Age | Commit message (Collapse) | Author | Files | Lines |
|
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When IO is successfully completed while an abort is pending, eh_abort
incorrectly assumes that abort failed and performes recovery by issuing
cleanup. Howerver, cleanup timesout as the firmware has no clue about
this IO. Fix this by checking if the IO has already completed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
[jejb: move PCI_DEVICE_ID definitions to include/pci_ids.h]
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Set perf_config to 3 during firmware initialization to enable both
cached connections as well as cached tasks.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The firmware supports a maximum of 4K FCoE exchanges. In 4-port devices,
or when working in multi-function mode, this resource needs to be distributed
between the various possible FCoE functions.
This information needs to be calculated by bnx2x and propagated into bnx2fc
via cnic. bnx2fc can then use this value to calculate corresponding xid
resources instead of using global constants.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split discovery initialization in code that is setup once (fcoe_disc_init)
and code that can be re-configured (fcoe_disc_config).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
|
|
initialization
Currently libfcoe is doing some libfc discovery layer initialization outside of
libfc. This patch moves this code into libfc and sets up a split in discovery
(one time) initialization code and (re-configurable) settings that will come in
the next patch.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
|
|
The fcoemon userspace daemon is searching for the a hostX
under the the /sys/bus/fcoe/devices/ctlrX/ entries. When
interfaces created using fcoe_sysfs and fcoe.ko this linkage
is setup correctly, but bnx2fc is not doing the same thing
and therefore fcoemon does not create the fcoe interface
for bnx2fc.
This patch sets up the correct linkage for bnx2fc such that
fcoemon will work correctly with fcoe_sysfs and bnx2fc.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
|
|
FCoE Updates for 3.9
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Delete successive tests to the same location. The code tested the result
of a previous allocation, that itself was already tested. It is changed to
test the result of the most recent allocation.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Increase max_sectors from 512 to 1024 in order to support max IO size of 512KB.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since the FW counters are 32-bit, accumulate the stats in the driver.
[jejb: fix checkpatch warning]
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We used to map doorbell register after FW enable request is complete.
This causes a race condition when unsolicited event is received, and FW
sends a CQE for it. Since the doorbell is not mapped, driver does not
arm CQ, which means FW will not notify the driver for further CQ
completions. To resolve this, map the doorbell between offload and
enable, so that driver is ready to receive the unsolicited packets and
arm the CQ as soon as FW enable is performed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Moved the 'waiting for upload/offload completion' logic to respective
functions as it is called in multiple places. Also this is done in
preperation for the next patch.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Software FCoE target always advertises RETRY bit even when there are no
tape LUNs behind the target. This causes the driver to enable FW support
for sequence level error recovery and perform REC/SRR. This patch
arrests the behavior by not enabling SLER feature for this target.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
These calls are followed by calls to memcpy() on the same memory area, so they
can be safely removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the bnx2fc_xxx versions as they are basically the same.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
We have fcoe_link_speed_update() in libfcoe ready for use now, take out the
bnx2fc version which is almost the same.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
Adds support to fcoe_port's newly added get_netdev fucntion pointer for bnx2fc.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
|
|
This patch adds support for the new fcoe_sysfs
control interface to bnx2fc.ko. It keeps the deprecated
interface in tact and therefore either the legacy
or the new control interfaces can be used. A mixed mode
is not supported. A user must either use the new
interfaces or the old ones, but not both.
The fcoe_ctlr's link state is now driven by both the
netdev link state as well as the fcoe_ctlr_device's
enabled attribute. The link must be up and the
fcoe_ctlr_device must be enabled before the FCoE
Controller starts discovery or login.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
|
|
This patch does a few things.
1) Makes /sys/bus/fcoe/ctlr_{create,destroy} interfaces.
These interfaces take an <ifname> and will either
create an FCoE Controller or destroy an FCoE
Controller depending on which file is written to.
The new FCoE Controller will start in a DISABLED
state and will not do discovery or login until it
is ENABLED. This pause will allow us to configure
the FCoE Controller before enabling it.
2) Makes the 'mode' attribute of a fcoe_ctlr_device
writale. This allows the user to configure the mode
in which the FCoE Controller will start in when it
is ENABLED.
Possible modes are 'Fabric', or 'VN2VN'.
The default mode for a fcoe_ctlr{,_device} is 'Fabric'.
