summaryrefslogtreecommitdiffstats
path: root/drivers/pcmcia
AgeCommit message (Collapse)AuthorFilesLines
2017-05-10Merge tag 'hwparam-20170420' of ↵Linus Torvalds2-8/+8
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs Pull hw lockdown support from David Howells: "Annotation of module parameters that configure hardware resources including ioports, iomem addresses, irq lines and dma channels. This allows a future patch to prohibit the use of such module parameters to prevent that hardware from being abused to gain access to the running kernel image as part of locking the kernel down under UEFI secure boot conditions. Annotations are made by changing: module_param(n, t, p) module_param_named(n, v, t, p) module_param_array(n, t, m, p) to: module_param_hw(n, t, hwtype, p) module_param_hw_named(n, v, t, hwtype, p) module_param_hw_array(n, t, hwtype, m, p) where the module parameter refers to a hardware setting hwtype specifies the type of the resource being configured. This can be one of: ioport Module parameter configures an I/O port iomem Module parameter configures an I/O mem address ioport_or_iomem Module parameter could be either (runtime set) irq Module parameter configures an I/O port dma Module parameter configures a DMA channel dma_addr Module parameter configures a DMA buffer address other Module parameter configures some other value Note that the hwtype is compile checked, but not currently stored (the lockdown code probably won't require it). It is, however, there for future use. A bonus is that the hwtype can also be used for grepping. The intention is for the kernel to ignore or reject attempts to set annotated module parameters if lockdown is enabled. This applies to options passed on the boot command line, passed to insmod/modprobe or direct twiddling in /sys/module/ parameter files. The module initialisation then needs to handle the parameter not being set, by (1) giving an error, (2) probing for a value or (3) using a reasonable default. What I can't do is just reject a module out of hand because it may take a hardware setting in the module parameters. Some important modules, some ipmi stuff for instance, both probe for hardware and allow hardware to be manually specified; if the driver is aborts with any error, you don't get any ipmi hardware. Further, trying to do this entirely in the module initialisation code doesn't protect against sysfs twiddling. [!] Note that in and of itself, this series of patches should have no effect on the the size of the kernel or code execution - that is left to a patch in the next series to effect. It does mark annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in an already existing field" * tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits) Annotate hardware config module parameters in sound/pci/ Annotate hardware config module parameters in sound/oss/ Annotate hardware config module parameters in sound/isa/ Annotate hardware config module parameters in sound/drivers/ Annotate hardware config module parameters in fs/pstore/ Annotate hardware config module parameters in drivers/watchdog/ Annotate hardware config module parameters in drivers/video/ Annotate hardware config module parameters in drivers/tty/ Annotate hardware config module parameters in drivers/staging/vme/ Annotate hardware config module parameters in drivers/staging/speakup/ Annotate hardware config module parameters in drivers/staging/media/ Annotate hardware config module parameters in drivers/scsi/ Annotate hardware config module parameters in drivers/pcmcia/ Annotate hardware config module parameters in drivers/pci/hotplug/ Annotate hardware config module parameters in drivers/parport/ Annotate hardware config module parameters in drivers/net/wireless/ Annotate hardware config module parameters in drivers/net/wan/ Annotate hardware config module parameters in drivers/net/irda/ Annotate hardware config module parameters in drivers/net/hamradio/ Annotate hardware config module parameters in drivers/net/ethernet/ ...
