summaryrefslogtreecommitdiffstats
path: root/drivers/usb/core/hub.c
AgeCommit message (Collapse)AuthorFilesLines
2020-01-15usb: core: hub: Improved device recognition on remote wakeupKeiya Nobuta1-0/+1
If hub_activate() is called before D+ has stabilized after remote wakeup, the following situation might occur: __ ___________________ / \ / D+ __/ \__/ Hub _______________________________ | ^ ^ ^ | | | | Host _____v__|___|___________|______ | | | | | | | \-- Interrupt Transfer (*3) | | \-- ClearPortFeature (*2) | \-- GetPortStatus (*1) \-- Host detects remote wakeup - D+ goes high, Host starts running by remote wakeup - D+ is not stable, goes low - Host requests GetPortStatus at (*1) and gets the following hub status: - Current Connect Status bit is 0 - Connect Status Change bit is 1 - D+ stabilizes, goes high - Host requests ClearPortFeature and thus Connect Status Change bit is cleared at (*2) - After waiting 100 ms, Host starts the Interrupt Transfer at (*3) - Since the Connect Status Change bit is 0, Hub returns NAK. In this case, port_event() is not called in hub_event() and Host cannot recognize device. To solve this issue, flag change_bits even if only Connect Status Change bit is 1 when got in the first GetPortStatus. This issue occurs rarely because it only if D+ changes during a very short time between GetPortStatus and ClearPortFeature. However, it is fatal if it occurs in embedded system. Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-08usb: missing parentheses in USE_NEW_SCHEMEQi Zhou1-1/+1
According to bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for high speed devices") the kernel will try the old enumeration scheme first for high speed devices. This can happen when a high speed device is plugged in. But due to missing parentheses in the USE_NEW_SCHEME define, this logic can get messed up and the incorrect result happens. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Qi Zhou <atmgnd@outlook.com> Link: https://lore.kernel.org/r/ht4mtag8ZP-HKEhD0KkJhcFnVlOFV8N8eNjJVRD9pDkkLUNhmEo8_cL_sl7xy9mdajdH-T8J3TFQsjvoYQT61NFjQXy469Ed_BbBw_x4S1E=@protonmail.com [ fixup changelog text - gregkh] Cc: stable <stable@vger.kernel.org> Fixes: bd0e6c9614b9 ("usb: hub: try old enumeration scheme first for high speed devices") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-04usb, kcov: collect coverage from hub_eventAndrey Konovalov1-0/+5
Add kcov_remote_start()/kcov_remote_stop() annotations to the hub_event() function, which is responsible for processing events on USB buses, in particular events that happen during USB device enumeration. Since hub_event() is run in a global background kernel thread (see Documentation/dev-tools/kcov.rst for details), each USB bus gets a unique global handle from the USB subsystem kcov handle range. As the result kcov can now be used to collect coverage from events that happen on a particular USB bus. [akpm@linux-foundation.org: avoid patch conflicts to make life easier for Andrew] Link: http://lkml.kernel.org/r/de4fe1c219db2d002d905dc1736e2a3bfa1db997.1572366574.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Alexander Potapenko <glider@google.com> Cc: Anders Roxell <anders.roxell@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Windsor <dwindsor@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Elena Reshetova <elena.reshetova@intel.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Marco Elver <elver@google.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-11-07usb: Allow USB device to be warm reset in suspended stateKai-Heng Feng1-3/+2
On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging cable to the ethernet port, the hub and roothub get runtime resumed and runtime suspended immediately: ... [ 433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0 [ 433.315204] usb usb4: usb auto-resume [ 433.315226] hub 4-0:1.0: hub_resume [ 433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343 [ 433.315264] usb usb4-port1: status 0343 change 0001 [ 433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2 [ 433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0 [ 433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343 [ 433.422307] usb usb4-port1: do warm reset [ 433.422311] usb 4-1: device reset not allowed in state 8 [ 433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000 [ 433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343 [ 433.422356] usb usb4-port1: do warm reset [ 433.422358] usb 4-1: device reset not allowed in state 8 [ 433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status = 0xf0002e2 [ 