summaryrefslogtreecommitdiffstats
path: root/drivers/phy
AgeCommit message (Collapse)AuthorFilesLines
2020-01-08phy: usb: Get all drivers that use USB clks using correct enable/disableAl Cooper1-14/+14
The BRCM USB Phy, ohci, ehci and xhci drivers all use the USB clocks but not all drivers use the clk_prepare_enable/clk_disable_unprepare versions to enable/disable the clocks. This change gets all drivers using the prepare version. Signed-off-by: Al Cooper <alcooperx@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: usb: EHCI DMA may lose a burst of DMA data for 7255xA0 familyAl Cooper1-0/+13
When the EHCI controller received a 512 byte USB packet that had to be broken into 2 256 byte bursts across the SCB bus AND there was a following 512 byte USB packet, the second burst of data from the first packet was sometimes being lost. If the burst size was changed to 128 bytes via the EBR_SCB_SIZE field in the USB_CTRL_EBRIDGE register we'd see the 4th 128 byte burst of the first packet being lost. This problem became much worse if other threads were running that accessed memory, like a memcpy test. Setting the EBR_SCB_SIZE to 512, which prevents breaking the EHCI USB packet (max size of 512 bytes) into bursts, fixed the problem. Signed-off-by: Al Cooper <alcooperx@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: qcom-qmp: Add SW reset registerVinod Koul1-0/+1
For V4 QMP UFS Phy, we need to assert reset bits, configure the phy and then deassert it, so add the QPHY_SW_RESET register which does this. Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Manu Gautam <mgautam@codeaurora.org> Reviewed-by: Can Guo <cang@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: qcom-qmp: remove no_pcs_sw_reset for sm8150Vinod Koul1-1/+0
SM8150 QMPY phy for UFS and onwards the PHY_SW_RESET is present in PHY's PCS register so we should not mark no_pcs_sw_reset for sm8150 and onwards Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Manu Gautam <mgautam@codeaurora.org> Reviewed-by: Can Guo <cang@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: qcom-qmp: remove duplicate powerdown writeVinod Koul1-1/+0
We already write to QPHY_POWER_DOWN_CONTROL in qcom_qmp_phy_com_init() before invoking qcom_qmp_phy_configure() so remove the duplicate write. Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: qcom-qmp: Use register definesVinod Koul1-2/+2
We already define register offsets so use them in register layout. Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Manu Gautam <mgautam@codeaurora.org> Reviewed-by: Can Guo <cang@codeaurora.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: brcm-sata: Implement 7216 initialization sequenceFlorian Fainelli1-0/+120
7216 is a 16nm process chip with a slightly different version of the PHY SerdDeS/AFE that requires a specific tuning sequence. Key on the compatible string to perform that initialization. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy/rockchip: inno-dsidphy: generalize parameter handlingHeiko Stuebner2-220/+100
During review it came to light that exposing the pll clock outside is not the right approach and struct phy_configure_opts_mipi_dphy exists just for that reason to transfer parameters to the phy. So drop the exposed clock and rely on the phy configure options to bring in the correct rate. That way we can also just drop the open coded timing struct and default values function. Fixes: b7535a3bc0ba ("phy/rockchip: Add support for Innosilicon MIPI/LVDS/TTL PHY") Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: lantiq: vrx200-pcie: Remove unneeded semicolonMa Feng1-1/+1
Fixes coccicheck warning: drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c:389:2-3: Unneeded semicolon Fixes: e52a632195bf ("phy: lantiq: vrx200-pcie: add a driver for the Lantiq VRX200 PCIe PHY") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Ma Feng <mafeng.ma@huawei.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: qualcomm: Adjust indentation in read_poll_timeoutNathan Chancellor1-1/+1
Clang warns: ../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:83:4: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50); ^ ../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:80:3: note: previous statement is here if (readl_relaxed(addr) & mask) ^ 1 warning generated. This warning occurs because there is a space after the tab on this line. Remove it so that the indentation is consistent with the Linux kernel coding style and clang no longer warns. Fixes: 1de990d8a169 ("phy: qcom: Add driver for QCOM APQ8064 SATA PHY") Link: https://github.com/ClangBuiltLinux/linux/issues/816 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-08phy: core: Add consumer device link supportAlexandre Torgue1-5/+44
