summaryrefslogtreecommitdiffstats
path: root/drivers/pinctrl/intel
AgeCommit message (Collapse)AuthorFilesLines
2020-06-22pinctrl: intel: Allow drivers to define ACPI address space IDAndy Shevchenko1-0/+2
Individual drivers may install ACPI OpRegion handlers based on address space ID which differs from community to community. Add special field in the struct intel_community for that purpose. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-06-22pinctrl: intel: Allow drivers to define total amount of IRQs per communityAndy Shevchenko1-0/+2
Some of the pin control devices may not be capable to generate IRQ per each pin in the community. Allow individual drivers to define total amount of IRQs per community. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-06-22pinctrl: cherryview: Convert chv_writel() to use chv_padreg()Andy Shevchenko1-32/+16
chv_writel() is now solely used for cases where we write data to the PAD registers. In order to simplify callers, calculate register address inside chv_writel(). Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-06-22pinctrl: cherryview: Introduce helpers to IO with common registersAndy Shevchenko1-13/+26
Pin control device and effectively the single community in it has a set of common registers. It's good to have a helpers to IO on them. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-06-22pinctrl: cherryview: Introduce chv_readl() helperAndy Shevchenko1-35/+36
There are plenty of places where we call readl(chv_padreg(pctrl, offset, ...)); Replace them with newly introduced chv_readl() helper chv_readl(pctrl, offset, ...); Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-22pinctrl: intel: Move npins closer to pin_base in struct intel_communityAndy Shevchenko1-2/+3
It's common across the drivers to use the (pin_base, npins) pair to describe community characteristics. Thus, move them in the struct intel_community to be closer to each other. While at it, add a blank line to cut driver usable fields from what core reserves for itself. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-22pinctrl: intel: Update description in struct intel_communityAndy Shevchenko1-3/+3
It appears that most of the drivers, that are using struct intel_community, utilize gpps rather than gpp_size. Update comment accordingly. While here, correct the description of gpp_size, i.e. remove double space and drop redundant 'etc.' part. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-17pinctrl: cherryview: Add missing spinlock usage in chv_gpio_irq_handlerGrace Kao1-0/+4
According to Braswell NDA Specification Update (#557593), concurrent read accesses may result in returning 0xffffffff and write instructions may be dropped. We have an established format for the commit references, i.e. cdca06e4e859 ("pinctrl: baytrail: Add missing spinlock usage in byt_gpio_irq_handler") Fixes: 0bd50d719b00 ("pinctrl: cherryview: prevent concurrent access to GPIO controllers") Signed-off-by: Grace Kao <grace.kao@intel.com> Reported-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-04-16pinctrl: lynxpoint: Use platform_get_irq_optional() explicitlyAndy Shevchenko1-5/+5
There is no need to repeat functionality of platform_get_irq_optional() in the driver. Replace it with explicit call to the helper. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2020-04-15pinctrl: baytrail: Use platform_get_irq_optional() explicitlyAndy Shevchenko1-5/+4
There is no need to repeat functionality of platform_get_irq_optional() in the driver. Replace it with explicit call to the helper. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-14pinctrl: intel: Add Intel Jasper Lake pin controller supportAndy Shevchenko3-0/+353
This driver adds pinctrl/GPIO support for Intel Jasper Lake SoC. The GPIO controller is based on the next generation GPIO hardware but still compatible with the one supported by the Intel core pinctrl/GPIO driver. Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-14pinctrl: intel: Introduce new flag to force GPIO base to be 0Andy Shevchenko2-0/+5
In some cases not the first group would like to have GPIO base to be 0. It's not possible right now due to 0 has special meaning already. Thus, introduce a new flag to allow drivers to force GPIO base to be 0 on a certain group. It's assumed that it can be only one group per device with such flag enabled. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-14pinctrl: tigerlake: Use generic flag for special GPIO base treatmentAndy Shevchenko1-17/+15
Since we have a generic flag for special GPIO base treatment, use it in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-14pinctrl: icelake: Use generic flag for special GPIO base treatmentAndy Shevchenko1-16/+14
Since we have a generic flag for special GPIO base treatment, use it in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-14pinctrl: cannonlake: Use generic flag for special GPIO base treatmentAndy Shevchenko1-30/+28
Since we have a generic flag for special GPIO base treatment, use it in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-14pinctrl: intel: Introduce common flags for GPIO mapping schemeAndy Shevchenko2-8/+25
Few drivers are using the same flag to tell Intel pin control core how to interpret GPIO base. Provide a generic flags so all drivers can use. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-13pinctrl: cherryview: Use GENMASK() consistentlyAndy Shevchenko1-8/+8