433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0 [ 433.422465] hub 4-0:1.0: hub_suspend [ 433.422475] usb usb4: bus auto-suspend, wakeup 1 [ 433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling. [ 433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001 [ 433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0 [ 433.862445] xhci_hcd 0000:3a:00.0: PME# enabled [ 433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20) [ 433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403) [ 433.902490] xhci_hcd 0000:3a:00.0: PME# disabled [ 433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering [ 433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001 [ 433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt! [ 433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2 [ 433.902842] xhci_hcd 0000:3a:00.0: resume root hub [ 433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling. [ 433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling. [ 433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0 [ 433.902919] usb usb4: usb wakeup-resume [ 433.902942] usb usb4: usb auto-resume [ 433.902966] hub 4-0:1.0: hub_resume ... As Mathias pointed out, the hub enters Cold Attach Status state and requires a warm reset. However usb_reset_device() bails out early when the device is in suspended state, as its callers port_event() and hub_event() don't always resume the device. Since there's nothing wrong to reset a suspended device, allow usb_reset_device() to do so to solve the issue. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-10usb: hub: Check device descriptor before resusciationDavid Heinzelmann1-85/+111
If a device connected to an xHCI host controller disconnects from the USB bus and then reconnects, e.g. triggered by a firmware update, then the host controller automatically activates the connection and the port is enabled. The implementation of hub_port_connect_change() assumes that if the port is enabled then nothing has changed. There is no check if the USB descriptors have changed. As a result, the kernel's internal copy of the descriptors ends up being incorrect and the device doesn't work properly anymore. The solution to the problem is for hub_port_connect_change() always to check whether the device's descriptors have changed before resuscitating an enabled port. Signed-off-by: David Heinzelmann <heinzelmann.david@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20191009044647.24536-1-heinzelmann.david@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-03usb: Handle USB3 remote wakeup for LPM enabled devices correctlyLee, Chiasheng1-2/+5
With Link Power Management (LPM) enabled USB3 links transition to low power U1/U2 link states from U0 state automatically. Current hub code detects USB3 remote wakeups by checking if the software state still shows suspended, but the link has transitioned from suspended U3 to enabled U0 state. As it takes some time before the hub thread reads the port link state after a USB3 wake notification, the link may have transitioned from U0 to U1/U2, and wake is not detected by hub code. Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup handling This patch should be added to stable kernels since 4.13 where LPM was kept enabled during suspend/resume Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by: Lee, Chiasheng <chiasheng.lee@intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-20USB: core: correct a spelling mistake in the commentHarry Pan1-1/+1
Fix a spelling typo in the function comment. Signed-off-by: Harry Pan <harry.pan@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05usb: Add devaddr in struct usb_deviceJim Lin1-1/+3
The Clear_TT_Buffer request sent to the hub includes the address of the LS/FS child device in wValue field. usb_hub_clear_tt_buffer() uses udev->devnum to set the address wValue. This won't work for devices connected to xHC. For other host controllers udev->devnum is the same as the address of the usb device, chosen and set by usb core. With xHC the controller hardware assigns the address, and won't be the same as devnum. Here we add devaddr in "struct usb_device" for usb_hub_clear_tt_buffer() to use. Signed-off-by: Jim Lin <jilin@nvidia.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21usb: core: hub: Disable hub-initiated U1/U2Thinh Nguyen1-12/+16
