| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add new trace points for the start and end of enabling bypass on a
regulator, to allow monitoring of when regulators are moved into bypass
and how long that takes.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200529152216.9671-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
<m.szyprowski@samsung.com>:
Hi!
This patchset is another attempt to fix the regulator coupling on
Exynos5800/5422 SoCs. Here are links to the previous attempts:
https://lore.kernel.org/linux-samsung-soc/20191008101709.qVNy8eijBi0LynOteWFMnTg4GUwKG599n6OyYoX1Abs@z/
https://lore.kernel.org/lkml/20191017102758.8104-1-m.szyprowski@samsung.com/
https://lore.kernel.org/linux-pm/cover.1589528491.git.viresh.kumar@linaro.org/
https://lore.kernel.org/linux-pm/20200528131130.17984-1-m.szyprowski@samsung.com/
The problem is with "vdd_int" regulator coupled with "vdd_arm" on Odroid
XU3/XU4 boards family. "vdd_arm" is handled by CPUfreq. "vdd_int" is
handled by devfreq. CPUfreq initialized quite early during boot and it
starts changing OPPs and "vdd_arm" value. Sometimes CPU activity during
boot goes down and some low-frequency OPPs are selected, what in turn
causes lowering "vdd_arm". This happens before devfreq applies its
requirements on "vdd_int". Regulator balancing code reduces "vdd_arm"
voltage value, what in turn causes lowering "vdd_int" value to the lowest
possible value. This is much below the operation point of the wcore bus,
which still runs at the highest frequency.
The issue was hard to notice because in the most cases the board managed
to boot properly, even when the regulator was set to lowest value allowed
by the regulator constraints. However, it caused some random issues,
which can be observed as "Unhandled prefetch abort" or low USB stability.
Adding more and more special cases to the generic code has been rejected,
so the only way to ensure the desired behavior on Exynos5800-based SoCs
is to make a custom regulator coupler driver.
Best regards,
Marek Szyprowski
Patch summary:
Marek Szyprowski (2):
regulator: extract voltage balancing code to separate function
soc: samsung: Add simple voltage coupler for Exynos5800
arch/arm/mach-exynos/Kconfig | 1 +
drivers/regulator/core.c | 49 ++++++++-------
drivers/soc/samsung/Kconfig | 3 +
drivers/soc/samsung/Makefile | 1 +
.../soc/samsung/exynos-regulator-coupler.c | 59 +++++++++++++++++++
include/linux/regulator/coupler.h | 8 +++
6 files changed, 101 insertions(+), 20 deletions(-)
create mode 100644 drivers/soc/samsung/exynos-regulator-coupler.c
--
2.17.1
base-commit: 8f3d9f354286745c751374f5f1fcafee6b3f3136
|
|
Move the coupled regulators voltage balancing code to the separate
function and allow to call it from the custom regulator couplers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200529124940.10675-2-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Vaittinen <matti.vaittinen@fi.rohmeurope.com>:
Add maintainer entries to a few ROHM devices and Linear Ranges
Linear Ranges helpers were refactored out of regulator core to lib so
that other drivers could utilize them too. (I guess power/supply drivers
and possibly clk drivers can benefit from them). As regulators is
currently the main user it makes sense the changes to linear_ranges go
through Mark's tree.
During past two years few ROHM PMIC drivers have been added to
mainstream. They deserve a supporter from ROHM side too :)
Patch 1:
Maintainer entries for few ROHM IC drivers
Patch 2:
Maintainer entry for linear ranges helpers
---
Matti Vaittinen (2):
MAINTAINERS: Add entry for ROHM power management ICs
MAINTAINERS: Add maintainer entry for linear ranges helper
MAINTAINERS | 37 +++++++++++++++++++++++++++++++++++++
1 file changed, 37 insertions(+)
base-commit: b9bbe6ed63b2b9f2c9ee5cbd0f2c946a2723f4ce
--
2.21.0
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
|
|
regulator_init_complete_work"
This reverts commit dca0b44957e5 ("regulator: Use
driver_deferred_probe_timeout for regulator_init_complete_work"),
as we ended up reverting the default deferred_probe_timeout
value back to zero, to preserve behavior with 5.6 we need to
decouple the regulator timeout which was previously 30 seconds.
