag was copied to a local variable before lock was taken. The local variable was then checked later with spinlock held. If interrupt is handled right after copying the flag to the local variable we end up stopping the hub thread before it can handle the USB 2 resume. CPU0 CPU1 (hub thread) (xhci event handler) xhci_hub_status_data() status = bus_state->resuming_ports; <Interrupt> handle_port_status() spin_lock() bus_state->resuming_ports = 1 set_flag(HCD_FLAG_POLL_RH) spin_unlock() spin_lock() if (!status) clear_flag(HCD_FLAG_POLL_RH) spin_unlock() Fix this by taking the lock a bit earlier so that it covers the resuming_ports flag copy in the hub thread Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-23usb: xhci: Remove unused functionThinh Nguyen1-147/+0
Now that we replaced the xhci_create_usb3_bos_desc() function. We can remove it along with the static usb_bos_descriptor structure. Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/ce0acbbd0bd3c3c3a08e6418ab3bdb431a44bbfd.1615432770.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-03-23usb: xhci: Rewrite xhci_create_usb3_bos_desc()Thinh Nguyen1-2/+235
The current xhci_create_usb3_bos_desc() uses a static bos u8 array and various magic numbers and offsets making it difficult to extend support for USB 3.2. Let's rewrite this entire function to support dual-lane in USB 3.2. The hub driver matches the port speed ID from the extended port status to the SSID of the sublink speed attributes to detect if the device supports SuperSpeed Plus. Currently we don't provide the default gen1x2 and gen2x2 sublink speed capability descriptor for USB 3.2 roothub. The USB stack depends on this to detect and match the correct speed. In addition, if the xHCI host provides Protocol Speed ID (PSI) capability, then make sure to convert Protocol Speed ID Mantissa and Exponent (PSIM & PSIE) to lane speed for gen1x2 and gen2x2. Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/19cd09b03f96346996270579fd27d38b8a6844aa.1615432770.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-12-09xhci: Give USB2 ports time to enter U3 in bus suspendLi Jun1-0/+4
If a USB2 device wakeup is not enabled/supported the link state may still be in U0 in xhci_bus_suspend(), where it's then manually put to suspended U3 state. Just as with selective suspend the device needs time to enter U3 suspend before continuing with further suspend operations (e.g. system suspend), otherwise we may enter system suspend with link state in U0. [commit message rewording -Mathias] Cc: <stable@vger.kernel.org> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20201208092912.1773650-6-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-30Merge tag 'usb-5.9-rc3' of ↵Linus Torvalds1-9/+10
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Let's try this again... Here are some USB fixes for 5.9-rc3. This differs from the previous pull request for this release in that the usb gadget patch now does not break some systems, and actually does what it was intended to do. Many thanks to Marek Szyprowski for quickly noticing and testing the patch from Andy Shevchenko to resolve this issue. Additionally, some more new USB quirks have been added to get some new devices to work properly based on user reports. Other than that, the patches are all here, and they contain: - usb gadget driver fixes - xhci driver fixes - typec fixes - new quirks and ids - fixes for USB patches that went into 5.9-rc1. All of these have been tested in linux-next with no reported issues" * tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits) usb: storage: Add unusual_uas entry for Sony PSZ drives USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe() USB: gadget: u_f: Unbreak offset calculation in VLAs USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures USB: PHY: JZ4770: Fix static checker warning. USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb() USB: gadget: u_f: add overflow checks to VLA macros xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed xhci: Do warm-reset when both CAS and XDEV_RESUME are set usb: host: xhci: fix ep context print mismatch in debugfs usb: uas: Add quirk for PNY Pro Elite tools: usb: move to tools buildsystem USB: Fix device driver race USB: Also match device drivers using the ->match vfunc usb: host: xhci-tegra: fix tegra_xusb_get_phy() usb: host: xhci-tegra: otg usb2/usb3 port init usb: hcd: Fix use after free in usb_hcd_pci_remove() usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port() ...