If the device rejects the control transfer to enable device-initiated U1/U2 entry, then the device will not initiate U1/U2 transition. To improve the performance, the downstream port should not initate transition to U1/U2 to avoid the delay from the device link command response (no packet can be transmitted while waiting for a response from the device). If the device has some quirks and does not implement U1/U2, it may reject all the link state change requests, and the downstream port may resend and flood the bus with more requests. This will affect the device performance even further. This patch disables the hub-initated U1/U2 if the device-initiated U1/U2 entry fails. Reference: USB 3.2 spec 7.2.4.2.3 Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21usb: core: hub: Enable/disable U1/U2 in configured stateThinh Nguyen1-2/+2
SET_FEATURE(U1/U2_ENABLE) and CLEAR_FEATURE(U1/U2) only apply while the device is in configured state. Add proper check in usb_disable_lpm() and usb_enable_lpm() for enabling/disabling device-initiated U1/U2. Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-03Merge tag 'usb-for-v5.2' of ↵Greg Kroah-Hartman1-3/+4
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next Felipe writes: USB: changes for v5.2 merge window With a total of 50 non-merge commits, this is not a large pull request. Most of the changes are, again, in dwc2 (37%) and dwc3 (32%) with the rest of it scattered among other UDCs, function drivers and device-tree bindings. No really big feature this time around apart from support to Amlogic being added to both dwc3 and dwc2 drivers. * tag 'usb-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (50 commits) usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA usb: dwc3: Fix default lpm_nyet_threshold value usb: dwc3: debug: Print GET_STATUS(device) tracepoint usb: dwc3: Do core validation early on probe usb: dwc3: gadget: Set lpm_capable usb: gadget: atmel: tie wake lock to running clock usb: gadget: atmel: support USB suspend usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask dwc2: gadget: Fix completed transfer size calculation in DDMA usb: dwc2: Set lpm mode parameters depend on HW configuration usb: dwc2: Fix channel disable flow usb: dwc2: Set actual frame number for completed ISOC transfer usb: gadget: do not use __constant_cpu_to_le16 usb: dwc2: gadget: Increase descriptors count for ISOC's usb: introduce usb_ep_type_string() function usb: dwc3: move synchronize_irq() out of the spinlock protected block usb: dwc3: Free resource immediately after use usb: dwc3: of-simple: Convert to bulk clk API usb: dwc2: Delayed status support usb: gadget: udc: lpc32xx: rework interrupt handling ...
2019-05-03USB: Export usb_wakeup_enabled_descendants()Douglas Anderson1-3/+4
In (e583d9d USB: global suspend and remote wakeup don't mix) we introduced wakeup_enabled_descendants() as a static function. We'd like to use this function in USB controller drivers to know if we should keep the controller on during suspend time, since doing so has a power impact. Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-04-17USB: core: Don't unbind interfaces following device reset failureAlan Stern1-1/+4
The SCSI core does not like to have devices or hosts unregistered while error recovery is in progress. Trying to do so can lead to self-deadlock: Part of the removal code tries to obtain a lock already held by the error handler. This can cause problems for the usb-storage and uas drivers, because their error handler routines perform a USB reset, and if the reset fails then the USB core automatically goes on to unbind all drivers from the device's interfaces -- all while still in the context of the SCSI error handler. As it turns out, practically all the scenarios leading to a USB reset failure end up causing a device disconnect (the main error pathway in usb_reset_and_verify_device(), at the end of the routine, calls hub_port_logical_disconnect() before returning). As a result, the hub_wq thread will soon become aware of the problem and will unbind all the device's drivers in its own context, not in the error-handler's context. This means that usb_reset_device() does not need to call usb_unbind_and_rebind_marked_interfaces() in cases where usb_reset_and_verify_device() has returned an error, because hub_wq will take care of everything anyway. This particular problem was observed in somewhat artificial circumstances, by using usbfs to tell a hub to power-down a port connected to a USB-3 mass storage device using the UAS protocol. With the port turned off, the currently executing command timed out and the error handler started running. The USB reset naturally failed, because the hub port was off, and the error handler deadlocked as described above. Not carrying out the call to usb_unbind_and_rebind_marked_interfaces() fixes this issue. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> CC: Bart Van Assche <bvanassche@acm.org> CC: Martin K. Petersen <martin.petersen@oracle.com> CC: Jacky Cao <Jacky.Cao@sony.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16USB: hub: Remove returned value 'status' since never usedMathieu Malaterre1-7/+6
