summaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial/fsl_lpuart.c
AgeCommit message (Collapse)AuthorFilesLines
2019-11-05tty: serial: fsl_lpuart: use the sg count from dma_map_sgPeng Fan1-2/+2
The dmaengine_prep_slave_sg needs to use sg count returned by dma_map_sg, not use sport->dma_tx_nents, because the return value of dma_map_sg is not always same with "nents". When enabling iommu for lpuart + edma, iommu framework may concatenate two sgs into one. Fixes: 6250cc30c4c4e ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx") Cc: <stable@vger.kernel.org> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/1572932977-17866-1-git-send-email-peng.fan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: serial: lpuart: Add RS485 support for 32-bit uart flavourPhilippe Schenker1-2/+63
This commits adds RS485 support for LPUART hardware that uses 32-bit registers. These are typically found in i.MX8 processors. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20191017141428.10330-3-philippe.schenker@toradex.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: serial: lpuart: Use defines that correspond to correct registerPhilippe Schenker1-2/+2
Use define from the 32-bit register description UARTMODIR_* instead of UARTMODEM_*. The value is the same, so there is no functional change. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20191017141428.10330-2-philippe.schenker@toradex.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-04tty: serial: lpuart: Remove unnecessary code from set_mctrlPhilippe Schenker1-11/+0
Currently flow control is not working due to lpuart32_set_mctrl that is clearing TXCTSE bit in all cases. This bit gets earlier setup by lpuart32_set_termios. As I read in Documentation set_mctrl is also not meant for hardware flow control rather than gpio setting and clearing a RTS signal. Therefore I guess it is safe to remove the whole code in lpuart32_set_mctrl. This was tested with console on a i.MX8QXP SoC. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20191017141428.10330-1-philippe.schenker@toradex.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-07tty: serial: fsl_lpuart: Fix lpuart_flush_buffer()Andrey Smirnov1-1/+1
Fix incorrect read-modify-write sequence in lpuart_flush_buffer() that was reading from UARTPFIFO and writing to UARTCFIFO instead of operating solely on the latter. Fixes: 9bc19af9dacb ("tty: serial: fsl_lpuart: Flush HW FIFOs in .flush_buffer") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Reported-by: Vivien Didelot <vivien.didelot@gmail.com> Tested-by: Vivien Didelot <vivien.didelot@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Fabio Estevam <festevam@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Jiri Slaby <jslaby@suse.com> Link: https://lore.kernel.org/r/20191004215537.5308-1-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Ignore TX/RX interrupts if DMA is enabledAndrey Smirnov1-2/+2
In a mixed DMA/IRQ use-case (e.g.: DMA for TX, IRQ for RX), interrupt handler might try to handle Rx/Tx condition it shouldn't. Change the code to only handle TX/RX event if corresponding path isn't being handled by DMA. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190805185701.22863-7-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Don't enable TIE in .startup() or .resume()Andrey Smirnov1-1/+1
Enabling TIE in .startup() callback causes the driver to start (or at least try) to transmit data before .start_tx() is called. Which, while harmless (since TIE handler will immediately disable it), is a no-op and shouldn't really happen. Drop UARTCR2_TIE from list of bits set in lpuart_startup(). This change will also not enable TIE in .resume(), but it seems that, similart to .startup(), transmit interrupt shouldn't be enabled there either. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190805185701.22863-6-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Introduce lpuart*_setup_watermark_enable()Andrey Smirnov1-22/+28
Most users of lpuart*_setup_watermark() enable identical set of flags right after the call, so combine those two action into a subroutine and make use of it. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190805185701.22863-5-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Introduce lpuart32_configure()Andrey Smirnov1-27/+21
Code doing final steps of TX/RX configuration in lpuart32_startup() and lpuart_resume() is identical, so move it into a standalone subroutine. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190805185701.22863-4-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Introduce lpuart_rx_dma_startup()Andrey Smirnov1-23/+17
Code doing initial DMA RX configuration in lpuart_startup() and lpuart32_startup() is exactly the same, so move it into a standalone subroutine. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190805185701.22863-3-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Introduce lpuart_tx_dma_startup()Andrey Smirnov1-30/+23