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva1-1/+1
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-23xhci: Do warm-reset when both CAS and XDEV_RESUME are setKai-Heng Feng1-9/+10
Sometimes re-plugging a USB device during system sleep renders the device useless: [ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262 ... [ 176.496485] usb 2-4: Waited 2000ms for CONNECT [ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19 [ 176.497103] usb 2-4: can't resume, status -19 [ 176.497438] usb usb2-port4: logical disconnect Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore, despite of CAS bit is flagged. So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for the port. Cc: stable <stable@vger.kernel.org> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-23xhci: Make debug message consistent with bus and port numberKai-Heng Feng1-18/+23
Current xhci debug message doesn't always output bus number, so it's hard to figure out it's from USB2 or USB3 root hub. In addition to that, some port numbers are offset to 0 and others are offset to 1. Use the latter to match the USB core. So use "bus number - port index + 1" to make debug message consistent. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200723144530.9992-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-24USB: ch9: add "USB_" prefix in front of TEST definesGreg Kroah-Hartman1-3/+4
For some reason, the TEST_ defines in the usb/ch9.h files did not have the USB_ prefix on it, making it a bit confusing when reading the file, as well as not the nicest thing to do in a uapi file. So fix that up and add the USB_ prefix on to them, and fix up all in-kernel usages. This included deleting the duplicate copy in the net2272.h file. Cc: Felipe Balbi <balbi@kernel.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Mathias Nyman <mathias.nyman@intel.com> Cc: Pawel Laszczak <pawell@cadence.com> Cc: YueHaibing <yuehaibing@huawei.com> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Jason Yan <yanaijie@huawei.com> Cc: Jia-Ju Bai <baijiaju1990@gmail.com> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jules Irenge <jbi.octave@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Cc: Rob Gill <rrobgill@protonmail.com> Cc: Macpaul Lin <macpaul.lin@mediatek.com> Acked-by: Minas Harutyunyan <hminas@synopsys.com> Acked-by: Bin Liu <b-liu@ti.com> Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Acked-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20200618144206.2655890-1-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-04-21xhci: prevent bus suspend if a roothub port detected a over-current conditionMathias Nyman1-0/+9
Suspending the bus and host controller while a port is in a over-current condition may halt the host. Also keep the roothub running if over-current is active. Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200421140822.28233-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12xhci: Finetune host initiated USB3 rootport link suspend and resumeMathias Nyman1-11/+25
Depending on the current link state the steps to resume the link to U0 varies. The normal case when a port is suspended (U3) we set the link to U0 and wait for a port event when U3exit completed and port moved to U0. If the port is in U1/U2, then no event is issued, just set link to U0 If port is in Resume or Recovery state then the device has already initiated resume, and this host initiated resume is racing against it. Port event handler for device initiated resume will set link to U0, just wait for the port to reach U0 before returning. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200312144517.1593-9-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12xhci: Wait until link state trainsits to U0 after setting USB_SS_PORT_LS_U0Kai-Heng Feng1-13/+31
Like U3 case, xHCI spec doesn't specify the upper bound of U0 transition time. The 20ms is not enough for some devices. Intead of polling PLS or PLC, we can facilitate the port change event to know that the link transits to U0 is completed. While at it, also separate U0 and U3 case to make the code cleaner. [variable rename to u3exit, and skip completion for usb2 ports -Mathias ] Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200312144517.1593-8-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12xhci: Ensure link state is U3 after setting USB_SS_PORT_LS_U3Kai-Heng Feng1-1/+10
The xHCI spec doesn't specify the upper bound of U3 transition time. For some devices 20ms is not enough, so we need to make sure the link state is in U3 before further actions. I've tried to use U3 Entry Capability by setting U3 Entry Enable in config register, however the port change event for U3 transition interrupts the system suspend process. For now let's use the less ideal method by polling PLS. [use usleep_range(), and shorten the delay time while polling -Mathias] Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200312144517.1593-7-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-24Merge 5.6-rc3 into usb-nextGreg Kroah-Hartman1-8/+17
We need the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-17xhci: Add missing annotation for xhci_enter_test_modeJules Irenge1-0/+1
