summaryrefslogtreecommitdiffstats
path: root/drivers/pinctrl/pinctrl-rockchip.c
AgeCommit message (Collapse)AuthorFilesLines
2017-10-31pinctrl: rockchip: Add iomux-route switching support for rk3288Heiko Stuebner1-0/+20
The rk3288 also has one function that can be routed to one of two pins, the hdmi cec functionality can use either gpio7c0 or gpio7c7. So add the route switching support for it. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Hans Verkuil <hans.verkuil@cisco.com> Reviewed-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-07pinctrl: rockchip: rk3328: Fix the correct routing configDavid Wu1-2/+9
If the gmac-m1 optimization(bit10) is selected, the gpio function of gmac pins is not valid. We may use the rmii mode for gmac interface, the pins such as rx_d2, rx_d3, which the rgmii mode used, but rmii not used could be taken as gpio function. So gmac_rxd0m1 selects the bit2, and gmac_rxd0m3 select bit10 is more correct. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-10-07pinctrl: rockchip: Fix the rk3399 gpio0 and gpio1 banks' drv_offset at pmu grfDavid Wu1-6/+6
The offset of gpio0 and gpio1 bank drive strength is 0x8, not 0x4. But the mux is 0x4, we couldn't use the IOMUX_WIDTH_4BIT flag, so we give them actual offset. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-31pinctrl: rockchip: Add rv1108 recalculated iomux supportDavid Wu1-1/+67
The pins from GPIO1A0 to GPIO1B1 are special, need to recalculate iomux. And the register offset is larger than the u8 range, so changed to u32. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14pinctrl: rockchip: add input schmitt support for rv1108Andy Yan1-0/+31
Some pins like i2c SCL/SDA need the schmitt input function to avoid crosstalk problems. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14pinctrl: rockchip: Add rk3128 pinctrl supportDavid Wu1-0/+129
There are 3 IP blocks pin routes need to be switched, that are emmc-cmd, spi, i2s. And there are some pins need to be recalced, which are gpio2c4~gpio2c7 and gpio2d0. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14pinctrl: rockchip: Use common interface for recalced iomuxDavid Wu1-39/+50
The other Socs also need the feature of recalced iomux, so make it as a common interface like iomux route feature. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-07-06Merge tag 'pinctrl-v4.13-1' of ↵Linus Torvalds1-12/+331
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the big bulk of pin control changes for the v4.13 series: Core: - The documentation is moved over to RST. - We now have agreed bindings for enabling input and output buffers without actually enabling input and/or output on a pin. We are chiseling out some details of pin control electronics. New drivers: - ZTE ZX - Renesas RZA1 - MIPS Ingenic JZ47xx: also switch over existing drivers in the tree to use this pin controller and consolidate earlier spread out code. - Microschip MCP23S08: this driver is migrated from the GPIO subsystem and totally rewritten to use proper pin control. All users are switched over. New subdrivers: - Renesas R8A7743 and R8A7745. - Allwinner Sunxi A83T R_PIO. - Marvell MVEBU Armada CP110 and AP806. - Intel Cannon Lake PCH. - Qualcomm IPQ8074. Notable improvements: - IRQ support on the Marvell MVEBU Armada 37xx. - Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM. - Rockchip driver now supports iomux-route switching for RK3228, RK3328 and RK3399. - Rockchip A10 and A20 are merged into a single driver. - STM32 has improved GPIO support. - Samsung Exynos drivers are split per ARMv7 and ARMv8. - Marvell MVEBU is converted to use regmap for register access. Maintenance: - Several Renesas SH-PFC refactorings and updates. - Serious code size cut for Mediatek MT7623. - Misc janitorial and MAINTAINERS fixes" * tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits) pinctrl: samsung: Remove bogus irq_[un]mask from resource management pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static pinctrl: rza1: Remove unneeded wrong check for wrong variable pinctrl: qcom: Add ipq8074 pinctrl driver pinctrl: freescale: imx7d: make of_device_ids const. pinctrl: DT: extend the pinmux property to support integers array pinctrl: generic: Add output-enable property pinctrl: armada-37xx: Fix number of pin in sdio_sb pinctrl: armada-37xx: Fix uart2 group selection register mask pinctrl: bcm2835: Avoid warning from __irq_do_set_handler pinctrl: sh-pfc: r8a7795: Add PWM support MAINTAINERS: Add Qualcomm pinctrl drivers section arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header dt-bindings: pinctrl: Add RZ/A1 bindings doc pinctrl: Renesas RZ/A1 pin and gpio controller pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups pinctrl.txt: move it to the driver-api book pinctrl: ingenic: checking for NULL instead of IS_ERR() pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20 pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11 ...
