| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
A recent commit added an invalid RST expression to a kerneldoc comment
in hub.c. The fix is trivial.
Fixes: 9c6d778800b9 ("USB: core: Prevent nested device-reset calls")
Cc: <stable@vger.kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YxDDcsLtRZ7c20pq@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Automatic kernel fuzzing revealed a recursive locking violation in
usb-storage:
============================================
WARNING: possible recursive locking detected
5.18.0 #3 Not tainted
--------------------------------------------
kworker/1:3/1205 is trying to acquire lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
but task is already holding lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
...
stack backtrace:
CPU: 1 PID: 1205 Comm: kworker/1:3 Not tainted 5.18.0 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2988 [inline]
check_deadlock kernel/locking/lockdep.c:3031 [inline]
validate_chain kernel/locking/lockdep.c:3816 [inline]
__lock_acquire.cold+0x152/0x3ca kernel/locking/lockdep.c:5053
lock_acquire kernel/locking/lockdep.c:5665 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5630
__mutex_lock_common kernel/locking/mutex.c:603 [inline]
__mutex_lock+0x14f/0x1610 kernel/locking/mutex.c:747
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
usb_reset_device+0x37d/0x9a0 drivers/usb/core/hub.c:6109
r871xu_dev_remove+0x21a/0x270 drivers/staging/rtl8712/usb_intf.c:622
usb_unbind_interface+0x1bd/0x890 drivers/usb/core/driver.c:458
device_remove drivers/base/dd.c:545 [inline]
device_remove+0x11f/0x170 drivers/base/dd.c:537
__device_release_driver drivers/base/dd.c:1222 [inline]
device_release_driver_internal+0x1a7/0x2f0 drivers/base/dd.c:1248
usb_driver_release_interface+0x102/0x180 drivers/usb/core/driver.c:627
usb_forced_unbind_intf+0x4d/0xa0 drivers/usb/core/driver.c:1118
usb_reset_device+0x39b/0x9a0 drivers/usb/core/hub.c:6114
This turned out not to be an error in usb-storage but rather a nested
device reset attempt. That is, as the rtl8712 driver was being
unbound from a composite device in preparation for an unrelated USB
reset (that driver does not have pre_reset or post_reset callbacks),
its ->remove routine called usb_reset_device() -- thus nesting one
reset call within another.
Performing a reset as part of disconnect processing is a questionable
practice at best. However, the bug report points out that the USB
core does not have any protection against nested resets. Adding a
reset_in_progress flag and testing it will prevent such errors in the
future.
Link: https://lore.kernel.org/all/CAB7eexKUpvX-JNiLzhXBDWgfg2T9e9_0Tw4HQ6keN==voRbP0g@mail.gmail.com/
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rondreis <linhaoguo86@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkflDxvg0KWqyZK@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Call onboard_hub_create/destroy_pdevs() from hub_probe/disconnect()
to create/destroy platform devices for onboard USB hubs that may be
connected to the hub. The onboard hubs must have nodes in the
device tree.
onboard_hub_create/destroy_pdevs() are NOPs unless
CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct usb_hub to keep track of the onboard hub
platform devices that are owned by the hub.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220630123445.v24.4.Ic9dd36078f9d803de82ca01a6700c58b8e4de27e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The host needs to tell the device the exit latencies using the SET_SEL
request before device initiated link powermanagement can be enabled.
The exit latency values do not change after enumeration, it's enough
to set them once. So do like Windows 10 and issue the SET_SEL request
once just before setting the configuration.
This is also the sequence described in USB 3.2 specs "9.1.2 Bus
enumeration". SET_SEL is issued once before the Set Configuration
request, and won't be cleared by the Set Configuration,
Set Interface or ClearFeature (STALL) requests.
Only warm reset, hot reset, set Address 0 clears the exit latencies.
See USB 3.2 section 9.4.14 Table 9-10 Device parameters and events
Add udev->lpm_devinit_allow, and set it if SET_SEL was successful.
