summaryrefslogtreecommitdiffstats
path: root/drivers/soc/ti
AgeCommit message (Collapse)AuthorFilesLines
2019-09-16Merge tag 'armsoc-drivers' of ↵Linus Torvalds1-2/+21
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Arnd Bergmann: "This contains driver changes that are tightly connected to SoC specific code. Aside from smaller cleanups and bug fixes, here is a list of the notable changes. New device drivers: - The Turris Mox router has a new "moxtet" bus driver for its on-board pluggable extension bus. The same platform also gains a firmware driver. - The Samsung Exynos family gains a new Chipid driver exporting using the soc device sysfs interface - A similar socinfo driver for Qualcomm Snapdragon chips. - A firmware driver for the NXP i.MX DSP IPC protocol using shared memory and a mailbox Other changes: - The i.MX reset controller driver now supports the NXP i.MX8MM chip - Amlogic SoC specific drivers gain support for the S905X3 and A311D chips - A rework of the TI Davinci framebuffer driver to allow important cleanups in the platform code - A couple of device drivers for removed ARM SoC platforms are removed. Most of the removals were picked up by other maintainers, this contains whatever was left" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits) bus: uniphier-system-bus: use devm_platform_ioremap_resource() soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access firmware: ti_sci: Allow for device shared and exclusive requests bus: imx-weim: remove incorrect __init annotations fbdev: remove w90x900/nuc900 platform drivers spi: remove w90x900 driver net: remove w90p910-ether driver net: remove ks8695 driver firmware: turris-mox-rwtm: Add sysfs documentation firmware: Add Turris Mox rWTM firmware driver dt-bindings: firmware: Document cznic,turris-mox-rwtm binding bus: moxtet: fix unsigned comparison to less than zero bus: moxtet: remove set but not used variable 'dummy' ARM: scoop: Use the right include dt-bindings: power: add Amlogic Everything-Else power domains bindings soc: amlogic: Add support for Everything-Else power domains controller fbdev: da8xx: use resource management for dma fbdev: da8xx-fb: drop a redundant if fbdev: da8xx-fb: use devm_platform_ioremap_resource() ...
2019-09-04soc: ti: ti_sci_pm_domains: Add support for exclusive and shared accessLokesh Vutla1-2/+21
TISCI protocol supports for enabling the device either with exclusive permissions for the requesting host or with sharing across the hosts. There are certain devices which are exclusive to Linux context and there are certain devices that are shared across different host contexts. So add support for getting this information from DT by increasing the power-domain cells to 2. For keeping the DT backward compatibility intact, defaulting the device permissions to set the exclusive flag set. In this case the power-domain-cells is 1. Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2019-08-13soc: ti: pm33xx: Make two symbols staticYueHaibing1-2/+2
Fix sparse warnings: drivers/soc/ti/pm33xx.c:144:27: warning: symbol 'rtc_wake_src' was not declared. Should it be static? drivers/soc/ti/pm33xx.c:160:5: warning: symbol 'am33xx_rtc_only_idle' was not declared. Should it be static? Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2019-08-13soc: ti: pm33xx: Fix static checker warningsKeerthy1-5/+10
The patch fixes a bunch of static checker warnings. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2019-07-19Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds1-0/+5
Pull ARM Devicetree updates from Olof Johansson: "We continue to see a lot of new material. I've highlighted some of it below, but there's been more beyond that as well. One of the sweeping changes is that many boards have seen their ARM Mali GPU devices added to device trees, since the DRM drivers have now been merged. So, with the caveat that I have surely missed several great contributions, here's a collection of the material this time around: New SoCs: - Mediatek mt8183 (4x Cortex-A73 + 4x Cortex-A53) - TI J721E (2x Cortex-A72 + 3x Cortex-R5F + 3 DSPs + MMA) - Amlogic G12B (4x Cortex-A73 + 2x Cortex-A53) New Boards / platforms: - Aspeed BMC support for a number of new server platforms - Kontron SMARC SoM (several i.MX6 versions) - Novtech's