2017-04-20Annotate hardware config module parameters in drivers/pcmcia/David Howells2-8/+8
When the kernel is running in secure boot mode, we lock down the kernel to prevent userspace from modifying the running kernel image. Whilst this includes prohibiting access to things like /dev/mem, it must also prevent access by means of configuring driver modules in such a way as to cause a device to access or modify the kernel image. To this end, annotate module_param* statements that refer to hardware configuration and indicate for future reference what type of parameter they specify. The parameter parser in the core sees this information and can skip such parameters with an error message if the kernel is locked down. The module initialisation then runs as normal, but just sees whatever the default values for those parameters is. Note that we do still need to do the module initialisation because some drivers have viable defaults set in case parameters aren't specified and some drivers support automatic configuration (e.g. PNP or PCI) in addition to manually coded parameters. This patch annotates drivers in drivers/pcmcia/. Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> cc: linux-pcmcia@lists.infradead.org
2017-03-21drivers/pcmcia: NO_IRQ removal for electra_cf.cMichael Ellerman1-2/+2
We'd like to eventually remove NO_IRQ on powerpc, so remove usages of it from electra_cf.c which is a powerpc-only driver. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-12-12drivers/pcmcia/m32r_pcc.c: check return from add_pcc_socketSudip Mukherjee1-2/+8
If request_irq() fails it passes the error to the caller. The caller now checks it and jumps to the common error path on failure. Link: http://lkml.kernel.org/r/1474237304-897-3-git-send-email-sudipm.mukherjee@gmail.com Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-12drivers/pcmcia/m32r_pcc.c: use common error pathSudip Mukherjee1-7/+10
Use a common error path for the failure. Link: http://lkml.kernel.org/r/1474237304-897-2-git-send-email-sudipm.mukherjee@gmail.com Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-12drivers/pcmcia/m32r_pcc.c: check return from request_irqSudip Mukherjee1-4/+10
While building m32r allmodconfig we were getting warning: drivers/pcmcia/m32r_pcc.c:331:2: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result request_irq() can fail and we should always be checking the result from it. Check the result and return it to the caller. Link: http://lkml.kernel.org/r/1474237304-897-1-git-send-email-sudipm.mukherjee@gmail.com Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-11-11pcmcia: fix return value of soc_pcmcia_regulator_setArnd Bergmann1-1/+1
The newly introduced soc_pcmcia_regulator_set() function sometimes returns without setting its return code, as shown by this warning: drivers/pcmcia/soc_common.c: In function 'soc_pcmcia_regulator_set': drivers/pcmcia/soc_common.c:112:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized] This changes it to propagate the regulator_disable() result instead. Fixes: ac61b6001a63 ("pcmcia: soc_common: add support for Vcc and Vpp regulators") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-09-22pcmcia: soc_common: add driver-data pointerRussell King1-0/+1
Add a driver-data pointer so that low level drivers can add additional data to the soc_common pcmcia socket structure. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: add support for voltage sense GPIOsRussell King2-2/+8
Add support for the voltage sense GPIOs which are wired up on some platforms. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: constify pcmcia_low_level ops pointerRussell King2-2/+2
Constify the pcmcia_low_level operation pointer to soc_pcmcia_init_one() which has no need to modify it. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: switch to a per-socket cpufreq notifierRussell King2-54/+26
Switch to a per-socket cpufreq notifier rather than a global notifier. This allows each socket to be self-contained. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: add support for Vcc and Vpp regulatorsRussell King2-1/+47
