summaryrefslogtreecommitdiffstats
path: root/drivers/scsi/arm/oak.c
AgeCommit message (Collapse)AuthorFilesLines
2018-12-18scsi: remove the use_clustering flagChristoph Hellwig1-1/+1
The same effects can be achieved by setting the dma_boundary to PAGE_SIZE - 1 and the max_segment_size to PAGE_SIZE, so shift those settings into the drivers. Note that in many cases the setting might be bogus, but this keeps the status quo. [mkp: fix myrs and myrb] Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-08-25scsi: NCR5380: Move bus reset to host resetHannes Reinecke1-1/+1
The bus reset handler really is a host reset, so move it to eh_bus_reset_handler. Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Use correct types for DMA routinesFinn Thain1-6/+7
Apply prototypes to get consistent function signatures for the DMA functions implemented in the board-specific drivers. To avoid using macros to alter actual parameters, some of those functions are reworked slightly. This is a step toward the goal of passing the board-specific routines to the core driver using an ops struct (as in a platform driver or library module). This also helps fix some inconsistent types: where the core driver uses ints (cmd->SCp.this_residual and hostdata->dma_len) for keeping track of transfers, certain board-specific routines used unsigned long. While we are fixing these function signatures, pass the hostdata pointer to DMA routines instead of a Scsi_Host pointer, for shorter and faster code. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Use correct types for device register accessorsFinn Thain1-4/+2
For timeout values adopt unsigned long, which is the type of jiffies etc. For chip register values and bit masks pass u8, which is the return type of readb, inb etc. For device register offsets adopt unsigned int, as it is suitable for adding to base addresses. Pass the NCR5380_hostdata pointer to the board-specific routines instead of the Scsi_Host pointer. The board-specific code is concerned with hardware and not with SCSI protocol or the mid-layer. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-11-08scsi: ncr5380: Store IO ports and addresses in host private dataFinn Thain1-12/+11
The various 5380 drivers inconsistently store register pointers either in the Scsi_Host struct "legacy crap" area or in special, board-specific members of the NCR5380_hostdata struct. Uniform use of the latter struct makes for simpler and faster code (see the following patches) and helps to reduce use of the NCR5380_implementation_fields macro. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove DONT_USE_INTR and AUTOPROBE_IRQ macrosFinn Thain1-2/+0
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Merge DMA implementation from atari_NCR5380 core driverFinn Thain1-1/+2
Adopt the DMA implementation from atari_NCR5380.c. This means that atari_scsi and sun3_scsi can make use of the NCR5380.c core driver and the atari_NCR5380.c driver fork can be made redundant. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Adopt uniform DMA setup conventionFinn Thain1-2/+2
Standardize the DMA setup hooks so that the DMA implementation in atari_NCR5380.c can be reconciled with pseudo DMA implementation in NCR5380.c. Calls to NCR5380_dma_recv_setup() and NCR5380_dma_send_setup() return a negative value on failure, zero on PDMA transfer success and a positive byte count for DMA setup success. This convention is not entirely new, but is now applied consistently. Also remove a pointless Status Register access: the *phase assignment is redundant because after NCR5380_transfer_dma() returns control to NCR5380_information_transfer(), that routine then returns control to NCR5380_main(), which means *phase is dead. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Use DMA hooks for PDMAFinn Thain1-4/+6
Those wrapper drivers which use DMA define the REAL_DMA macro and those which use pseudo DMA define PSEUDO_DMA. These macros need to be removed for a number of reasons, not least of which is to have drivers share more code. Redefine the PDMA send and receive hooks as DMA setup hooks, so that the DMA code can be shared by all 5380 wrapper drivers. This will help to reunify the forked core driver. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Remove PSEUDO_DMA macroFinn Thain1-2/+1
For those wrapper drivers which only implement Programmed IO, have NCR5380_dma_xfer_len() evaluate to zero. That allows PDMA to be easily disabled at run-time and so the PSEUDO_DMA macro is no longer needed. Also remove the spin counters used for debugging pseudo DMA drivers. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-04-11ncr5380: Disable the DMA errata workaround flag by defaultFinn Thain1-1/+1
The only chip that needs the workarounds enabled is an early NMOS device. That means that the common case is to disable them. Unfortunately the sense of the flag is such that it has to be set for the common case. Rename the flag so that zero can be used to mean "no errata workarounds needed". This simplifies the code. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-06ncr5380: Fix soft lockupsFinn Thain1-0/+1
Because of the rudimentary design of the chip, it is necessary to poll the SCSI bus signals during PIO and this tends to hog the CPU. The driver will accept new commands while others execute, and this causes a soft lockup because the workqueue item will not terminate until the issue queue is emptied. When exercising dmx3191d using sequential IO from dd, the driver is sent 512 KiB WRITE commands and 128 KiB READs. For a PIO transfer, the rate is is only about 300 KiB/s, so these are long-running commands. And although PDMA may run at several MiB/s, interrupts are disabled for the duration of the transfer. Fix the unresponsiveness and soft lockup issues by calling cond_resched() after each command is completed and by limiting max_sectors for drivers that don't implement real DMA. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-06ncr5380: Use standard list data structureFinn Thain1-0/+1