Use GENMASK() macro for all definitions where it's appropriate. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-13pinctrl: cherryview: Re-use data structures from pinctrl-intel.h (part 2)Andy Shevchenko1-165/+97
We have some data structures duplicated across the drivers. Let's deduplicate them by using ones that being provided by pinctrl-intel.h. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-13pinctrl: baytrail: Enable pin configuration setting for GPIO chipAndy Shevchenko1-0/+1
It appears that pin configuration for GPIO chip hasn't been enabled yet due to absence of ->set_config() callback. Enable it here for Intel Baytrail. Fixes: c501d0b149de ("pinctrl: baytrail: Add pin control operations") Depends-on: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-04-13pinctrl: sunrisepoint: Fix PAD lock register offset for SPT-HAndy Shevchenko1-7/+8
It appears that SPT-H variant has different offset for PAD locking registers. Fix it here. Fixes: 551fa5801ef1 ("pinctrl: intel: sunrisepoint: Add Intel Sunrisepoint-H support") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-01-16pinctrl: tigerlake: Tiger Lake uses _HID enumerationMika Westerberg1-297/+250
Turns out that Tiger Lake GPIO will be enumerated using _HID method where there is only a single ACPI device and multiple BARs so rework the driver to support that scheme instead. Fixes: c9ccf71fc807 ("pinctrl: intel: Add Intel Tiger Lake pin controller support") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-16pinctrl: sunrisepoint: Add Coffee Lake-S ACPI IDMika Westerberg1-0/+1
Intel Coffee Lake-S PCH has the same GPIO hardware than Sunrisepoint-H PCH but the ACPI ID is different. Add this new ACPI ID to the list of supported devices. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-09pinctrl: intel: Pass irqchip when adding gpiochipLinus Walleij1-13/+13
We need to convert all old gpio irqchips to pass the irqchip setup along when adding the gpio_chip. For more info see drivers/gpio/TODO. For chained irqchips this is a pretty straight-forward conversion. Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-09pinctrl: intel: Add GPIO <-> pin mapping ranges via callbackLinus Walleij1-13/+22
When IRQ chip is instantiated via GPIO library flow, the few functions, in particular the ACPI event registration mechanism, on some of ACPI based platforms expect that the pin ranges are initialized to that point. Add GPIO <-> pin mapping ranges via callback in the GPIO library flow. Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-09pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq ↵Hans de Goede1-4/+4
pin to output Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI resource so we can do this without problems as long as we release the IRQ before changing the pin to output mode. On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, but this triggers the WARN in byt_gpio_set_direction-s output path because direct-irq support is enabled on the pin. This commit replaces the WARN call with a dev_info_once call, fixing a bunch of WARN splats in dmesg on each suspend/resume cycle. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-09pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pinsHans de Goede1-1/+7
Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, until the goodix driver gets rmmod-ed and then insmod-ed again. In this case byt_gpio_disable_free() calls byt_gpio_clear_triggering() which clears the IRQ flags and after that the (direct) IRQ no longer triggers. This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag to byt_gpio_clear_triggering(). Note that byt_gpio_clear_triggering() only gets called from byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded from the irq_valid mask by byt_init_irq_valid_mask(). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2020-01-08pinctrl: sunrisepoint: Add missing Interrupt Status register offsetBoyan Ding1-0/+1
Commit 179e5a6114cc ("pinctrl: intel: Remove default Interrupt Status offset") removes default interrupt status offset of GPIO controllers, with previous commits explicitly providing the previously default offsets. However, the is_offset value in SPTH_COMMUNITY is missing, preventing related irq from being properly detected and handled. Fixes: f702e0b93cdb ("pinctrl: sunrisepoint: Provide Interrupt Status register offset") Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745 Cc: stable@vger.kernel.org Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Update summary in the driverAndy Shevchenko1-4/+6
Reflect in the driver that it is now a pin control one. While here, update copyright years and authors. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Switch to pin control APIAndy Shevchenko2-57/+13
When all preparations are done, we may switch to pin control API. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Add GPIO <-> pin mapping ranges via callbackAndy Shevchenko1-0/+14
When IRQ chip is instantiated via GPIO library flow, the few functions, in particular the ACPI event registration mechanism, on some of ACPI based platforms expect that the pin ranges are initialized to that point. Add GPIO <-> pin mapping ranges via callback in the GPIO library flow. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Implement ->pin_dbg_show()Andy Shevchenko1-0/+23