Meerkat96 (i.MX7) - ST Micro Avenger96 board - Hardkernel ODROID-N2 (Amlogic G12B) - Purism Librem5 devkit (i.MX8MQ) - Google Cheza (Qualcomm SDM845) - Qualcomm Dragonboard 845c (Qualcomm SDM845) - Hugsun X99 TV Box (Rockchip RK3399) - Khadas Edge/Edge-V/Captain (Rockchip RK3399) Updated / expanded boards and platforms: - Renesas r7s9210 has a lot of new peripherals added - Fixes and polish for Rockchip-based Chromebooks - Amlogic G12A has a lot of peripherals added - Nvidia Jetson Nano sees various fixes and improvements, and is now at feature parity with TX1" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (586 commits) ARM: dts: gemini: Set DIR-685 SPI CS as active low ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family ARM: dts: exynos: Move Mali400 GPU node to "/soc" ARM: dts: exynos: Fix imprecise abort on Mali GPU probe on Exynos4210 arm64: dts: qcom: qcs404: Add missing space for cooling-cells property arm64: dts: rockchip: Fix USB3 Type-C on rk3399-sapphire arm64: dts: rockchip: Update DWC3 modules on RK3399 SoCs arm64: dts: rockchip: enable rk3328 watchdog clock ARM: dts: rockchip: add display nodes for rk322x ARM: dts: rockchip: fix vop iommu-cells on rk322x arm64: dts: rockchip: Add support for Hugsun X99 TV Box arm64: dts: rockchip: Define values for the IPA governor for rock960 arm64: dts: rockchip: Fix multiple thermal zones conflict in rk3399.dtsi arm64: dts: rockchip: add core dtsi file for RK3399Pro SoCs arm64: dts: rockchip: improve rk3328-roc-cc rgmii performance. Revert "ARM: dts: rockchip: set PWM delay backlight settings for Minnie" ARM: dts: rockchip: Configure BT_DEV_WAKE in on rk3288-veyron arm64: dts: qcom: sdm845-cheza: add initial cheza dt ARM: dts: msm8974-FP2: Add vibration motor ...
2019-07-19Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds1-0/+1
Pull ARM SoC platform updates from Olof Johansson: "SoC platform changes. Main theme this merge window: - The Netx platform (Netx 100/500) platform is removed by Linus Walleij-- the SoC doesn't have active maintainers with hardware, and in discussions with the vendor the agreement was that it's OK to remove. - Russell King has a series of patches that cleans up and refactors SA1101 and RiscPC support" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits) ARM: stm32: use "depends on" instead of "if" after prompt ARM: sa1100: convert to common clock framework ARM: exynos: Cleanup cppcheck shifting warning ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view ARM: exynos: Only build MCPM support if used arm: add missing include platform-data/atmel.h ARM: davinci: Use GPIO lookup table for DA850 LEDs ARM: OMAP2: drop explicit assembler architecture ARM: use arch_extension directive instead of arch argument ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB ARM: riscpc: enable chained scatterlist support ARM: riscpc: reduce IRQ handling code ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc ARM: riscpc: parse video information from tagged list ARM: riscpc: add ecard quirk for Atomwide 3port serial card MAINTAINERS: mvebu: Add git entry soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh ARM: OMAP2+: Make some variables static ...
2019-07-01soc: ti: fix irq-ti-sci link errorArnd Bergmann1-2/+2
The irqchip driver depends on the SoC specific driver, but we want to be able to compile-test it elsewhere: WARNING: unmet direct dependencies detected for TI_SCI_INTA_MSI_DOMAIN Depends on [n]: SOC_TI [=n] Selected by [y]: - TI_SCI_INTA_IRQCHIP [=y] && TI_SCI_PROTOCOL [=y] drivers/irqchip/irq-ti-sci-inta.o: In function `ti_sci_inta_irq_domain_probe': irq-ti-sci-inta.c:(.text+0x204): undefined reference to `ti_sci_inta_msi_create_irq_domain' Rearrange the Kconfig and Makefile so we build the soc driver whenever its users are there, regardless of the SOC_TI option. Fixes: 49b323157bf1 ("soc: ti: Add MSI domain bus support for Interrupt Aggregator") Fixes: f011df6179bd ("irqchip/ti-sci-inta: Add msi domain support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2019-06-19Merge tag 'ti-k3-soc-for-v5.3' of ↵Olof Johansson1-0/+5