Add support for handling supply regulators in the soc_common code. This allows us to separate out the board specifics for setting voltages from the PCMCIA code. We detect when setting a voltage fails, and report this fact - some platforms have fixed-voltage supplies (eg, for CF sockets at 3.3V) and we need to ignore attempts to configure for 5V, as per the existing board specific drivers. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: add CF socket state helperRussell King4-16/+16
Add a helper to get the voltage state of CF sockets, where the voltage sense pins are not wired up. Switch assabet and cerf to use this helper. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: restore previous socket state on errorRussell King1-4/+10
If an attempt to set a socket state returns an error, restore the previous socket state. If restoring the previous socket state fails, warn about this. This allows us to have simple error handling in the socket state configuration handlers - there is no need for every handler implementation to manually undo the updates, which can be complex when regulators are involved. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: add support for reset and bus enable GPIOsRussell King2-0/+19
Add support to soc_common for controlling reset and bus enable GPIOs from within the generic soc_common layer, rather than having individual drivers having to perform this themselves. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: request legacy detect GPIO with active lowRussell King1-5/+8
Request the legacy card detect signal with the active low property and remove our own negation of the detection value. This allows us to use the firmware-defined polarities rather than hard-coding it into the driver. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: ignore invalid interruptsRussell King1-4/+6
If gpiod_to_irq() returns an invalid interrupt, we should not try to use it as an interrupt number. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: switch to using gpio_descsRussell King2-11/+41
Switch to using the gpiod_* consumer API rather than the legacy API. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-22pcmcia: soc_common: use devm_gpio_request_one()Russell King1-8/+4
Use devm_gpio_request_one() to request the GPIOs so we can avoid manual clean up these gpio resources. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-12pcmcia: lubbock: fix sockets configurationRobert Jarzmik3-6/+7
On lubbock board, the probe of the driver crashes by dereferencing very early a platform_data structure which is not set, in pxa2xx_configure_sockets(). The stack fixed is : [ 0.244353] SA1111 Microprocessor Companion Chip: silicon revision 1, metal revision 1 [ 0.256321] sa1111 sa1111: Providing IRQ336-390 [ 0.340899] clocksource: Switched to clocksource oscr0 [ 0.472263] Unable to handle kernel NULL pointer dereference at virtual address 00000004 [ 0.480469] pgd = c0004000 [ 0.483432] [00000004] *pgd=00000000 [ 0.487105] Internal error: Oops: f5 [#1] ARM [ 0.491497] Modules linked in: [ 0.494650] CPU: 0 PID: 1 Comm: swapper Not tainted 4.8.0-rc3-00080-g1aaa68426f0c-dirty #2068 [ 0.503229] Hardware name: Intel DBPXA250 Development Platform (aka Lubbock) [ 0.510344] task: c3e42000 task.stack: c3e44000 [ 0.514984] PC is at pxa2xx_configure_sockets+0x4/0x24 (drivers/pcmcia/pxa2xx_base.c:227) [ 0.520193] LR is at pcmcia_lubbock_init+0x1c/0x38 [ 0.525079] pc : [<c0247c30>] lr : [<c02479b0>] psr: a0000053 [ 0.525079] sp : c3e45e70 ip : 100019ff fp : 00000000 [ 0.536651] r10: c0828900 r9 : c0434838 r8 : 00000000 [ 0.541953] r7 : c0820700 r6 : c0857b30 r5 : c3ec1400 r4 : c0820758 [ 0.548549] r3 : 00000000 r2 : 0000000c r1 : c3c09c40 r0 : c3ec1400 [ 0.555154] Flags: NzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none [ 0.562450] Control: 0000397f Table: a0004000 DAC: 00000053 [ 0.568257] Process swapper (pid: 1, stack limit = 0xc3e44190) [ 0.574154] Stack: (0xc3e45e70 to 0xc3e46000) [ 0.578610] 5e60: c4849800 00000000 c3ec1400 c024769c [ 0.586928] 5e80: 00000000 c3ec140c c3c0ee0c c3ec1400 c3ec1434 c020c410 c3ec1400 c3ec1434 [ 0.595244] 5ea0: c0820700 c080b408 c0828900 c020c5f8 00000000 