Code configure DMA TX path in lpuart_startup(), lpuart32_startup() and lpuart_resume() is doing exactly the same thing, so move it into a standalone subroutine. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190805185701.22863-2-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: Remove dev_err() usage after platform_get_irq()Stephen Boyd1-3/+1
We don't need dev_err() messages when platform_get_irq() fails now that platform_get_irq() prints an error message itself when something goes wrong. Let's remove these prints with a simple semantic patch. // <smpl> @@ expression ret; struct platform_device *E; @@ ret = ( platform_get_irq(E, ...) | platform_get_irq_byname(E, ...) ); if ( \( ret < 0 \| ret <= 0 \) ) { ( -if (ret != -EPROBE_DEFER) -{ ... -dev_err(...); -... } | ... -dev_err(...); ) ... } // </smpl> While we're here, remove braces on if statements that only have one statement (manually). Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20190730181557.90391-45-swboyd@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Introduce lpuart_dma_shutdown()Andrey Smirnov1-24/+18
Last steps of .shutdown() code are identical for lpuart and lpuart32 cases, so move it all into a standalone subroutine. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-19-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Drop unnecessary lpuart*_stop_tx()Andrey Smirnov1-4/+0
By the time lpuart_shutdown() calls lpuart_stop_tx() UARTCR2_TE and UARTCR2_TIE (which the latter will clear) are already cleared, so that function call should effectively be a no-op. Moreso, lpuart_stop_tx() is expected to be executed with port spinlock held, which the caller doesn't. Given all that, drop the call to lpuart_stop_tx() in lpuart_shutdown(). In case of lpuart32_shutdown()/lpuart32_stop_tx(), TIE won't even be set if lpuart_dma_tx_use is true. Drop it there as well. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-18-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Introduce lpuart_stopped_or_empty()Andrey Smirnov1-7/+10
The check for uart_circ_empty(xmit) || uart_tx_stopped(&sport->port) appears in multiple places in the driver. Move it into a helper function. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-17-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Use cpu_relax() instead of barrier()Andrey Smirnov1-2/+2
Use cpu_relax() instead of barrier() in a tight polling loops to make them a bit more idiomatic. Should also improve things on ARM64 a bit since cpu_relax() will expand into "yield" instruction there. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-16-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Introduce lpuart_wait_bit_set()Andrey Smirnov1-20/+22
Busy polling on a bit in a register is used in multiple places in the driver. Move it into a shared function. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-15-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcsAndrey Smirnov1-14/+14
When dealing with 32-bit variant of LPUART IP block appropriate I/O helpers have to be used to properly deal with endianness differences. Change all of the offending code to do that. Fixes: a5fa2660d787 ("tty/serial/fsl_lpuart: Add CONSOLE_POLL support for lpuart32.") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-14-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Clear CSTOPB unconditionallyAndrey Smirnov1-2/+1
Clearing CSTOPB bit if it is set is functionally equivalent to jsut clearing it unconditionally. Drop unnecessary check. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-13-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Drop unnecessary extra parenthesisAndrey Smirnov1-10/+10
Drop unnecessary extra parenthesis in the driver. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-12-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Drop no-op bit opearationAndrey Smirnov1-4/+2
The check for termios->c_cflag & CRTSCTS ensure that if we reach else branch, CRTSCTS in termios->c_cflag is already going to be cleard. Doing so explicitly there is not necessary. Drop it. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-11-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fls_lpuart: Split shared TX IRQ handler into twoAndrey Smirnov1-26/+35
While sharing code for Tx interrupt handler between 8 and 32 bit variant of the peripheral saves a bit of code duplication it also adds quite a number of lpuart_is_32() checks which makes it harder to understand. Move shared bits back into corresponding lpuart*_transmit_buffer functions, split lpuart_txint into lpuart_txint and lpuart32_txint so we can drop all extra lpuart_is_32() check and make the code flow more linear. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-10-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Fix issue in software flow controlAndrey Smirnov1-0/+2
Although I haven't observed this bug in practice, it seems that the code for handling x_char of LPUART is pretty much identical to that of i.MX. So the fix found in commit 7e2fb5aa8d81 ("serial: imx: Fix issue in software flow control"): serial: imx: Fix issue in software flow control After send out x_char in UART driver, x_char needs to be cleared by UART driver itself, otherwise data in TXFIFO can no longer be sent out. Also tx counter needs to be increased to keep track of correct number of transmitted data. Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> should apply here as well. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-9-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Drop unnecessary uart_write_wakeup()Andrey Smirnov1-3/+0