If not set, then don't try to enable device initiated LPM
We used to issue a SET_SEL request every time lpm is enabled for either
U1 or U2 link states, meaning a SET_SEL was issued twice after every
Set Configuration and Set Interface requests, easily accumulating to
over 15 SET_SEL requets during a USB3 webcam enumeration.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220506161807.3369439-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In some cases the port of an hub needs to be disabled or switched off
and on again. E.g. when the connected device needs to be re-enumerated.
Or it needs to be explicitly disabled while the rest of the usb tree
stays working.
For this purpose this patch adds an sysfs switch to enable/disable the
port on any hub. In the case the hub is supporting power switching, the
power line will be disabled to the connected device.
When the port gets disabled, the associated device gets disconnected and
removed from the logical usb tree. No further device will be enumerated
on that port until the port gets enabled again.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220607114522.3359148-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kasprintf() returns NULL or valid pointer. Since kfree() can handle
NULL pointer condition, simplify error and success paths in function
port_over_current_notify() by removing multiple error path labels.
Signed-off-by: Bhuvanesh Surachari <Bhuvanesh_Surachari@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/1652369834-4480-1-git-send-email-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Duncan Sands <duncan.sands@free.fr>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220317035514.6378-7-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Trying to disable Link Powermanagement (LPM) before port reset is
unnecessary and can cause additional delay if host can't communicate
with the device, which is often the reason why device is reset in the
first place.
usb_disable_lpm() will
- zero usb U1/U2 timeouts for the hub downstream port
- send ENABLE U1/U2 clear feature requests to the connected device.
- increase internal reference count for udev->lpm_disable_count
There is no need to zero U1/U2 hub port timeouts, or clearing the
U1/U2 enable for the connected device before reset. These are set
to default by the reset.
USB 3.1 section 10.2.2 "HUB Downstream port U1/U2 timers" states that:
"the U1 and U2 timeout values for a downstream port reset to the default
values when the port receives a SetPortFeature request for a port reset"
Set the udev->lpm_disable_count to "1" after port reset, which is the
default lpm_disable_count value when allocating udev, representing
disabled LPM.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unplugging USB device may cause an incorrect warm reset loop and the
port can no longer be used:
[ 143.039019] xhci_hcd 0000:00:14.0: Port change event, 2-3, id 19, portsc: 0x4202c0
[ 143.039025] xhci_hcd 0000:00:14.0: handle_port_status: starting usb2 port polling.
[ 143.039051] hub 2-0:1.0: state 7 ports 10 chg 0000 evt 0008
[ 143.039058] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x4202c0, return 0x4102c0
[ 143.039092] xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x4002c0
[ 143.039096] usb usb2-port3: link state change
[ 143.039099] xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
[ 143.039101] usb usb2-port3: do warm reset
[ 143.096736] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
[ 143.096751] usb usb2-port3: not warm reset yet, waiting 50ms
[ 143.131500] xhci_hcd 0000:00:14.0: Can't queue urb, port error, link inactive
[ 143.138260] xhci_hcd 0000:00:14.0: Port change event, 2-3, id 19, portsc: 0x2802a0
[ 143.138263] xhci_hcd 0000:00:14.0: handle_port_status: starting usb2 port polling.
[ 143.160756] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2802a0, return 0x3002a0
[ 143.160798] usb usb2-port3: not warm reset yet, waiting 200ms
The port status is PP=1, CCS=0, PED=0, PLS=Inactive, which is Error
state per "USB3 Root Hub Port State Machine". It's reasonable to perform
warm reset several times, but if the port is still not enabled after
many attempts, consider it's gone and treat it as disconnected.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220120070518.1643873-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports. (These hubs have other problems too. For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)
It turns out that the failures are caused by bugs in both the kernel
and the hub. The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).
The kernel's bug is inside the hub driver's resume handler. When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable. But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).
Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before. Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now). But with these dodgy hubs, the check
fails because the config descriptor has changed. This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits. That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected. This patch makes that change.
Cc: <stable@vger.kernel.org>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The wait_for_connected() function doesn't modify "*port1" and there is
no need to pass a pointer. Just pass the int itself.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211210142028.GB18906@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During disconnect USB-3 ports often go via SS.Inactive link error state
before the missing terminations are noticed, and link finally goes to
RxDetect state
Avoid immediately warm-resetting ports in SS.Inactive state.
Let ports settle for a while and re-read the link status a few times 20ms
apart to see if the ports transitions out of SS.Inactive.
According to USB 3.x spec 7.5.2, a port in SS.Inactive should
automatically check for missing far-end receiver termination every
12 ms (SSInactiveQuietTimeout)
The futile multiple warm reset retries of a disconnected device takes
a lot of time, also the resetting of a removed devices has caused cases
where the reset bit got stuck for a long time on xHCI roothub.
This lead to issues in detecting new devices connected to the same port
shortly after.
Tested-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210111653.1378381-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the circular lock dependency and unbalanced unlock of addess0_mutex
introduced when fixing an address0_mutex enumeration retry race in commit
ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Make sure locking order between port_dev->status_lock and address0_mutex
is correct, and that address0_mutex is not unlocked in hub_port_connect
"done:" codepath which may be reached without locking address0_mutex
Fixes: 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Cc: <stable@vger.kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211123101656.1113518-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org>
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Maximum Exit Latency (MEL) value is used by host to know how much in
advance it needs to start waking up a U1/U2 suspended link in order to
service a periodic transfer in time.
Current MEL calculation only includes the time to wake up the path from
U1/U2 to U0. This is called tMEL1 in USB 3.1 section C 1.5.2
Total MEL = tMEL1 + tMEL2 +tMEL3 + tMEL4 which should additinally include:
- tMEL2 which is the time it takes for PING message to reach device
- tMEL3 time for device to process the PING and submit a PING_RESPONSE
- tMEL4 time for PING_RESPONSE to traverse back upstream to host.
Add the missing tMEL2, tMEL3 and tMEL4 to MEL calculation.
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150122.1995966-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d758 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the "removable" attribute from USB to core in order to allow it to be
supported by other subsystem / buses. Individual buses that want to support
this attribute can populate the removable property of the device while
enumerating it with the 3 possible values -
- "unknown"
- "fixed"
- "removable"
Leaving the field unchanged (i.e. "not supported") would mean that the
attribute would not show up in sysfs for that device. The UAPI (location,
symantics etc) for the attribute remains unchanged.
Move the "removable" attribute from USB to the device core so it can be
used by other subsystems / buses.
By default, devices do not have a "removable" attribute in sysfs.
If a subsystem or bus driver wants to support a "removable" attribute, it
should call device_set_removable() before calling device_register() or
device_add(), e.g.:
device_set_removable(dev, DEVICE_REMOVABLE);
device_register(dev);
The possible values and the resulting sysfs attribute contents are:
DEVICE_REMOVABLE_UNKNOWN -> "unknown"
DEVICE_REMOVABLE -> "removable"
DEVICE_FIXED -> "fixed"
Convert the USB "removable" attribute to use this new device core
functionality. There should be no user-visible change in the location or
semantics of attribute for USB devices.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-1-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On the Realtek high-speed Hub(0bda:5487), the port which has wakeup
enabled_descendants will sometimes timeout when setting PORT_SUSPEND
feature. After checking the PORT_SUSPEND bit in wPortStatus, it is
already set which means the port has been suspended. We should treat
it suspended to make sure it will be resumed correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Link: https://lore.kernel.org/r/20210514045405.5261-2-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
CC: <stable@vger.kernel.org>
Reported-by: Tianping Fang <tianping.fang@mediatek.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210512020738.52961-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408130831.56239-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check for usb_device->ssp_rate to print the SuperSpeed Plus signaling
rate generation and lane count.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/df0986bbe92251c104dd92e3c796df7c4f2674ce.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The get_port_ssp_rate() can replace port_speed_is_ssp(). If the port
speed is detected to be in gen2x1, gen1x2, or gen2x2, then the port is
operating at SuperSpeed Plus.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/dfd61ae637597bad502d2420b4dbd3774fc76aab.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce ssp_rate field to usb_device structure to capture the
connected SuperSpeed Plus signaling rate generation and lane count with
the corresponding usb_ssp_rate enum.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b7805d121e5ae4ad5ae144bd860b6ac04ee47436.1615432770.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usage of in_interrupt() in drivers is phased out for various reasons.
