| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
v2 changes:
from Thierry Reding:
* add "select TEGRA_SYSTEM_DMA" to Kconfig
from Grant Likely:
* add oneline description to header
* inline references to DRIVER_NAME
* inline references to BUSY_TIMEOUT
* open coded bytes_per_word()
* spi_readl/writel -> spi_tegra_readl/writel
* move transfer validation to spi_tegra_transfer
* don't request_mem_region iomem as platform bus does that for us
* __exit -> __devexit
v3 changes:
from Russell King:
* put request_mem_region back int
from Grant Likely:
* remove #undef DEBUG
* add SLINK_ to register bit defines
* remove unused bytes_per_word
* make spi_tegra_readl/writel static linine
* various refactoring for clarity
* mark err if BSY bit is not cleared after 1000 retries
* move spinlock to protect setting of RDY bit
* subsys_initcall -> module_init
v3 changes:
from Grant Likely:
* update spi_tegra to use PTR_ERRless dma API
v4 changes:
from Grant Likely:
* remove empty spi_tegra_cleanup fucntion
* allow device ids of -1
Signed-off-by: Erik Gilling <konkers@android.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>
spi: tegra: cleanups from upstream review
Change-Id: Icecf7e64efcb39de072a15234ba1faa4bad40d25
Signed-off-by: Erik Gilling <konkers@android.com>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
|
|
Add eSPI controller support based on the library code spi_fsl_lib.c.
The eSPI controller is newer controller 85xx/Pxxx devices supported.
There're some differences comparing to the SPI controller:
1. Has different register map and different bit definition
So leave the code operated the register to the driver code, not
the common code.
2. Support 4 dedicated chip selects
The software can't controll the chip selects directly, The SPCOM[CS]
field is used to select which chip selects is used, and the
SPCOM[TRANLEN] field is set to tell the controller how long the CS
signal need to be asserted. So the driver doesn't need the chipselect
related function when transfering data, just set corresponding register
fields to controll the chipseclect.
3. Different Transmit/Receive FIFO access register behavior
For SPI controller, the Tx/Rx FIFO access register can hold only
one character regardless of the character length, but for eSPI
controller, the register can hold 4 or 2 characters according to
the character lengths. Access the Tx/Rx FIFO access register of the
eSPI controller will shift out/in 4/2 characters one time. For SPI
subsystem, the command and data are put into different transfers, so
we need to combine all the transfers to one transfer in order to pass
the transfer to eSPI controller.
4. The max transaction length limitation
The max transaction length one time is limitted by the SPCOM[TRANSLEN]
field which is 0xFFFF. When used mkfs.ext2 command to create ext2
filesystem on the flash, the read length will exceed the max value of
the SPCOM[TRANSLEN] field.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Refactor the common code in file spi_fsl_spi.c to spi_fsl_lib.c used
by SPI/eSPI controller driver as a library, and leave the QE/CPM SPI
controller code in the SPI controller driver spi_fsl_spi.c.
Because the register map of the SPI controller and eSPI controller
is so different, also leave the code operated the register to the
driver code, not the common code.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This will pave the way to refactor out the common code which can be used
by the eSPI controller driver, and rename the SPI controller dirver to the
file spi_fsl_spi.c.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The original didn't specify Topcliff in the config prompt text.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Topcliff PCH is the platform controller hub that is going to be used
in Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. This patch
adds a driver for the SPI bus integrated into the Topcliff device.
Signed-off-by: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
i.MX51 comes with two eCSPI interfaces (that are quite different from
what was known before---the tried and tested Freescale way) and a CSPI
interface that is identical to the devices found on i.MX25 and i.MX35.
This patch is a merge of two very similar patches (by Jason Wang and Sascha
Hauer resp.) plus a (now hopefully correct) reimplementation of the
clock calculation.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This has the advantage not to need to much cpu_is_... macros. Still more
when imx51 support is added which has two different spi interfaces which
would introduce additional checks on the device id.
With this setup it's not possible for the compiler anymore to detect the
unused functions, so four additional kconfig symbols are introduced to
ifdef out the unneeded functions in the callback array and all these
functions are marked with __maybe_unused to suppress the corresponding
gcc warnings.