Uart_write_wakeup() will already be called as a part of lpuart*_transmit_buffer() call, so there doesn't seem to be a reason to call it again right after. It also appears that second uart_write_wakeup() might potentially cause unwanted write wakeup when transmitting an x_char. See commit 5e42e9a30cda ("serial: imx: Fix x_char handling and tx flow control") where this problem was fixed in a very similarly structured i.MX UART driver. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-8-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Fix bogus indentationAndrey Smirnov1-3/+3
Fix bogus indentation in rx_dma_timer_init(). Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-6-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Simplify RX/TX IRQ handlersAndrey Smirnov1-13/+7
It appears that lpuart_rxint, lpuart_txint and lpuart32_rxint were modelled after identical function found in UART driver for i.MX. However, while said functions are used as individual IRQ handlers in i.MX driver (in case of i.MX1), it is not the case for LPUART. Given that, there's no need for us to restrict the prototype of the handler to irqreturn_t foo(int, void *) and we can drop all of uneened boilerplate code by changing it void foo(struct lpuart_port *). Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-5-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: Flush HW FIFOs in .flush_bufferAndrey Smirnov1-6/+17
Switching baud rate might cause bogus data to appear in HW FIFO. Add code to do a HW FIFO flush to .flush_buffer callback to avoid that. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-4-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: flush receive FIFO after overrunsStefan Agner1-2/+13
After overruns the FIFO pointers become misaligned. This typically shows by characters still being stuck in the FIFO despite the empty flag being asserted. After the first assertion of the overrun flag the empty flag still seems to indicate FIFO state correctly and all data can be read. However, after another overrun assertion the FIFO seems to be off by one such that the last received character is still in the FIFO (despite the empty flag being asserted). Flushing the receive FIFO reinitializes pointers. Hence it is recommended to flush the FIFO after overruns, see also: https://community.nxp.com/thread/321175 Hence, on assertion of the overrun flag read the remaining data from the FIFO and flush buffers. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-3-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: fix framing error handling when using DMAStefan Agner1-0/+26
When using DMA framing error get cleared properly. However, due to the additional read from the data register, an underflow in the receive FIFO buffer occurs (the FIFO pointer gets out of sync). Clear the FIFO in case an underflow has occurred. Also disable the receiver during this operation and when reading the data register to minimize potential interference. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-2-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: correct the FIFO depth sizeFugang Duan1-10/+9
VF610/LS1021a/i.MX7ULP/i.MX8QXP reference manual describe the TXFIFOSIZE/RXFIFOSIZE field as below. 000b - FIFO/Buffer depth = 1 dataword. 001b - FIFO/Buffer depth = 4 datawords. 010b - FIFO/Buffer depth = 8 datawords. 011b - FIFO/Buffer depth = 16 datawords. 100b - FIFO/Buffer depth = 32 datawords. 101b - FIFO/Buffer depth = 64 datawords. 110b - FIFO/Buffer depth = 128 datawords. 111b - FIFO/Buffer depth = 256 datawords. (Reserved for VF610) So the FIFO depth should be: 0x1 << (val ? (val + 1) : 0) Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20190717051930.15514-6-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: remove sg_set_buf() for sport->rx_sglFugang Duan1-1/+0
Since .sg_init_one() already set sg entry page like below code. sg_init_one() sg_init_table(sg, 1); sg_set_buf(sg, buf, buflen); So it should not set sg entry page again, remove the redundant code. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20190717051930.15514-5-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: use kzalloc() instead of kmalloc()Fugang Duan1-1/+1
Use kzalloc() instead of kmalloc() to get clean rx buffer that is useful for DMA mode debug to check the data moving validity. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20190717051930.15514-4-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: add earlycon for imx8qxp platformFugang Duan1-0/+1
Add earlycon support for imx8qxp platform. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20190717051930.15514-3-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-04tty: serial: fsl_lpuart: remove the dev.coherent_dma_mask zero settingFugang Duan1-2/+0