This avoids breaking some systems that depend on the regulator
timeout but don't require the deferred probe timeout.
Cc: linux-pm@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Rob Herring <robh@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200429172349.55979-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make it easier to identify regulator consumers when consumer device
uses more than one supply.
Before:
regulator ena use open bypass voltage current min max
-----------------------------------------------------------------------------------
regulator-dummy 1 0 2 0 0mV 0mA 0mV 0mV
1-0010 0mV 0mV
1-0010 0mV 0mV
After:
regulator ena use open bypass voltage current min max
-----------------------------------------------------------------------------------
regulator-dummy 1 0 2 0 0mV 0mA 0mV 0mV
1-0010-vccio 0mV 0mV
1-0010-vcc33 0mV 0mV
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/731a4b299c6ae0ee9d8995157600a3477f21a36c.1585959068.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi and regulator updates from Mark Brown:
"At one point in the release cycle I managed to fat finger things and
apply some SPI fixes onto a regulator branch and merge that into the
SPI tree, then pull in a change shared with the MTD tree moving the
Mediatek quadspi driver over to become the Mediatek spi-nor driver in
the SPI tree.
This has made a mess which I only just noticed while preparing this
and I can't see a sensible way to unpick things due to other
subsequent merge commits especially the pull from MTD so it looks like
the most sensible thing to do is give up and combine the two pull
requests.
Fortunately both subsystems were fairly quiet this cycle, the
highlights are:
regulator:
- Support for Monoloithic Power Systems MP5416, MP8867 and MPS8869
and Qualcomm PMI8994 and SMB208.
SPI:
- Lots of enhancements for spi-fsl-dspi, including XSPI mode support,
from Vladimir Oltean.
- Support for amlogic Meson G12A, IBM FSI, Mediatek spi-nor (moved
from MTD), NXP i.MX8Mx, Rockchip PX30, RK3308 and RK3328, and
Qualcomm Atheros AR934x/QCA95xx"
* tag 'regulator-spi-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (118 commits)
spi: efm32: Convert to use GPIO descriptors
regulator: qcom_smd: Add pmi8994 regulator support
regulator: da9063: Fix get_mode() functions to read sleep field
spi: spi-fsl-lpspi: Replace zero-length array with flexible-array member
spi: spi-s3c24xx: Replace zero-length array with flexible-array member
spi: stm32: Fix comments compilation warnings
spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses
spi: spi-fsl-dspi: Add support for LS1028A
spi: spi-fsl-dspi: Move invariant configs out of dspi_transfer_one_message
spi: spi-fsl-dspi: Fix interrupt-less DMA mode taking an XSPI code path
spi: spi-fsl-dspi: Avoid NULL pointer in dspi_slave_abort for non-DMA mode
spi: spi-fsl-dspi: Replace interruptible wait queue with a simple completion
spi: spi-fsl-dspi: Protect against races on dspi->words_in_flight
spi: spi-fsl-dspi: Avoid reading more data than written in EOQ mode
spi: spi-fsl-dspi: Fix bits-per-word acceleration in DMA mode
spi: spi-fsl-dspi: Fix little endian access to PUSHR CMD and TXDATA
spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR
regulator: driver.h: fix regulator_map_* function names
regulator: da9063: fix suspend
spi: mxs: Drop GPIO includes
...
|
|
With current code:
st-gyro-i2c i2c-PRP0001:00: i2c-PRP0001:00 supply vdd not found, using dummy regulator
which looks a bit oververbose.
Replace this with simplified format string for the above case, and drop
"deviceless" case since for all dev_*() macros used in _regulator_get()
the "(null)" will be printed anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200312183245.1612-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The regulator_init_complete_work logic defers the cleanup for an
arbitrary 30 seconds of time to allow modules loaded by userland
to start.
