| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The IO command size is 128 bytes for these new controllers as opposed to 64
for the old 8001 controller.
The Adaptec out-of-tree driver did this correctly. After comparing the two
this turned out to be the crucial difference.
So don't hardcode the IO command size, instead use pm8001_ha->iomb_size as
that is the correct value for both old and new controllers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Anand Kumar Santhanam <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We want ppc64 to be able to select between optimised assembly
checksum routines in big endian and the generic lib/checksum.c
routines in little endian.
The lpfc driver is forcing CONFIG_GENERIC_CSUM on which means
we are unable to make the decision to enable it in the arch
Kconfig. If the option exists it is always forced on.
This got introduced in 3.10 via commit 6a7252fdb0c3 ([SCSI] lpfc:
fix up Kconfig dependencies). I spoke to Randy about it and
the original issue was with CRC_T10DIF not being defined.
As such, remove the select of CONFIG_GENERIC_CSUM.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is three bug fixes: An fnic warning caused by sleeping under a
lock, a major regression with our updated WRITE SAME/UNMAP logic which
caused tons of USB devices (and one RAID card) to cease to function
and a megaraid_sas firmware initialisation problem which causes kdump
failures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Don't attempt to send extended INQUIRY command if skip_vpd_pages is set
[SCSI] fnic: BUG: sleeping function called from invalid context during probe
[SCSI] megaraid_sas: megaraid_sas driver init fails in kdump kernel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"More virtio console fixes than I'm happy with, but all real issues,
and all CC:stable.."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-scsi: Fix virtqueue affinity setup
virtio: console: return -ENODEV on all read operations after unplug
virtio: console: fix raising SIGIO after port unplug
virtio: console: clean up port data immediately at time of unplug
virtio: console: fix race in port_fops_open() and port unplug
virtio: console: fix race with port unplug and open/close
virtio/console: Add pipe_lock/unlock for splice_write
virtio/console: Quit from splice_write if pipe->nrbufs is 0
|
|
If a device has the skip_vpd_pages flag set we should simply fail the
scsi_get_vpd_page() call.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Stuart Foster <smf.linux@ntlworld.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
I hit this during driver probe with the latest fnic updates (this trace
is from a backport into a distro kernel, but the issue is the same).
> BUG: sleeping function called from invalid context at mm/slab.c:3113
> in_atomic(): 0, irqs_disabled(): 1, pid: 610, name: work_for_cpu
> INFO: lockdep is turned off.
> irq event stamp: 0
> hardirqs last enabled at (0): [<(null)>] (null)
> hardirqs last disabled at (0): [<ffffffff81070aa5>]
> copy_process+0x5e5/0x1670
> softirqs last enabled at (0): [<ffffffff81070aa5>]
> copy_process+0x5e5/0x1670
> softirqs last disabled at (0): [<(null)>] (null)
> Pid: 610, comm: work_for_cpu Not tainted