2017-06-29Revert "pinctrl: rockchip: avoid hardirq-unsafe functions in irq_chip"Brian Norris1-40/+4
This reverts commit 88bb94216f59e10802aaf78c858a4146085faf18. It introduced a new CONFIG_DEBUG_ATOMIC_SLEEP warning in v4.12-rc1: [ 7226.716713] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238 [ 7226.716716] in_atomic(): 0, irqs_disabled(): 0, pid: 1708, name: bash [ 7226.716722] CPU: 1 PID: 1708 Comm: bash Not tainted 4.12.0-rc6+ #1213 [ 7226.716724] Hardware name: Google Kevin (DT) [ 7226.716726] Call trace: [ 7226.716738] [<ffffff8008089928>] dump_backtrace+0x0/0x24c [ 7226.716743] [<ffffff8008089b94>] show_stack+0x20/0x28 [ 7226.716749] [<ffffff8008371370>] dump_stack+0x90/0xb0 [ 7226.716755] [<ffffff80080cd2a0>] ___might_sleep+0x10c/0x124 [ 7226.716760] [<ffffff80080cd330>] __might_sleep+0x78/0x88 [ 7226.716765] [<ffffff800879e210>] mutex_lock+0x2c/0x64 [ 7226.716771] [<ffffff80083ad678>] rockchip_irq_bus_lock+0x30/0x3c [ 7226.716777] [<ffffff80080f6d40>] __irq_get_desc_lock+0x78/0x98 [ 7226.716782] [<ffffff80080f7e6c>] irq_set_irq_wake+0x44/0x12c [ 7226.716787] [<ffffff8008486e18>] dev_pm_arm_wake_irq+0x4c/0x58 [ 7226.716792] [<ffffff800848b80c>] device_wakeup_arm_wake_irqs+0x3c/0x58 [ 7226.716796] [<ffffff80084896fc>] dpm_suspend_noirq+0xf8/0x3a0 [ 7226.716800] [<ffffff80080f1384>] suspend_devices_and_enter+0x1a4/0x9a8 [ 7226.716803] [<ffffff80080f21ec>] pm_suspend+0x664/0x6a4 [ 7226.716807] [<ffffff80080f04d8>] state_store+0xd4/0xf8 ... It was reported on -rc1, and it's still not fixed in -rc6, so it should just be reverted. Cc: John Keeping <john@metanate.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-29pinctrl: rockchip: Add iomux-route switching support for rk3399David Wu1-0/+41
There are 2 IP blocks pin routes need to be switched, that are uart2dbg, pcie_clkreq. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-29pinctrl: rockchip: Add iomux-route switching support for rk3328David Wu1-0/+83
There are 8 IP blocks pin routes need to be switched, that are uart2dbg, gmac-m1-optimized, pdm, spi, i2s2, card, tsp, cif. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-29pinctrl: rockchip: Add iomux-route switching support for rk3228David Wu1-0/+132
There are 9 IP blocks pin routes need to be switched, that are pwm-0, pwm-1, pwm-2, pwm-3, sdio, spi, emmc, uart2, uart1. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-29pinctrl: rockchip: Add iomux-route switching supportDavid Wu1-1/+64
On the some rockchip SOCS, some things like rk3399 specific uart2 can use multiple pins. Somewhere between the pin io-cells and the uart it seems to have some sort of switch to decide to which pin to actually route the data. +-------+ +--------+ /- GPIO4_B0 (pinmux 2) | uart2 | -- | switch | --- GPIO4_C0 (pinmux 2) +-------+ +--------+ \- GPIO4_C3 (pinmux 2) (switch selects one of the 3 pins base on the GRF_SOC_CON7[BIT0, BIT1]) The routing switch is determined by one pin of a specific group to be set to its special pinmux function. If the pinmux setting is wrong for that pin the ip block won't work correctly anyway. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-22pinctrl: rockchip: remove unneeded (void *) casts in of_match_tableMasahiro Yamada1-11/+11
of_device_id::data is an opaque pointer. No explicit cast is needed. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-28pinctrl: rockchip: avoid hardirq-unsafe functions in irq_chipJohn Keeping1-4/+40
With real-time preemption, regmap functions cannot be used in the implementation of irq_chip since they use spinlocks which may sleep. Move the setting of the mux for IRQs to an irq_bus_sync_unlock handler where we are allowed to sleep. Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-28pinctrl: rockchip: split out verification of mux settingsJohn Keeping1-16/+30
We need to avoid calling regmap functions from irq handlers, so the next commit is going to move the call to rockchip_set_mux() into an irq_bus_sync_unlock handler. But we can't return an error from there so we still need to check the settings from rockchip_irq_set_type() and we will use this new rockchip_verify_mux() function from there. Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-28pinctrl: rockchip: convert to raw spinlockJohn Keeping1-13/+13
This lock is used from rockchip_irq_set_type() which is part of the irq_chip implementation and thus must use raw_spinlock_t as documented in Documentation/gpio/driver.txt. Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-28pinctrl: rockchip: remove unnecessary lockingJohn Keeping1-31/+2
regmap_update_bits does its own locking and everything else accessed here is a local variable so there is no need to lock around it. Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-23pinctrl: rockchip: rename RK1108 to RV1108Andy Yan1-38/+38
Rockchip finally named the SOC as RV1108, so change it. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> [adapted rk1108 dtsi to keep bisectability] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-23pinctrl: rockchip: add irq_enable & irq_disable opsJeffy Chen1-5/+6
