summaryrefslogtreecommitdiffstats
path: root/drivers/parport
AgeCommit message (Collapse)AuthorFilesLines
2018-08-18Merge tag 'char-misc-4.19-rc1' of ↵Linus Torvalds2-3/+8
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the bit set of char/misc drivers for 4.19-rc1 There is a lot here, much more than normal, seems like everyone is writing new driver subsystems these days... Anyway, major things here are: - new FSI driver subsystem, yet-another-powerpc low-level hardware bus - gnss, finally an in-kernel GPS subsystem to try to tame all of the crazy out-of-tree drivers that have been floating around for years, combined with some really hacky userspace implementations. This is only for GNSS receivers, but you have to start somewhere, and this is great to see. Other than that, there are new slimbus drivers, new coresight drivers, new fpga drivers, and loads of DT bindings for all of these and existing drivers. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits) android: binder: Rate-limit debug and userspace triggered err msgs fsi: sbefifo: Bump max command length fsi: scom: Fix NULL dereference misc: mic: SCIF Fix scif_get_new_port() error handling misc: cxl: changed asterisk position genwqe: card_base: Use true and false for boolean values misc: eeprom: assignment outside the if statement uio: potential double frees if __uio_register_device() fails eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency misc: ti-st: Fix memory leak in the error path of probe() android: binder: Show extra_buffers_size in trace firmware: vpd: Fix section enabled flag on vpd_section_destroy platform: goldfish: Retire pdev_bus goldfish: Use dedicated macros instead of manual bit shifting goldfish: Add missing includes to goldfish.h mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux dt-bindings: mux: add adi,adgs1408 Drivers: hv: vmbus: Cleanup synic memory free path Drivers: hv: vmbus: Remove use of slow_virt_to_phys() Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind() ...
2018-07-15parport: ieee1284: mark expected switch fall-throughsGustavo A. R. Silva1-1/+2
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-15parport: sunbpp: fix error return codeJulia Lawall1-2/+6
Return an error code on failure. Change leading spaces to tab on the first if. Problem found using Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-07parport: parport_serial: Add WCH CH382L PCIe single parallel port supportColin Ian King1-0/+9
The WCH CH382L PCIe adapter has 1 parallel port but unlike the similar WCH CH328 adapter there are no serial ports connected to it. Enable this adapter with the addition of the appropriate PCIe IDs and board support config. PCIe device ID 1c00:3050: 02:00.0 Serial controller: Device 1c00:3050 (rev 10) (prog-if 05 [16850]) Subsystem: Device 1c00:3050 Flags: fast devsel, IRQ 16 I/O ports at 2000 [size=256] Memory at d0000000 (32-bit, prefetchable) [size=32K] I/O ports at 2100 [size=4] Expansion ROM at b0200000 [disabled] [size=32K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/32 Maskable+ 64bit+ Capabilities: [80] Express Legacy Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Kernel driver in use: parport_pc Kernel modules: parport_pc, parport_serial Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-15docs: Fix some broken referencesMauro Carvalho Chehab1-3/+3
As we move stuff around, some doc references are broken. Fix some of them via this script: ./scripts/documentation-file-ref-check --fix Manually checked if the produced result is valid, removing a few false-positives. Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Coly Li <colyli@suse.de> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by: Jonathan Corbet <corbet@lwn.net>
2018-04-04Merge tag 'char-misc-4.17-rc1' of ↵Linus Torvalds3-81/+53
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc updates from Greg KH: "Here is the big set of char/misc driver patches for 4.17-rc1. There are a lot of little things in here, nothing huge, but all important to the different hardware types involved: - thunderbolt driver updates - parport updates (people still care...) - nvmem driver updates - mei updates (as always) - hwtracing driver updates - hyperv driver updates - extcon driver updates - ... and a handful of even smaller driver subsystem and individual driver updates All of these have been in linux-next with no reported issues" * tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits) hwtracing: Add HW tracing support menu intel_th: Add ACPI glue layer intel_th: Allow forcing host mode through drvdata intel_th: Pick up irq number from resources intel_th: Don't touch switch routing in host mode intel_th: Use correct method of finding hub intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate stm class: Make dummy's master/channel ranges configurable stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate MAINTAINERS: Bestow upon myself the care for drivers/hwtracing hv: add SPDX license id to Kconfig hv: add SPDX license to trace Drivers: hv: vmbus: do not mark HV_PCIE as perf_device Drivers: hv: vmbus: respect what we get from hv_get_synint_state() /dev/mem: Avoid overwriting "err" in read_mem() eeprom: at24: use SPDX identifier instead of GPL boiler-plate eeprom: at24: simplify the i2c functionality checking eeprom: at24: fix a line break eeprom: at24: tweak newlines eeprom: at24: refactor at24_probe() ...