In order to enforce suspend/resume ordering, this commit creates link between phy consumers and phy devices. This link avoids to suspend phy before phy consumers. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> [jonathanh@nvidia.com: Fix an abort when of_phy_get() returns error] Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-06phy: Enable compile testing for some of driversKrzysztof Kozlowski6-15/+22
Some of the phy drivers can be compile tested to increase build coverage. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20200103164710.4829-2-krzk@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-05net: switch to using PHY_INTERFACE_MODE_10GBASER rather than 10GKRRussell King1-10/+10
Switch network drivers, phy drivers, and SFP/phylink over to use the more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane ethernet, which is 10GBASE-R with autonegotiation on top, which our current usage on the affected platforms does not have. The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia PHY, which has a separate mode for 10GBASE-KR. For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R for compatibility with existing DT - this is the only network driver at present that makes use of PHY_INTERFACE_MODE_10GKR. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-31phy/rockchip: inno-hdmi: round clock rate down to closest 1000 HzJonas Karlman1-0/+4
Commit 287422a95fe2 ("drm/rockchip: Round up _before_ giving to the clock framework") changed what rate clk_round_rate() is called with, an additional 999 Hz added to the requsted mode clock. This has caused a regression on RK3328 and presumably also on RK3228 because the inno-hdmi-phy clock requires an exact match of the requested rate in the pre pll config table. When an exact match is not found the parent clock rate (24MHz) is returned to the clk_round_rate() caller. This cause wrong pixel clock to be used and result in no-signal when configuring a mode on RK3328. Fix this by rounding the rate down to closest 1000 Hz in round_rate func, this allows an exact match to be found in pre pll config table. Fixes: 287422a95fe2 ("drm/rockchip: Round up _before_ giving to the clock framework") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-26phy: cpcap-usb: Drop extra write to usb2 registerTony Lindgren1-6/+0
We are currently writing the same register twice. Let's enable the USB PHY only at the end of the function. Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-26phy: cpcap-usb: Improve host vs docked mode detectionTony Lindgren1-15/+58
When docked to a Motorola lapdock or media dock, we're in USB A-host mode with VBUS provided by the dock. When in regular USB A-host mode, we're providing the VBUS. And in regular USB A-host mode we must also keep kicking the VBUS to keep it active. Let's wait a bit before configuring the USB PHY to allow some time between the ID and VBUS changes. And let's add vbus_provider flag so we can detect docked mode and regularo USB A-host mode better. With better USB A-host mode detection, we can now also just kick the VBUS to keep it enabled and leave out the unnecessary line muxing. We only need to set and clear vbus_provider in the delayed work so no locking is needed for it currently. Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-26phy: cpcap-usb: Prevent USB line glitches from waking up modemTony Lindgren1-3/+15
The micro-USB connector on Motorola Mapphone devices can be muxed between the SoC and the mdm6600 modem. But even when used for the SoC, configuring the PHY with ID pin grounded will wake up the modem from idle state. Looks like the issue is probably caused by line glitches. We can prevent the glitches by using a previously unknown mode of the GPIO mux to prevent the USB lines from being connected to the moden while configuring the USB PHY, and enable the USB lines after configuring the PHY. Note that this only prevents waking up mdm6600 as regular USB A-host mode, and does not help when connected to a lapdock. The lapdock specific issue still needs to be debugged separately. Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-26phy: mapphone-mdm6600: Fix uninitialized status value regressionTony Lindgren1-8/+3