git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt Texas Instruments K3 SoC family changes for 5.3 - Add support for the new J721e SoC, includes basic peripherals needed for booting up the device - New peripheral support added for AM654x: * TI SCI irqchip * GPIO * MCU SRAM * R5Fs * MSMC RAM * SERDES and PCIe * tag 'ti-k3-soc-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux: (26 commits) arm64: dts: ti: k3-j721e: Add the MCU SRAM node arm64: dts: ti: k3-j721e: Add interrupt controllers in wakeup domain arm64: dts: ti: k3-j721e: Add interrupt controllers in main domain arm64: dts: ti: k3-j721e-main: Add Main NavSS Interrupt controller node arm64: defconfig: Enable TI's J721E SoC platform arm64: dts: ti: Add support for J721E Common Processor Board soc: ti: Add Support for J721E SoC config option arm64: dts: ti: Add Support for J721E SoC dt-bindings: serial: 8250_omap: Add compatible for J721E UART controller dt-bindings: arm: ti: Add bindings for J721E SoC arm64: dts: ti: am654-base-board: Disable SERDES and PCIe arm64: dts: k3-am6: Add PCIe Endpoint DT node arm64: dts: k3-am6: Add PCIe Root Complex DT node arm64: dts: k3-am6: Add SERDES DT node arm64: dts: k3-am6: Add mux-controller DT node required for muxing SERDES arm64: dts: k3-am6: Add "socionext,synquacer-pre-its" property to gic_its arm64: dts: ti: k3-am65: Add MSMC RAM ranges in interconnect node arm64: dts: ti: k3-am65: Add R5F ranges in interconnect nodes arm64: dts: ti: k3-am65-mcu: Add the MCU RAM node arm64: dts: ti: k3-am65: Add MCU SRAM ranges in interconnect nodes ... Signed-off-by: Olof Johansson <olof@lixom.net>
2019-06-19soc: ti: Add Support for J721E SoC config optionNishanth Menon1-0/+5
Add option to build J721E SoC specific components Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-06-17Merge tag 'omap-for-v5.3/soc-signed' of ↵Olof Johansson1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc ti-sysc soc changes for v5.3 Just two changes to make few platform data functions static, and to call dev_info() if am437x is suspending to RTC-only mode. We want to see this in case of issues as it depends on the board wiring for things like DDR memory. * tag 'omap-for-v5.3/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh ARM: OMAP2+: Make some variables static Signed-off-by: Olof Johansson <olof@lixom.net>
2019-06-10soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in ↵Keerthy1-0/+1
self-refresh Currently there is no way to distinguish if the SoC entered DS0 mode or the RTC only mode. Hence add a print before entering the RTC only mode. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174Thomas Gleixner5-45/+5
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 655 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Richard Fontana <rfontana@redhat.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner1-0/+1
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-19Merge branch 'irq-urgent-for-linus' of ↵Linus Torvalds3-0/+153
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull IRQ chip updates from Ingo Molnar: "A late irqchips update: - New TI INTR/INTA set of drivers - Rewrite of the stm32mp1-exti driver as a platform driver - Update the IOMMU MSI mapping API to be RT friendly - A number of cleanups and other low impact fixes" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits) iommu/dma-iommu: Remove iommu_dma_map_msi_msg() irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg() irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg() irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg() irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg() iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts genirq/msi: Add a new field in msi_desc to store an IOMMU cookie arm64: arch_k3: Enable interrupt controller drivers irqchip/ti-sci-inta: Add msi domain support soc: ti: Add MSI domain bus support for Interrupt Aggregator irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings irqchip/ti-sci-intr: Add support for Interrupt Router driver dt-bindings: irqchip: Introduce TISCI Interrupt router bindings gpio: thunderx: Use the default parent apis for {request,release}_resources genirq: Introduce irq_chip_{request,release}_resource_parent() apis firmware: ti_sci: Add helper apis to manage resources firmware: ti_sci: Add RM mapping table for am654 firmware: ti_sci: Add support for IRQ management firmware: ti_sci: Add support for RM core ops ...
