| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As defined in table 126 of the SAS spec 1.1, use an enum for the DATAPRES
field, which makes reading the code easier.
Also change sas_ssp_task_response() to use a switch statement, which is
more suitable (than if-else), as suggested by Christoph.
Link: https://lore.kernel.org/r/1645112566-115804-3-git-send-email-john.garry@huawei.com
Suggested-by: Xiang Chen <chenxiang66@hisilicon.com>
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch prepares for converting SAM status codes into an enum. Without
this patch converting SAM status codes into an enumeration type would
trigger complaints about enum type mismatches for the SAS code.
Link: https://lore.kernel.org/r/20210524025457.11299-2-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.com>
Cc: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Cc: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently we use a mixture of %016llx, %llx, and %16llx when printing a SAS
address.
Since the most significant nibble of the SAS address is always 5 - as per
standard - this formatting is not so important; but some fake SAS addresses
for SATA devices may not be. And we have mangled/invalid address to
consider also. And it's better to be consistent in the code, so use a fixed
format.
The SAS address is a fixed size at 64b, so we want to 0 byte extend to 16
nibbles, so use %016llx globally.
Also make some prints to be explicitly hex, and tidy some whitespace issue.
Link: https://lore.kernel.org/r/1576758957-227350-1-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Like sas_printk() did previously, SAS_DPRINTK() offers little value now
that libsas logs already have the "sas" prefix through pr_fmt(fmt). So it
can be dropped.
However, after reviewing some logs in libsas, it is noticed that debug
level is too low in many instances.
So this change drops SAS_DPRINTK() and revises some logs to a more
appropriate level. However many stay at debug level, although some
are significantly promoted.
We add -DDEBUG for compilation so that we keep the debug messages by
default, as before.
All the pre-existing checkpatch errors for spanning messages across
multiple lines are also fixed.
Finally, all other references to printk() [apart from special formatting
in sas_ata.c] are removed and replaced with appropriate pr_xxx().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation for dropping the libsas printk wrappers, use pr_fmt(fmt)
declaration to add the framework log prefix - "sas".
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
We have two separate definitions for identical constants with nearly the
same name. One comes from the generic headers in scsi.h; the other is
an enum in libsas.h ... it's causing confusion about which one is
correct (fortunately they both are).
Fix this by eliminating the libsas.h duplicate
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Break out the frame processor for STP tasks from aic94xx so they can
be shared by other SAS HBA's
Original patch from Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