2018-04-04Merge tag 'tty-4.17-rc1' of ↵Linus Torvalds1-3/+0
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver updates from Greg KH: "Here is the big set of tty and serial driver patches for 4.17-rc1 Not all that big really, most are just small fixes and additions to existing drivers. There's a bunch of work on the imx serial driver recently for some reason, and a new embedded serial driver added as well. Full details are in the shortlog. All of these have been in the linux-next tree for a while with no reported issues" * tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits) serial: expose buf_overrun count through proc interface serial: mvebu-uart: fix tx lost characters tty: serial: msm_geni_serial: Fix return value check in qcom_geni_serial_probe() tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP 8250-men-mcb: add support for 16z025 and 16z057 powerpc: Mark the variable earlycon_acpi_spcr_enable maybe_unused serial: stm32: fix initialization of RS485 mode ARM: dts: STi: Remove "console=ttyASN" from bootargs for STi boards vt: change SGR 21 to follow the standards serdev: Fix typo in serdev_device_alloc ARM: dts: STi: Fix aliases property name for STi boards tty: st-asc: Update tty alias serial: stm32: add support for RS485 hardware control mode dt-bindings: serial: stm32: add RS485 optional properties selftests: add devpts selftests devpts: comment devpts_mntget() devpts: resolve devpts bind-mounts devpts: hoist out check for DEVPTS_SUPER_MAGIC serial: 8250: Add Nuvoton NPCM UART serial: mxs-auart: disable clks of Alphascale ASM9260 ...
2018-03-27parisc/parport_gsc: Use NULL to avoid sparse warningHelge Deller1-1/+1
Signed-off-by: Helge Deller <deller@gmx.de>
2018-03-14parport: Replace short License header by SPDX identifierAndy Shevchenko1-7/+1
No functional changes involved. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Sort headers alphabeticallyAndy Shevchenko1-5/+5
While here, remove init.h inclusion since we are not using it directly and module.h will do this for us. No functional changes intended. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Switch to use module_pci_driver() macroAndy Shevchenko1-15/+1
Eliminate some boilerplate code by using module_pci_driver() instead of init/exit, moving the salient bits from init into probe. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Convert printk(KERN_WARN) to dev_warn()Andy Shevchenko1-6/+5
dev_warn() will print device name with associated driver, no need to keep this open coded. While here, adjust indentation in the rest of dev_dbg() calls. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Don't shadow error codes in ->probe()Andy Shevchenko1-6/+6
When ->probe() calls helper functions return theirs error codes instead of shadowing them. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Convert to use managed functions pcim_* and devm_*Andy Shevchenko1-10/+5
This makes the error handling much more simpler than open-coding everything and in addition makes the probe function smaller an tidier. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: PCI core handles power state for usAndy Shevchenko1-28/+12
There is no need to repeat the work that is already done in the PCI driver core. The patch removes excerpts from suspend and resume callbacks. Note that there is no more calls performed to enable or disable a PCI device during suspend-resume cycle. Nowadays they seems to be superflous. Someone can read more in [1]. While here, convert calls to new driver API. [1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Add support for BrainBoxes PX272/PX306 MIO cardAndy Shevchenko1-0/+12
This adds support for BrainBoxes Multi I/O cards (4+1 serial + 1 parallel port): 02:00.0 0702: 135a:4100 (rev 02) Subsystem: 135a:0443 Flags: fast devsel, IRQ 18 Memory at f7d02000 (32-bit, non-prefetchable) [size=128] I/O ports at e000 [size=128] I/O ports at e080 [size=64] I/O ports at e0c0 [size=16] Memory at f7d01000 (32-bit, non-prefetchable) [size=128] Memory at f7d00000 (32-bit, non-prefetchable) [size=128] Capabilities: [50] MSI: Enable- Count=1/4 Maskable- 64bit+ Capabilities: [78] Power Management version 3 Capabilities: [80] Express Legacy Endpoint, MSI 01 Capabilities: [100] Virtual Channel Capabilities: [800] Advanced Error Reporting Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: ax88796: Delete an unnecessary variable initialisation in ↵Markus Elfring1-1/+1
parport_ax88796_probe() The local variable "pp" will eventually be set to an appropriate pointer a bit later. Thus omit the explicit initialisation at the beginning. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: ax88796: Improve a size determination in parport_ax88796_probe()Markus Elfring1-1/+1
Replace the specification of a data structure by a pointer dereference as the parameter for the operator "sizeof" to make the corresponding size determination a bit safer according to the Linux coding style convention. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: ax88796: Delete an error message for a failed memory allocation in ↵Markus Elfring1-3/+1
parport_ax88796_probe() Omit an extra message for a memory allocation failure in this function. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport_pc: Add support for WCH CH382L PCI-E single parallel port card.Alexander Gerasiov1-0/+4