2019-05-01soc: ti: Add MSI domain bus support for Interrupt AggregatorLokesh Vutla3-0/+153
With the system coprocessor managing the range allocation of the inputs to Interrupt Aggregator, it is difficult to represent the device IRQs from DT. The suggestion is to use MSI in such cases where devices wants to allocate and group interrupts dynamically. Create a MSI domain bus layer that allocates and frees MSIs for a device. APIs that are implemented: - ti_sci_inta_msi_create_irq_domain() that creates a MSI domain - ti_sci_inta_msi_domain_alloc_irqs() that creates MSIs for the specified device and resource. - ti_sci_inta_msi_domain_free_irqs() frees the irqs attached to the device. - ti_sci_inta_msi_get_virq() for getting the virq attached to a specific event. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-04-08soc: ti: pm33xx: AM437X: Add rtc_only with ddr in self-refresh supportKeerthy2-11/+185
During RTC-only suspend, power is lost to the wkup domain, so we need to save and restore the state of that domain. We also need to store some information within the RTC registers so that u-boot can do the right thing at powerup. The state is entered by getting the RTC to bring the pmic_power_en line low which will instruct the PMIC to disable the appropriate power rails after putting DDR into self-refresh mode. To bring pmic_power_en low, we need to get an ALARM2 event. Since we are running from SRAM at that point, it means calculating what the next second is (via ASM) and programming that into the RTC. This patch also adds support for wake up source detection. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2019-04-08soc: ti: pm33xx: Move the am33xx_push_sram_idle to the topKeerthy1-50/+50
Move the am33xx_push_sram_idle function to the top as a preparation for rtc+ddr mode as the function will be called by multiple functions currently present before it. No functional changes. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2019-01-30soc: ti: knav_dma: Use proper enum in pktdma_init_chanNathan Chancellor1-1/+1
Clang warns when one enumerated type is implicitly converted to another: drivers/soc/ti/knav_dma.c:601:20: warning: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Wenum-conversion] chan->direction = DMA_NONE; ~ ^~~~~~~~ 1 warning generated. While DMA_NONE and DMA_TRANS_NONE have different values, there is no functional change because direction is never checked against DMA_NONE, only against DMA_MEM_TO_DEV and DMA_DEV_TO_MEM. Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2018-11-19soc: ti: wkup_m3: Add PRCM int16 as the wake up sourceKeerthy1-0/+1
Add PRCM int16 as the wake up source. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-11-02soc: ti: QMSS: Fix usage of irq_set_affinity_hintMarc Zyngier3-14/+22
The Keystone QMSS driver is pretty damaged, in the sense that it does things like this: irq_set_affinity_hint(irq, to_cpumask(&cpu_map)); where cpu_map is a local variable. As we leave the function, this will point to nowhere-land, and things will end-up badly. Instead, let's use a proper cpumask that gets allocated, giving the driver a chance to actually work with things like irqbalance as well as have a hypothetical 64bit future. Cc: stable@vger.kernel.org Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2018-10-29Merge tag 'armsoc-drivers' of ↵Linus Torvalds2-5/+5
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Arnd Bergmann: "The most noteworthy SoC driver changes this time include: - The TEE subsystem gains an in-kernel interface to access the TEE from device drivers. - The reset controller subsystem gains a driver for the Qualcomm Snapdragon 845 Power Domain Controller. - The Xilinx Zynq platform now has a firmware interface for its platform management unit. This contains a firmware "ioctl" interface that was a little controversial at first, but the version we merged solved that by not exposing arbitrary firmware calls to user space. - The Amlogic Meson platform gains a "canvas" driver that is used for video processing and shared between different high-level drivers. The rest is more of the usual, mostly related to SoC specific power management support and core drivers in drivers/soc: - Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new features related to power and reset control. - The Mediatek mt8183 and mt6765 SoC platforms gain support for their respective power management chips. - A new driver for NXP i.MX8, which need a firmware interface for power management. - The SCPI firmware interface now contains support estimating power usage of performance states - The NVIDIA Tegra "pmc" driver gains a few new features, in particular a pinctrl interface for configuring the pads. - Lots of small changes for Qualcomm, in particular the "smem" device driver. - Some cleanups for the TI OMAP series related to their sysc controller. Additional cleanups and bugfixes in SoC specific drivers include the Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits) firmware: tegra: bpmp: Implement suspend/resume support drivers: clk: Add ZynqMP clock driver dt-bindings: clock: Add bindings for ZynqMP clock driver firmware: xilinx: Add zynqmp IOCTL API for device control Documentation: xilinx: Add documentation for eemi APIs MAINTAINERS: imx: include drivers/firmware/imx path firmware: imx: add misc svc support firmware: imx: add SCU firmware driver support reset: Fix potential use-after-free in __of_reset_control_get() dt-bindings: arm: fsl: add scu binding doc soc: fsl: qbman: add interrupt coalesce changing APIs soc: fsl: bman_portals: defer probe after bman's probe soc: fsl: qbman: Use last response to determine valid bit soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers soc: fsl: qbman: Check if CPU is offline when initializing portals reset: qcom: PDC Global (Power Domain Controller) reset controller dt-bindings: reset: Add PDC Global binding for SDM845 SoCs reset: Grammar s/more then once/more than once/ bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS ...