Sparse reports a warning at xhci_enter_test_mode() warning: context imbalance in xhci_enter_test_mode - unexpected unlock The root cause is the missing annotation at xhci_enter_test_mode() Add the missing __must_hold(&xhci->lock) annotattion Signed-off-by: Jules Irenge <jbi.octave@gmail.com> Link: https://lore.kernel.org/r/20200214204741.94112-24-jbi.octave@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-17xhci: Add missing annotation for xhci_set_port_power()Jules Irenge1-0/+1
Sparse reports a warning at xhci_set_port_power() warning: context imbalance in xhci_set_port_power - unexpected unlock The root cause is the missing annotation at xhci_set_port_power() Add the missing __must_hold(&xhci->lock) annotattion Signed-off-by: Jules Irenge <jbi.octave@gmail.com> Link: https://lore.kernel.org/r/20200214204741.94112-23-jbi.octave@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12xhci: Fix memory leak when caching protocol extended capability PSI tables - ↵Mathias Nyman1-8/+17
take 2 xhci driver assumed that xHC controllers have at most one custom supported speed table (PSI) for all usb 3.x ports. Memory was allocated for one PSI table under the xhci hub structure. Turns out this is not the case, some controllers have a separate "supported protocol capability" entry with a PSI table for each port. This means each usb3 roothub port can in theory support different custom speeds. To solve this, cache all supported protocol capabilities with their PSI tables in an array, and add pointers to the xhci port structure so that every port points to its capability entry in the array. When creating the SuperSpeedPlus USB Device Capability BOS descriptor for the xhci USB 3.1 roothub we for now will use only data from the first USB 3.1 capable protocol capability entry in the array. This could be improved later, this patch focuses resolving the memory leak. Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com> Fixes: 47189098f8be ("xhci: parse xhci protocol speed ID list for usb 3.1 usage") Cc: stable <stable@vger.kernel.org> # v4.4+ Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20200211150158.14475-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12Revert "xhci: Fix memory leak when caching protocol extended capability PSI ↵Greg Kroah-Hartman1-17/+8
tables" This reverts commit fc57313d1017dd6b6f37a94e88daa8df54368ecc. Marek reports that it breaks things: This patch landed in today's linux-next (20200211) and causes NULL pointer dereference during second suspend/resume cycle on Samsung Exynos5422-based (arm 32bit) Odroid XU3lite board: A more complete fix will be added soon. Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: fc57313d1017 ("xhci: Fix memory leak when caching protocol extended capability PSI tables") Cc: Paul Menzel <pmenzel@molgen.mpg.de> Cc: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com> Cc: stable <stable@vger.kernel.org> # v4.4+ Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10xhci: Fix memory leak when caching protocol extended capability PSI tablesMathias Nyman1-8/+17
xhci driver assumed that xHC controllers have at most one custom supported speed table (PSI) for all usb 3.x ports. Memory was allocated for one PSI table under the xhci hub structure. Turns out this is not the case, some controllers have a separate "supported protocol capability" entry with a PSI table for each port. This means each usb3 roothub port can in theory support different custom speeds. To solve this, cache all supported protocol capabilities with their PSI tables in an array, and add pointers to the xhci port structure so that every port points to its capability entry in the array. When creating the SuperSpeedPlus USB Device Capability BOS descriptor for the xhci USB 3.1 roothub we for now will use only data from the first USB 3.1 capable protocol capability entry in the array. This could be improved later, this patch focuses resolving the memory leak. Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com> Fixes: 47189098f8be ("xhci: parse xhci protocol speed ID list for usb 3.1 usage") Cc: stable <stable@vger.kernel.org> # v4.4+ Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200210134553.9144-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-11xhci: make sure interrupts are restored to correct stateMathias Nyman1-6/+6
spin_unlock_irqrestore() might be called with stale flags after reading port status, possibly restoring interrupts to a incorrect state. If a usb2 port just finished resuming while the port status is read the spin lock will be temporary released and re-acquired in a separate function. The flags parameter is passed as value instead of a pointer, not updating flags properly before the final spin_unlock_irqrestore() is called. Cc: <stable@vger.kernel.org> # v3.12+ Fixes: 8b3d45705e54 ("usb: Fix xHCI host issues on remote wakeup.") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-11xhci: fix USB3 device initiated resume race with roothub autosuspendMathias Nyman1-0/+10