Only the used bits get cleared with bitmap_zero() when we call gpiod_get_array_value_cansleep(). We must mask only the bits we're using for ddata->status as the other bits in the bitmap may not be initialized. And let's also drop useless debug code accidentally left over while at it. Fixes: b9762bebc633 ("gpiolib: Pass bitmaps, not integer arrays, to get/set array") Cc: Jacopo Mondi <jacopo@jmondi.org> Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-26phy: cpcap-usb: Fix flakey host idling and enumerating of devicesTony Lindgren1-2/+2
We must let the USB host idle things properly before we switch to debug UART mode. Otherwise the USB host may never idle after disconnecting devices, and that causes the next enumeration to be flakey. Cc: Jacopo Mondi <jacopo@jmondi.org> Cc: Marcel Partap <mpartap@gmx.net> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Michael Scott <hashcode0f@gmail.com> Cc: NeKit <nekit1000@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Acked-by: Pavel Machek <pavel@ucw.cz> Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-20phy: qcom-qmp: Increase PHY ready timeoutBjorn Andersson1-1/+1
It's typical for the QHP PHY to take slightly above 1ms to initialize, so increase the timeout of the PHY ready check to 10ms - as already done in the downstream PCIe driver. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Tested-by: Evan Green <evgreen@chromium.org> Tested-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-20phy: ti-pipe3: make clk operations symmetric in probe and removeChuhong Yuan1-11/+7
The driver calls clk_prepare_enable in probe but the corresponding clk_disable_unprepare() is in ti_pipe3_disable_clocks(). Move clk_disable_unprepare() to remove to make them symmetric. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-20phy: qcom-qmp: Use the correct style for SPDX License IdentifierNishad Kamdar1-1/+1
This patch corrects the SPDX License Identifier style in header files related to PHY drivers for Qualcomm platforms. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used). Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-20phy: hisilicon: Fix Kconfig indentationKrzysztof Kozlowski1-8/+8
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-20phy: cpcap-usb: Fix error path when no host driver is loadedTony Lindgren1-15/+18
If musb_mailbox() returns an error, we must still continue to finish configuring the phy. Otherwise the phy state may end up only half initialized, and this can cause the debug serial console to stop working. And this will happen if the usb driver musb controller is not loaded. Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox(). Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support") Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-05Merge tag 'armsoc-drivers' of ↵Linus Torvalds3-0/+303
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Olof Johansson: "Various driver updates for platforms: - A larger set of work on Tegra 2/3 around memory controller and regulator features, some fuse cleanups, etc.. - MMP platform drivers, in particular for USB PHY, and other smaller additions. - Samsung Exynos 5422 driver for DMC (dynamic memory configuration), and ASV (adaptive voltage), allowing the platform to run at more optimal operating points. - Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas - Clock/reset control driver for TI/OMAP - Meson-A1 reset controller support - Qualcomm sdm845 and sda845 SoC IDs for socinfo" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits) firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT soc: fsl: add RCPM driver dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition memory: tegra: Consolidate registers definition into common header memory: tegra: Ensure timing control debug features are disabled memory: tegra: Introduce Tegra30 EMC driver memory: tegra: Do not handle error from wait_for_completion_timeout() memory: tegra: Increase handshake timeout on Tegra20 memory: tegra: Print a brief info message about EMC timings memory: tegra: Pre-configure debug register on Tegra20 memory: tegra: Include io.h instead of iopoll.h memory: tegra: Adapt for Tegra20 clock driver changes memory: tegra: Don't set EMC rate to maximum on probe for Tegra20 memory: tegra: Add gr2d and gr3d to DRM IOMMU group memory: tegra: Set DMA mask based on supported address bits soc: at91: Add Atmel SFR SN (Serial Number) support memory: atmel-ebi: switch to SPDX license identifiers memory: atmel-ebi: move NUM_CS definition inside EBI driver soc: mediatek: Refactor bus protection control soc: mediatek: Refactor sram control ...