2018-10-04soc: Convert to using %pOFn instead of device_node.nameRob Herring2-8/+8
In preparation to remove the node name pointer from struct device_node, convert printf users to use the %pOFn format specifier. Cc: Li Yang <leoyang.li@nxp.com> Cc: David Brown <david.brown@linaro.org> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Santosh Shilimkar <ssantosh@kernel.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-soc@vger.kernel.org Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Qiang Zhao <qiang.zhao@nxp.com> Acked-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org>
2018-09-24soc: ti: fix spelling mistake "instace" -> "instance"Colin King2-5/+5
Trivial fix to spelling mistake in dev_err messages and comments Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2018-08-23Merge tag 'armsoc-dt' of ↵Linus Torvalds1-0/+14
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM device-tree updates from Olof Johansson: "Business as usual -- the bulk of our changes are to devicetree files with new hardware support, new SoCs and platforms, and new board types. New SoCs/platforms: - Raspberry Pi Compute Module (CM1) and IO board - i.MX6SSL from NXP - Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and PLC interfaces - TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5 controllers, communication and PRU subsystem and lots of other interfaces (PCIe, USB3, etc). New boards and systems: - Several Atmel at91-based boards from Laird - Marvell Armada388-based Helios4 board from SolidRun - Samsung Aires-based phones (s5pv210) - Allwinner A64-based Pinebook laptop In addition to the above, there's the usual amount of new devices described on existing platforms, fixes and tweaks and new minor variants of boards/platforms" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits) arm64: dts: sdm845: Add tsens nodes arm64: dts: msm8996: thermal: Initialise via DT and add second controller arm64: dts: sprd: Add one suspend timer arm64: dts: sprd: Add SC27XX ADC device arm64: dts: sprd: Add SC27XX eFuse device arm64: dts: sprd: Add SC27XX vibrator device arm64: dts: sprd: Add SC27XX breathing light controller device arm64: dts: meson-axg: add spdif-dit codec arm64: dts: meson-axg: add lineout codec arm64: dts: meson-axg: add linein codec arm64: dts: meson-axg: add tdm interfaces arm64: dts: meson-axg: add tdmout formatters arm64: dts: meson-axg: add tdmin formatters arm64: dts: meson-axg: add spdifout arm64: dts: rockchip: add led support for Firefly-RK3399 arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399 arm64: dts: rockchip: add power button support for Firefly-RK3399 ARM: dts: aspeed: Add coprocessor interrupt controller arm64: dts: meson-axg: add audio arb reset controller arm64: dts: meson-axg: add usb power regulator ...
2018-08-23Merge tag 'armsoc-drivers' of ↵Linus Torvalds1-0/+76
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "Some of the larger changes this merge window: - Removal of drivers for Exynos5440, a Samsung SoC that never saw widespread use. - Uniphier support for USB3 and SPI reset handling - Syste control and SRAM drivers and bindings for Allwinner platforms - Qualcomm AOSS (Always-on subsystem) reset controller drivers - Raspberry Pi hwmon driver for voltage - Mediatek pwrap (pmic) support for MT6797 SoC" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits) drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests soc: fsl: cleanup Kconfig menu soc: fsl: dpio: Convert DPIO documentation to .rst staging: fsl-mc: Remove remaining files staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl staging: fsl-dpaa2: eth: move generic FD defines to DPIO soc: fsl: qe: gpio: Add qe_gpio_set_multiple usb: host: exynos: Remove support for Exynos5440 clk: samsung: Remove support for Exynos5440 soc: sunxi: Add the A13, A23 and H3 system control compatibles reset: uniphier: add reset control support for SPI cpufreq: exynos: Remove support for Exynos5440 ata: ahci-platform: Remove support for Exynos5440 soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs soc: mediatek: pwrap: fix cipher init setting error dt-bindings: pwrap: mediatek: add pwrap support for MT6797 reset: uniphier: add USB3 core reset control dt-bindings: reset: uniphier: add USB3 core reset support ...