> Call Trace:
> [<ffffffff810b2d10>] ? print_irqtrace_events+0xd0/0xe0
> [<ffffffff8105c1a7>] ? __might_sleep+0xf7/0x130
> [<ffffffff81184efb>] ? kmem_cache_alloc_trace+0x20b/0x2d0
> [<ffffffff8109709e>] ? __create_workqueue_key+0x3e/0x1d0
> [<ffffffff8109709e>] ? __create_workqueue_key+0x3e/0x1d0
> [<ffffffffa00c101c>] ? fnic_probe+0x977/0x11aa [fnic]
> [<ffffffffa00c1048>] ? fnic_probe+0x9a3/0x11aa [fnic]
> [<ffffffff81096f00>] ? do_work_for_cpu+0x0/0x30
> [<ffffffff812c6da7>] ? local_pci_probe+0x17/0x20
> [<ffffffff81096f18>] ? do_work_for_cpu+0x18/0x30
> [<ffffffff8109cdc6>] ? kthread+0x96/0xa0
> [<ffffffff8100c1ca>] ? child_rip+0xa/0x20
> [<ffffffff81550f80>] ? _spin_unlock_irq+0x30/0x40
> [<ffffffff8100bb10>] ? restore_args+0x0/0x30
> [<ffffffff8109cd30>] ? kthread+0x0/0xa0
> [<ffffffff8100c1c0>] ? child_rip+0x0/0x20
The problem is in this hunk of "FIP VLAN Discovery Feature Support"
(d3c995f1dcf938f1084388d92b8fb97bec366566)
create_singlethreaded_workqueue cannot be called with irqs disabled
@@ -620,7 +634,29 @@ static int __devinit fnic_probe(struct pci_dev
*pdev,
vnic_dev_packet_filter(fnic->vdev, 1, 1, 0, 0, 0);
vnic_dev_add_addr(fnic->vdev, FIP_ALL_ENODE_MACS);
vnic_dev_add_addr(fnic->vdev, fnic->ctlr.ctl_src_addr);
+ fnic->set_vlan = fnic_set_vlan;
fcoe_ctlr_init(&fnic->ctlr, FIP_MODE_AUTO);
+ setup_timer(&fnic->fip_timer, fnic_fip_notify_timer,
+ (unsigned long)fnic);
+ spin_lock_init(&fnic->vlans_lock);
+ INIT_WORK(&fnic->fip_frame_work, fnic_handle_fip_frame);
+ INIT_WORK(&fnic->event_work, fnic_handle_event);
+ skb_queue_head_init(&fnic->fip_frame_queue);
+ spin_lock_irqsave(&fnic_list_lock, flags);
+ if (!fnic_fip_queue) {
+ fnic_fip_queue =
+ create_singlethread_workqueue("fnic_fip_q");
+ if (!fnic_fip_queue) {
+ spin_unlock_irqrestore(&fnic_list_lock, flags);
+ printk(KERN_ERR PFX "fnic FIP work queue "
+ "create failed\n");
+ err = -ENOMEM;
+ goto err_out_free_max_pool;
+ }
+ }
+ spin_unlock_irqrestore(&fnic_list_lock, flags);
+ INIT_LIST_HEAD(&fnic->evlist);
+ INIT_LIST_HEAD(&fnic->vlans);
} else {
shost_printk(KERN_INFO, fnic->lport->host,
"firmware uses non-FIP mode\n");
The attempts to make fnic_fip_queue a single instance for the driver
while it's being created in probe look awkward anyway, why is this not
created in fnic_init_module like the event workqueue?
Signed-off-by: Chris Leech <cleech@redhat.com>
Tested-by: Anantha Tungarakodi <atungara@cisco.com>
Acked-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Problem: When Hardware IOMMU is on, megaraid_sas driver initialization fails
in kdump kernel with LSI MegaRAID controller(device id-0x73).
Actually this issue needs fix in firmware, but for firmware running in field,
this driver fix is proposed to resolve the issue. At firmware initialization
time, if firmware does not come to ready state, driver will reset the adapter
and retry for firmware transition to ready state unconditionally(not only
executed for kdump kernel).
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
vscsi->num_queues counts the number of request virtqueue which does not
include the control and event virtqueue. It is wrong to subtract
VIRTIO_SCSI_VQ_BASE from vscsi->num_queues.
This patch fixes the following panic.