This arbitrary timeout is similar to the
driver_deferred_probe_timeout value, and its been suggested we
align these so users have a method to extend the timeouts as
needed.
So this patch changes the logic to use the
driver_deferred_probe_timeout value for the delay value if it
is set (using a delay of 0 if it is not).
Cc: linux-pm@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200225050828.56458-7-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
Change the exported symbols introduced by commit e9153311491da
("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
from EXPORT_SYMBOL() to EXPORT_SYMBOL_GPL(), like is used for all the core
parts.
Fixes: e9153311491da ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200120123921.1204339-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
`cat /sys/kernel/debug/regulator/regulator_summary` ends on a deadlock
when you have a voltage controlled regulator (vctrl).
The problem is that the vctrl_get_voltage() and vctrl_set_voltage() calls the
regulator_get_voltage() and regulator_set_voltage() and that will try to lock
again the dependent regulators (the regulator supplying the control voltage).
Fix the issue by exporting the unlocked version of the regulator_get_voltage()
and regulator_set_voltage() API so drivers that need it, like the voltage
controlled regulator driver can use it.
Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking")
Reported-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200116094543.2847321-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small set of fixes for mostly minor issues here, the only real code
ones are Wen Yang's fixes for error handling in the core and Christian
Marussi's list_voltage() change which is a fix for disruptively bad
performance for regulators with continuous voltage control (which are
rare)"
* tag 'regulator-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: rn5t618: fix module aliases
regulator: max77650: add of_match table
regulator: core: avoid unneeded .list_voltage calls
regulator: s5m8767: Fix a warning message
regulator: core: fix regulator_register() error paths to properly release rdev
regulator: fix use after free issue
|
|
Inside machine_constraints_voltage() a loop is in charge of verifying that
each of the defined voltages are within the configured constraints and
that those constraints are in fact compatible with the available voltages'
list.
When the registered regulator happens to be defined with a wide range of
possible voltages the above O(n) loop can be costly.
Moreover since this behaviour is triggered during the registration process,
it means also that it can be easily triggered at probe time, slowing down
considerably some module loading.
On the other side if such wide range of voltage values happens to be also
continuous and without discontinuity of any kind, the above potentially
cumbersome operation is also useless.
For these reasons, avoid such .list_voltage poll loop when regulator is
described as 'continuous_voltage_range' as is, indeed, similarly already
done inside regulator_is_supported_voltage().
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20191209125239.46054-1-cristian.marussi@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are several issues with the error handling code of
the regulator_register() function:
ret = device_register(&rdev->dev);
if (ret != 0) {
put_device(&rdev->dev); --> rdev released
goto unset_supplies;
}
...
unset_supplies:
...
unset_regulator_supplies(rdev); --> use-after-free
...
clean:
if (dangling_of_gpiod)
gpiod_put(config->ena_gpiod);
kfree(rdev); --> double free
We add a variable to record the failure of device_register() and
move put_device() down a bit to avoid the above issues.
Fixes: c438b9d01736 ("regulator: core: Move registration of regulator device")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191201030250.38074-1-wenyang@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is caused by dereferencing 'rdev' after put_device() in
the _regulator_get()/_regulator_put() functions.
This patch just moves the put_device() down a bit to avoid the
issue.
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191124145835.25999-1-wenyang@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
Boot-on regulators are always kept on because their use_count value
is now incremented at boot time and never cleaned.
Only increment count value for alway-on regulators.
regulator_late_cleanup() is now able to power off boot-on regulators
when unused.
Fixes: 05f224ca6693 ("regulator: core: Clean enabling always-on regulators + their supplies")
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Link: https://lore.kernel.org/r/20191113102737.27831-1-p.paillet@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
device_link_add() might not always succeed depending on the type of
device link and the rest of the dependencies in the system. If
device_link_add() didn't succeed, then we shouldn't try to remove the
link later on as it might remove a link someone else created.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20191115000438.45970-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The generic voltage balancer doesn't work correctly if one of regulator
couples turns off. Currently there are no users in kernel for that case,
although let's explicitly show that this case is unsupported for those who
will try to use that feature.