The returned value in status has never been used since commit 4296c70a5ec3 ("USB/xHCI: Enable USB 3.0 hub remote wakeup.") So remove 'status' completely. Remove warning (W=1): drivers/usb/core/hub.c:3671:8: warning: variable 'status' set but not used [-Wunused-but-set-variable] Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-08usb: handle warm-reset port requests on hub resumeJan-Marek Glogowski1-0/+7
On plug-in of my USB-C device, its USB_SS_PORT_LS_SS_INACTIVE link state bit is set. Greping all the kernel for this bit shows that the port status requests a warm-reset this way. This just happens, if its the only device on the root hub, the hub therefore resumes and the HCDs status_urb isn't yet available. If a warm-reset request is detected, this sets the hubs event_bits, which will prevent any auto-suspend and allows the hubs workqueue to warm-reset the port later in port_event. Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18USB: Consolidate LPM checks to avoid enabling LPM twiceKai-Heng Feng1-8/+4
USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working after S3: [ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin [ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110) After some experiments, I found that disabling LPM can workaround the issue. On some platforms, the USB power is cut during S3, so the driver uses reset-resume to resume the device. During port resume, LPM gets enabled twice, by usb_reset_and_verify_device() and usb_port_resume(). Consolidate all checks into new LPM helpers to make sure LPM only gets enabled once. Fixes: de68bab4fa96 ("usb: Don't enable USB 2.0 Link PM by default.”) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> # after much soaking Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18USB: Add new USB LPM helpersKai-Heng Feng1-6/+6
Use new helpers to make LPM enabling/disabling more clear. This is a preparation to subsequent patch. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> # after much soaking Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18usb: hub: add retry routine after intr URB submit errorNicolas Saenz Julienne1-6/+37
The hub sends hot-plug events to the host trough it's interrupt URB. The driver takes care of completing the URB and re-submitting it. Completion errors are handled in the hub_event() work, yet submission errors are ignored, rendering the device unresponsive. All further events are lost. It is fairly hard to find this issue in the wild, since you have to time the USB hot-plug event with the URB submission failure. For instance it could be the system running out of memory or some malfunction in the USB controller driver. Nevertheless, it's pretty reasonable to think it'll happen sometime. One can trigger this issue using eBPF's function override feature (see BCC's inject.py script). This patch adds a retry routine to the event of a submission error. The HUB driver will try to re-submit the URB once every second until it's successful or the HUB is disconnected. As some USB subsystems already take care of this issue, the implementation was inspired from usbhid/hid_core.c's. Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Oliver Neukum <oneukum@suse.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-10Merge 4.20-rc6 into usb-nextGreg Kroah-Hartman1-2/+3
We want the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05USB: check usb_get_extra_descriptor for proper sizeMathias Payer1-1/+1
When reading an extra descriptor, we need to properly check the minimum and maximum size allowed, to prevent from invalid data being sent by a device. Reported-by: Hui Peng <benquike@gmail.com> Reported-by: Mathias Payer <mathias.payer@nebelwelt.net> Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Hui Peng <benquike@gmail.com> Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05USB: Fix invalid-free bug in port_over_current_notify()Alan Stern1-1/+2