2018-07-18soc: ti: Add Support for AM654 SoC config optionNishanth Menon1-0/+14
Add option to build AM6 SoC specific components Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Benjamin Fair <b-fair@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-07-09ARM: OMAP2+: sleep33/43xx: Add RTC-Mode supportKeerthy1-0/+1
Add support for RTC mode to low level suspend code. This includes providing the rtc base address for the assembly code to configuring the PMIC_PWR_EN line late in suspend to enter RTC+DDR mode. Note: This patch also fold in left out space parameter for am33xx_emif_sram_table and am43xx_emif_sram_table Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-07-09ARM: OMAP2+: sleep33/43xx: Make sleep actions configurableDave Gerlach1-1/+14
Add an argument to the sleep33xx and sleep43xx code to allow us to set flags to determine which portions of the code get called in order to use the same code for multiple power saving modes. This patch allows us to decide whether or not we flush and disable caches, save EMIF context, put the memory into self refresh and disable the EMIF, and/or invoke the wkup_m3 when entering into WFI. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-07-06soc: ti: wkup_m3_ipc: mark PM functions as __maybe_unusedArnd Bergmann1-6/+2
Everyone gets these #ifdefs wrong, leading to another warning here: drivers/soc/ti/wkup_m3_ipc.c:547:12: error: 'wkup_m3_ipc_resume' defined but not used [-Werror=unused-function] static int wkup_m3_ipc_resume(struct device *dev) drivers/soc/ti/wkup_m3_ipc.c:539:12: error: 'wkup_m3_ipc_suspend' defined but not used [-Werror=unused-function] static int wkup_m3_ipc_suspend(struct device *dev) The easiest way to get it right is to remove all the #ifdefs and let the compiler drop the unused functions silently after we mark them as __maybe_unused. Fixes: 7a872b6fb7fd ("soc: ti: wkup_m3_ipc: Add rtc_only with ddr in self refresh mode support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2018-07-04soc: ti: wkup_m3_ipc: Add wkup_m3_request_wake_srcDave Gerlach1-0/+39
Add wkup_m3_request_wake_src to allow users to get the name of the wakeup source after a DeepSleep or Standby transition. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2018-07-04soc: ti: wkup_m3_ipc: Add rtc_only with ddr in self refresh mode supportKeerthy1-0/+41
Adds rtc_only support. This needs resume function to shutdown and reboot the m3. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2018-06-12Merge tag 'overflow-v4.18-rc1-part2' of ↵Linus Torvalds1-3/+3
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull more overflow updates from Kees Cook: "The rest of the overflow changes for v4.18-rc1. This includes the explicit overflow fixes from Silvio, further struct_size() conversions from Matthew, and a bug fix from Dan. But the bulk of it is the treewide conversions to use either the 2-factor argument allocators (e.g. kmalloc(a * b, ...) into kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a * b) into vmalloc(array_size(a, b)). Coccinelle was fighting me on several fronts, so I've done a bunch of manual whitespace updates in the patches as well. Summary: - Error path bug fix for overflow tests (Dan) - Additional struct_size() conversions (Matthew, Kees) - Explicitly reported overflow fixes (Silvio, Kees) - Add missing kvcalloc() function (Kees) - Treewide conversions of allocators to use either 2-factor argument variant when available, or array_size() and array3_size() as needed (Kees)" * tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits) treewide: Use array_size in f2fs_kvzalloc() treewide: Use array_size() in f2fs_kzalloc() treewide: Use array_size() in f2fs_kmalloc() treewide: Use array_size() in sock_kmalloc() treewide: Use array_size() in kvzalloc_node() treewide: Use array_size() in vzalloc_node() treewide: Use array_size() in vzalloc() treewide: Use array_size() in vmalloc() treewide: devm_kzalloc() -> devm_kcalloc() treewide: devm_kmalloc() -> devm_kmalloc_array() treewide: kvzalloc() -> kvcalloc() treewide: kvmalloc() -> kvmalloc_array() treewide: kzalloc_node() -> kcalloc_node() treewide: kzalloc() -> kcalloc() treewide: kmalloc() -> kmalloc_array() mm: Introduce kvcalloc() video: uvesafb: Fix integer overflow in allocation UBIFS: Fix potential integer overflow in allocation leds: Use struct_size() in allocation Convert intel uncore to struct_size ...
2018-06-12treewide: devm_kzalloc() -> devm_kcalloc()Kees Cook1-3/+3
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-11Merge tag 'armsoc-drivers' of ↵Linus Torvalds2-26/+48
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "This contains platform-related driver updates for ARM and ARM64. Highlights: - ARM SCMI (System Control & Management Interface) driver cleanups - Hisilicon support for LPC bus w/ ACPI - Reset driver updates for several platforms: Uniphier, - Rockchip power domain bindings and hardware descriptions for several SoCs. - Tegra memory controller reset improvements" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (59 commits) ARM: tegra: fix compile-testing PCI host driver soc: rockchip: power-domain: add power domain support for px30 dt-bindings: power: add binding for px30 power domains dt-bindings: power: add PX30 SoCs header for power-domain soc: rockchip: power-domain: add power domain support for rk3228 dt-bindings: power: add binding for rk3228 power domains dt-bindings: power: add RK3228 SoCs header for power-domain soc: rockchip: power-domain: add power domain support for rk3128 dt-bindings: power: add binding for rk3128 power domains dt-bindings: power: add RK3128 SoCs header for power-domain soc: rockchip: power-domain: add power domain support for rk3036 dt-bindings: power: add binding for rk3036 power domains dt-bindings: power: add RK3036 SoCs header for power-domain dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions memory: tegra: Remove Tegra114 SATA and AFI reset definitions memory: tegra: Register SMMU after MC driver became ready soc: mediatek: remove unneeded semicolon soc: mediatek: add a fixed wait for SRAM stable soc: mediatek: introduce a CAPS flag for scp_domain_data soc: mediatek: reuse regmap_read_poll_timeout helpers ...