By default, .of_dma_configure() init dev.coherent_dma_mask to BIT(32) that match the eDMA address range. If re-init dev.coherent_dma_mask to zero, then streaming dma mapping will go swiotlb dma_map, if swiotlb is not initalized then it causes mapping failed. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20190717051930.15514-2-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-04tty: serial: fsl_lpuart: add imx8qxp supportFugang Duan1-20/+86
The lpuart of imx8ulp is basically the same as imx7ulp, but it has new feature support based on imx7ulp, like it can assert a DMA request on EOP(end-of-packet). imx8ulp lpuart use two clocks, one is ipg bus clock that is used to access registers, the other is baud clock that is used to transmit-receive data. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20190704134007.2316-1-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-18serial: fsl_lpuart: Remove unneeded OOM error messageFabio Estevam1-3/+1
There is no need to add an out-of-memory error message inside the driver because the core MM code will take care of it. Remove the unneeded OOM error message. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-10serial: fsl_lpuart: Use dev_info() instead of printk()Fabio Estevam1-2/+2
dev_info() is more appropriate for printing messages inside drivers, so switch to dev_info(). Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-30serial: fsl_lpuart: DMA support for 32-bit variantAtsushi Nemoto1-29/+163
Add DMA support for 32-bit variant of the LPUART, such as LS1021A. Signed-off-by: Tomonori Sakita <tomonori.sakita@sord.co.jp> Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-28Merge 5.0-rc4 into tty-nextGreg Kroah-Hartman1-1/+1
We need the tty and serial fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-22serial: fsl_lpuart: consider TX FIFO too in lpuart32_tx_emptyAtsushi Nemoto1-2/+12
The commit 3876a00fcb6b ("tty: serial: fsl_lpuart: consider TX FIFO too in tx_empty") fixed lpuart_tx_empty only. Fix lpuart32_tx_empty too. Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-22serial: fsl_lpuart: specify transmit FIFO size for 32-bit variantAtsushi Nemoto1-0/+2
The commit 4e8f24593709 ("tty: serial: fsl_lpuart: specify transmit FIFO size") fixed lpuart_startup only. Fix lpuart32_startup too. Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-22serial: fsl_lpuart: fix maximum acceptable baud rate with over-samplingTomonori Sakita1-1/+1
Using over-sampling ratio, lpuart can accept baud rate upto uartclk / 4. Signed-off-by: Tomonori Sakita <tomonori.sakita@sord.co.jp> Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-09serial: fsl_lpuart: clear parity enable bit when disable parityAndy Duan1-0/+4
Current driver only enable parity enable bit and never clear it when user set the termios. The fix clear the parity enable bit when PARENB flag is not set in termios->c_cflag. Cc: Lukas Wunner <lukas@wunner.de> Signed-off-by: Andy Duan <fugang.duan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-09serial: fsl_lpuart: fix the typo: UARTCR1_PE -> UARTCTRL_PEAndy Duan1-1/+1
Fix the typo: UARTCR1_PE -> UARTCTRL_PE There have no function impacted since the macro define value is the same. Cc: Lukas Wunner <lukas@wunner.de> Signed-off-by: Andy Duan <fugang.duan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-10serial: fsl_lpuart: Remove the alias node dependenceVabhav Sharma1-2/+10
Numbering the ttyLPn space should not depend on the generic name "serial<n>". If don't add the alias node like:"serial0 = &lpuart0;", then lpuart will probe failed: [ 0.773410] fsl-lpuart 2950000.serial: failed to get alias id, errno -19 So remove the alias node dependence, and add the support for allocate the line port automatically. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-09-18tty: serial: lpuart: avoid leaking struct tty_structStefan Agner1-1/+2
The function tty_port_tty_get() gets a reference to the tty. Since the code is not using tty_port_tty_set(), the reference is kept even after closing the tty. Avoid using tty_port_tty_get() by directly access the tty instance. Since lpuart_start_rx_dma() is called from the .startup() and .set_termios() callback, it is safe to assume the tty instance is valid. Cc: stable@vger.kernel.org # v4.9+ Fixes: 5887ad43ee02 ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx") Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28serial: fsl_lpuart: Fix out-of-bounds access through DT aliasGeert Uytterhoeven1-0/+4
The lpuart_ports[] array is indexed using a value derived from the "serialN" alias in DT, which may lead to an out-of-bounds access. Fix this by adding a range check. Fixes: c9e2e946fb0ba5d2 ("tty: serial: add Freescale lpuart driver support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28serial: fsl_lpuart: Support common rs485 binding for RTS polarityLukas Wunner1-10/+3