(qemu) device_del scsi0
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffff8179b29f>] __virtscsi_set_affinity+0x6f/0x120
PGD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 659 Comm: kworker/0:1 Not tainted 3.11.0-rc2+ #1172
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: kacpi_hotplug _handle_hotplug_event_func
task: ffff88007bee1cc0 ti: ffff88007bfe4000 task.ti: ffff88007bfe4000
RIP: 0010:[<ffffffff8179b29f>] [<ffffffff8179b29f>] __virtscsi_set_affinity+0x6f/0x120
RSP: 0018:ffff88007bfe5a38 EFLAGS: 00010202
RAX: 0000000000000010 RBX: ffff880077fd0d28 RCX: 0000000000000050
RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000000
RBP: ffff88007bfe5a58 R08: ffff880077f6ff00 R09: 0000000000000001
R10: ffffffff8143e673 R11: 0000000000000001 R12: 0000000000000001
R13: ffff880077fd0800 R14: 0000000000000000 R15: ffff88007bf489b0
FS: 0000000000000000(0000) GS:ffff88007ea00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000020 CR3: 0000000079f8b000 CR4: 00000000000006f0
Stack:
ffff880077fd0d28 0000000000000000 ffff880077fd0800 0000000000000008
ffff88007bfe5a78 ffffffff8179b37d ffff88007bccc800 ffff88007bccc800
ffff88007bfe5a98 ffffffff8179b3b6 ffff88007bccc800 ffff880077fd0d28
Call Trace:
[<ffffffff8179b37d>] virtscsi_set_affinity+0x2d/0x40
[<ffffffff8179b3b6>] virtscsi_remove_vqs+0x26/0x50
[<ffffffff8179c7d2>] virtscsi_remove+0x82/0xa0
[<ffffffff814cb6b2>] virtio_dev_remove+0x22/0x70
[<ffffffff8167ca49>] __device_release_driver+0x69/0xd0
[<ffffffff8167cb9d>] device_release_driver+0x2d/0x40
[<ffffffff8167bb96>] bus_remove_device+0x116/0x150
[<ffffffff81679936>] device_del+0x126/0x1e0
[<ffffffff81679a06>] device_unregister+0x16/0x30
[<ffffffff814cb889>] unregister_virtio_device+0x19/0x30
[<ffffffff814cdad6>] virtio_pci_remove+0x36/0x80
[<ffffffff81464ae7>] pci_device_remove+0x37/0x70
[<ffffffff8167ca49>] __device_release_driver+0x69/0xd0
[<ffffffff8167cb9d>] device_release_driver+0x2d/0x40
[<ffffffff8167bb96>] bus_remove_device+0x116/0x150
[<ffffffff81679936>] device_del+0x126/0x1e0
[<ffffffff8145edfc>] pci_stop_bus_device+0x9c/0xb0
[<ffffffff8145f036>] pci_stop_and_remove_bus_device+0x16/0x30
[<ffffffff81474a9e>] acpiphp_disable_slot+0x8e/0x150
[<ffffffff81474f6a>] hotplug_event_func+0xba/0x1a0
[<ffffffff814906c8>] ? acpi_os_release_object+0xe/0x12
[<ffffffff81475911>] _handle_hotplug_event_func+0x31/0x70
[<ffffffff810b5333>] process_one_work+0x183/0x500
[<ffffffff810b66e2>] worker_thread+0x122/0x400
[<ffffffff810b65c0>] ? manage_workers+0x2d0/0x2d0
[<ffffffff810bc5de>] kthread+0xce/0xe0
[<ffffffff810bc510>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff81ca045c>] ret_from_fork+0x7c/0xb0
[<ffffffff810bc510>] ? kthread_freezable_should_stop+0x70/0x70
Code: 01 00 00 00 74 59 45 31 e4 83 bb c8 01 00 00 02 74 46 66 2e 0f 1f 84 00 00 00 00 00 49 63 c4 48 c1 e0 04 48 8b bc 0
3 10 02 00 00 <48> 8b 47 20 48 8b 80 d0 01 00 00 48 8b 40 50 48 85 c0 74 07 be
RIP [<ffffffff8179b29f>] __virtscsi_set_affinity+0x6f/0x120
RSP <ffff88007bfe5a38>
CR2: 0000000000000020
---[ end trace 99679331a3775f48 ]---
CC: stable@vger.kernel.org
Signed-off-by: Asias He <asias@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Oops, apparently no-one I cc'd at intel actually bothered to check this
patch for the isci driver:
commit e73823f7a2c921dcf068d34ea03bd682498d9e42
Author: James Bottomley <JBottomley@Parallels.com>
Date: Tue May 7 15:38:18 2013 -0700
[SCSI] libsas: implement > 16 byte CDB support
sci_swab32_cpy needs multiples of four, so for commands that aren't that, it's
rounding the wrong way. fix by doing (len+3)/4 instead of len/4.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
slot->response is a 64 bit quantity (and accessed as such), but its alignment
is only 32 bits. This doesn't cause a problem on x86, but apparently causes a
kernel panic on Tile:
Stack dump complete Kernel panic - not syncing:
Kernel unalign fault running the idle task!