Syzbot and KASAN found the following invalid-free bug in port_over_current_notify(): -------------------------------------------------------------------------- BUG: KASAN: double-free or invalid-free in port_over_current_notify drivers/usb/core/hub.c:5192 [inline] BUG: KASAN: double-free or invalid-free in port_event drivers/usb/core/hub.c:5241 [inline] BUG: KASAN: double-free or invalid-free in hub_event+0xd97/0x4140 drivers/usb/core/hub.c:5384 CPU: 1 PID: 32710 Comm: kworker/1:3 Not tainted 4.20.0-rc3+ #129 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x244/0x39d lib/dump_stack.c:113 print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256 kasan_report_invalid_free+0x64/0xa0 mm/kasan/report.c:336 __kasan_slab_free+0x13a/0x150 mm/kasan/kasan.c:501 kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528 __cache_free mm/slab.c:3498 [inline] kfree+0xcf/0x230 mm/slab.c:3817 port_over_current_notify drivers/usb/core/hub.c:5192 [inline] port_event drivers/usb/core/hub.c:5241 [inline] hub_event+0xd97/0x4140 drivers/usb/core/hub.c:5384 process_one_work+0xc90/0x1c40 kernel/workqueue.c:2153 worker_thread+0x17f/0x1390 kernel/workqueue.c:2296 kthread+0x35a/0x440 kernel/kthread.c:246 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352 -------------------------------------------------------------------------- The problem is caused by use of a static array to store environment-string pointers. When the routine is called by multiple threads concurrently, the pointers from one thread can overwrite those from another. The solution is to use an ordinary automatic array instead of a static array. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: syzbot+98881958e1410ec7e53c@syzkaller.appspotmail.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-05usb: hub: delay hub autosuspend if USB3 port is still link trainingMathias Nyman1-0/+10
When initializing a hub we want to give a USB3 port in link training the same debounce delay time before autosuspening the hub as already trained, connected enabled ports. USB3 ports won't reach the enabled state with "current connect status" and "connect status change" bits set until the USB3 link training finishes. Catching the port in link training (polling) and adding the debounce delay prevents unnecessary failed attempts to autosuspend the hub. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-14usb: core: Fix hub port connection events lostDennis Wassenberg1-1/+3
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset only if a device is was attached to the hub port before resetting the hub port. Using a Lenovo T480s attached to the ultra dock it was not possible to detect some usb-c devices at the dock usb-c ports because the hub_port_reset code will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset. Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit. This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the new device was attached such that it was not detected. This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is currently no device attached to the port before the hub port reset. This will avoid clearing the connection bit for new attached devices. Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com> Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-07USB: Wait for extra delay time after USB_PORT_FEAT_RESET for quirky hubKai-Heng Feng1-3/+11
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may fail to work after the system resumes from suspend: [ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd [ 206.143691] usb 3-2.4: device descriptor read/64, error -32 [ 206.351671] usb 3-2.4: device descriptor read/64, error -32 Info for this hub: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1a40 ProdID=0101 Rev=01.11 S: Product=USB 2.0 Hub C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub Some expirements indicate that the USB devices connected to the hub are innocent, it's the hub itself is to blame. The hub needs extra delay time after it resets its port. Hence wait for extra delay, if the device is connected to this quirky hub. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-09usb: core: fix memory leak on port_dev_path allocationColin Ian King1-1/+3
Currently the allocation of port_dev_path from the call to kobject_get_path is not being kfree'd, causing a memory leak. Fix this by kfree'ing this at the end of the function. Add an extra error exit path to fix one of the early leaks when envp[0] fails to be allocated. Detected by CoverityScan, CID#1473771 ("Resource Leak") Fixes: 201af55da8a3 ("usb: core: added uevent for over-current") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-02usb: hub: try old enumeration scheme first for high speed devicesZeng Tao1-1/+3
The new scheme is required just to support legacy low and full-speed devices. For high speed devices, it will slower the enumeration speed. So in this patch we try the "old" enumeration scheme first for high speed devices, and this is what Windows does since Windows 8. Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-28usb: core: added uevent for over-currentJon Flatley1-0/+36
