| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove duplicate include file
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200818114721.55464-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
clk_div_table and wiz_regmap_config are not modified and can therefore
be made const to allow the compiler to put them in read-only memory.
Before:
text data bss dec hex filename
20265 7044 64 27373 6aed drivers/phy/ti/phy-j721e-wiz.o
After:
text data bss dec hex filename
20649 6660 64 27373 6aed drivers/phy/ti/phy-j721e-wiz.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200524095516.25227-3-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix to return negative error code from some error handling
cases instead of 0, as done elsewhere in this function.
Fixes: 091876cc355d ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200507054109.110849-1-weiyongjun1@huawei.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
For DisplayPort use we need to set WIZ_CONFIG_LANECTL register's
P_STANDARD_MODE bits to "mode 3". In the DisplayPort use also the
P_ENABLE bits of the same register are set to P_ENABLE instead of
P_ENABLE_FORCE, so that the DisplayPort driver can enable and disable
the lane as needed. The DisplayPort mode is selected according to
"cdns,phy-type"-properties found in link subnodes under the managed
serdes (see "ti,sierra-phy-t0" and "ti,j721e-serdes-10g" devicetree
bindings for details). All other values of "cdns,phy-type"-property
but PHY_TYPE_DP will set P_STANDARD_MODE bits to 0 and P_ENABLE bits
to force enable.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 091876cc355d ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Based on this GPIO state we need to configure LN10
bit to swap lane0 and lane1 if required (flipped connector).
Type-C companions typically need some time after the cable is
plugged before and before they reflect the correct status of
Type-C plug orientation on the DIR line.
Type-C Spec specifies CC attachment debounce time (tCCDebounce)
of 100 ms (min) to 200 ms (max).
Use the DT property to figure out if we need to add delay
or not before sampling the Type-C DIR line.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig), two divider clocks and supports
resets for each of the lanes.
[jsarha@ti.com: Add support for Torrent(10G) SERDES wrapper]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