Various comments use !in_interrupt() to describe calling context for
functions which might sleep. That's wrong because the calling context has
to be preemptible task context, which is not what !in_interrupt()
describes.
Replace !in_interrupt() with more accurate plain text descriptions.
The comment for usb_hcd_poll_rh_status() is misleading as this function is
called from all kinds of contexts including preemptible task
context. Remove it as there is obviously no restriction.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101110.851821025@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Description based on one by Yasushi Asano:
According to 6.7.22 A-UUT “Device No Response” for connection timeout
of USB OTG and EH automated compliance plan v1.2, enumeration failure
has to be detected within 30 seconds. However, the old and new
enumeration schemes each make a total of 12 attempts, and each attempt
can take 5 seconds to time out, so the PET test fails.
This patch adds a new Kconfig option (CONFIG_USB_FEW_INIT_RETRIES);
when the option is set all the initialization retry loops except the
outermost are reduced to a single iteration. This reduces the total
number of attempts to four, allowing Linux hosts to pass the PET test.
The new option is disabled by default to preserve the existing
behavior. The reduced number of retries may fail to initialize a few
devices that currently do work, but for the most part there should be
no change. And in cases where the initialization does fail, it will
fail much more quickly.
Reported-and-tested-by: yasushi asano <yazzep@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152217.GB134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The SET_CONFIG_TRIES macro in hub.c is badly named; it controls the
number of port-initialization retry attempts rather than the number of
Set-Configuration attempts. Furthermore, the USE_NEW_SCHEME macro and
use_new_scheme() function are written in a very confusing manner,
making it almost impossible to figure out exactly what they do or
check that they are correct.
This patch renames SET_CONFIG_TRIES to PORT_INIT_TRIES, removes
USE_NEW_SCHEME entirely, and rewrites use_new_scheme() to be much more
transparent, with added comments explaining how it works. The patch
also pulls the single call site of use_new_scheme() out from the
Get-Descriptor retry loop (where it returns the same value each time)
and renames the local variable used to store the result.
The overall effect is a minor cleanup. However, there is one
functional change: If the "use_both_schemes" module parameter isn't
set (by default it is set), the existing code does only two retry
iterations. After this patch it will always perform four, regardless
of the parameter's value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152050.GA134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit d6a499249543356002a1efbb26254c7272e62f4c.
Control messages are needed in contexts when memory allocations
are restricted, such as handling device resets and runtime PM.
For this reason the control message API internally uses GFP_NOIO.
This is a band aid introduced because when we recognized the issue,
the call chains were highly convoluted. Continuing this trend
is not a good idea.
So I am shooting the whole kennel here.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler and the code smaller.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200914153756.3412156-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200707195607.GA4198@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename the list of specific devices that an OTG device could support to
make it more obvious as to what this list is for and what it is doing.
Also rename the configuration option to make it more obvious as well.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: "Diego Elio Pettenò" <flameeyes@flameeyes.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Qi Zhou <atmgnd@outlook.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: Harry Pan <harry.pan@intel.com>
Cc: David Heinzelmann <heinzelmann.david@gmail.com>
Cc: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200618094300.1887727-9-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB OTG code has the ability to disable external hubs, but the
configuration option for it is oddly named. Rename it to be more
obvious as to what it does.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Bin Liu <b-liu@ti.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: David Heinzelmann <heinzelmann.david@gmail.com>
Cc: "Lee, Chiasheng" <chiasheng.lee@intel.com>
Cc: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20200618094300.1887727-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Tue, May 12, 2020 at 09:36:07PM +0800, Kai-Heng Feng wrote [1]:
> This patch prevents my Raven Ridge xHCI from getting runtime suspend.