Drivers must implement the set_fcoe_ctlr_mode routine
to support this feature.
libfcoe offers an exported routine to set a FCoE
Controller's mode. The mode can only be changed
when the FCoE Controller is DISABLED.
This patch also removes the get_fcoe_ctlr_mode pointer
in the fcoe_sysfs function template, the code in
fcoe_ctlr.c to get the mode and the assignment of
the fcoe_sysfs function pointer to the fcoe_ctlr.c
implementation (in fcoe and bnx2fc). fcoe_sysfs can
return that value for the mode without consulting the
LLD.
3) Make a 'enabled' attribute of a fcoe_ctlr_device. On a
read, fcoe_sysfs will return the attribute's value. On
a write, fcoe_sysfs will call the LLD (if there is a
callback) to notifiy that the enalbed state has changed.
This patch maintains the old FCoE control interfaces as
module parameters, but it adds comments pointing out that
the old interfaces are deprecated.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
|
|
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
|
|
gcc 4.8 warns because the memset only clears sizeof(char *) bytes, not
the whole buffer. Use the correct buffer size and clear the whole sense
buffer.
/backup/lsrc/git/linux-lto-2.6/drivers/scsi/bnx2fc/bnx2fc_io.c: In
function 'bnx2fc_parse_fcp_rsp':
/backup/lsrc/git/linux-lto-2.6/drivers/scsi/bnx2fc/bnx2fc_io.c:1810:41:
warning: argument to 'sizeof' in 'memset' call is the same expression as
the destination; did you mean to provide an explicit length?
[-Wsizeof-pointer-memaccess]
memset(sc_cmd->sense_buffer, 0, sizeof(sc_cmd->sense_buffer));
^
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Correct spelling typo within drivers/scsi
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
|
|
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Use list_for_each_entry_safe() instead of explicit cast to avoid relying on
struct layout
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
During parity errors, the ramrods are not issued to FW. bnx2fc waits for the
timeout value, and proceeds with cleaning up the IOs. Since we are already
out-of-sync with FW, cleanup commands timeout too, and do not get the
completion. This operation takes 36 secs for each session to upload causing
huge delays. To fix this, bnx2fc now gets a PARITY_ERROR from cnic driver, and
upon failure, the driver does not issue any commands to the FW and finishes the
upload process sooner.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
bnx2fc had an assumption that the fcoe interface will always start on the vlan
dev. However, some switch implementations (Eg., HP virtual connect FlexFabric)
expects the fcoe interface to be started on physical interface. Do not error
out if the netdev is not a vlan dev.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Deduplication of formats and consolidating tests
makes the object much smaller.
Add bnx2fc_debug.c, add functions for a few logging
functions (BNX2FC_IO_DBG, BNX2FC_TGT_DBG, BNX2FC_HBA_DBG).
Use printf extension %pV.
Add and use pr_fmt and pr_<level>.
Move the debug #include below structure definitions.
$ size drivers/scsi/bnx2fc/built-in.o*
text data bss dec hex filename
101563 1165 24976 127704 1f2d8 drivers/scsi/bnx2fc/built-in.o.new
138473 1109 33400 172982 2a3b6 drivers/scsi/bnx2fc/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since bnx2fc_percpu_thread_create() creates percpu kthread, it makes
sense to use kthread_create_on_node() to get proper NUMA affinity for
kthread stack.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The libfc is used by fcoe but fcoe agnostic,
and therefore should not have any fcoe references.
So renaming fcoe_dev_stats from libfc as its for fc_stats.
After that libfc is fcoe string free except some strings for
Open-FCoE.org.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
advertisement
1. When FCoE offload driver is registered, copy its capabilities to the chip
scratchpad.
2. Copy FCoE/iSCSI MAC addresses in aligned manner to chip scratchpad.
3. Add FCoE/iSCSI statistics collection support
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch has the SW FCoE driver and the bnx2fc
driver make use of the new fcoe_sysfs API added
earlier in this patch series.
After this patch a fcoe_ctlr_device is allocated with
private data in this order.