A race in xhci USB3 remote wake handling may force device back to suspend after it initiated resume siganaling, causing a missed resume event or warm reset of device. When a USB3 link completes resume signaling and goes to enabled (UO) state a interrupt is issued and the interrupt handler will clear the bus_state->port_remote_wakeup resume flag, allowing bus suspend. If the USB3 roothub thread just finished reading port status before the interrupt, finding ports still in suspended (U3) state, but hasn't yet started suspending the hub, then the xhci interrupt handler will clear the flag that prevented roothub suspend and allow bus to suspend, forcing all port links back to suspended (U3) state. Example case: usb_runtime_suspend() # because all ports still show suspended U3 usb_suspend_both() hub_suspend(); # successful as hub->wakeup_bits not set yet ==> INTERRUPT xhci_irq() handle_port_status() clear bus_state->port_remote_wakeup usb_wakeup_notification() sets hub->wakeup_bits; kick_hub_wq() <== END INTERRUPT hcd_bus_suspend() xhci_bus_suspend() # success as port_remote_wakeup bits cleared Fix this by increasing roothub usage count during port resume to prevent roothub autosuspend, and by making sure bus_state->port_remote_wakeup flag is only cleared after resume completion is visible, i.e. after xhci roothub returned U0 or other non-U3 link state link on a get port status request. Issue rootcaused by Chiasheng Lee Cc: <stable@vger.kernel.org> Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com> Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-25usb: host: xhci-hub: fix extra endianness conversionRuslan Bilovol1-1/+1
Don't do extra cpu_to_le32 conversion for put_unaligned_le32 because it is already implemented in this function. Fixes sparse error: xhci-hub.c:1152:44: warning: incorrect type in argument 1 (different base types) xhci-hub.c:1152:44: expected unsigned int [usertype] val xhci-hub.c:1152:44: got restricted __le32 [usertype] Fixes: 395f540 "xhci: support new USB 3.1 hub request to get extended port status" Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Link: https://lore.kernel.org/r/1562501839-26522-1-git-send-email-ruslan.bilovol@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27xhci: add port and bus number to port dynamic debuggingMathias Nyman1-17/+27
Improve port related dynamic debugging by printing out the bus number, port number and port status register content each time there is a port related debug messages. Use the same port numbering method as usbcore to simplify debugging. i.e. starting with port number 1. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-22xhci: Don't let USB3 ports stuck in polling state prevent suspendMathias Nyman1-7/+12
Commit 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") was intended to prevent ports that were still link training from being forced to U3 suspend state mid enumeration. This solved enumeration issues for devices with slow link training. Turns out some devices are stuck in the link training/polling state, and thus that patch will prevent suspend completely for these devices. This is seen with USB3 card readers in some MacBooks. Instead of preventing suspend, give some time to complete the link training. On successful training the port will end up as connected and enabled. If port instead is stuck in link training the bus suspend will continue suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout). Original patch was sent to stable, this one should go there as well Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-21Merge USB 4.20-rc8 mergepoint into usb-nextGreg Kroah-Hartman1-1/+2
We need the USB changes in here for additional patches to be able to apply cleanly. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-14xhci: Don't prevent USB2 bus suspend in state check intended for USB3 onlyMathias Nyman1-1/+2
The code to prevent a bus suspend if a USB3 port was still in link training also reacted to USB2 port polling state. This caused bus suspend to busyloop in some cases. USB2 polling state is different from USB3, and should not prevent bus suspend. Limit the USB3 link training state check to USB3 root hub ports only. The origial commit went to stable so this need to be applied there as well Fixes: 2f31a67f01a8 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected") Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: move usb2 get port status link resume handling to its own functionMathias Nyman1-84/+104
Refactoring, no functional changes. But worth mentioning that checking for port link resume state is now behind a additional port power check. This is fine as ports can't be in resume state if port power bit is not set. xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume, and RExit states. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: refactor U0 link state handling in get_port_statusMathias Nyman1-13/+19
Move U0 link state handing to USB3 and USB2 specific functions Note that bus_state->resuming_ports: bus_state->resume_done[]: are only used for USB2, and don't need to cleared for USB3 ports No functional changes Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: cleanup code that sets portstatus and portchange bitsMathias Nyman1-12/+14
Group the code where the wPortstatus and wPortChange bits are set into one place. No functional changes Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: move usb2 speficic bits to own function in get_port_status callMathias Nyman1-20/+24
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state is reported if xhci port link is in U2 AND port is powered. Previously we did not check if the port was powered, but according to xhci spec 4.19.1.1.6 All the 'Enabled' states, including USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: move usb3 speficic bits to own function in get_port_status callMathias Nyman1-28/+40
refactoring, no functional changes Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-07xhci: move bus_state structure under the xhci_hub structure.Mathias Nyman1-9/+6