Starting stack dump of tid 0, pid 0 (swapper) on cpu 1 at cycle 341586172541
frame 0: 0xfffffff700140ee0 dump_stack+0x0/0x20 (sp 0xfffffe43ffedf420)
frame 1: 0xfffffff700283270 panic+0x150/0x3a0 (sp 0xfffffe43ffedf420)
frame 2: 0xfffffff70012bff8 jit_bundle_gen+0xfd8/0x27e0 (sp 0xfffffe43ffedf4c8)
frame 3: 0xfffffff7003b5b68 do_unaligned+0xc0/0x5a0 (sp 0xfffffe43ffedf710)
frame 4: 0xfffffff70044ca78 handle_interrupt+0x270/0x278 (sp 0xfffffe43ffedf840)
<interrupt 17 while in kernel mode>
frame 5: 0xfffffff7002ac370 mvs_slot_complete+0x5f0/0x12a0 (sp 0xfffffe43ffedfa90)
frame 6: 0xfffffff7002abec0 mvs_slot_complete+0x140/0x12a0 (sp 0xfffffe43ffedfa90)
frame 7: 0xfffffff7005cc840 mvs_int_rx+0x140/0x2a0 (sp 0xfffffe43ffedfb00)
frame 8: 0xfffffff7005bbaf0 mvs_94xx_isr+0xd8/0x2b8 (sp 0xfffffe43ffedfb68)
frame 9: 0xfffffff700658ba0 mvs_tasklet+0x128/0x1f8 (sp 0xfffffe43ffedfba8)
frame 10: 0xfffffff7003e8230 tasklet_action+0x178/0x2c8 (sp 0xfffffe43ffedfbe0)
frame 11: 0xfffffff700103850 __do_softirq+0x210/0x398 (sp 0xfffffe43ffedfc40)
frame 12: 0xfffffff700180308 do_softirq+0xc8/0x140 (sp 0xfffffe43ffedfcd8)
frame 13: 0xfffffff7000bd7f0 irq_exit+0xb0/0x158 (sp 0xfffffe43ffedfcf0)
frame 14: 0xfffffff70013fa58 tile_dev_intr+0x1d8/0x2f0 (sp 0xfffffe43ffedfd00)
frame 15: 0xfffffff70044ca78 handle_interrupt+0x270/0x278 (sp 0xfffffe43ffedfd40)
<interrupt 30 while in kernel mode>
frame 16: 0xfffffff700143e68 _cpu_idle_nap+0x0/0x18 (sp 0xfffffe43ffedffb0)
frame 17: 0xfffffff700482480 cpu_idle+0x310/0x428 (sp 0xfffffe43ffedffb0)
Since the check is just for non-zero, split it to be two 32 bit accesses
(preserving speed in the fast path) and do a get_unaligned() in the slow path.
This is a modification of a wholly get_unaligned patch submitted by Paul Guo
Reported-by: Paul Guo <ggang@tilera.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
sd_prep_fn will allocate a larger CDB for the command via mempool_alloc
for devices using DIF type 2 protection. This CDB was being freed
in sd_done, which results in a kernel crash if the command is retried
due to a UNIT ATTENTION. This change moves the code to free the larger
CDB into sd_unprep_fn instead, which is invoked after the request is
complete.
It is no longer necessary to call scsi_print_command separately for
this case as the ->cmnd will no longer be NULL in the normal code path.