Invoke the ->rs485_config callback on probe to set UARTMODEM_TXRTSPOL appropriately based on the UART's device properties. This implicitly sets UARTMODEM_TXRTSE if rs485 was enabled in the device properties, so drop the identical code from lpuart_probe(). It also fixes a bug: If an unsupported rs485 property was specified (rs485-rx-during-tx or rs485-rts-delay), the driver returns -ENOSYS without performing any cleanup, in particular without calling uart_remove_one_port() or clk_disable_unprepare(), thus leaking the uart_port. But with the invocation of ->rs485_config, the unsupported properties are now cleared in struct serial_rs485 and thus ignored. It therefore seems sufficient to just log an error instead of bailing out. Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28serial: Make retrieval of rs485 properties platform-agnosticLukas Wunner1-1/+1
Commit ef838a81dd4d ("serial: Add common rs485 device tree parsing function") consolidated retrieval of rs485 OF properties in a common helper function but did not #ifdef it to CONFIG_OF. The function is therefore included on ACPI platforms as well even though it's not used. On the other hand ACPI platforms with rs485 do exist (e.g. Siemens IOT2040) and they may leverage _DSD to store rs485 properties. Likewise, UART platform devices instantiated from an MFD should be able to specify rs485 properties. In fact, the tty subsystem maintainer had asked for a "generic" function during review of commit ef838a81dd4d: https://marc.info/?l=linux-serial&m=150143441725194&w=4 Thus, instead of constraining the helper to OF platforms, make it platform-agnostic by converting it to device_property_*() functions and renaming it accordingly. In imx.c, move the invocation of uart_get_rs485_mode() from serial_imx_probe_dt() to serial_imx_probe() so that it also gets called for non-OF devices. In omap-serial.c, move its invocation further up within serial_omap_probe_rs485() so that the RTS polarity can be overridden with the driver-specific "rs485-rts-active-high" property once we introduce a generic "rs485-rts-active-low" property. Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-21treewide: setup_timer() -> timer_setup()Kees Cook1-4/+3
This converts all remaining cases of the old setup_timer() API into using timer_setup(), where the callback argument is the structure already holding the struct timer_list. These should have no behavioral changes, since they just change which pointer is passed into the callback with the same available pointers after conversion. It handles the following examples, in addition to some other variations. Casting from unsigned long: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... setup_timer(&ptr->my_timer, my_callback, ptr); and forced object casts: void my_callback(struct something *ptr) { ... } ... setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr); become: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... timer_setup(&ptr->my_timer, my_callback, 0); Direct function assignments: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... ptr->my_timer.function = my_callback; have a temporary cast added, along with converting the args: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback; And finally, callbacks without a data assignment: void my_callback(unsigned long data) { ... } ... setup_timer(&ptr->my_timer, my_callback, 0); have their argument renamed to verify they're unused during conversion: void my_callback(struct timer_list *unused) { ... } ... timer_setup(&ptr->my_timer, my_callback, 0); The conversion is done with the following Coccinelle script: spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup.cocci @fix_address_of@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_timer, NULL, _E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E->_timer, NULL, (_cast_data)_E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E._timer, NULL, &_E); +timer_setup(&_E._timer, NULL, 0); | -setup_timer(&_E._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_timer, _callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | _E->_timer@_stl.function = _callback; | _E->_timer@_stl.function = &_callback; | _E->_timer@_stl.function = (_cast_func)_callback; | _E->_timer@_stl.function = (_cast_func)&_callback; | _E._timer@_stl.function = _callback; | _E._timer@_stl.function = &_callback; | _E._timer@_stl.function = (_cast_func)_callback; | _E._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_timer, _callback, 0); +setup_timer(&_E->_timer, _callback, (_cast_data)_E); | -timer_setup(&_E._timer, _callback, 0); +setup_timer(&_E._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_timer | -(_cast_data)&_E +&_E._timer | -_E +&_E->_timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_timer, _callback, 0); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0L); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0UL); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0L); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0UL); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_timer, _callback, 0); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0L); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0UL); +timer_setup(&_timer, _callback, 0); | -setup_timer(_timer, _callback, 0); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0L); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0UL); +timer_setup(_timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-28 03:50:58 +0000