Move the bus_state structure under struct usb_hub. We need a bus_state strucure for each roothub to keep track of suspend related info for each port. Instead of keeping an array of two bus_state structures right under struct xhci, it makes more sense move them to the xhci_hub structure. No functional changes. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-15usb: xhci: Prevent bus suspend if a port connect change or polling state is ↵Mathias Nyman1-14/+46
detected USB3 roothub might autosuspend before a plugged USB3 device is detected, causing USB3 device enumeration failure. USB3 devices don't show up as connected and enabled until USB3 link trainig completes. On a fast booting platform with a slow USB3 link training the link might reach the connected enabled state just as the bus is suspending. If this device is discovered first time by the xhci_bus_suspend() routine it will be put to U3 suspended state like the other ports which failed to suspend earlier. The hub thread will notice the connect change and resume the bus, moving the port back to U0 This U0 -> U3 -> U0 transition right after being connected seems to be too much for some devices, causing them to first go to SS.Inactive state, and finally end up stuck in a polling state with reset asserted Fix this by failing the bus suspend if a port has a connect change or is in a polling state in xhci_bus_suspend(). Don't do any port changes until all ports are checked, buffer all port changes and only write them in the end if suspend can proceed Cc: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-09usb: xhci: fix timeout for transition from RExit to U0Aaron Ma1-2/+2
This definition is used by msecs_to_jiffies in milliseconds. According to the comments, max rexit timeout should be 20ms. Align with the comments to properly calculate the delay. Verified on Sunrise Point-LP and Cannon Lake. Cc: stable@vger.kernel.org Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-09usb: xhci: fix uninitialized completion when USB3 port got wrong statusAaron Ma1-1/+1
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3, after clear port reset it works fine. Since this device is registered on USB3 roothub at boot, when port status reports not superspeed, xhci_get_port_status will call an uninitialized completion in bus_state[0]. Kernel will hang because of NULL pointer. Restrict the USB2 resume status check in USB2 roothub to fix hang issue. Cc: stable@vger.kernel.org Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-28xhci: Avoid USB autosuspend when resuming USB2 ports.Anshuman Gupta1-0/+5
When USB bus host controller root hub resumes from autosuspend, it immediately tries to enter auto-suspend, but there can be a scenario when root hub is resuming its usb2 ports, in that particular case USB host controller auto suspend fails since it is busy to resuming its usb2 ports. This makes multiple failed cycles of auto-suspend until all usb2 ports of host controller root hub do not resume. This patch uses USB core framework usb_hcd_start_port_resume, usb_hcd_end_port_resume API's in order to autoresume/autosuspend root hub properly. Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-25USB: xhci-hcd: Add get_resuming_ports methodAlan Stern1-0/+11
This patch adds support for the new get_resuming_ports HCD method to the xhci-hcd driver. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-24xhci: xhci-hub: use port structure members instead of xhci_get_ports()Mathias Nyman1-24/+4
xhci_get_ports() is one of the last functions using port_arrays in xhci-hub.c. We get the same data directly from hub and port structures instead, so convert and remove both xhci_get_ports() and port_arrays from all function that no longer need it. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-24xhci: change xhci_test_and_clear_bit() to use new port structureMathias Nyman1-12/+10
Don't use pointers to port array and port index as function parameters in xhci_test_and_clear_bit(), just use a pointer to the right port structure. xhci_test_and_clear_bit() was the last port_array user in xhci_get_port_status() and handle_port_status(), so remove the port_array from them as well. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-24xhci: change xhci_set_link_state() to work with port structuresMathias Nyman1-18/+16
Remove old iomem port array and index as parameters, just send a ponter to a port strucure instread Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-24xhci: xhci-hub: use new port structures for cas and wake mask functions.Mathias Nyman1-11/+10
Use port structures instead of mmio port arrays for xhci_port_missing_cas_quirk() and xhci_set_remote_wake_mask() in xhci-hub.c Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-24xhci: xhci-hub: use new port structures to get port address instead of port ↵Mathias Nyman1-62/+78
array Use the new port structures for functions in xhci-hub.c to get port mmio address of portsc register instead of the port array xhci_get_port_io_addr() is no longer needeed and is removed. Plan is to get rid of the mmio port array completely. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-24xhci: Add helper to get xhci roothub from hcdMathias Nyman1-0/+9
quick way to get the xhci roothub and thus all the ports belonging to a certain hcd Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-17 02:03:56 +0000