Comparing the driver footprint with and without the patch for a mx27
kernel yields:
add/remove: 2/0 grow/shrink: 2/0 up/down: 280/0 (280)
function old new delta
spi_imx_devtype - 192 +192
spi_imx_probe 980 1032 +52
spi_imx_devtype_data - 32 +32
spi_imx_setupxfer 276 280 +4
Later when the platform code is updated to use the platform ids, the
autodetection can be removed which will make the driver a bit smaller
again. (~60 Bytes in my test.)
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds an SPI master driver for the Cirrus EP93xx SPI controller found
in EP93xx chips.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Change dependency to ARCH_OMAP2PLUS to allow systems based on
omap24xx, omap34xx or omap44xx
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Conflicts:
arch/arm/plat-omap/Kconfig
|
|
Replace ARCH_OMAP34XX with ARCH_OMAP3
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Convert ARCH_OMAP24XX to ARCH_OMAP2
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
dw_spi_mmio is dependent on the clock framework. This marks it as such
in Kconfig.
Signed-off-by: Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Adds a memory-mapped I/O dw_spi platform device.
Signed-off-by: Jean-Hugues Deschenes <jean-hugues.deschenes@octasic.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add support for the QSPI controller found some on Freescale/Motorola
Coldfire MCUs.
Full duplex, active high cs, spi modes 0-3 and word sizes 8-16 bits are
supported. The hardware drives the MISO, MOSI and SCLK lines, but the chip
selects are managed via GPIO and must be configured by the board code.
The QSPI controller has an 80 byte buffer which allows us to transfer up to 16
words at a time. For transfers longer than 16 words, we split the buffer in
half so we can update in one half while the controller is operating on the
other half. Interrupt latencies then ultimately limits our sustained thru-put
to something less than half the maximum speed supported by the part.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds support for a SPI master driver for the
DaVinci series of SOCs
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi: spi_txx9.c: use resource_size()
spi: spi_sh_sci.c: use resource_size()
spi: spi_mpc8xxx.c: use resource_size()
spi: spi_bfin5xx.c: use resource_size()
spi: atmel_spi.c: use resource_size()
spi: Add s3c64xx SPI Controller driver
atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
spi_s3c24xx: add FIQ pseudo-DMA support
spi: controller driver for Designware SPI core
spidev: add proper section markers
spidev: use DECLARE_BITMAP instead of declaring the array
|
|
Each SPI controller has exactly one CS line and as such doesn't
provide for multi-cs. We implement a workaround to support
multi-cs by _not_ configuring the mux'ed CS pin for each SPI
controller. The CS mechanism is assumed to be fully machine
specific - the driver doesn't even assume some GPIO pin is used
to control the CS.
The driver selects between DMA and POLLING mode depending upon
the xfer size - DMA mode for xfers bigger than FIFO size, POLLING
mode otherwise.
The driver has been designed to be capable of running SoCs since
s3c64xx and till date, for that reason some of the register fields
have been passed via, SoC specific, platform data.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add pseudo-DMA by FIQ to the S3C24XX SPI driver. This allows the driver
to get DMA-like performance where there are either no free DMA channels or
when doing transfers that required both TX and RX data paths.
Since this patch requires the addition of an assembly file to hold the FIQ
code, we rename the module (instead of adding a rename of the .c file to
this patch). We expect most users are loading this via udev and thus
there should be no change to the userland configuration.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Driver for the Designware SPI core, it supports multipul interfaces like
PCI/APB etc. User can use "dw_apb_ssi_db.pdf" from Synopsys as HW
datasheet.
[randy.dunlap@oracle.com: fix build]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
spi: fix probe/remove section markings
Add OMAP spi100k driver
spi-imx: don't access struct device directly but use dev_get_platdata
spi-imx: Add mx25 support
spi-imx: use positive logic to distinguish cpu variants
spi-imx: correct check for platform_get_irq failing
ARM: NUC900: Add spi driver support for nuc900
spi: SuperH MSIOF SPI Master driver V2
spi: fix spidev compilation failure when VERBOSE is defined
spi/au1550_spi: fix setupxfer not to override cfg with zeros
spi/mpc8xxx: don't use __exit_p to wrap plat_mpc8xxx_spi_remove
spi/i.MX: fix broken error handling for gpio_request
spi/i.mx: drain MXC SPI transfer buffer when probing device
MAINTAINERS: add SPI co-maintainer.
spi/xilinx_spi: fix incorrect casting
spi/mpc52xx-spi: minor cleanups
xilinx_spi: add a platform driver using the xilinx_spi common module.
xilinx_spi: add support for the DS570 IP.
xilinx_spi: Switch to iomem functions and support little endian.
xilinx_spi: Split into of driver and generic part.