+------------------+ +------------------+
| fcoe_ctlr_device | | fcoe_ctlr_device |
+------------------+ +------------------+
| fcoe_ctlr | | fcoe_ctlr |
+------------------+ +------------------+
| fcoe_interface | | bnx2fc_interface |
+------------------+ +------------------+
libfcoe also takes part in this new model since it
discovers and manages fcoe_fcf instances. The memory
allocation is different for FCFs. I didn't want to
impact libfcoe's fcoe_fcf processing, so this patch
creates fcoe_fcf_device instances for each discovered
fcoe_fcf. The two are paired using a (void * priv)
member of the fcoe_ctlr_device. This allows libfcoe
to continue maintaining its list of fcoe_fcf instances
and simply attaches and detaches them from existing
or new fcoe_fcf_device instances.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently the fcoe_ctlr associated with an interface is allocated
as a member of struct bnx2fc_interface. This causes problems when
when later patches attempt to use the new fcoe_sysfs APIs which
allow us to allocate the bnx2fc_interface as private data to a
fcoe_ctlr_device instance. The problem is that libfcoe wants to
be able use pointer math to find a fcoe_ctlr's fcoe_ctlr_device
as well as finding a fcoe_ctlr_device's assocated fcoe_ctlr. To
do this we need to allocate the fcoe_ctlr_device, with private
data for the LLD. The private data will contain the fcoe_ctlr
and its private data will be the bnx2fc_interface.
+-------------------+
| fcoe_ctlr_device |
+-------------------+
| fcoe_ctlr |
+-------------------+
| bnx2fc_interface |
+-------------------+
This prep work will allow us to go from a fcoe_ctlr_device
instance to its fcoe_ctlr as well as from a fcoe_ctlr to its
fcoe_ctlr_device once the fcoe_sysfs API is in use (later
patches in this series).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When the task management IO times out, or a flush operation is performed while
task management IO is pending, driver is not cleaning up the IO. This patch
cleans up the IO for the above cases.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When IO abort times out during eh_abort or a flush operation is performed while
abort is pending, the driver is not cleaning up the IO and thus not reducing
the IO reference count. With this change, as part of explicit logout, the IO is
cleaned up.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Commit 907c07d45199f954ddcf66c2c9763c87d012cb15 added more cases to do FLOGI
retry on receiving bad response. Remove the code that drops the packet and
allow the stack to handle bad FLOGI response.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
|
|
As with the fcoe sw transport, the bnx2fc packet handler function runs only in
softirq context. Theres no need to disable bottom halves here
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pull networking fixes from David Miller:
1) L2TP doesn't get autoloaded when you try to open an L2TP socket due
to a missing module alias, fix from Benjamin LaHaise.
2) Netlabel and RDS should propagate gfp flags given to them by
callers, fixes from Dan Carpeneter.
3) Recursive locking fix in usbnet wasn't bulletproof and can result in
objects going away mid-flight due to races, fix from Ming Lei.
4) Fix up some confusion about a bool module parameter in netfilter's
iptable_filter and ip6table_filter, from Rusty Russell.
5) If SKB recycling is used via napi_reuse_skb() we end up with
different amounts of headroom reserved than we had at the original
SKB allocation. Fix from Eric Dumazet.
6) Fix races in TG3 driver ring refilling, from Michael Chan.
7) We have callbacks for IPSEC replay notifiers, but some call sites
were not using the ops method and instead were calling one of the
implementations directly. Oops. Fix from Steffen Klassert.
8) Fix IP address validation properly in the bonding driver, the
previous fix only works with netlink where the subnet mask and IP
address are changed in one atomic operation. When 'ifconfig' ioctls
are used the IP address and the subnet mask are changed in two
distinct operations. Fix from Andy Gospodarek.
9) Provide a sky2 module operation to work around power management
issues with some BIOSes. From Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
usbnet: consider device busy at each recieved packet
bonding: remove entries for master_ip and vlan_ip and query devices instead
netfilter: remove forward module param confusion.
usbnet: don't clear urb->dev in tx_complete
usbnet: increase URB reference count before usb_unlink_urb
xfrm: Access the replay notify functions via the registered callbacks
xfrm: Remove unused xfrm_state from xfrm_state_check_space
RDS: use gfp flags from caller in conn_alloc()
netlabel: use GFP flags from caller instead of GFP_ATOMIC
l2tp: enable automatic module loading for l2tp_ppp
cnic: Fix parity error code conflict
tg3: Fix RSS ring refill race condition
sky2: override for PCI legacy power management
net: fix napi_reuse_skb() skb reserve
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
|