After commit 1cbd53c8cd85 ("usb: core: introduce per-port over-current counters") usb ports expose a sysfs value 'over_current_count' to user space. This value on its own is not very useful as it requires manual polling. As a solution, fire a udev event from the usb hub device that specifies the values 'OVER_CURRENT_PORT' and 'OVER_CURRENT_COUNT' that indicate the path of the usb port where the over-current event occurred and the value of 'over_current_count' in sysfs. Additionally, call sysfs_notify() so the sysfs value supports poll(). Signed-off-by: Jon Flatley <jflat@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-30Merge 4.18-rc7 into usb-nextGreg Kroah-Hartman1-2/+6
We want the USB fixes in here as well to handle merge issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-21usb: core: handle hub C_PORT_OVER_CURRENT conditionBin Liu1-2/+6
Based on USB2.0 Spec Section 11.12.5, "If a hub has per-port power switching and per-port current limiting, an over-current on one port may still cause the power on another port to fall below specific minimums. In this case, the affected port is placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the port, but PORT_OVER_CURRENT is not set." so let's check C_PORT_OVER_CURRENT too for over current condition. Fixes: 08d1dec6f405 ("usb:hub set hub->change_bits when over-current happens") Cc: <stable@vger.kernel.org> Tested-by: Alessandro Antenucci <antenucci@korg.it> Signed-off-by: Bin Liu <b-liu@ti.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-25USB: Report wakeup events on root-hub portsAlan Stern1-0/+42
When a USB device attached to a root-hub port sends a wakeup request to a sleeping system, we do not report the wakeup event to the PM core. This is because a system resume involves waking up all suspended USB ports as quickly as possible; without the normal USB_RESUME_TIMEOUT delay, the host controller driver doesn't set the USB_PORT_STAT_C_SUSPEND flag and so usb_port_resume() doesn't realize that a wakeup request was received. However, some environments (such as Chrome OS) want to have all wakeup events reported so they can be ascribed to the appropriate device. To accommodate these environments, this patch adds a new routine to the hub driver and a corresponding new HCD method to be used when a root hub resumes. The HCD method returns a bitmap of ports that have initiated a wakeup signal but not yet completed resuming. The hub driver can then report to the PM core that the child devices attached to these ports initiated a wakeup event. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Suggested-by: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook1-1/+1
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-05-31usb: hub: Per-port setting to reduce TRSTRCY to 10 msNicolas Boichat1-1/+5
Currently, the USB hub core waits for 50 ms after enumerating the device. This was added to help "some high speed devices" to enumerate (b789696af8 "[PATCH] USB: relax usbcore reset timings"). On some devices, the time-to-active is important, so we provide a per-port option to reduce the time to what the USB specification requires: 10 ms. Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-31usb: hub: Per-port setting to use old enumeration schemeNicolas Boichat1-4/+9
The "old" enumeration scheme is considerably faster (it takes ~244ms instead of ~356ms to get the descriptor). It is currently only possible to use the old scheme globally (/sys/module/usbcore/parameters/old_scheme_first), which is not desirable as the new scheme was introduced to increase compatibility with more devices. However, in our case, we care about time-to-active for a specific USB device (which we make the firmware for), on a specific port (that is pogo-pin based: not a standard USB port). This new sysfs option makes it possible to use the old scheme on a single port only. Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-30Merge 4.17-rc3 into usb-nextGreg Kroah-Hartman1-1/+9
This resolves the merge issue with drivers/usb/core/hcd.c Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-25usb: do not reset if a low-speed or full-speed device timed outMaxim Moseychuk1-1/+3
Some low-speed and full-speed devices (for example, bluetooth) do not have time to initialize. For them, ETIMEDOUT is a valid error. We need to give them another try. Otherwise, they will never be initialized correctly and in dmesg will be messages "Bluetooth: hci0 command 0x1002 tx timeout" or similars. Fixes: 264904ccc33c ("usb: retry reset if a device times out") Cc: stable <stable@vger.kernel.org> Signed-off-by: Maxim Moseychuk <franchesko.salias.hudro.pedros@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-22USB: show USB 3.2 Dual-lane devices as Gen Xx2 during device enumerationMathias Nyman1-2/+5