2018-04-20soc: ti: knav_qmss: Use percpu instead atomic for stats counterVasyl Gomonovych2-26/+48
Hwqueue has collect statistics in heavy use queue_pop/queu_push functions for cache efficiency and make push/pop faster use percpu variables. For performance reasons, driver should keep descriptor in software handler as short as possible and quickly return it back to hardware queue. Descriptors coming into driver from hardware after pop and return back by push to reduce descriptor lifetime in driver collect statistics on percpu. Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2018-04-18soc: ti: K2G: provide APIs to support driver probe deferralMurali Karicheri2-0/+16
This patch provide APIs to allow client drivers to support probe deferral. On K2G SoC, devices can be probed only after the ti_sci_pm_domains driver is probed and ready. As drivers may get probed at different order, any driver that depends on knav dma and qmss drivers, for example netcp network driver, needs to defer probe until knav devices are probed and ready to service. To do this, add an API to query the device ready status from the knav dma and qmss devices. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-18soc: ti: K2G: enhancement to support QMSS in K2G NAVSSMurali Karicheri2-22/+74
Navigator Subsystem (NAVSS) available on K2G SoC has a cut down version of QMSS with less number of queues, internal linking ram with lesser number of buffers etc. It doesn't have status and explicit push register space as in QMSS available on other K2 SoCs. So define reg indices specific to QMSS on K2G. This patch introduces "ti,66ak2g-navss-qm" compatibility to identify QMSS on K2G NAVSS and to customize the dts handling code. Per Device manual, descriptors with index less than or equal to regions0_size is in region 0 in the case of K2 QMSS where as for QMSS on K2G, descriptors with index less than regions0_size is in region 0. So update the size accordingly in the regions0_size bits of the linking ram size 0 register. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27soc: ti: Add pm33xx driver for basic suspend supportDave Gerlach3-0/+359
AM335x and AM437x support various low power modes as documented in section 8.1.4.3 of the AM335x Technical Reference Manual and section 6.4.3 of the AM437x Technical Reference Manual. DeepSleep0 mode offers the lowest power mode with limited wakeup sources without a system reboot and is mapped as the suspend state in the kernel. In this state, MPU and PER domains are turned off with the internal RAM held in retention to facilitate the resume process. As part of the boot process, the assembly code is copied over to OCMCRAM so it can be executed to turn of the EMIF and put DDR into self refresh. Both platforms have a Cortex-M3 (WKUP_M3) which assists the MPU in DeepSleep0 entry and exit. WKUP_M3 takes care of the clockdomain and powerdomain transitions based on the intended low power state. MPU needs to load the appropriate WKUP_M3 binary onto the WKUP_M3 memory space before it can leverage any of the PM features like DeepSleep. This loading is handled by the remoteproc driver wkup_m3_rproc. Communication with the WKUP_M3 is handled by a wkup_m3_ipc driver that exposes the specific PM functionality to be used the PM code. In the current implementation when the suspend process is initiated, MPU interrupts the WKUP_M3 to let it know about the intent of entering DeepSleep0 and waits for an ACK. When the ACK is received MPU continues with its suspend process to suspend all the drivers and then jumps to assembly in OCMC RAM. The assembly code puts the external RAM in self-refresh mode, gates the MPU clock, and then finally executes the WFI instruction. Execution of the WFI instruction with MPU clock gated triggers another interrupt to the WKUP_M3 which then continues with the power down sequence wherein the clockdomain and powerdomain transition takes place. As part of the sleep sequence, WKUP_M3 unmasks the interrupt lines for the wakeup sources. WFI execution on WKUP_M3 causes the hardware to disable the main oscillator of the SoC and from here system remains in sleep state until a wake source brings the system into resume path. When a wakeup event occurs, WKUP_M3 starts the power-up sequence by switching on the power domains and finally enabling the clock to MPU. Since the MPU gets powered down as part of the sleep sequence in the resume path ROM code starts executing. The ROM code detects a wakeup from sleep and then jumps to the resume location in OCMC which was populated in one of the IPC registers as part of the suspend sequence. Code is based on work by Vaibhav Bedia. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-12-16soc: ti: fix max dup length for kstrndupMa Shimiao1-2/+2
If source string longer than max, kstrndup will alloc max+1 space. So, we should make sure the result will not over limit. Signed-off-by: Ma Shimiao <mashimiao.fnst@cn.fujitsu.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman1-0/+1
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-21soc: ti: knav: Add a NULL pointer check for kdev in knav_pool_createKeerthy1-0/+3