The problem described in v5.6 commit 1208f9e1d758c9 ("USB: hub: Fix the
broken detection of USB3 device in SMSC hub") applies solely to the
USB5534B hub [2] present on the Kingfisher Infotainment Carrier Board,
manufactured by Shimafuji Electric Inc [3].
Despite that, the aforementioned commit applied the quirk to _all_ hubs
carrying vendor ID 0x424 (i.e. SMSC), of which there are more [4] than
initially expected. Consequently, the quirk is now enabled on platforms
carrying SMSC/Microchip hub models which potentially don't exhibit the
original issue.
To avoid reports like [1], further limit the quirk's scope to
USB5534B [2], by employing both Vendor and Product ID checks.
Tested on H3ULCB + Kingfisher rev. M05.
[1] https://lore.kernel.org/linux-renesas-soc/73933975-6F0E-40F5-9584-D2B8F615C0F3@canonical.com/
[2] https://www.microchip.com/wwwproducts/en/USB5534B
[3] http://www.shimafuji.co.jp/wp/wp-content/uploads/2018/08/SBEV-RCAR-KF-M06Board_HWSpecificationEN_Rev130.pdf
[4] https://devicehunt.com/search/type/usb/vendor/0424/device/any
Fixes: 1208f9e1d758c9 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org # v4.14+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200514220246.13290-1-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the following coccicheck warning:
drivers/usb/core/hub.c:95:12-28: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200426094147.23467-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
first for high speed devices")
Commit bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for
high speed devices") changed the way the hub driver enumerates
high-speed devices. Instead of using the "new" enumeration scheme
first and switching to the "old" scheme if that doesn't work, we start
with the "old" scheme. In theory this is better because the "old"
scheme is slightly faster -- it involves resetting the device only
once instead of twice.
However, for a long time Windows used only the "new" scheme. Zeng Tao
said that Windows 8 and later use the "old" scheme for high-speed
devices, but apparently there are some devices that don't like it.
William Bader reports that the Ricoh webcam built into his Sony Vaio
laptop not only doesn't enumerate under the "old" scheme, it gets hung
up so badly that it won't then enumerate under the "new" scheme! Only
a cold reset will fix it.
Therefore we will revert the commit and go back to trying the "new"
scheme first for high-speed devices.
Reported-and-tested-by: William Bader <williambader@hotmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207219
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for high speed devices")
CC: Zeng Tao <prime.zeng@hisilicon.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221611230.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 8099f58f1ecd ("USB: hub: Don't record a connect-change event
during reset-resume") wasn't very well conceived. The problem it
tried to fix was that if a connect-change event occurred while the
system was asleep (such as a device disconnecting itself from the bus
when it is suspended and then reconnecting when it resumes)
requiring a reset-resume during the system wakeup transition, the hub
port's change_bit entry would remain set afterward. This would cause
the hub driver to believe another connect-change event had occurred
after the reset-resume, which was wrong and would lead the driver to
send unnecessary requests to the device (which could interfere with a
firmware update).
The commit tried to fix this by not setting the change_bit during the
wakeup. But this was the wrong thing to do; it means that when a
device is unplugged while the system is asleep, the hub driver doesn't
realize anything has happened: The change_bit flag which would tell it
to handle the disconnect event is clear.
The commit needs to be reverted and the problem fixed in a different
way. Fortunately an alternative solution was noted in the commit's
Changelog: We can continue to set the change_bit entry in
hub_activate() but then clear it when a reset-resume occurs. That way
the the hub driver will see the change_bit when a device is
disconnected but won't see it when the device is still present.