Also removed conditional test for DIF type 2 when freeing the larger
CDB because the protection_type could have been changed via sysfs while
the command was executing.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fixes a regression where Xyratex controllers and disks were lost by the
driver:
https://bugzilla.kernel.org/show_bug.cgi?id=59601
Reported-by: Jack Hill <jackhill@jackhill.us>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This commit fixes a race condition in the isci driver abort task and SSP
device task management path. The race is caused when an I/O termination
in the SCU hardware is necessary because of an SSP target timeout condition,
and the check of the I/O end state races against the HW-termination-driven
end state. The failure of the race meant that no TMF was sent to the device
to clean-up the pending I/O.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Reviewed-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"This is the remaining set of SCSI patches for the merge window. It's
mostly driver updates (scsi_debug, qla2xxx, storvsc, mp3sas). There
are also several bug fixes in fcoe, libfc, and megaraid_sas. We also
have a couple of core changes to try to make device destruction more
deterministic"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
[SCSI] scsi constants: command, sense key + additional sense strings
fcoe: Reduce number of sparse warnings
fcoe: Stop fc_rport_priv structure leak
libfcoe: Fix meaningless log statement
libfc: Differentiate echange timer cancellation debug statements
libfc: Remove extra space in fc_exch_timer_cancel definition
fcoe: fix the link error status block sparse warnings
fcoe: Fix smatch warning in fcoe_fdmi_info function
libfc: Reject PLOGI from nodes with incompatible role
[SCSI] enable destruction of blocked devices which fail LUN scanning
[SCSI] Fix race between starved list and device removal
[SCSI] megaraid_sas: fix a bug for 64 bit arches
[SCSI] scsi_debug: reduce duplication between prot_verify_read and prot_verify_write
[SCSI] scsi_debug: simplify offset calculation for dif_storep
[SCSI] scsi_debug: invalidate protection info for unmapped region
[SCSI] scsi_debug: fix NULL pointer dereference with parameters dif=0 dix=1
[SCSI] scsi_debug: fix incorrectly nested kmap_atomic()
[SCSI] scsi_debug: fix invalid address passed to kunmap_atomic()
[SCSI] mpt3sas: Bump driver version to v02.100.00.00
[SCSI] mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed
...
|
|
A short series of fixes to libfc, libfcoe and fcoe.
Most patches fix formatting problems, one changes
the behavior of which discovered ports can/will be
logged into and another fixes a memory leak.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity this round on performance improvements in target-core
while benchmarking the prototype scsi-mq initiator code with
vhost-scsi fabric ports, along with a number of iscsi/iser-target
improvements and hardening fixes for exception path cases post v3.10
merge.
The highlights include:
- Make persistent reservations APTPL buffer allocated on-demand, and
drop per t10_reservation buffer. (grover)
- Make virtual LUN=0 a NULLIO device, and skip allocation of NULLIO
device pages (grover)
- Add transport_cmd_check_stop write_pending bit to avoid extra
access of ->t_state_lock is WRITE I/O submission fast-path. (nab)
- Drop unnecessary CMD_T_DEV_ACTIVE check from
transport_lun_remove_cmd to avoid extra access of ->t_state_lock in
release fast-path. (nab)
- Avoid extra t_state_lock access in __target_execute_cmd fast-path
(nab)
- Drop unnecessary vhost-scsi wait_for_tasks=true usage +
->t_state_lock access in release fast-path. (nab)
- Convert vhost-scsi to use modern se_cmd->cmd_kref
TARGET_SCF_ACK_KREF usage (nab)
- Add tracepoints for SCSI commands being processed (roland)
- Refactoring of iscsi-target handling of ISCSI_OP_NOOP +
ISCSI_OP_TEXT to be transport independent (nab)
- Add iscsi-target SendTargets=$IQN support for in-band discovery
(nab)
- Add iser-target support for in-band discovery (nab + Or)
- Add iscsi-target demo-mode TPG authentication context support (nab)
- Fix isert_put_reject payload buffer post (nab)
- Fix iscsit_add_reject* usage for iser (nab)
- Fix iscsit_sequence_cmd reject handling for iser (nab)
- Fix ISCSI_OP_SCSI_TMFUNC handling for iser (nab)
- Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED (nab)
The last five iscsi/iser-target items are CC'ed to stable, as they do
address issues present in v3.10 code. They are certainly larger than
I'd like for stable patch set, but are important to ensure proper
REJECT exception handling in iser-target for 3.10.y"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
iser-target: Ignore non TEXT + LOGOUT opcodes for discovery
target: make queue_tm_rsp() return void
target: remove unused codes from enum tcm_tmrsp_table
iscsi-target: kstrtou* configfs attribute parameter cleanups
iscsi-target: Fix tfc_tpg_auth_cit configfs length overflow
iscsi-target: Fix tfc_tpg_nacl_auth_cit configfs length overflow
iser-target: Add support for ISCSI_OP_TEXT opcode + payload handling
iser-target: Rename sense_buf_[dma,len] to pdu_[dma,len]
iser-target: Add vendor_err debug output
target: Add (obsolete) checking for PMI/LBA fields in READ CAPACITY(10)
target: Return correct sense data for IO past the end of a device
target: Add tracepoints for SCSI commands being processed
iser-target: Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED
iscsi-target: Fix ISCSI_OP_SCSI_TMFUNC handling for iser
iscsi-target: Fix iscsit_sequence_cmd reject handling for iser
iscsi-target: Fix iscsit_add_reject* usage for iser
iser-target: Fix isert_put_reject payload buffer post
iscsi-target: missing kfree() on error path
iscsi-target: Drop left-over iscsi_conn->bad_hdr
target: Make core_scsi3_update_and_write_aptpl return sense_reason_t
...