The NCR5380 drivers have a home-spun linked list implementation for scsi_cmnd structs that uses cmd->host_scribble as a 'next' pointer. Adopt the standard list_head data structure and list operations instead. Remove the eh_abort_handler rather than convert it. Doing the conversion would only be churn because the existing EH handlers don't work and get replaced in a subsequent patch. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-06ncr5380: Remove command list debug codeFinn Thain1-2/+0
Some NCR5380 hosts offer a .show_info method to access the contents of the various command list data structures from a procfs file. When NDEBUG is set, the same information is sent to the console during EH. The two core drivers, atari_NCR5380.c and NCR5380.c differ here. Because it is just for debugging, the easiest way to fix the discrepancy is simply remove this code. The only remaining users of NCR5380_show_info() and NCR5380_write_info() are drivers that define PSEUDO_DMA. The others have no use for the .show_info method, so don't initialize it. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-06ncr5380: Cleanup #include directivesFinn Thain1-2/+0
Remove unused includes (stat.h, signal.h, proc_fs.h) and move includes needed by the core drivers into the common header (delay.h etc). Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-06ncr5380: Implement NCR5380_dma_xfer_len and remove LIMIT_TRANSFERSIZE macroFinn Thain1-0/+2
Follow the example of the atari_NCR5380.c core driver and adopt the NCR5380_dma_xfer_len() hook. Implement NCR5380_dma_xfer_len() for dtc.c and g_NCR5380.c to take care of the limitations of these cards. Keep the default for drivers using PSEUDO_DMA. Eliminate the unused macro LIMIT_TRANSFERSIZE. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-06ncr5380: Introduce unbound workqueueFinn Thain1-2/+6
Allocate a work queue that will permit busy waiting and sleeping. This means NCR5380_init() can potentially fail, so add this error path. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-06ncr5380: Split NCR5380_init() into two functionsFinn Thain1-0/+2
This patch splits the NCR5380_init() function into two parts, similar to the scheme used with atari_NCR5380.c. This avoids two problems. Firstly, NCR5380_init() may perform a bus reset, which would cause the chip to assert IRQ. The chip is unable to mask its bus reset interrupt. Drivers can't call request_irq() before calling NCR5380_init(), because initialization must happen before the interrupt handler executes. If driver initialization causes an interrupt it may be problematic on some platforms. To avoid that, first move the bus reset code into NCR5380_maybe_reset_bus(). Secondly, NCR5380_init() contains some board-specific interrupt setup code for the NCR53C400 that does not belong in the core driver. In moving this code, better not re-order interrupt initialization and bus reset. Again, the solution is to move the bus reset code into NCR5380_maybe_reset_bus(). Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-01-06ncr5380: Remove NCR5380_local_declare and NCR5380_setup macrosFinn Thain1-4/+5
The NCR5380_local_declare and NCR5380_setup macros exist to define and initialize a particular local variable, to provide the address of the chip registers needed for the driver's implementation of its NCR5380_read/write register access macros. In cumana_1 and macscsi, these macros generate pointless code like this, struct Scsi_Host *_instance; _instance = instance; In pas16, the use of NCR5380_read/write in pas16_hw_detect() requires that the io_port local variable has been defined and initialized, but the NCR5380_local_declare and NCR5380_setup macros can't be used for that purpose because the Scsi_Host struct has not yet been instantiated. Moreover, these macros were removed from atari_NCR5380.c long ago and now they constitute yet another discrepancy between the two core driver forks. Remove these "optimizations". Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2014-11-20ncr5380: Drop legacy scsi.h includeFinn Thain1-1/+0
Convert Scsi_Cmnd to struct scsi_cmnd and drop the #include "scsi.h". The sun3_NCR5380.c core driver already uses struct scsi_cmnd so converting the other core drivers reduces the diff which makes them easier to unify. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Remove *_RELEASE macrosFinn Thain1-2/+0
The *_RELEASE macros don't tell me anything. In some cases the version in the macro contradicts the version in the comments. Anyway, the Linux kernel version is sufficient information. Remove these macros to improve readability. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Move static PDMA spin counters to host dataFinn Thain1-2/+0
Static variables from dtc.c and pas16.c should not appear in the core NCR5380.c driver. Aside from being a layering issue this worsens the divergence between the three core driver variants (atari_NCR5380.c and sun3_NCR5380.c don't support PSEUDO_DMA) and it can mean multiple hosts share the same counters. Fix this by making the pseudo DMA spin counters in the core more generic. This also avoids the abuse of the {DTC,PAS16}_PUBLIC_RELEASE macros, so they can be removed. oak.c doesn't use PDMA and hence it doesn't use the counters and hence it needs no write_info() method. Remove it. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Cleanup host info() methodsFinn Thain1-13/+1