Link: https://lore.kernel.org/linux-samsung-soc/20191008170503.yd6GscYPLxjgrXqDuCO7AJc6i6egNZGJkVWHLlCxvA4@z/
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20191025002240.25288-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch fixes memory leak which should happen if regulator's coupling
fails to initialize.
Fixes: d8ca7d184b33 ("regulator: core: Introduce API for regulators coupling customization")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20191025002240.25288-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sometimes it can happen that the regulator_of_get_init_data() can't
retrieve the config due to a not probed device the regulator depends on.
Fix that by checking the return value of of_parse_cb() and return
EPROBE_DEFER in such cases.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-4-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
regulator_uV_show() is missing error handling if regulator_get_voltage_rdev()
returns negative values. Instead it prints the errno as a string, e.g. -EINVAL
as "-22" which could be interpreted as -22 µV.
We also do not need to hold the lock while converting the integer to a string.
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/f37f2a1276efcb34cf3b7f1a25481175be048806.1568143348.git.hns@goldelico.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The kernel has no way of knowing when we have finished instantiating
drivers, between deferred probe and systems that build key drivers as
modules we might be doing this long after userspace has booted. This has
always been a bit of an issue with regulator_init_complete since it can
power off hardware that's not had it's driver loaded which can result in
user visible effects, the main case is powering off displays. Practically
speaking it's not been an issue in real systems since most systems that
use the regulator API are embedded and build in key drivers anyway but
with Arm laptops coming on the market it's becoming more of an issue so
let's do something about it.
In the absence of any better idea just defer the powering off for 30s
after late_initcall(), this is obviously a hack but it should mask the
issue for now and it's no more arbitrary than late_initcall() itself.
Ideally we'd have some heuristics to detect if we're on an affected
system and tune or skip the delay appropriately, and there may be some
need for a command line option to be added.
Link: https://lore.kernel.org/r/20190904124250.25844-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
Cc: stable@vger.kernel.org
|
|
In function of_get_child_regulator(), the loop for_each_child_of_node()
contains two mid-loop return statements, each preceded by a statement
putting child. In order to reduce this repetition, create a new label,
err_node_put, that puts child and then returns the required value;
edit the mid-loop return blocks to instead go to this new label.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815053704.32156-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804162023.5673-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
|
|
|
|
Some regulators require that the requested voltage be reached gradually
by setting all or some of the intermediate values. Implement a new field
in the regulator description struct that allows users to specify the
number of selectors by which the regulator API should step when ramping
the voltage up/down.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190703161035.31808-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Expose some of internal functions that are required for implementation of
customized regulator couplers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Right now regulator core supports only one type of regulators coupling,
the "voltage max-spread" which keeps voltages of coupled regulators in a
given range from each other. A more sophisticated coupling may be required
in practice, one example is the NVIDIA Tegra SoCs which besides the
max-spreading have other restrictions that must be adhered. Introduce API
that allow platforms to provide their own customized coupling algorithms.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Makes things look more consistent.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Linux 5.2-rc4
|
|
The conversion here is really trivial: just a bunch of title
markups and very few puntual changes is enough to make it to
be parsed by Sphinx and generate a nice html.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The logic is equivalent, but it looks more straightforward this way:
If rdev->desc->ops->enable_time is set, call it.
Otherwise fallback to return rdev->desc->enable_time.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
All the current clients of this API assume that 0 corresponds
to a failure and non-zero to a pass therefore ignoring the need to
handle a negative error code.
This commit modifies the API to follow that standard since returning a
negative (EINVAL) doesn't seem to provide enough value to justify
the need to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Temporary failures to get a regulator (EPROBE_DEFER) should be logged
as debug information instead of errors.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
I went to great lengths to hand over the management of the GPIO
descriptors to the regulator core, and some stray rebased
oneliner in the old patch must have been assuming the devices
were still doing devres management of it.
We handed the management over to the regulator core, so of
course the regulator core shall issue gpiod_put() when done.
Sorry for the descriptor leak.