2019-12-03Merge tag 'pci-v5.5-changes' of ↵Linus Torvalds1-9/+61
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Enumeration: - Warn if a host bridge has no NUMA info (Yunsheng Lin) - Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov) Resource management: - Fix boot-time Embedded Controller GPE storm caused by incorrect resource assignment after ACPI Bus Check Notification (Mika Westerberg) - Protect pci_reassign_bridge_resources() against concurrent addition/removal (Benjamin Herrenschmidt) - Fix bridge dma_ranges resource list cleanup (Rob Herring) - Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the MMIO and prefetchable MMIO window sizes of hotplug bridges independently (Nicholas Johnson) - Fix MMIO/MMIO_PREF window assignment that assigned more space than desired (Nicholas Johnson) - Only enforce bus numbers from bridge EA if the bridge has EA devices downstream (Subbaraya Sundeep) - Consolidate DT "dma-ranges" parsing and convert all host drivers to use shared parsing (Rob Herring) Error reporting: - Restore AER capability after resume (Mayurkumar Patel) - Add PoisonTLPBlocked AER counter (Rajat Jain) - Use for_each_set_bit() to simplify AER code (Andy Shevchenko) - Fix AER kernel-doc (Andy Shevchenko) - Add "pcie_ports=dpc-native" parameter to allow native use of DPC even if platform didn't grant control over AER (Olof Johansson) Hotplug: - Avoid returning prematurely from sysfs requests to enable or disable a PCIe hotplug slot (Lukas Wunner) - Don't disable interrupts twice when suspending hotplug ports (Mika Westerberg) - Fix deadlocks when PCIe ports are hot-removed while suspended (Mika Westerberg) Power management: - Remove unnecessary ASPM locking (Bjorn Helgaas) - Add support for disabling L1 PM Substates (Heiner Kallweit) - Allow re-enabling Clock PM after it has been disabled (Heiner Kallweit) - Add sysfs attributes for controlling ASPM link states (Heiner Kallweit) - Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl" sysfs files (Heiner Kallweit) - Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on USB 2.0 or 1.1 connect events (Kai-Heng Feng) - Move power state check out of pci_msi_supported() (Bjorn Helgaas) - Fix incorrect MSI-X masking on resume and revert related nvme quirk for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan) - Always return devices to D0 when thawing to fix hibernation with drivers like mlx4 that used legacy power management (previously we only did it for drivers with new power management ops) (Dexuan Cui) - Clear PCIe PME Status even for legacy power management (Bjorn Helgaas) - Fix PCI PM documentation errors (Bjorn Helgaas) - Use dev_printk() for more power management messages (Bjorn Helgaas) - Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas) - Convert xen-platform from legacy to generic power management (Bjorn Helgaas) - Removed unused .resume_early() and .suspend_late() legacy power management hooks (Bjorn Helgaas) - Rearrange power management code for clarity (Rafael J. Wysocki) - Decode power states more clearly ("4" or "D4" really refers to "D3cold") (Bjorn Helgaas) - Notice when reading PM Control register returns an error (~0) instead of interpreting it as being in D3hot (Bjorn Helgaas) - Add missing link delays required by the PCIe spec (Mika Westerberg) Virtualization: - Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn Helgaas) - Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code previously didn't recognize that) (Kuppuswamy Sathyanarayanan) - Allow VFs to use PASID (the PF PASID capability is shared by the VFs, but the code previously didn't recognize that) (Kuppuswamy Sathyanarayanan) - Disconnect PF and VF ATS enablement, since ATS in PFs and associated VFs can be enabled independently (Kuppuswamy Sathyanarayanan) - Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan) - Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas) - Consolidate ATS declarations in linux/pci-ats.h (Krzysztof Wilczynski) - Remove unused PRI and PASID stubs (Bjorn Helgaas) - Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID interfaces that are only used by built-in IOMMU drivers (Bjorn Helgaas) - Hide PRI and PASID state restoration functions used only inside the PCI core (Bjorn Helgaas) - Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski) - Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut) - Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George Cherian) - Fix the UPDCR register address in the Intel ACS quirk (Steffen Liebergeld) - Unify ACS quirk implementations (Bjorn Helgaas) Amlogic Meson host bridge driver: - Fix meson PERST# GPIO polarity problem (Remi Pommarel) - Add DT bindings for Amlogic Meson G12A (Neil Armstrong) - Fix meson clock names to match DT bindings (Neil Armstrong) - Add meson support for Amlogic G12A SoC with separate