If the host->info() method is not set, then host->name is used by default. For atari_scsi, that is exactly the same text. So remove the redundant info() method. Keep sun3_scsi.c in line with atari_scsi. Some NCR5380 drivers return an empty string from the info() method (arm/cumana_1.c arm/oak.c mac_scsi.c) while other drivers use the default (dmx3191d dtc.c g_NCR5380.c pas16.c t128.c). Implement a common info() method to replace a lot of duplicated code which the various drivers use to announce the same information. This replaces most of the (deprecated) show_info() output and all of the NCR5380_print_info() output. This also eliminates a bunch of code in g_NCR5380 which just duplicates functionality in the core driver. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Fix SCSI_IRQ_NONE bugsFinn Thain1-1/+1
Oak scsi doesn't use any IRQ, but it sets irq = IRQ_NONE rather than SCSI_IRQ_NONE. Problem is, the core NCR5380 driver expects SCSI_IRQ_NONE if it is to issue IDENTIFY commands that prevent target disconnection. And, as Geert points out, IRQ_NONE is part of enum irqreturn. Other drivers, when they can't get an IRQ or can't use one, will set host->irq = SCSI_IRQ_NONE (that is, 255). But when they exit they will attempt to free IRQ 255 which was never requested. Fix these bugs by using NO_IRQ in place of SCSI_IRQ_NONE and IRQ_NONE. That means IRQ 0 is no longer probed by ISA drivers but I don't think this matters. Setting IRQ = 255 for these ISA drivers is understood to mean no IRQ. This remains supported so as to avoid breaking existing ISA setups (which can be difficult to get working) and because existing documentation (SANE, TLDP etc) describes this usage for the ISA NCR5380 driver options. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Remove redundant AUTOSENSE macroFinn Thain1-1/+0
Every NCR5380 driver sets AUTOSENSE so it need not be optional (and the mid-layer expects it). Remove this redundant macro to improve readability. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-11-20ncr5380: Remove unused macrosFinn Thain1-1/+0
Some macros are never evaluated (i.e. FOO, USLEEP, SCSI2 and USE_WRAPPER; and in some drivers, NCR5380_intr and NCR5380_proc_info). DRIVER_SETUP serves no purpose anymore. Remove these macro definitions. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2014-05-28scsi/NCR5380: remove unused BOARD_NORMAL and BOARD_NCR53C400Finn Thain1-3/+0
BOARD_NORMAL is completely unused and BOARD_NCR53C400 is used only by g_NCR5380 internally. Remove the unused definitions. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Acked-by: Sam Creasey <sammy@sammy.net> Signed-off-by: Christoph Hellwig <hch@lst.de>
2013-04-09NCR5830: switch to ->show_info()Al Viro1-2/+4
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2013-01-03Drivers: scsi: remove __dev* attributes.Greg Kroah-Hartman1-4/+3
CONFIG_HOTPLUG is going away as an option. As a result, the __dev* markings need to be removed. This change removes the use of __devinit, __devexit_p, __devinitdata, __devinitconst, and __devexit from these drivers. Based on patches originally written by Bill Pemberton, but redone by me in order to handle some of the coding style issues better, by hand. Cc: Bill Pemberton <wfp5p@virginia.edu> Cc: Adam Radford <linuxraid@lsi.com> Cc: "James E.J. Bottomley" <JBottomley@parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-09SCSI: ARM: ncr5380/oak uses no interruptsArnd Bergmann1-0/+1
The ncr5380 driver is included by multiple board specific drivers, which may or may not use the interrupt handler. The oak variant doesn't, and should set the DONT_USE_INTR macro. Without this patch, building rpc_defconfig results in: drivers/scsi/arm/../NCR5380.c:1160:20: warning: 'oakscsi_intr' defined but not used [-Wunused-function] Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: "James E.J. Bottomley" <JBottomley@parallels.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-scsi@vger.kernel.org
2012-03-28Remove all #inclusions of asm/system.hDavid Howells1-1/+0
Remove all #inclusions of asm/system.h preparatory to splitting and killing it. Performed with the following command: perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *` Signed-off-by: David Howells <dhowells@redhat.com>
2007-07-20[ARM] rpc: update Acorn SCSI drivers to modern ecard interfacesRussell King1-30/+44
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-02-14[PATCH] remove many unneeded #includes of sched.hTim Schmielau1-1/+0
After Al Viro (finally) succeeded in removing the sched.h #include in module.h recently, it makes sense again to remove other superfluous sched.h includes. There are quite a lot of files which include it but don't actually need anything defined in there. Presumably these includes were once needed for macros that used to live in sched.h, but moved to other header files in the course of cleaning it up. To ease the pain, this time I did not fiddle with any header files and only removed #includes from .c-files, which tend to cause less trouble. Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha, arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig, allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all configs in arch/arm/configs on arm. I also checked that no new warnings were introduced by the patch (actually, some warnings are removed that were emitted by unnecessarily included header files). Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2005-11-09[SCSI] remove Scsi_Host_Template typedefChristoph Hellwig1-1/+1
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-06-17[SCSI] Remove no-op implementations of SCSI EH hooksJeff Garzik1-2/+0
Drivers need not implement a hook that returns FAILED, and does nothing else, since the SCSI midlayer code will do that for us. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-04-16Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds1-0/+217
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-06 15:50:15 +0000