| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The ifc6410 firmware always enters the kernel in ARM state from
deep idle. Use the cpu_resume_arm() wrapper instead of
cpu_resume() to property switch into the THUMB2 state when we
wake up from idle.
This fixes a problem reported by Kevin Hilman on next-20150601
where the ifc6410 fails to boot a THUMB2 kernel because the
platform's firmware always enters the kernel in ARM mode from
deep idle states.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
SPM is a hardware block that controls the peripheral logic surrounding
the application cores (cpu/l$). When the core executes WFI instruction,
the SPM takes over the putting the core in low power state as
configured. The wake up for the SPM is an interrupt at the GIC, which
then completes the rest of low power mode sequence and brings the core
out of low power mode.
The SPM has a set of control registers that configure the SPMs
individually based on the type of the core and the runtime conditions.
SPM is a finite state machine block to which a sequence is provided and
it interprets the bytes and executes them in sequence. Each low power
mode that the core can enter into is provided to the SPM as a sequence.
Configure the SPM to set the core (cpu or L2) into its low power mode,
the index of the first command in the sequence is set in the SPM_CTL
register. When the core executes ARM wfi instruction, it triggers the
SPM state machine to start executing from that index. The SPM state
machine waits until the interrupt occurs and starts executing the rest
of the sequence until it hits the end of the sequence. The end of the
sequence jumps the core out of its low power mode.
Add support for an idle driver to set up the SPM to place the core in
Standby or Standalone power collapse mode when the core is idle.
Based on work by: Mahesh Sivasubramanian <msivasub@codeaurora.org>,
Ai Li <ali@codeaurora.org>, Praveen Chidambaram <pchidamb@codeaurora.org>
Original tree available at -
git://codeaurora.org/quic/la/kernel/msm-3.10.git
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
|
|
This patch adds automatic configuration for the ADM CRCI muxing required to
support DMA operations for GSBI clients. The GSBI mode and instance determine
the correct TCSR ADM CRCI MUX value that must be programmed so that the DMA
works properly.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
since commit 31964ffebbb9 ("tty: serial: msm: Remove direct access to GSBI")'
serial hangs if earlyprintk are enabled.
This hang is noticed only when the GSBI driver is probed and all the
earlyprintks before gsbi probe are seen on the console.
The reason why it hangs is because GSBI driver disables hclk in its
probe function without realizing that the serial IP might be in use by
a bootconsole. As gsbi driver disables the clock in probe the
bootconsole locks up.
Turning off hclk's could be dangerous if there are system components
like earlyprintk using the hclk.
This patch fixes the issue by delegating the clock management to
probe and remove functions in gsbi rather than disabling the clock in probe.
More detailed problem description can be found here:
http://www.spinics.net/lists/linux-arm-msm/msg10589.html
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The match tables must be zero-terminated, and Kbuild now helpfully
fails to link the kernel if that isn't the case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The GSBI (General Serial Bus Interface) driver controls the overarching
configuration of the shared serial bus infrastructure on APQ8064, IPQ8064, and
earlier QCOM processors. The GSBI supports UART, I2C, SPI, and UIM
functionality in various combinations.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
|