c0820700 c020c578 c020ac5c [ 0.603560] 5ec0: c3e687cc c3e71e10 c0820700 00000000 c3c02de0 c020bae4 c03c62f7 c03c62f7 [ 0.611872] 5ee0: c3e68780 c0820700 c042e034 00000000 c043c440 c020cdec c080b408 00000005 [ 0.620188] 5f00: c042e034 c00096c0 c0034440 c01c730c 20000053 ffffffff 00000000 00000000 [ 0.628502] 5f20: 00000000 c3ffcb87 c3ffcb90 c00346ac c3e66ba0 c03f7914 00000092 00000005 [ 0.636811] 5f40: 00000005 c03f847c 00000091 c03f847c 00000000 00000005 c0434828 00000005 [ 0.645125] 5f60: c043482c 00000092 c043c440 c0828900 c0434838 c0418d2c 00000005 00000005 [ 0.653430] 5f80: 00000000 c041858c 00000000 c032e9f0 00000000 00000000 00000000 00000000 [ 0.661729] 5fa0: 00000000 c032e9f8 00000000 c000f0f0 00000000 00000000 00000000 00000000 [ 0.670020] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 0.678311] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 0.686673] (pxa2xx_configure_sockets) from pcmcia_lubbock_init (/drivers/pcmcia/sa1111_lubbock.c:161) [ 0.696026] (pcmcia_lubbock_init) from pcmcia_probe (/drivers/pcmcia/sa1111_generic.c:213) [ 0.704358] (pcmcia_probe) from driver_probe_device (/drivers/base/dd.c:378 /drivers/base/dd.c:499) [ 0.712848] (driver_probe_device) from __driver_attach (/./include/linux/device.h:983 /drivers/base/dd.c:733) [ 0.721414] (__driver_attach) from bus_for_each_dev (/drivers/base/bus.c:313) [ 0.729723] (bus_for_each_dev) from bus_add_driver (/drivers/base/bus.c:708) [ 0.738036] (bus_add_driver) from driver_register (/drivers/base/driver.c:169) [ 0.746185] (driver_register) from do_one_initcall (/init/main.c:778) [ 0.754561] (do_one_initcall) from kernel_init_freeable (/init/main.c:843 /init/main.c:851 /init/main.c:869 /init/main.c:1016) [ 0.763409] (kernel_init_freeable) from kernel_init (/init/main.c:944) [ 0.771660] (kernel_init) from ret_from_fork (/arch/arm/kernel/entry-common.S:119) [ 0.779347] Code: c03c6305 c03c631e c03c632e e5903048 (e993000c) All code ======== 0: c03c6305 eorsgt r6, ip, r5, lsl #6 4: c03c631e eorsgt r6, ip, lr, lsl r3 8: c03c632e eorsgt r6, ip, lr, lsr #6 c: e5903048 ldr r3, [r0, #72] ; 0x48 10:* e993000c ldmib r3, {r2, r3} <-- trapping instruction Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-12pcmcia: sa1111: fix propagation of lowlevel board init return codeRussell King5-69/+58
When testing Lubbock, it was noticed that the sa1111 pcmcia driver bound but was not functional due to no sockets being registered. This is because the return code from the lowlevel board initialisation was not being propagated out of the probe function. Fix this. Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-12pcmcia: soc_common: fix SS_STSCHG polarityRussell King1-1/+1
SS_STSCHG should be set for an IO card when the BVD1 signal is asserted low, not high. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-12pcmcia: sa11xx_base: add units to the timing informationRussell King1-3/+3
Add units to the timing information, so we know that the numbers are nanoseconds. The output changes from: I/O : 165 (172) attribute: 300 (316) common : 300 (316) to: I/O : 165ns (172ns) attribute: 300ns (316ns) common : 300ns (316ns) Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-12pcmcia: sa11xx_base: fix reporting of timing informationRussell King1-1/+1
Fix the reporting of the currently programmed timing information. These entries have been showing zero due to the clock rate being a factor of 1000 too big. With this change, we go from: I/O : 165 (0) attribute: 300 (0) common : 300 (0) to: I/O : 165 (172) attribute: 300 (316) common : 300 (316) Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-09-12pcmcia: ds: fix suspend/resumeRussell King1-5/+7
PCMCIA suspend/resume no longer works since the commit mentioned below, as the callbacks are no longer made. Convert the driver to the new dev_pm_ops, which restores the suspend/resume functionality. Tested on the arm arch Assabet platform. Fixes: aa8e54b559479 ("PM / sleep: Go direct_complete if driver has no callbacks") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2016-05-01powerpc/mm: Use a helper for finding pte bits mapping I/O areaAneesh Kumar K.V1-1/+1