|
|
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a999 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
|
|
It has been several years since the SCSI constants.c
file has been updated. The attached is against lk 3.10
and brings the command strings, sense keys and additional
sense code strings into sync with spc4r36g.pdf.
Certain SCSI command names that previously only took the
opcode (i.e. byte 0 of the cdb) into account, have been
split into several command names using the associated
service action field to differentiate. For example,
persistent reservations that previously had 2 commands
(i.e. "in" and "out") have been expanded to 12 commands
(e.g. "Persistent reserve in, read reservation").
Sync SCSI command names, sense key strings and additional
sense code strings with SPC-4 draft revision 36g
[jejb: whitespace fix]
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Declare local variables and functions 'static'. This patch does not
change any functionality.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
When repeatedly doing rmmod and modprobe on the ixgbe
driver while FCoE is active in a VN2VN configuration,
memory leaks would be discovered by kmemleak with the
following backtrace:
unreferenced object 0xffff88003d076000 (size 1024):
comm "kworker/0:3", pid 2998, jiffies 4295436448 (age 1015.332s)
hex dump (first 32 bytes):
48 8a fe 6f 00 88 ff ff 00 00 00 00 00 00 00 00 H..o............
01 00 00 00 02 00 00 00 7b ac 87 21 1b 00 00 10 ........{..!....
backtrace:
[<ffffffff814b308b>] kmemleak_alloc+0x5b/0xc0
[<ffffffff8115c6e8>] __kmalloc+0xd8/0x1b0
[<ffffffffa0216638>] fc_rport_create+0x48/0x1f0 [libfc]
[<ffffffffa023cd86>] fcoe_ctlr_vn_add.isra.10+0x56/0x1a0 [libfcoe]
[<ffffffffa023f440>] fcoe_ctlr_vn_recv+0x8b0/0xab0 [libfcoe]
[<ffffffffa023fb06>] fcoe_ctlr_recv_work+0x4c6/0xf60 [libfcoe]
[<ffffffff81067404>] process_one_work+0x1e4/0x4d0
[<ffffffff81068def>] worker_thread+0x10f/0x380
[<ffffffff8107019a>] kthread+0xea/0xf0
[<ffffffff814d32ec>] ret_from_fork+0x7c/0xb0
[<ffffffffffffffff>] 0xffffffffffffffff
This patch stops the leak of the fc_rport_priv structure.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
ctlr_dev was initialized to NULL, and never re-assigned. This
caused the log statement to always report failure. This patch
removes the unused variable and fixes the log statement to always
report 'success', as that is what should be logged if the code
reaches this point.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
|
|
There are two debug statements with the same output string regarding
echange timer cancellation. This patch simply changes the output of
one string so that they can be differentiated.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
|
|
Simply remove an extra space that violates coding style.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
|
|
Both fcoe_fc_els_lesb and fc_els_lesb are in __be32 already, and both are
exactly the same size in bytes, with somewhat different member names to
reflect the fact the former is for Ethernet media the latter is for Fiber
Channel, so, remove conversion and use __be32 directly. This fixes the warning
from sparse check.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
do_device_access() is a function that abstracts copying SG list from/to
ramdisk storage (fake_storep).
It must deal with the ranges exceeding actual fake_storep size, because
such ranges are valid if virtual_gb is set greater than zero, and they
should be treated as fake_storep is repeatedly mirrored up to virtual
size.