That's what this patch does.
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8099f58f1ecd ("USB: hub: Don't record a connect-change event during reset-resume")
Tested-by: Paul Zimmerman <pauldzim@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221602480.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:
On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.
Factor out the usb_remove_device() change into a standalone patch to
allow conflict-free integration on top of the earliest stable branches.
[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org
Fixes: 253e05724f9230 ("USB: add a "remove hardware" sysfs attribute")
Cc: stable@vger.kernel.org # v2.6.33+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Address below Coverity complaint (Feb 25, 2020, 8:06 AM CET):
*** CID 1458999: Error handling issues (CHECKED_RETURN)
/drivers/usb/core/hub.c: 1869 in hub_probe()
1863
1864 if (id->driver_info & HUB_QUIRK_CHECK_PORT_AUTOSUSPEND)
1865 hub->quirk_check_port_auto_suspend = 1;
1866
1867 if (id->driver_info & HUB_QUIRK_DISABLE_AUTOSUSPEND) {
1868 hub->quirk_disable_autosuspend = 1;
>>> CID 1458999: Error handling issues (CHECKED_RETURN)
>>> Calling "usb_autopm_get_interface" without checking return value (as is done elsewhere 97 out of 111 times).
1869 usb_autopm_get_interface(intf);
1870 }
1871
1872 if (hub_configure(hub, &desc->endpoint[0].desc) >= 0)
1873 return 0;
1874
Rather than checking the return value of 'usb_autopm_get_interface()',
switch to the usb_autopm_get_interface_no_resume() API, as per:
On Tue, Feb 25, 2020 at 10:32:32AM -0500, Alan Stern wrote:
------ 8< ------
> This change (i.e. 'ret = usb_autopm_get_interface') is not necessary,
> because the resume operation cannot fail at this point (interfaces
> are always powered-up during probe). A better solution would be to
> call usb_autopm_get_interface_no_resume() instead.
------ 8< ------
Fixes: 1208f9e1d758c9 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: stable@vger.kernel.org # v4.14+
Reported-by: scan-admin@coverity.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-1-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Paul Zimmerman reports that his USB Bluetooth adapter sometimes
crashes following system resume, when it receives a
Get-Device-Descriptor request while it is busy doing something else.
Such a request was added by commit a4f55d8b8c14 ("usb: hub: Check
device descriptor before resusciation"). It gets sent when the hub
driver's work thread checks whether a connect-change event on an
enabled port really indicates a new device has been connected, as
opposed to an old device momentarily disconnecting and then
reconnecting (which can happen with xHCI host controllers, since they
automatically enable connected ports).
The same kind of thing occurs when a port's power session is lost
during system suspend. When the system wakes up it sees a
connect-change event on the port, and if the child device's
persist_enabled flag was set then hub_activate() sets the device's
reset_resume flag as well as the port's bit in hub->change_bits. The
reset-resume code then takes responsibility for checking that the same
device is still attached to the port, and it does this as part of the
device's resume pathway. By the time the hub driver's work thread
starts up again, the device has already been fully reinitialized and
is busy doing its own thing. There's no need for the work thread to
do the same check a second time, and in fact this unnecessary check is
what caused the problem that Paul observed.
Note that performing the unnecessary check is not actually a bug.
Devices are supposed to be able to send descriptors back to the host
even when they are busy doing something else. The underlying cause of
Paul's problem lies in his Bluetooth adapter. Nevertheless, we
shouldn't perform the same check twice in a row -- and as a nice side
benefit, removing the extra check allows the Bluetooth adapter to work
more reliably.
The work thread performs its check when it sees that the port's bit is
set in hub->change_bits. In this situation that bit is interpreted as
though a connect-change event had occurred on the port _after_ the
reset-resume, which is not what actually happened.
One possible fix would be to make the reset-resume code clear the
port's bit in hub->change_bits. But it seems simpler to just avoid
setting the bit during hub_activate() in the first place. That's what
this patch does.