Use a helper instead of open coding with constants. A later patch will drop the WIMG bits and use PowerISA 3.0 defines. Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2016-03-29pcmcia: db1xxx_ss: fix last irq_to_gpio userManuel Lauss1-2/+9
remove the usage of removed irq_to_gpio() function. On pre-DB1200 boards, pass the actual carddetect GPIO number instead of the IRQ, because we need the gpio to actually test card status (inserted or not) and can get the irq number with gpio_to_irq() instead. Tested on DB1300 and DB1500, this patch fixes PCMCIA on the DB1500, which used irq_to_gpio(). Fixes: 832f5dacfa0b ("MIPS: Remove all the uses of custom gpio.h") Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: linux-pcmcia@lists.infradead.org Cc: Linux-MIPS <linux-mips@linux-mips.org> Cc: stable@vger.kernel.org # v4.3+ Patchwork: https://patchwork.linux-mips.org/patch/12747/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-02-16gpio: Include linux/gpio.h instead of asm/gpio.hBjorn Helgaas2-2/+1
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected, linux/gpio.h includes asm/gpio.h. Therefore, code should include linux/gpio.h instead of including asm/gpio.h directly. Remove includes of asm/gpio.h, adding an include of linux/gpio.h when necessary. This is a follow-on to 7563bbf89d06 ("gpiolib/arches: Centralise bolierplate asm/gpio.h"). Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-05pcmcia: use kstrdup() in pcmcia_device_query()Geliang Tang1-3/+1
Use kstrdup instead of kmalloc and strncpy. Signed-off-by: Geliang Tang <geliangtang@163.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-03pcmcia: soc_common: remove skt_dev_info's clk pointerRussell King3-3/+0
We no longer need to store the clk pointer in struct skt_dev_info as we no longer need to remember the clk pointer for the cleanup paths. Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-09-03pcmcia: sa11xx_base.c: remove useless init/exit functionsRussell King1-10/+0
A library module is not required to have module init/exit functions. Get rid of these unnecessary functions. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-09-03pcmcia: sa1111: simplify clk handing in sa1111_pcmcia_add()Russell King1-6/+7
clk_get(dev, NULL) will always refer to the same clock, so it's pointless calling this multiple times for the same device. As we no longer have to worry about the cleanup (via use of devm_clk_get()) we can simplify sa1111_pcmcia_add() too. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-09-03pcmcia: sa1111: update socket driver to use devm_clk_get() APIRussell King1-2/+1
Update the pxa2xx socket driver to use the devm_clk_get() API so that the cleanup paths are simplified. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-09-03pcmcia: pxa2xx: convert memory allocation to devm_* APIRussell King1-5/+3
Convert the pxa2xx socket driver memory allocation to use devm_kzalloc() to simplify the cleanup path. Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-09-03pcmcia: pxa2xx: update socket driver to use devm_clk_get() APIRussell King1-6/+2
Update the pxa2xx socket driver to use the devm_clk_get() API so that the cleanup paths are simplified. Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-07-08pcmcia: sa11x0: convert memory allocation to devm_* APIRussell King2-3/+1
Convert the sa11x0 socket driver memory allocation to use devm_kzalloc() to simplify the cleanup path. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-07-08pcmcia: sa11x0: fix missing clk_put() in sa11x0 socket driversRussell King2-3/+1