knav_pool_create is an exported function. In the event of a call before knav_queue_probe, we encounter a NULL pointer dereference in the following line. Hence return -EPROBE_DEFER to the caller till the kdev pointer is non-NULL. Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-08-18soc: ti: ti_sci_pm_domains: Populate name for genpdDave Gerlach1-0/+2
Commit b6a1d093f96b ("PM / Domains: Extend generic power domain debugfs") now creates a debugfs directory for each genpd based on the name of the genpd. Currently no name is given to the genpd created by ti_sci_pm_domains driver so because of this we see a NULL pointer dereferences when it is accessed on boot when the debugfs entry creation is attempted. Give the genpd a name before registering it to avoid this. Fixes: 52835d59fc6c ("soc: ti: Add ti_sci_pm_domains driver") Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-05-11net: ethernet: ti: netcp_core: return error while dma channel open issueIvan Khoronzhuk1-1/+1
Fix error path while dma open channel issue. Also, no need to check output on NULL if it's never returned. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-24soc: pm-domain: Fix the mangled urlsSantosh Shilimkar1-1/+1
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2017-04-04soc: ti: Add ti_sci_pm_domains driverDave Gerlach3-0/+215
Introduce a ti_sci_pm_domains driver to act as a generic pm domain provider to allow each device to attach and associate it's ti-sci-id so that it can be controlled through the TI SCI protocol. This driver implements a simple genpd where each device node has a phandle to the power domain node and also must provide an index which represents the ID to be passed with TI SCI representing the device using a single phandle cell. The driver manually parses the phandle to get the cell value. Through this interface the genpd dev_ops start and stop hooks will use TI SCI to turn on and off each device as determined by pm_runtime usage. Reviewed-by: Kevin Hilman <khilman@baylibre.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2017-02-23Merge tag 'armsoc-drivers' of ↵Linus Torvalds4-33/+13
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Arnd Bergmann: "Driver updates for ARM SoCs. A handful of driver changes this time around. The larger changes are: - Reset drivers for hi3660 and zx2967 - AHCI driver for Davinci, acked by Tejun and brought in here due to platform dependencies - Cleanups of atmel-ebi (External Bus Interface) - Tweaks for Rockchip GRF (General Register File) usage (kitchensink misc register range on the SoCs) - PM domains changes for support of two new ZTE SoCs (zx296718 and zx2967)" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits) soc: samsung: pmu: Add register defines for pad retention control reset: make zx2967 explicitly non-modular reset: core: fix reset_control_put soc: samsung: pm_domains: Read domain name from the new label property soc: samsung: pm_domains: Remove message about failed memory allocation soc: samsung: pm_domains: Remove unused name field soc: samsung: pm_domains: Use full names in subdomains registration log sata: ahci-da850: un-hardcode the MPY bits sata: ahci-da850: add a workaround for controller instability sata: ahci: export ahci_do_hardreset() locally sata: ahci-da850: implement a workaround for the softreset quirk sata: ahci-da850: add device tree match table sata: ahci-da850: get the sata clock using a connection id soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register memory: atmel-ebi: Enable the SMC clock if specified soc: samsung: pmu: Remove unused and duplicated defines memory: atmel-ebi: Properly handle multiple reference to the same CS memory: atmel-ebi: Fix the test to enable generic SMC logic soc: samsung: pm_domains: Add new Exynos5433 compatible soc: samsung: pmu: Add dummy support for Exynos5433 SoC ...
2017-01-29Merge tag 'omap-for-v4.11/drivers-signed' of ↵Olof Johansson1-2/+0
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers Just a single wkup_m3_ipc clean-up for v4.11 merge window. We don't currently have anything else for drivers/soc to merge, but I'd expect that to change as soon as we can start moving PM code into drivers with the recently posted SRAM changes. Anyways, sent as a separate pull request to make it easy to group the ARM SoC pull requests. * tag 'omap-for-v4.11/drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: soc: ti: wkup_m3_ipc: Drop wait from wkup_m3_rproc_boot_thread Signed-off-by: Olof Johansson <olof@lixom.net>
2017-01-12soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()Wei Yongjun1-0/+1
Fix to return a negative error code from the kthread_run() error handling case instead of 0, as done elsewhere in this function. Fixes: cdd5de500b2c ("soc: ti: Add wkup_m3_ipc driver") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-01-06soc: ti: knav: cleanup includes and sort header filesMurali Karicheri2-29/+11
This patch cleanup the code to remove unnecessary header files and also sort the header files. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
2017-01-06soc: ti: knav_dma: fix typos in trace messageMurali Karicheri1-2/+2
This patch fixes some typos in the trace message Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-18 17:06:20 +0000