USB 3.2 specification adds a Gen XxY notion for USB3 devices where X is the signaling rate on the wire. Gen 1xY is 5Gbps Superspeed and Gen 2xY is 10Gbps SuperSpeedPlus. Y is the lane count. For normal, non inter-chip (SSIC) devies the rx and tx lane count is symmetric, and the maximum lane count for USB 3.2 devices is 2 (dual-lane). SSIC devices may have asymmetric lane counts, with up to four lanes per direction. The USB 3.2 specification doesn't point out how to use the Gen XxY notion for these devices, so we limit the Gen Xx2 notion to symmertic Dual lane devies. For other devices just show Gen1 or Gen2 Gen 1 5Gbps Gen 2 10Gbps Gen 1x2 10Gbps Dual-lane (USB 3.2) Gen 2x2 20Gbps Dual-lane (USB 3.2) Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-22USB: Add support to store lane count used by USB 3.2Mathias Nyman1-0/+8
USB 3.2 specification adds Dual-lane support, doubling the maximum SuperSpeedPlus data rate from 10Gbps to 20Gbps. Dual-lane takes into use a second set of rx and tx wires/pins in the Type-C cable and connector. Add "rx_lanes" and "tx_lanes" variables to struct usb_device to store the numer of lanes in use. Number of lanes can be read using the extended port status hub request that was introduced in USB 3.1. Extended port status rx and tx lane count are zero based, maximum lanes supported by non inter-chip (SSIC) USB 3.2 is 2 (dual lane) with rx and tx lane count symmetric. SSIC devices support asymmetric lanes up to 4 lanes per direction. If extended port status is not available then default to one lane. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-22usb: hub: Don't wait for connect state at resume for powered-off portsDominik Bozek1-0/+4
wait_for_connected() wait till a port change status to USB_PORT_STAT_CONNECTION, but this is not possible if the port is unpowered. The loop will only exit at timeout. Such case take place if an over-current incident happen while system is in S3. Then during resume wait_for_connected() will wait 2s, which may be noticeable by the user. Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com> Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-04-22USB: Increment wakeup count on remote wakeup.Ravi Chandra Sadineni1-1/+9
On chromebooks we depend on wakeup count to identify the wakeup source. But currently USB devices do not increment the wakeup count when they trigger the remote wake. This patch addresses the same. Resume condition is reported differently on USB 2.0 and USB 3.0 devices. On USB 2.0 devices, a wake capable device, if wake enabled, drives resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7). The upstream facing port then sets C_PORT_SUSPEND bit and reports a port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port has resumed before driving the resume signal from the host and C_PORT_SUSPEND is set, then the device attached to the given port might be the reason for the last system wakeup. Increment the wakeup count for the same. On USB 3.0 devices, a function may signal that it wants to exit from device suspend by sending a Function Wake Device Notification to the host (USB3.0 spec section 8.5.6.4) Thus on receiving the Function Wake, increment the wakeup count. Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-25USB: announce bcdDevice as well as idVendor, idProduct.Benson Leung1-2/+6
Print bcdDevice which is used by vendors to identify different versions of the same product (or different versions of firmware). Adding this to the logs will be useful for support purposes. Match the %2x.%02x formatting that's used by lsusb -v for this same value. Signed-off-by: Benson Leung <bleung@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-23usb: hub: Reduce warning to notice on power lossTomeu Vizoso1-1/+1
Currently we warn the user when the root hub lost power after resume, but the user cannot do anything about it so it should probably be a notice. This will reduce the noise in the console during suspend and resume, which is already quite significant in many systems. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-22usb: core: introduce per-port over-current countersRichard Leitner1-1/+3