Fix the lack of clk_put() in sa11xx_base.c's error cleanup paths by converting the driver to the devm_* API. Fixes: 86d88bfca475 ("ARM: 8247/2: pcmcia: sa1100: make use of device clock") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-07-02Merge tag 'module-implicit-v4.1-rc8' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux Pull implicit module.h fixes from Paul Gortmaker: "Fix up implicit <module.h> users that will break later. The files changed here are simply modular source files that are implicitly relying on <module.h> being present. We fix them up now, so that we can decouple some of the module related init code from the core init code in the future. The addition of the module.h include to several files here is also a no-op from a code generation point of view, else there would already be compile issues with these files today. There may be lots more implicit includes of <module.h> in tree, but these are the ones that extensive build test coverage has shown that must be fixed in order to avoid build breakage fallout for the pending module.h <---> init.h code relocation we desire to complete" * tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: frv: add module.h to mb93090-mb00/flash.c to avoid compile fail drivers/cpufreq: include <module.h> for modular exynos-cpufreq.c code drivers/staging: include <module.h> for modular android tegra_ion code crypto/asymmetric_keys: pkcs7_key_type needs module.h sh: mach-highlander/psw.c is tristate and should use module.h drivers/regulator: include <module.h> for modular max77802 code drivers/pcmcia: include <module.h> for modular xxs1500_ss code drivers/hsi: include <module.h> for modular omap_ssi code drivers/gpu: include <module.h> for modular rockchip code drivers/gpio: include <module.h> for modular crystalcove code drivers/clk: include <module.h> for clk-max77xxx modular code
2015-06-26Merge tag 'char-misc-4.2-rc1' of ↵Linus Torvalds1-4/+6
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here's the big char/misc driver pull request for 4.2-rc1. Lots of mei, extcon, coresight, uio, mic, and other driver updates in here. Full details in the shortlog. All of these have been in linux-next for some time with no reported problems" * tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits) mei: me: wait for power gating exit confirmation mei: reset flow control on the last client disconnection MAINTAINERS: mei: add mei_cl_bus.h to maintained file list misc: sram: sort and clean up included headers misc: sram: move reserved block logic out of probe function misc: sram: add private struct device and virt_base members misc: sram: report correct SRAM pool size misc: sram: bump error message level on unclean driver unbinding misc: sram: fix device node reference leak on error misc: sram: fix enabled clock leak on error path misc: mic: Fix reported static checker warning misc: mic: Fix randconfig build error by including errno.h uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config uio: pruss: Add CONFIG_HAS_IOMEM dependence uio: pruss: Include <linux/sizes.h> extcon: Redefine the unique id of supported external connectors without 'enum extcon' type char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration(). Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion parport: check exclusive access before register w1: use correct lock on error in w1_seq_show() ...
2015-06-26Merge tag 'armsoc-cleanup' of ↵Linus Torvalds2-12/+14
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanups from Kevin Hilman: "A relatively small setup of cleanups this time around, and similar to last time the bulk of it is removal of legacy board support: - OMAP: removal of legacy (non-DT) booting for several platforms - i.MX: remove some legacy board files" * tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits) ARM: fix EFM32 build breakage caused by cpu_resume_arm ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state ARM: v7 setup function should invalidate L1 cache mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c ARM: OMAP2+: Constify irq_domain_ops ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers ARM: at91: remove useless Makefile.boot ARM: at91: remove at91rm9200_sdramc.h ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h ARM: at91/pm: use the atmel-mc syscon defines pcmcia: at91_cf: Use syscon to configure the MC/smc ARM: at91: declare the at91rm9200 memory controller as a syscon mfd: syscon: Add Atmel MC (Memory Controller) registers definition ARM: at91: drop sam9_smc.c ata: at91: use syscon to configure the smc ARM: ux500: delete static resource defines ARM: ux500: rename ux500_map_io ARM: ux500: look up PRCMU resource from DT ARM: ux500: kill off L2CC static map ...