...
|
|
This change adds the OMAP SPI 100k driver created by
Fabrice Crohas <fcrohas@gmail.com>. This SPI bus is found on
OMAP7xx-series smartphones, and for many, the touchscreen is
attached to this bus.
The lion's share of the work was done by Fabrice on this driver --
I am merely porting it from the Linwizard project on his behalf.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch is V2 of SPI Master support for the SuperH MSIOF.
Full duplex, spi mode 0-3, active high cs, 3-wire and lsb
first should all be supported, but the driver has so far
only been tested with "mmc_spi".
The MSIOF hardware comes with 32-bit FIFOs for receive and
transmit, and this driver simply breaks the SPI messages
into FIFO-sized chunks. The MSIOF hardware manages the pins
for clock, receive and transmit (sck/miso/mosi), but the chip
select pin is managed by software and must be configured as
a regular GPIO pin by the board code.
Performance wise there is still room for improvement, but
on a Ecovec board with the built-in sh7724 MSIOF0 this driver
gets Mini-sd read speeds of about half a megabyte per second.
Future work include better clock setup and merging of 8-bit
transfers into 32-bit words to reduce interrupt load and
improve throughput.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
|
|
This patch adds in a platform device driver using the xilinx_spi common module.
Tested-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds in support for the DS570 IP.
It's register compatible with the DS464, but adds support for 8/16/32 SPI.
The 8/16/32 support is added by attaching callbacks reading/writing the
proper amount of data. To indicate to the driver which amount of bits
to use a new field is introduced in the platform data struct.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch changes the out_(be)(8|16|32) and in_(be)(8|16|32) calls to 32 bits ioread/iowrite.
The read and write function are attached to the internal struct as callbacks, callback
is selected depending on endianess.
This will also build on platforms not supporting the in/out calls for instance x86.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch splits the xilinx_spi driver into a generic part and a
OF driver part.
The reason for this is to later add in a platform driver as well.
Tested-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds QE buffer descriptors mode support for the
spi_mpc8xxx driver, and as a side effect we now support CPM1
and CPM2 SPI controllers.
That means that today we support almost all MPC SPI controllers:
- MPC834x-style controllers (support PIO mode only);
- CPM1 and CPM2 controllers (support DMA mode only);
- QE SPI controllers in CPU mode (PIO mode with shift quirks);
- QE SPI controllers in buffer descriptors (DMA) mode;
The only controller we don't currently support is a newer eSPI
(with a dedicated chip selects and a bit different registers map).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Adds support for the dedicated SPI device on the Freescale MPC5200(b)
SoC.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add SPI driver for Freescale STMP 3xxx-based boards
[dbrownell@users.sourceforge.net: cleanup sequence, spi_unregister_master]
Signed-off-by: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type
EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This makes the PL022 driver a default choice for any RealView and
Versatile boards plus the integrator IMPD1 which all contain the PL022
PrimeCell. This will make it a default choice if and only if a user
selects SPI support for their board.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds a SPI driver for the SPI controller found in the IBM/AMCC
4xx PowerPC's.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver is in a non working state at the moment and will be replaced
by a bitbang driver which can also handle the newer i.MX variants
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since we renamed the file, we might want to rename the file internals too.
Though we don't bother with changing platform driver name and platform
module alias. The stuff is legacy and hopefully we'll remove it soon.
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this patch we'll able to select spi_mpc83xx driver on the MPC86xx
platforms. Let the driver depend on FSL_SOC, so we don't have to worry
about Kconfig anymore.
Also remove the "experimental" dependency, the driver has been tested to
work on a various hardware, and surely not experimental anymore.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
|
|
This adds a driver for the ARM PL022 PrimeCell SSP/SPI
driver found in the U300 platforms as well as in some
ARM reference hardware, and in a modified version on the
Nomadik board.
Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data. Such SPI masters support:
- any number of bus instances (bus_num is the platform_device.id)
- any number of chipselects (one GPIO per spi_device)
- all four SPI_MODE values, and SPI_CS_HIGH
- i/o word sizes from 1 to 32 bits;
- devices configured as with any other spi_master controller
When configured using platform_data, this provides relatively low clock
rates. On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)
Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Magnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