shared PHY (Neil Armstrong) - Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe combo PHY (Neil Armstrong) - Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong) - Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT (Neil Armstrong) Broadcom iProc host bridge driver: - Invalidate iProc PAXB address mapping before programming it (Abhishek Shah) - Fix iproc-msi and mvebu __iomem annotations (Ben Dooks) Cadence host bridge driver: - Refactor Cadence PCIe host controller to use as a library for both host and endpoint (Tom Joseph) Freescale Layerscape host bridge driver: - Add layerscape LS1028a support (Xiaowei Bao) Intel VMD host bridge driver: - Add VMD bus 224-255 restriction decode (Jon Derrick) - Add VMD 8086:9A0B device ID (Jon Derrick) - Remove Keith from VMD maintainer list (Keith Busch) Marvell ARMADA 3700 / Aardvark host bridge driver: - Use LTSSM state to build link training flag since Aardvark doesn't implement the Link Training bit (Remi Pommarel) - Delay before training Aardvark link in case PERST# was asserted before the driver probe (Remi Pommarel) - Fix Aardvark issues with Root Control reads and writes (Remi Pommarel) - Don't rely on jiffies in Aardvark config access path since interrupts may be disabled (Remi Pommarel) - Fix Aardvark big-endian support (Grzegorz Jaszczyk) Marvell ARMADA 370 / XP host bridge driver: - Make mvebu_pci_bridge_emul_ops static (Ben Dooks) Microsoft Hyper-V host bridge driver: - Add hibernation support for Hyper-V virtual PCI devices (Dexuan Cui) - Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan Cui) - Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui) Mobiveil host bridge driver: - Change mobiveil csr_read()/write() function names that conflict with riscv arch functions (Kefeng Wang) NVIDIA Tegra host bridge driver: - Fix Tegra CLKREQ dependency programming (Vidya Sagar) Renesas R-Car host bridge driver: - Remove unnecessary header include from rcar (Andrew Murray) - Tighten register index checking for rcar inbound range programming (Marek Vasut) - Fix rcar inbound range alignment calculation to improve packing of multiple entries (Marek Vasut) - Update rcar MACCTLR setting to match documentation (Yoshihiro Shimoda) - Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual (Yoshihiro Shimoda) - Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon Horman) Rockchip host bridge driver: - Make rockchip 0V9 and 1V8 power regulators non-optional (Robin Murphy) Socionext UniPhier host bridge driver: - Set uniphier to host (RC) mode always (Kunihiko Hayashi) Endpoint drivers: - Fix endpoint driver sign extension problem when shifting page number to phys_addr_t (Alan Mikhak) Misc: - Add NumaChip SPDX header (Krzysztof Wilczynski) - Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski) - Remove unused includes (Krzysztof Wilczynski) - Removed unused sysfs attribute groups (Ben Dooks) - Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas) - Add PCIe Link Control 2 register field definitions to replace magic numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas) - Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas) - Use pcie_capability_read_word() instead of pci_read_config_word() in AMDGPU and Radeon CIK/SI (Frederick Lawler) - Remove unused pci_irq_get_node() Greg Kroah-Hartman) - Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig (Palmer Dabbelt, Michal Simek) - Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe) - Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn Helgaas) - Fix bridge emulation big-endian support (Grzegorz Jaszczyk) - Fix dwc find_next_bit() usage (Niklas Cassel) - Fix pcitest.c fd leak (Hewenliang) - Fix typos and comments (Bjorn Helgaas) - Fix Kconfig whitespace errors (Krzysztof Kozlowski)" * tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits) PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist asm-generic: Make msi.h a mandatory include/asm header Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T" PCI/MSI: Fix incorrect MSI-X masking on resume PCI/MSI: Move power state check out of pci_msi_supported() PCI/MSI: Remove unused pci_irq_get_node() PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer PCI: hv: Change pci_protocol_version to per-hbus PCI: hv: Add hibernation support PCI: hv: Reorganize the code in preparation of hibernation MAINTAINERS: Remove Keith from VMD maintainer PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code PCI/ASPM: Add sysfs attributes for controlling ASPM link states PCI: Fix indentation drm/radeon: Prefer pcie_capability_read_word() drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions drm/radeon: Correct Transmit Margin masks drm/amdgpu: Prefer pcie_capability_read_word() PCI: uniphier: Set mode register to host mode drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions ...