2015-06-16drivers/pcmcia: include <module.h> for modular xxs1500_ss codePaul Gortmaker1-0/+1
This file is built off of a tristate Kconfig option and also contains modular function calls so it should explicitly include module.h to avoid compile breakage during header shuffles done in the future. Cc: Wolfram Sang <wsa@the-dreams.de> Acked-by: Wolfram Sang <wsa@the-dreams.de> Cc: linux-pcmcia@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2015-06-16pcmcia: do not break rsrc_nonstatic when handling anonymous cardsDominik Brodowski2-21/+27
Patch 1c6c9b1d9d25 caused a regression for rsrc_nonstatic: It relies on pccard_validate_cis() to determine whether an iomem resource can be used for PCMCIA cards. This override, however, lead invalid iomem resources to be accepted -- and lead to a fake CIS being used instead of the original CIS. To fix this issue, move the override for anonymous cards to the one place where it is needed -- when adding a PCMCIA device. Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2015-06-14pcmcia: Fix resource leaks in yenta_probe() and _close()Takeshi Yoshimura1-12/+21
There are some resource leaks in yenta_probe() and _close(). I fixed the following issues with some code cleanups. Thanks to Dominik's suggestions. On the error path in yenta_probe(): - a requested irq is not released - yenta_free_resources() and pci_set_drvdata(dev, NULL) are not called In yenta_close(): - kfree(sock) is not called - sock->base is always set to non-NULL when yenta_close() is called, therefore the check in yenta_close() is not necessary. Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2015-06-13Disable write buffering on Toshiba ToPIC95Ryan Underwood1-0/+16
Disable write buffering on the Toshiba ToPIC95 if it is enabled by somebody (it is not supposed to be a power-on default according to the datasheet). On the ToPIC95, practically no 32-bit Cardbus card will work under heavy load without locking up the whole system if this is left enabled. I tried about a dozen. It does not affect 16-bit cards. This is similar to the O2 bugs in early controller revisions it seems. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961 Cc: <stable@vger.kernel.org> Signed-off-by: Ryan C. Underwood <nemesis@icequake.net> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2015-05-30pcmcia: Convert dev_printk to dev_<level>Joe Perches8-152/+124
Reduce object size a little by using dev_<level> calls instead of dev_printk(KERN_<LEVEL>. Other miscellanea: o Coalesce formats o Realign arguments o Use pr_cont instead of naked printk reorder test to use "%s\n" Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2015-05-30pcmcia/vrc4171: Remove typedefs for enums and structHimangi Saraogi1-15/+15
The Linux kernel coding style guidelines suggest not using typedefs for structure and enum types. This patch gets rid of the typedefs for vrc4171_slot_t, vrc4171_slotb_t and vrc4171_socket_t. Also, the names of the enums and the struct are changed to drop the _t, to make the name look less typedef-like. The following Coccinelle semantic patch detects the cases for struct type: @tn@ identifier i; type td; @@ -typedef struct i { ... } -td ; @@ type tn.td; identifier tn.i; @@ -td + struct i Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2015-05-30pcmcia: Remove typedef in structs and emumHimangi Saraogi1-17/+17
The Linux kernel coding style guidelines suggest not using typedefs for structure and enum types. This patch gets rid of the typedefs for cirrus_state_t, vg46x_state_t and pcic_id. Also, the names of the structs are changed to drop the _t, to make the name look less typedef-like. The following Coccinelle semantic patch detects the cases for struct type: @tn@ identifier i; type td; @@ -typedef struct i { ... } -td ; @@ type tn.td; identifier tn.i; @@ -td + struct i [linux@dominikbrodowski.net: fix patch to apply cleanly after e632cd94723e was applied first] Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2015-05-30pcmcia: Remove typedef tuple_flagsHimangi Saraogi1-6/+6
The Linux kernel coding style guidelines suggest not using typedefs for structure types. This patch gets rid of the typedef for tuple_flags. The following Coccinelle semantic patch makes the transformation. @tn@ identifier i; type td; @@ -typedef struct i { ... } -td ; @@ type tn.td; identifier tn.i; @@ -td + struct i Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2015-05-30drivers: pcmcia: electra_cf.c fix checkpatch error and warningsLaurent Navet1-5/+5
fix these checkpatch errors and warning: - ERROR: "foo * bar" should be "foo *bar" - WARNING: please, no space before tabs - WARNING: sizeof *cf should be sizeof(*cf) - WARNING: space prohibited between function name and open parenthesis '('i Signed-off-by: Laurent Navet <laurent.navet@gmail.com> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2015-05-30drivers: pcmcia: ds.c fix checkpatch errorsLaurent Navet1-8/+9
fix these checkpatch errors : - ERROR: spaces required around that '<' (ctx:VxW) - ERROR: "foo * bar" should be "foo *bar" - WARNING: please, no space before tabs Signed-off-by: Laurent Navet <laurent.navet@gmail.com> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>