Currently we are trying to enable/disable the clk of irq's gpio bank when unmask/mask irq. But the kernel's "lazy disable approach" will skip masking irq when the irq chip doesn't support irq_disable ops. So we may hit this case: irq_enable-> enable clk irq_disable-> noop irq_enable-> enable clk again irq_disable-> noop Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-14pinctrl: rockchip: Add input schmitt support for rk3328david.wu1-0/+23
Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-14pinctrl: rockchip：Add input schmitt supportdavid.wu1-0/+73
To prevent external signal crosstalk, some pins need to enable input schmitt, like i2c pins, 32k-input pin and so on. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-14pinctrl: rockchip: Add rk3328 pinctrl supportdavid.wu1-0/+70
Note, the iomux of following pins are special, need to be recalculated specially. - gpio2_b4 - gpio2_b7 - gpio2_c7 Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-14pinctrl: rockchip: Add mux recalculation supportdavid.wu1-6/+35
Some pins are special at a bank so that add IOMUX_RECALCED type to indicate which iomux source of the bank need to be recalculated. If the mux recalculateed callback and IOMUX_RECALCED type were set, recalculate the pins' iomux by using mux recalculated data struct. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-14pinctrl: rockchip: Add 3bit width mux supportdavid.wu1-3/+17
This patch supports 3bit width iomux type. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-26pinctrl: Widen the generic pinconf argument from 16 to 24 bitsMika Westerberg1-1/+1
The current pinconf packed format allows only 16-bit argument limiting the maximum value 65535. For most types this is enough. However, debounce time can be in range of hundreths of milliseconds in case of mechanical switches so we cannot represent the worst case using the current format. In order to support larger values change the packed format so that the lower 8 bits are used as type which leaves 24 bits for the argument. This allows representing values up to 16777215 and debounce times up to 16 seconds. We also convert the existing users to use 32-bit integer when extracting argument from the packed configuration value. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-16pinctrl: rockchip: add support for rk1108Andy Yan1-0/+86
This add pinctrl support for Rockchip RK1108 Soc. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Series-changes: 2 - add pull and drive-strength functionality Series-changes: 3 - two minor CodingStyle fixes adviced by Heiko Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-08-27pinctrl: rockchip: make it explicitly non-modularPaul Gortmaker1-6/+1
The Kconfig currently controlling compilation of this code is: drivers/pinctrl/Kconfig:config PINCTRL_ROCKCHIP drivers/pinctrl/Kconfig: bool ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modular infrastructure use, so that when reading the driver there is no doubt it is builtin-only. Note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Heiko Stuebner <heiko@sntech.de> Cc: linux-gpio@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-06-23pinctrl: rockchip: make rockchip_irq_gc_mask_set_bit staticBen Dooks1-1/+1
The rockchip_irq_gc_mask_set_bit() function is not exported our used outside of ppinctrl-rockchip.c so fix the following sparse error by making it static: drivers/pinctrl/pinctrl-rockchip.c:2010:6: warning: symbol 'rockchip_irq_gc_mask_set_bit' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-06-15pinctrl: fix incorrect inline keyword in multiple driversArnd Bergmann1-1/+1
When building with 'make W=1', we get harmless warnings about five drivers in drivers/pinctrl, which all contain a copy of the same line: drivers/pinctrl/freescale/pinctrl-imx1-core.c:160:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration] This replaces the somewhat nonstandard 'static const inline' with 'static inline const', which has the same meaning but does not cause this warning. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-05-11pinctrl: rockchip: fix pull setting error for rk3399David Wu1-52/+127
This patch fixes the pinctrl pull bias setting, since the pull up/down setting is the contrary for gpio0(just the gpio0a and gpio0b) and gpio2(just the gpio2c and gpio2d). From the TRM said, the gpio0a pull polarity setting: gpio0a_p GPIO0A PE/PS programmation section, every GPIO bit corresponding to 2bits[PS:PE] 2'b00: Z(Normal operation); 2'b11: weak 1(pull-up); 2'b01: weak 0(pull-down); 2'b10: Z(Normal operation); Then, the other gpios setting as the following: gpio1a_p (e.g.: gpio1, gpio2a, gpio2b, gpio3...) GPIO1A PU/PD programmation section, every GPIO bit corresponding to 2bits 2'b00: Z(Normal operation); 2'b01: weak 1(pull-up); 2'b10: weak 0(pull-down); 2'b11: Z(Normal operation); For example,(rk3399evb board) sdmmc_cd --->gpio0_a7 localhost / # io -r -4 0xff320040 ff320040: 00004d5f In general,the value should be 0x0000cd5f since the pin has been set in the dts. Signed-off-by: David Wu <david.wu@rock-chips.com> Signed-off-by: Caesar Wang <wxt@rock-chips.com> Cc: linux-gpio@vger.kernel.org Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-21pinctrl: rockchip: Use devm_pinctrl_register() for pinctrl registrationLaxman Dewangan1-1/+1