(Proving that the patch is correct when CONFIG_PM is disabled requires
a little thought. In that setting hub_activate() will be called only
for initialization and resets, since there won't be any resumes or
reset-resumes. During initialization and hub resets the hub doesn't
have any child devices, and so this code path never gets executed.)
Reported-and-tested-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://marc.info/?t=157949360700001&r=1&w=2
CC: David Heinzelmann <heinzelmann.david@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001311037460.1577-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Renesas R-Car H3ULCB + Kingfisher Infotainment Board is either not able
to detect the USB3.0 mass storage devices or is detecting those as
USB2.0 high speed devices.
The explanation given by Renesas is that, due to a HW issue, the XHCI
driver does not wake up after going to sleep on connecting a USB3.0
device.
In order to mitigate that, disable the auto-suspend feature
specifically for SMSC hubs from hub_probe() function, as a quirk.
Renesas Kingfisher Infotainment Board has two USB3.0 ports (CN2) which
are connected via USB5534B 4-port SuperSpeed/Hi-Speed, low-power,
configurable hub controller.
[1] SanDisk USB 3.0 device detected as USB-2.0 before the patch
[ 74.036390] usb 5-1.1: new high-speed USB device number 4 using xhci-hcd
[ 74.061598] usb 5-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
[ 74.069976] usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 74.077303] usb 5-1.1: Product: Ultra
[ 74.080980] usb 5-1.1: Manufacturer: SanDisk
[ 74.085263] usb 5-1.1: SerialNumber: 4C530001110208116550
[2] SanDisk USB 3.0 device detected as USB-3.0 after the patch
[ 34.565078] usb 6-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[ 34.588719] usb 6-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
[ 34.597098] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 34.604430] usb 6-1.1: Product: Ultra
[ 34.608110] usb 6-1.1: Manufacturer: SanDisk
[ 34.612397] usb 6-1.1: SerialNumber: 4C530001110208116550
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1580989763-32291-1-git-send-email-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If hub_activate() is called before D+ has stabilized after remote
wakeup, the following situation might occur:
__ ___________________
/ \ /
D+ __/ \__/
Hub _______________________________
| ^ ^ ^
| | | |
Host _____v__|___|___________|______
| | | |
| | | \-- Interrupt Transfer (*3)
| | \-- ClearPortFeature (*2)
| \-- GetPortStatus (*1)
\-- Host detects remote wakeup
- D+ goes high, Host starts running by remote wakeup
- D+ is not stable, goes low
- Host requests GetPortStatus at (*1) and gets the following hub status:
- Current Connect Status bit is 0
- Connect Status Change bit is 1
- D+ stabilizes, goes high
- Host requests ClearPortFeature and thus Connect Status Change bit is
cleared at (*2)
- After waiting 100 ms, Host starts the Interrupt Transfer at (*3)
- Since the Connect Status Change bit is 0, Hub returns NAK.
In this case, port_event() is not called in hub_event() and Host cannot
recognize device. To solve this issue, flag change_bits even if only
Connect Status Change bit is 1 when got in the first GetPortStatus.
This issue occurs rarely because it only if D+ changes during a very
short time between GetPortStatus and ClearPortFeature. However, it is
fatal if it occurs in embedded system.
Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to bd0e6c9614b9 ("usb: hub: try old enumeration scheme first
for high speed devices") the kernel will try the old enumeration scheme
first for high speed devices. This can happen when a high speed device
is plugged in.
But due to missing parentheses in the USE_NEW_SCHEME define, this logic
can get messed up and the incorrect result happens.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Qi Zhou <atmgnd@outlook.com>
Link: https://lore.kernel.org/r/ht4mtag8ZP-HKEhD0KkJhcFnVlOFV8N8eNjJVRD9pDkkLUNhmEo8_cL_sl7xy9mdajdH-T8J3TFQsjvoYQT61NFjQXy469Ed_BbBw_x4S1E=@protonmail.com
[ fixup changelog text - gregkh]
Cc: stable <stable@vger.kernel.org>
Fixes: bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for high speed devices")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add kcov_remote_start()/kcov_remote_stop() annotations to the
hub_event() function, which is responsible for processing events on USB
buses, in particular events that happen during USB device enumeration.