2019-11-27Merge tag 'char-misc-5.5-rc1' of ↵Linus Torvalds24-38/+1506
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big set of char/misc and other driver patches for 5.5-rc1 Loads of different things in here, this feels like the catch-all of driver subsystems these days. Full details are in the shortlog, but nothing major overall, just lots of driver updates and additions. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits) char: Fix Kconfig indentation, continued habanalabs: add more protection of device during reset habanalabs: flush EQ workers in hard reset habanalabs: make the reset code more consistent habanalabs: expose reset counters via existing INFO IOCTL habanalabs: make code more concise habanalabs: use defines for F/W files habanalabs: remove prints on successful device initialization habanalabs: remove unnecessary checks habanalabs: invalidate MMU cache only once habanalabs: skip VA block list update in reset flow habanalabs: optimize MMU unmap habanalabs: prevent read/write from/to the device during hard reset habanalabs: split MMU properties to PCI/DRAM habanalabs: re-factor MMU masks and documentation habanalabs: type specific MMU cache invalidation habanalabs: re-factor memory module code habanalabs: export uapi defines to user-space habanalabs: don't print error when queues are full habanalabs: increase max jobs number to 512 ...
2019-11-27Merge tag 'usb-5.5-rc1' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB updates from Greg KH: "Here is the big set of USB patches for 5.5-rc1 Lots of little things in here: - typec updates and additions - usb-serial drivers cleanups and fixes - misc USB drivers cleanups and fixes - gadget drivers new features and controllers added - usual xhci additions - other minor changes All of these have been in linux-next with no reported issues" * tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits) usb: gadget: udc: gr_udc: create debugfs directory under usb root usb: gadget: atmel: create debugfs directory under usb root usb: musb: create debugfs directory under usb root usb: serial: Fix Kconfig indentation usb: misc: Fix Kconfig indentation usb: gadget: Fix Kconfig indentation usb: host: Fix Kconfig indentation usb: dwc3: Fix Kconfig indentation usb: gadget: configfs: Fix missing spin_lock_init() usb-storage: Disable UAS on JMicron SATA enclosure USB: documentation: flags on usb-storage versus UAS USB: uas: heed CAPACITY_HEURISTICS USB: uas: honor flag to avoid CAPACITY16 usb: host: xhci-tegra: Correct phy enable sequence usb-serial: cp201x: support Mark-10 digital force gauge usb: chipidea: imx: pinctrl for HSIC is optional usb: chipidea: imx: refine the error handling for hsic usb: chipidea: imx: change hsic power regulator as optional usb: chipidea: imx: check data->usbmisc_data against NULL before access usb: chipidea: core: change vbus-regulator as optional ...