Unfortunately, it can't deal with the range which wraps around the end of
fake_storep. A wrap around range is copied by two
sg_copy_{from,to}_buffer() calls, but sg_copy_{from,to}_buffer() can't
copy from/to in the middle of SG list, therefore the second call can't
copy correctly.
This fixes it by using sg_pcopy_{from,to}_buffer() that can copy from/to
the middle of SG list.
This also simplifies the assignment of sdb->resid in
fill_from_dev_buffer(). Because fill_from_dev_buffer() is now only called
once per command execution cycle. So it is not necessary to take care to
decrease sdb->resid if fill_from_dev_buffer() is called more than once.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes a smatch warning as below:
smatch warnings:
drivers/scsi/fcoe/fcoe.c:782 fcoe_fdmi_info() warn: 'fdmi' puts 896 bytes on
stack
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
Reject a PLOGI from a node with an incompatible role,
that is, initiator-to-initiator or target-to-target.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
If something goes wrong during LUN scanning, e.g. a transport layer
failure occurs, then __scsi_remove_device() can get invoked by the
LUN scanning code for a SCSI device in state SDEV_CREATED_BLOCK and
before the SCSI device has been added to sysfs (is_visible == 0).
Make sure that even in this case the transition into state SDEV_DEL
occurs. This avoids that __scsi_remove_device() can get invoked a
second time by scsi_forget_host() if this last function is invoked
from another thread than the thread that performs LUN scanning.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
scsi_run_queue() examines all SCSI devices that are present on
the starved list. Since scsi_run_queue() unlocks the SCSI host
lock a SCSI device can get removed after it has been removed
from the starved list and before its queue is run. Protect
against that race condition by holding a reference on the
queue while running it.
Reported-by: Chanho Min <chanho.min@lge.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
On 64 bit then -1UL and -1U are not equal, so these conditions don't
work as intended and it breaks error handling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
prot_verify_write
In order to reduce code duplication between prot_verify_read() and
prot_verify_write(), this moves common code into the new functions.
[jejb: fix unitialised variable warning]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
dif_storep is declared as pointer to unsigned char type. But it is
actually used to store vmalloced array of struct sd_dif_tuple.
This changes the type of dif_storep to the pointer to struct sd_dif_tuple.
It simplifies offset calculation for dif_storep and enables to remove
hardcoded size of struct sd_dif_tuple.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When UNMAP command is issued with the data integrity support enabled,
the protection info for the unmapped region is remain unchanged.
So READ command for the region later on causes data integrity failure.
This fixes it by invalidating protection info for the unmapped region
by filling with 0xff pattern.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The protection info dif_storep is allocated only when parameter dif is
not zero. But it will be accessed when reading or writing to the storage
installed with parameter dix is not zero.
So kernel crashes if scsi_debug module is loaded with parameters dix=1 and
dif=0.
This fixes it by making dif_storep available if parameter dix is not zero
instead of checking if parameter dif is not zero.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In the function prot_verify_write(), kmap_atomic()/kunmap_atomic() for
data page and kmap_atomic()/kunmap_atomic() for protection information
page are not nested each other.
It worked perfectly before commit 3e4d3af501cccdc8a8cca41bdbe57d54ad7e7e73
("mm: stack based kmap_atomic()"). Because the kmap_atomic slot KM_IRQ0
was used for data page and the slot KM_IRQ1 was used for protection page.
But KM_types are gone and kmap_atomic() is using stack based implementation.
So two different kmap_atomic() usages must be strictly nested now.
This change ensures kmap_atomic() usage is strictly nested.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In the function prot_verify_write(), the kmap address 'daddr' is
incremented in the loop for each data page. Finally 'daddr' reaches
the next page boundary in the end of the loop, and the invalid address
is passed to kunmap_atomic().
Fix the issue by not incrementing 'daddr' in the loop and offsetting it
by the loop counter on demand.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Bump driver version to v02.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
are removed but their transport layer entries are not removed
When Async scanning mode is enabled and device scanning is in progress,
devices should not be removed. But in actuality, devices are removed but
their transport layer entries are not removed. This causes error to add
the same device to the transport layer after host reset or diagnostic
reset.