For some userspace applications information on the number of over-current conditions at specific USB hub ports is relevant. In our case we have a series of USB hardware (using the cp210x driver) which communicates using a proprietary protocol. These devices sometimes trigger an over-current situation on some hubs. In case of such an over-current situation the USB devices offer an interface for reducing the max used power. As these conditions are quite rare and imply performance reductions of the device we don't want to reduce the max power always. Therefore give user-space applications the possibility to react adequately by introducing an over_current_counter in the usb port struct which is exported via sysfs. Signed-off-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-09usb: Don't disable Latency tolerance Messaging (LTM) before port resetMathias Nyman1-9/+3
Disabing Latency Tolerance Messaging before port reset is unnecessary. LTM is automatically disabled at port reset. If host can't communicate with the device the LTM message will fail, and the hub driver will unnecessarily do a logical disconnect. Broken communication is ofter the reason for a reset in the first place. Additionally we can't guarantee device is in a configured state, epecially in reset-resume case when root hub lost power. LTM can't be modified unless device is in a configured state. Just remove LTM disabling before port reset. Details about LTM and port reset in USB 3 specification: USB 3 spec section 9.4.5 "The LTM Enable field can be modified by the SetFeature() and ClearFeature() requests using the LTM_ENABLE feature selector. This field is reset to zero when the device is reset." USB 3 spec section 9.4.1 "The device shall process a Clear Feature (U1_Enable or U2_Enable or LTM_Enable) only if the device is in the configured state." Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-18Merge 4.15-rc4 into usb-nextGreg Kroah-Hartman1-0/+9
We want the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-15usb: core: add support for USB_REQ_SET_ISOCH_DELAYFelipe Balbi1-0/+30
USB SS and SSP hubs provide wHubDelay values on their hub descriptor which we should inform the USB Device about. The USB Specification 3.0 explains, on section 9.4.11, how to calculate the value and how to issue the request. Note that a USB_REQ_SET_ISOCH_DELAY is valid on all device states (Default, Address, Configured), we just *chose* to issue it from Address state right after successfully fetching the USB Device Descriptor. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-06usb: core: Fix logging messages with spurious periods after newlinesJoe Perches1-10/+7
Using a period after a newline causes bad output. Miscellanea: o Coalesce formats too Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28usb: hub: Cycle HUB power when initialization failsMike Looijmans1-0/+9
Sometimes the USB device gets confused about the state of the initialization and the connection fails. In particular, the device thinks that it's already set up and running while the host thinks the device still needs to be configured. To work around this issue, power-cycle the hub's output to issue a sort of "reset" to the device. This makes the device restart its state machine and then the initialization succeeds. This fixes problems where the kernel reports a list of errors like this: usb 1-1.3: device not accepting address 19, error -71 The end result is a non-functioning device. After this patch, the sequence becomes like this: usb 1-1.3: new high-speed USB device number 18 using ci_hdrc usb 1-1.3: device not accepting address 18, error -71 usb 1-1.3: new high-speed USB device number 19 using ci_hdrc usb 1-1.3: device not accepting address 19, error -71 usb 1-1-port3: attempt power cycle usb 1-1.3: new high-speed USB device number 21 using ci_hdrc usb-storage 1-1.3:1.2: USB Mass Storage device detected Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-07usb: core: introduce a new usb_get_std_status() helperFelipe Balbi1-4/+4
This new helper is a simple wrapper around usb_get_status(). This patch is in preparation to adding support for fetching PTM_STATUS types. No functional changes. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-03USB: core: move existing SPDX tags to top of the fileGreg Kroah-Hartman1-1/+1
To match the rest of the kernel, the SPDX tags for the drivers/usb/core/ files are moved to the first line of the file. This makes it more obvious the tag is present as well as making it match the other 12k files in the tree with this location. It also uses // to match the "expected style" as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-23Merge 4.14-rc6 into usb-nextGreg Kroah-Hartman1-4/+7
We need the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-29 14:25:03 +0000