2019-11-20phy: ti: phy-gmii-sel: dependency from ti cpsw-switchdev driverGrygorii Strashko1-2/+2
Add dependency from TI_CPSW_SWITCHDEV. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31phy: phy-rockchip-inno-usb2: add phy description for px30Heiko Stuebner1-0/+1
The px30 soc from Rockchip shares the same register description as the rk3328, so can re-use its definitions. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-31phy: qcom-usb-hs: Fix extcon double register after power cycleStephan Gerhold1-2/+5
Commit f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API") switched from extcon_register_notifier() to the resource-managed API, i.e. devm_extcon_register_notifier(). This is problematic in this case, because the extcon notifier is dynamically registered/unregistered whenever the PHY is powered on/off. The resource-managed API does not unregister the notifier until the driver is removed, so as soon as the PHY is power cycled, attempting to register the notifier again results in: double register detected WARNING: CPU: 1 PID: 182 at kernel/notifier.c:26 notifier_chain_register+0x74/0xa0 Call trace: ... extcon_register_notifier+0x74/0xb8 devm_extcon_register_notifier+0x54/0xb8 qcom_usb_hs_phy_power_on+0x1fc/0x208 ... ... and USB stops working after plugging the cable out and in another time. The easiest way to fix this is to make a partial revert of commit f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API") and avoid using the resource-managed API in this case. Fixes: f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-31phy: renesas: phy-rcar-gen2: Fix the array off by one warningBiju Das1-1/+4
Fix the below smatch warning by adding variable check rather than the hardcoded value. warn: array off by one? 'data->select_value[channel_num]' Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-31phy: lantiq: vrx200-pcie: fix error return code in ↵Wei Yongjun1-1/+2
ltq_vrx200_pcie_phy_power_on() Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: e52a632195bf ("phy: lantiq: vrx200-pcie: add a driver for the Lantiq VRX200 PCIe PHY") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-31phy/rockchip: Add support for Innosilicon MIPI/LVDS/TTL PHYWyon Bi3-0/+814
The Innosilicon Video Combo PHY not only supports MIPI DSI, but also LVDS and TTL functions with small die size and low pin count. Customers can choose according to their own applications. Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com> [removed TTL mode for now, as it required a hook back into the dsi host] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-31phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoCIcenowy Zheng3-0/+202
Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also controlled). Add a driver for it. The register operations in this driver is mainly extracted from the BSP USB3 driver. Signed-off-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-25phy: qcom-qmp: Add SM8150 QMP UFS PHY supportVinod Koul2-0/+216
SM8150 UFS PHY is v4 of QMP phy. Add support for V4 QMP phy register defines and support for SM8150 QMP UFS PHY. Signed-off-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-25phy: ti: gmii-sel: fix mac tx internal delay for rgmii-rxidGrygorii Strashko1-1/+1
Now phy-gmii-sel will disable MAC TX internal delay for PHY interface mode "rgmii-rxid" which is incorrect. Hence, fix it by enabling MAC TX internal delay in the case of "rgmii-rxid" mode. Fixes: 92b58b34741f ("phy: ti: introduce phy-gmii-sel driver") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-25phy: tegra: use regulator_bulk_set_supply_names()Bartosz Golaszewski1-3/+3
Use the new regulator helper instead of a for loop. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-25phy: ti: dm816x: remove set but not used variable 'phy_data'YueHaibing1-3/+0
Fixes gcc '-Wunused-but-set-variable' warning: drivers/phy/ti/phy-dm816x-usb.c:192:29: warning: variable phy_data set but not used [-Wunused-but-set-variable] It is never used, so can be removed. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: renesas: rcar-gen3-usb2: Fix sysfs interface of "role"Yoshihiro Shimoda1-2/+3
Since the role_store() uses strncmp(), it's possible to refer out-of-memory if the sysfs data size is smaller than strlen("host"). This patch fixes it by using sysfs_streq() instead of strncmp(). Reported-by: Pavel Machek <pavel@denx.de> Fixes: 9bb86777fb71 ("phy: rcar-gen3-usb2: add sysfs for usb role swap") Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Pavel Machek <pavel@denx.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: tegra: xusb: Add vbus override support on Tegra186Nagarjuna Kristam1-0/+23
Tegra XUSB device control driver needs to control vbus override during its operations, add API for the support. Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: tegra: xusb: Add vbus override support on Tegra210Nagarjuna Kristam3-0/+82
Tegra XUSB device control driver needs to control vbus override during its operations, add API for the support. Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: tegra: xusb: Add usb3 port fake support on Tegra210Nagarjuna Kristam3-0/+123
On Tegra210, usb2 only otg/peripheral ports dont work in device mode. They need an assosciated usb3 port to work in device mode. Identify an unused usb3 port and assign it as a fake USB3 port to USB2 only port whose mode is otg/peripheral. Based on work by BH Hsieh <bhsieh@nvidia.com>. Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: tegra: xusb: Add XUSB dual mode support on Tegra210Nagarjuna Kristam1-2/+18
Configure the port capabilities based on usb_dr_mode settings. Based on work by JC Kuo <jckuo@nvidia.com>. Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com> Reviewed-by: JC Kuo <jckuo@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: phy-brcm-usb-init: fix use of integer as pointerBen Dooks1-1/+1
The xhci_ec_base variable is a pointer, so don't compare it with an integer. Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: phy-brcm-usb-init: fix __iomem annotationsBen Dooks1-4/+4
The register address should have __iomem attributes so fix this to remove the following sparse warnings: drivers/phy/broadcom/phy-brcm-usb-init.c:459:30: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:459:30: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:459:30: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:459:30: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:461:30: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:461:30: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:461:30: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:461:30: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:465:30: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:465:30: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:465:30: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:465:30: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:469:30: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:469:30: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:469:30: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:469:30: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:478:30: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:478:30: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:478:30: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:478:30: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:480:30: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:480:30: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:480:30: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:480:30: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:485:30: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:485:30: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:485:30: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:485:30: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:494:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:494:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:494:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:494:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:495:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:495:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:495:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:495:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:498:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:498:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:498:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:498:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:501:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:501:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:501:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:501:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:613:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:613:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:613:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:613:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:640:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:640:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:640:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:640:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:710:64: warning: Using plain integer as NULL pointer drivers/phy/broadcom/phy-brcm-usb-init.c:712:32: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:712:32: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:712:32: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:712:32: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:713:29: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:713:29: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:713:29: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:713:29: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:717:29: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:717:29: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:717:29: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:717:29: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:720:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:720:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:720:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:720:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:721:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:721:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:721:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:721:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:794:29: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:794:29: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:794:29: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:794:29: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:813:29: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:813:29: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:813:29: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:813:29: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:829:37: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:829:37: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:829:37: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:829:37: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:843:37: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:843:37: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:843:37: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:843:37: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:847:37: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:847:37: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:847:37: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:847:37: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:878:9: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:878:9: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:878:9: expected void [noderef] <asn:2> *reg drivers/phy/broadcom/phy-brcm-usb-init.c:878:9: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:880:29: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:880:29: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:880:29: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:880:29: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:896:29: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:896:29: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:896:29: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:896:29: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:901:37: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:901:37: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:901:37: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:901:37: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:905:37: warning: cast removes address space '<asn:2>' of expression drivers/phy/broadcom/phy-brcm-usb-init.c:905:37: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:905:37: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:905:37: got void * drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> * drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces) drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: too many warnings Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: hisilicon: use devm_platform_ioremap_resource() to simplify codeYueHaibing2-6/+2
Use devm_platform_ioremap_resource() to simplify the code a bit. This is detected by coccinelle. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: renesas: rcar-gen3-usb2: Use platform_get_irq_optional() for optional irqGeert Uytterhoeven1-1/+1
As platform_get_irq() now prints an error when the interrupt does not exist, a scary warning may be printed for an optional interrupt: phy_rcar_gen3_usb2 ee0a0200.usb-phy: IRQ index 0 not found Fix this by calling platform_get_irq_optional() instead. Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy-mvebu-a3700-utmi: Use devm_platform_ioremap_resource() in ↵Markus Elfring1-8/+1
mvebu_a3700_utmi_phy_probe() Simplify this function implementation by using a known wrapper function. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-23phy: tegra: xusb: remove unused variableChunfeng Yun1-3/+0
The local variable @priv is set but not used, can be removed Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-02 14:55:00 +0000