The introduced callback ->pin_dbg_show() is useful for debugging. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Add pin control operationsAndy Shevchenko1-1/+314
Add implementation for: - pin control, group information retrieval: count, name and pins - pin muxing: - function information (count, name and groups) - mux setting - GPIO control (enable, disable, set direction) - pin configuration: - pull disable, up and down - any other option is treated as not supported. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Reuse struct intel_pinctrl in the driverAndy Shevchenko1-24/+60
We may use now available struct intel_pinctrl in the driver. No functional change implied. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Add pin control data structuresAndy Shevchenko1-2/+124
In order to implement pin control for Intel Lynxpoint, we need data structures in which to store and pass along pin, community and SoC data information. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Implement intel_gpio_get_direction callbackAndy Shevchenko1-0/+11
Allows querying GPIO direction from the pad config register. If the pad is not in GPIO mode, return an error. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Implement ->irq_ack() callbackAndy Shevchenko1-3/+14
Instead of playing tricks with registers in the interrupt handler, utilize the IRQ chip core for ACKing interrupts properly. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Move ownership check to IRQ chipAndy Shevchenko1-6/+6
There is nothing wrong with requesting pin that owned by ACPI. The only difference is how interrupt status will be reflected. It means that in ACPI mode we may not use pin as GPIO-backed IRQ. Taking above into consideration, move the check from GPIO to IRQ chip callback. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Move lp_irq_type() closer to IRQ related routinesAndy Shevchenko1-44/+44
Consolidate IRQ routines for better maintenance. While here, rename lp_irq_type() to lp_irq_set_type() to be in align with a callback name. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Move ->remove closer to ->probe()Andy Shevchenko1-6/+6
Consolidate ->remove and ->probe() callbacks for better maintenance. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Extract lp_gpio_acpi_use() for future useAndy Shevchenko1-2/+12
We may need this function for other features in the pin control driver. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Convert unsigned to unsigned intAndy Shevchenko1-12/+12
Simple type conversion with no functional change implied. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Switch to memory mapped IO accessorsAndy Shevchenko1-44/+44
Convert driver to use memory mapped IO accessors. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Keep pointer to struct device instead of its containerAndy Shevchenko1-7/+7
There is no need to keep pointer to struct platform_device, which is container of struct device, because the latter is what have been used everywhere outside of ->probe() path. In any case we may derive pointer to the container when needed. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Relax GPIO request rulesAndy Shevchenko1-3/+11
A pin in native mode still can be requested as GPIO, though we assume that firmware has configured it properly, which sometimes is not the case. Here we allow turning the pin as GPIO to avoid potential issues, but issue warning that something might be wrong. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Assume 2 bits for mode selectorAndy Shevchenko1-2/+4
New generations can use 2 bits for mode selector. Update the code to support it. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Use standard pattern for memory allocationAndy Shevchenko1-1/+1
The pattern foo = kmalloc(sizeof(*foo), GFP_KERNEL); has an advantage when foo type is changed. Since we are planning a such, better to be prepared by using standard pattern for memory allocation. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Use %pR to print IO resourceAndy Shevchenko1-2/+1
Replace explicit casting by pointer to struct resource with specifier replacement to %pR to print the IO resource. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Drop useless assignmentAndy Shevchenko1-1/+1
There is no need to assign ret variable in ->probe(). Drop useless assignment. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Correct amount of pinsAndy Shevchenko1-6/+6
When we count from 0 it's possible to get into off-by-one error. That's what had happened to this driver. So, correct amount of pins and related typos in the code. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2019-12-13pinctrl: lynxpoint: Use raw_spinlock for lockingAndy Shevchenko1-14/+14
The Intel Lynxpoint pinctrl driver implements irqchip callbacks which are called with desc->lock raw_spinlock held. In mainline this is fine because spinlock resolves to raw_spinlock. However, running the same code in -rt we will get a BUG() asserted. This is because in -rt spinlocks are preemptible so taking the driver private spinlock in irqchip callbacks causes might_sleep() to trigger. In order to keep -rt happy but at the same time make sure that register accesses get serialized, convert the driver to use raw_spinlock instead. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-13 14:55:34 +0000