Fixes: 541d052d7215 ("regulator: core: Only support passing enable GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Lockdep reports the following issue on my setup:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock((work_completion)(&(&rdev->disable_work)->work));
lock(regulator_list_mutex);
lock((work_completion)(&(&rdev->disable_work)->work));
lock(regulator_list_mutex);
The problem is that regulator_unregister takes the
regulator_list_mutex and then calls flush_work on disable_work. But
regulator_disable_work calls regulator_lock_dependent which will
also take the regulator_list_mutex. Resulting in a deadlock if the
flush_work call actually needs to flush the work.
Fix this issue by moving the flush_work outside of the
regulator_list_mutex. The list mutex is not used to guard the point at
which the delayed work is queued, so its use adds no additional safety.
Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During several error paths in the function
regulator_set_voltage_unlocked() the value of 'ret' can take on negative
error values. However, in calls that go through the 'goto out' statement,
this return value is lost and return 0 is used instead, indicating a
'pass'.
There are several cases where this function should legitimately return a
fail instead of a pass: one such case includes constraints check during
voltage selection in the call to regulator_check_voltage(), which can
have -EINVAL for the case when an unsupported voltage is incorrectly
requested. In that case, -22 is expected as the return value, not 0.
Fixes: 9243a195be7a ("regulator: core: Change voltage setting path")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
drms_uA_update()"
[The original commit was sent against -next but needed to be sent as a
bugfix, however -next had some additional changes which needed to be
reverted. Now everything is all in one branch applying the rest of the
changes to fix up the merge issue -- broonie]
commit e5e21f70bfd3 ("regulator: core: Take lock before applying system
load") took the regulator lock before calling drms_uA_update() in order
to silence a lockdep warning during regulator_register().
However, we are not supposed to need locks at this point as the regulator
is in the process of being registered, so there should be no possibility
of concurrent access.
Instead, remove the unnecessary locking and simply drop the lockdep
annotation, since it is no longer valid.
Fixes: e5e21f70bfd3 ("regulator: core: Take lock before applying system load")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When REGULATOR_CHANGE_DRMS is not set, drms_uA_update is a no-op.
It used to print a debug message, which was dropped in commit
8a34e979f684 ("regulator: refactor valid_ops_mask checking code")
Let's bring the debug message back, because it helps find missing
regulator-allow-set-load properties.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
commit e5e21f70bfd3 ("regulator: core: Take lock before applying system
load") took the regulator lock before calling drms_uA_update() in order
to silence a lockdep warning during regulator_register().
However, we are not supposed to need locks at this point as the regulator
is in the process of being registered, so there should be no possibility
of concurrent access.
Instead, remove the unnecessary locking and simply drop the lockdep
annotation, since it is no longer valid.
Fixes: e5e21f70bfd3 ("regulator: core: Take lock before applying system load")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is a remnant of commit 70a7fb80e85a ("regulator: core: Fix nested
locking of supplies").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Take the regulator lock before applying system load.