Use devm_pinctrl_register() for pin control registration. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: linux-rockchip@lists.infradead.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-13pinctrl: rockchip: add support the get_directionCaesar Wang1-0/+11
This patch adds the get_direction to support the gpio interface. The gpio direction is not used on rockchip platform when use the gpio debugfs. Tested on kylin board. (RK3036 SoCs) The repro steps: $/sys/class/gpio/ echo 53 > export $/sys/class/gpio/gpio53# cat direction in In general, the gpio53 should be out value, but the direction is the default value 'in', since the get_direction didn't supported in rockchip pinctrl. So, we should add this patch to support it. Cc: linux-gpio@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by: Caesar Wang <wxt@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10pinctrl: rockchip: add support for the rk3399David Wu1-14/+355
The pinctrl of rk3399 is much different from other's, especially the 3bits of drive strength. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-17Merge tag 'gpio-v4.5-1' of ↵Linus Torvalds1-11/+6
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "Here is the bulk of GPIO changes for v4.5. Notably there are big refactorings mostly by myself, aimed at getting the gpio_chip into a shape that makes me believe I can proceed to preserve state for a proper userspace ABI (character device) that has already been proposed once, but resulted in the feedback that I need to go back and restructure stuff. So I've been restructuring stuff. On the way I ran into brokenness (return code from the get_value() callback) and had to fix it. Also, refactored generic GPIO to be simpler. Some of that is still waiting to trickle down from the subsystems all over the kernel that provide random gpio_chips, I've touched every single GPIO driver in the kernel now, oh man I didn't know I was responsible for so much... Apart from that we're churning along as usual. I took some effort to test and retest so it should merge nicely and we shook out a couple of bugs in -next. Infrastructural changes: - In struct gpio_chip, rename the .dev node to .parent to better reflect the fact that this is not the GPIO struct device abstraction. We will add that soon so this would be totallt confusing. - It was noted that the driver .get_value() callbacks was sometimes reporting negative -ERR values to the gpiolib core, expecting them to be propagated to consumer gpiod_get_value() and gpio_get_value() calls. This was not happening, so as there was a mess of drivers returning negative errors and some returning "anything else than zero" to indicate that a line was active. As some would have bit 31 set to indicate "line active" it clashed with negative error codes. This is fixed by the largeish series clamping values in all drivers with !!value to [0,1] and then augmenting the code to propagate error codes to consumers. (Includes some ACKed patches in other subsystems.) - Add a void *data pointer to struct gpio_chip. The container_of() design pattern is indeed very nice, but we want to reform the struct gpio_chip to be a non-volative, stateless business, and keep states internal to the gpiolib to be able to hold on to the state when adding a proper userspace ABI (character device) further down the road. To achieve this, drivers need a handle at the internal state that is not dependent on their struct gpio_chip() so we add gpiochip_add_data() and gpiochip_get_data() following the pattern of many other subsystems. All the "use gpiochip data pointer" patches transforms drivers to this scheme. - The Generic GPIO chip header has been merged into the general <linux/gpio/driver.h> header, and the custom header for that removed. Instead of having a separate mm_gpio_chip struct for these generic drivers, merge that into struct gpio_chip, simplifying the code and removing the need for separate and confusing includes. Misc improvements: - Stabilize the way GPIOs are looked up from the ACPI legacy specification. - Incremental driver features for PXA, PCA953X, Lantiq (patches from the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48 New drivers: - Add a GPIO chip to the ALSA SoC AC97 driver. - Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but the branch is merged here too to account for infrastructural changes). - The sx150x driver now supports the sx1502" * tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits) gpio: generic: make bgpio_pdata always visible gpiolib: fix chip order in gpio list gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs() gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs() gpio: brcmstb: Allow building driver for BMIPS_GENERIC gpio: brcmstb: Set endian flags for big-endian MIPS gpio: moxart: fix build regression gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs() leds: pca9532: use gpiochip data pointer leds: tca6507: use gpiochip data pointer hid: cp2112: use gpiochip data pointer bcma: gpio: use gpiochip data pointer avr32: gpio: use gpiochip data pointer video: fbdev: via: use gpiochip data pointer gpio: pch: Optimize pch_gpio_get() Revert "pinctrl: lantiq: Implement gpio_chip.to_irq" pinctrl: nsp-gpio: use gpiochip data pointer pinctrl: vt8500-wmt: use gpiochip data pointer pinctrl: exynos5440: use gpiochip data pointer pinctrl: at91-pio4: use gpiochip data pointer ...
2016-01-05pinctrl: rockchip: use gpiochip data pointerLinus Walleij1-10/+5
This makes the driver use the data pointer added to the gpio_chip to store a pointer to the state container instead of relying on container_of(). Acked-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-22pinctrl: rockchip: add missing of_node_putJulia Lawall1-1/+4
for_each_child_of_node performs an of_node_get on each iteration, so a return from the loop requires an of_node_put. A simplified version of the semantic patch that fixes this problem is as follows (http://coccinelle.lip6.fr): // <smpl> @@ local idexpression n; expression e,e1; @@ for_each_child_of_node(e1,n) { ... ( of_node_put(n); | e = n | return n; | + of_node_put(n); ? return ...; ) ... } // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-11pinctrl: rockchip: add support for the rk3228Jeffy Chen1-0/+53
The pinctrl of rk3228 is much the same as rk3288's, but without pmu. Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19gpio: change member .dev to .parentLinus Walleij1-1/+1
The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-02Merge tag 'gpio-v4.4-1' of ↵Linus Torvalds1-12/+2
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "Here is the bulk of GPIO changes for the v4.4 development cycle. The only changes hitting outside drivers/gpio are in the pin control subsystem and these seem to have settled nicely in linux-next. Development mistakes and catfights are nicely documented in the reverts as you can see. The outcome of the ABI fight is that we're working on a chardev ABI for GPIO now, where hope to show results for the v4.5 kernel. Summary of changes: GPIO core: - Define and handle flags for open drain/open collector and open source/open emitter, also know as "single-ended" configurations. - Generic request/free operations that handle calling out to the (optional) pin control backend. - Some refactoring related to an ABI change that did not happen, yet provide useful. - Added a real-time compliance checklist. Many GPIO chips have irqchips, and need to think this over with the RT patches going upstream. - Restructure, fix and clean up Kconfig menus a bit. New drivers: - New driver for AMD Promony. - New driver for ACCES 104-IDIO-16, a port-mapped I/O card, ISA-style. Very retro. Subdriver changes: - OMAP changes to handle real time requirements. - Handle trigger types for edge and level IRQs on PL061 properly. As this hardware is very common it needs to set a proper example for others to follow. - Some container_of() cleanups. - Delete the unused MSM driver in favor of the driver that is embedded inside the pin control driver. - Cleanup of the ath79 GPIO driver used by many, many OpenWRT router targets. - A consolidated IT87xx driver replacing the earlier very specific IT8761e driver. - Handle the TI TCA9539 in the PCA953x driver. Also handle ACPI devices in this subdriver. - Drop xilinx arch dependencies as these FPGAs seem to profilate over a few different architectures. MIPS and ARM come to mind" * tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (57 commits) gpio: fix up SPI submenu gpio: drop surplus I2C dependencies gpio: drop surplus X86 dependencies gpio: dt-bindings: document the official use of "ngpios" gpio: MAINTAINERS: Add an entry for the ATH79 GPIO driver gpio / ACPI: Allow shared GPIO event to be read via operation region gpio: group port-mapped I/O drivers in a menu gpio: Add ACCES 104-IDIO-16 driver maintainer entry gpio: zynq: Document interrupt-controller DT binding gpio: xilinx: Drop architecture dependencies gpio: generic: Revert to old error handling in bgpio_map gpio: add a real time compliance notes Revert "gpio: add a real time compliance checklist" gpio: Add GPIO support for the ACCES 104-IDIO-16 gpio: driver for AMD Promontory gpio: xlp: Convert to use gpiolib irqchip helpers gpio: add a real time compliance checklist gpio/xilinx: enable for MIPS gpiolib: Add and use OF_GPIO_SINGLE_ENDED flag gpiolib: Split GPIO flags parsing and GPIO configuration ...