So, in this patch, modified the code in such a way that device is not removed
when Async scanning mode is enabled and device scanning is in progress.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Change set in MPI v2.5 Rev F(v2.5.1.1) specification and 2.00.29 header files
1. Added a bit to the IOCExceptions field of the IOCFacts Reply to indicate
that the IOC detected a partial memory failure.
2. Added ElapsedSeconds field to RAID Volume Indicator Structure. Added
Elapsed Seconds Valid flag to Flags field of this structure.
3. Added ElapsedSeconds field to Integrated RAID Operations Status Event Data.
4. Added two new AbortType values for TargetModeAbort Request, one to abort
all I/Os from a single initiator, and the other to abort only Command IUs.
5. Added a new chapter covering DMA Flags and Multicast Modes.
6. In the IOCSettings field of BIOS Page 1, modified the Adapter Support bits
description to specify X86 BIOS.
7. Marked bit 0 of the ControlFlags field of SAS IO Unit Page 1 as
obsolete. This was the Clear SATA Affiliation flag.
8. Added additional requirements for certain IOCs that support more than eight
MSI-x vectors.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE is not returned
Infinite loop can occur if IOCStatus is not equal to
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value in the while loops in functions
_scsih_search_responding_sas_devices,
_scsih_search_responding_raid_devices and
_scsih_search_responding_expanders
So, Instead of checking for MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value,
in this patch code is modified to check for IOCStatus not equals to
MPI2_IOCSTATUS_SUCCESS to break the while loop.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
non LUN 0 configured expander
With some enclosures when LUN 0 is not created but LUN 1 or LUN X is created
then SCSI scan procedure calls target_alloc, slave_alloc call back functions
for LUN 0 and slave_destory() for same LUN 0.
In these kind of cases within slave_destroy, pointer to scsi_target in
_sas_device structure is set to NULL, following which when slave_alloc for LUN
1 is called then starget would not be set properly for this LUN. So,
scsi_target pointer pointing to NULL value would lead to a crash later in the
discovery procedure.
To solve this issue set the sas_device's scsi_target pointer to scsi_device's
scsi_target if it is NULL earlier in slave_alloc callback function.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Hardware timing requirements is updated in order to comply with firmware
requirement.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The Copyright String in all mpt3sas files are changed to 2012-2013.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Avoid that the fcport structure gets leaked if
bsg_job->request->msgcode == FC_BSG_HST_ELS_NOLOGIN, the fcport
allocation succeeds and the !vha->flags.online branch is taken.
This was detected by Coverity. However, Coverity does not recognize
that all qla2x00_process_els() callers specify either
FC_BSG_RPT_ELS or FC_BSG_HST_ELS_NOLOGIN in the field
bsg_job->request->msgcode and that the value of that field is not
modified inside that function. This results in a false positive
report about a possible memory leak in an error path for
bsg_job->request->msgcode values other than the two mentioned
values. Make it easy for Coverity (and for humans) to recognize
that there is no fcport leak in the error path by changing the
bsg_job->request->msgcode == FC_BSG_HST_ELS_NOLOGIN test into
bsg_job->request->msgcode != FC_BSG_RPT_ELS.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Change the 'rval' variable from QLA_FUNCTION_TIMEOUT into QLA_SUCCESS
before starting a loop that is only executed if rval is initialized
to QLA_SUCCESS. Coverity reported that loop as "dead code".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Coverity reports "Overrunning struct type ct_sns_req of 1228 bytes
by passing it to a function which accesses it at byte offset 8207"
for each qla2x00_prep_ct_req(), qla2x00_prep_ct_fdmi_req() and
qla24xx_prep_ct_fm_req() call. Help Coverity to recognize that
these calls do not trigger a buffer overflow by making it explicit
that these three functions initializes both the request and reply
structures. This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The value of the pointer called "nxt" is not used after the
"nxt = qla24xx_copy_eft(ha, nxt)" statement. Hence keep the function
call but remove the assignment.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since the value of cur_seg is not used and since scsi_prot_sglist()
has no side effects it is safe to remove the statement
"cur_seg = scsi_port_sglist(cmd)". Detected by Coverity.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since ha->model_desc is an array comparing it against NULL is
superfluous. Hence remove these tests.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