Since hub_event() is run in a global background kernel thread (see
Documentation/dev-tools/kcov.rst for details), each USB bus gets a
unique global handle from the USB subsystem kcov handle range. As the
result kcov can now be used to collect coverage from events that happen
on a particular USB bus.
[akpm@linux-foundation.org: avoid patch conflicts to make life easier for Andrew]
Link: http://lkml.kernel.org/r/de4fe1c219db2d002d905dc1736e2a3bfa1db997.1572366574.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Potapenko <glider@google.com>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Windsor <dwindsor@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Elena Reshetova <elena.reshetova@intel.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marco Elver <elver@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging
cable to the ethernet port, the hub and roothub get runtime resumed and
runtime suspended immediately:
...
[ 433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[ 433.315204] usb usb4: usb auto-resume
[ 433.315226] hub 4-0:1.0: hub_resume
[ 433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343
[ 433.315264] usb usb4-port1: status 0343 change 0001
[ 433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2
[ 433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0
[ 433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[ 433.422307] usb usb4-port1: do warm reset
[ 433.422311] usb 4-1: device reset not allowed in state 8
[ 433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
[ 433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[ 433.422356] usb usb4-port1: do warm reset
[ 433.422358] usb 4-1: device reset not allowed in state 8
[ 433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status = 0xf0002e2
[ 433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0
[ 433.422465] hub 4-0:1.0: hub_suspend
[ 433.422475] usb usb4: bus auto-suspend, wakeup 1
[ 433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling.
[ 433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[ 433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0
[ 433.862445] xhci_hcd 0000:3a:00.0: PME# enabled
[ 433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20)
[ 433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403)
[ 433.902490] xhci_hcd 0000:3a:00.0: PME# disabled
[ 433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering
[ 433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[ 433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt!
[ 433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2
[ 433.902842] xhci_hcd 0000:3a:00.0: resume root hub
[ 433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling.
[ 433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling.
[ 433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[ 433.902919] usb usb4: usb wakeup-resume
[ 433.902942] usb usb4: usb auto-resume
[ 433.902966] hub 4-0:1.0: hub_resume
...
As Mathias pointed out, the hub enters Cold Attach Status state and
requires a warm reset. However usb_reset_device() bails out early when
the device is in suspended state, as its callers port_event() and
hub_event() don't always resume the device.
Since there's nothing wrong to reset a suspended device, allow
usb_reset_device() to do so to solve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a device connected to an xHCI host controller disconnects from the USB bus
and then reconnects, e.g. triggered by a firmware update, then the host
controller automatically activates the connection and the port is enabled. The
implementation of hub_port_connect_change() assumes that if the port is
enabled then nothing has changed. There is no check if the USB descriptors
have changed. As a result, the kernel's internal copy of the descriptors ends
up being incorrect and the device doesn't work properly anymore.
The solution to the problem is for hub_port_connect_change() always to
check whether the device's descriptors have changed before resuscitating
an enabled port.
Signed-off-by: David Heinzelmann <heinzelmann.david@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191009044647.24536-1-heinzelmann.david@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With Link Power Management (LPM) enabled USB3 links transition to low
power U1/U2 link states from U0 state automatically.
Current hub code detects USB3 remote wakeups by checking if the software
state still shows suspended, but the link has transitioned from suspended
U3 to enabled U0 state.
As it takes some time before the hub thread reads the port link state
after a USB3 wake notification, the link may have transitioned from U0
to U1/U2, and wake is not detected by hub code.
Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup
handling
This patch should be added to stable kernels since 4.13 where LPM was
kept enabled during suspend/resume
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