2015-10-16pinctrl: replace trivial implementations of gpio_chip request/freeJonas Gorski1-12/+2
Replace all trivial request/free callbacks that do nothing but call into pinctrl code with the generic versions. Signed-off-by: Jonas Gorski <jogo@openwrt.org> Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Eric Anholt <eric@anholt.net> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Andrew Bresticker <abrestic@chromium.org> Acked-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Matthias Brugger <matthias.bgg@gmail.com> Acked-by: Lee Jones <lee@kernel.org> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-09-25pinctrl: rockchip: add support for the rk3036Xing Zheng1-0/+17
Many parts of pinctrl rk3036 are similar to rk2928's. Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-09-16genirq: Remove irq argument from irq flow handlersThomas Gleixner1-1/+1
Most interrupt flow handlers do not use the irq argument. Those few which use it can retrieve the irq number from the irq descriptor. Remove the argument. Search and replace was done with coccinelle and some extra helper scripts around it. Thanks to Julia for her help! Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Jiang Liu <jiang.liu@linux.intel.com>
2015-08-13pinctrl: rockchip: only enable gpio clock when it settingLin Huang1-4/+51
gpio can keep state even the clock disable, for save power consumption, only enable gpio clock when it setting Signed-off-by: Lin Huang <hl@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-17pinctrl/rockchip: Prepare rockchip_irq_demux for irq argument removalThomas Gleixner1-2/+2
The irq argument of most interrupt flow handlers is unused or merily used instead of a local variable. The handlers which need the irq argument can retrieve the irq number from the irq descriptor. Search and update was done with coccinelle and the invaluable help of Julia Lawall. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org
2015-07-17pinctrl: Use irq_desc_get_xxx() to avoid redundant lookup of irq_descJiang Liu1-2/+2
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we already have a pointer to corresponding irq_desc. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-07-17pinctrl/rockchip: Use irq_set_handler_locked()Thomas Gleixner1-2/+2
Use irq_set_handler_locked() as it avoids a redundant lookup of the irq descriptor. Search and replacement was done with coccinelle. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org
2015-07-17pinctrl/rockchip: Consolidate chained IRQ handler install/removeThomas Gleixner1-2/+2
Chained irq handlers usually set up handler data as well. We now have a function to set both under irq_desc->lock. Replace the two calls with one. Search and conversion was done with coccinelle. Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-gpio@vger.kernel.org
2015-06-17pinctrl: rockchip: add support for the rk3368Heiko Stübner1-0/+91
The rk3368 is the first ARM64 soc from Rockchip, but seems to share most peripherals with the ARM32 soc, including the pinctrl functionality. The only notable difference is - as with every Rockchip soc - that the offsets in the General Register Files moved around and a split of the pmu section of the rk3288 into pmu and pmugrf (pmu general register files) sections. The pinctrl driver of course only needs the pmugrf registers for controlling the pin settings. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-06-17pinctrl: rockchip: generalize perpin driver-strength settingHeiko Stübner1-13/+23
The upcoming support for the RK3368 ARM64 SoC also supports perpin drive strength settings (at different register positions), so generalize the register and offset calculation to easily support this one too. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-19 16:06:19 +0000