Fixes the following lockdep splat:
[ 5.583581] WARNING: CPU: 1 PID: 16 at drivers/regulator/core.c:925 drms_uA_update+0x114/0x360
[ 5.588467] Modules linked in:
[ 5.596833] CPU: 1 PID: 16 Comm: kworker/1:0 Not tainted 5.0.0-rc6-next-20190213-00002-g0fce66ab480f #18
[ 5.599933] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
[ 5.609544] Workqueue: events qcom_channel_state_worker
[ 5.616209] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 5.621152] pc : drms_uA_update+0x114/0x360
[ 5.626006] lr : drms_uA_update+0x110/0x360
[ 5.630084] sp : ffff0000124b3490
[ 5.634242] x29: ffff0000124b3490 x28: ffff800005326e00
[ 5.637735] x27: ffff0000124b35f8 x26: 000000000032bc48
[ 5.643117] x25: ffff800004c7e800 x24: ffff800004c6d500
[ 5.648411] x23: ffff800004c38a80 x22: 00000000000000d1
[ 5.653706] x21: 00000000001ab3f0 x20: ffff800004c7e800
[ 5.659001] x19: ffff0000114c3000 x18: ffffffffffffffff
[ 5.664297] x17: 0000000000000000 x16: 0000000000000000
[ 5.669592] x15: ffff0000114c3808 x14: 0720072007200720
[ 5.674888] x13: 00000000199c9b28 x12: ffff80002bcccc40
[ 5.680183] x11: ffff000012286000 x10: ffff0000114c3808
[ 5.685477] x9 : 0720072007200720 x8 : ffff000010e9e808
[ 5.690772] x7 : ffff0000106da568 x6 : 0000000000000000
[ 5.696067] x5 : 0000000000000000 x4 : 0000000000000000
[ 5.701362] x3 : 0000000000000004 x2 : 0000000000000000
[ 5.706658] x1 : 0000000000000000 x0 : 0000000000000000
[ 5.711952] Call trace:
[ 5.717223] drms_uA_update+0x114/0x360
[ 5.719405] regulator_register+0xb30/0x1140
[ 5.723230] devm_regulator_register+0x4c/0xa8
[ 5.727745] rpm_reg_probe+0xfc/0x1b0
[ 5.731992] platform_drv_probe+0x50/0xa0
[ 5.735727] really_probe+0x20c/0x2b8
[ 5.739718] driver_probe_device+0x58/0x100
[ 5.743368] __device_attach_driver+0x90/0xd0
[ 5.747363] bus_for_each_drv+0x64/0xc8
[ 5.751870] __device_attach+0xd8/0x138
[ 5.755516] device_initial_probe+0x10/0x18
[ 5.759341] bus_probe_device+0x98/0xa0
[ 5.763502] device_add+0x3d0/0x640
[ 5.767319] of_device_add+0x48/0x58
[ 5.770793] of_platform_device_create_pdata+0xb0/0x128
[ 5.774629] of_platform_bus_create+0x174/0x370
[ 5.779569] of_platform_populate+0x78/0xe0
[ 5.784082] qcom_smd_rpm_probe+0x80/0xa0
[ 5.788245] rpmsg_dev_probe+0x114/0x1a0
[ 5.792411] really_probe+0x20c/0x2b8
[ 5.796401] driver_probe_device+0x58/0x100
[ 5.799964] __device_attach_driver+0x90/0xd0
[ 5.803960] bus_for_each_drv+0x64/0xc8
[ 5.808468] __device_attach+0xd8/0x138
[ 5.812115] device_initial_probe+0x10/0x18
[ 5.815936] bus_probe_device+0x98/0xa0
[ 5.820099] device_add+0x3d0/0x640
[ 5.823916] device_register+0x1c/0x28
[ 5.827391] rpmsg_register_device+0x4c/0x90
[ 5.831216] qcom_channel_state_worker+0x170/0x298
[ 5.835651] process_one_work+0x294/0x6e8
[ 5.840241] worker_thread+0x40/0x450
[ 5.844318] kthread+0x11c/0x120
[ 5.847961] ret_from_fork+0x10/0x18
[ 5.851260] irq event stamp: 9090
[ 5.854820] hardirqs last enabled at (9089): [<ffff000010160798>] console_unlock+0x3e0/0x5b0
[ 5.858086] hardirqs last disabled at (9090): [<ffff0000100817cc>] do_debug_exception+0x104/0x140
[ 5.866596] softirqs last enabled at (9086): [<ffff000010082024>] __do_softirq+0x474/0x574
[ 5.875446] softirqs last disabled at (9079): [<ffff0000100f2254>] irq_exit+0x13c/0x148
[ 5.883598] ---[ end trace 6984ef7f081afa21 ]---
Fixes: fa94e48e13a1 ("regulator: core: Apply system load even if no consumer loads")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Device links are refcounted, device_link_remove() has to be called as
many times as device_link_add().
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that we changed all providers to pass descriptors into the core
for enable GPIOs instead of a global GPIO number, delete the support
for passing GPIO numbers in, and we get a cleanup and size reduction
in the core, and from a GPIO point of view we use the modern, cleaner
interface.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