WCH CH382L is a PCI-E adapter with 1 parallel port. It is similair to CH382 but serial ports are not soldered on board. Detected as Serial controller: Device 1c00:3050 (rev 10) (prog-if 05 [16850]) Signed-off-by: Alexander Gerasiov <gq@redlab-i.ru> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28serial, pci_ids: Move duplicate IDs to PCI IDs databaseAndy Shevchenko1-3/+0
PCI ID database is for IDs used across several drivers. Here is the case for SUNIX combo cards. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-16Merge tag 'char-misc-4.15-rc1' of ↵Linus Torvalds1-1/+1
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc updates from Greg KH: "Here is the big set of char/misc and other driver subsystem patches for 4.15-rc1. There are small changes all over here, hyperv driver updates, pcmcia driver updates, w1 driver updats, vme driver updates, nvmem driver updates, and lots of other little one-off driver updates as well. The shortlog has the full details. All of these have been in linux-next for quite a while with no reported issues" * tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits) VME: Return -EBUSY when DMA list in use w1: keep balance of mutex locks and refcnts MAINTAINERS: Update VME subsystem tree. nvmem: sunxi-sid: add support for A64/H5's SID controller nvmem: imx-ocotp: Update module description nvmem: imx-ocotp: Enable i.MX7D OTP write support nvmem: imx-ocotp: Add i.MX7D timing write clock setup support nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function nvmem: imx-ocotp: Add support for banked OTP addressing nvmem: imx-ocotp: Pass parameters via a struct nvmem: imx-ocotp: Restrict OTP write to IMX6 processors nvmem: uniphier: add UniPhier eFuse driver dt-bindings: nvmem: add description for UniPhier eFuse nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset nvmem: qfprom: fix different address space warnings of sparse nvmem: mtk-efuse: fix different address space warnings of sparse nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it thunderbolt: tb: fix use after free in tb_activate_pcie_devices MAINTAINERS: Add git tree for Thunderbolt development ...
2017-11-13Merge branch 'timers-core-for-linus' of ↵Linus Torvalds1-14/+7
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer updates from Thomas Gleixner: "Yet another big pile of changes: - More year 2038 work from Arnd slowly reaching the point where we need to think about the syscalls themself. - A new timer function which allows to conditionally (re)arm a timer only when it's either not running or the new expiry time is sooner than the armed expiry time. This allows to use a single timer for multiple timeout requirements w/o caring about the first expiry time at the call site. - A new NMI safe accessor to clock real time for the printk timestamp work. Can be used by tracing, perf as well if required. - A large number of timer setup conversions from Kees which got collected here because either maintainers requested so or they simply got ignored. As Kees pointed out already there are a few trivial merge conflicts and some redundant commits which was unavoidable due to the size of this conversion effort. - Avoid a redundant iteration in the timer wheel softirq processing. - Provide a mechanism to treat RTC implementations depending on their hardware properties, i.e. don't inflict the write at the 0.5 seconds boundary which originates from the PC CMOS RTC to all RTCs. No functional change as drivers need to be updated separately. - The usual small updates to core code clocksource drivers. Nothing really exciting" * 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits) timers: Add a function to start/reduce a timer pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday() timer: Prepare to change all DEFINE_TIMER() callbacks netfilter: ipvs: Convert timers to use timer_setup() scsi: qla2xxx: Convert timers to use timer_setup() block/aoe: discover_timer: Convert timers to use timer_setup() ide: Convert timers to use timer_setup() drbd: Convert timers to use timer_setup() mailbox: Convert timers to use timer_setup() crypto: Convert timers to use timer_setup() drivers/pcmcia: omap1: Fix error in automated timer conversion ARM: footbridge: Fix typo in timer conversion drivers/sgi-xp: Convert timers to use timer_setup() drivers/pcmcia: Convert timers to use timer_setup() drivers/memstick: Convert timers to use timer_setup() drivers/macintosh: Convert timers to use timer_setup() hwrng/xgene-rng: Convert timers to use timer_setup() auxdisplay: Convert timers to use timer_setup() sparc/led: Convert timers to use timer_setup() mips: ip22/32: Convert timers to use timer_setup() ...
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman5-0/+5
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-20parport: make parport_ip32_ops const and __initconstBhumika Goyal1-1/+1
Make this const as it is only used during a copy operation. This usage is inside init function and the structure is not referenced after initialisation, so make it __initconst too. Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-05timer: Remove init_timer_on_stack() in favor of timer_setup_on_stack()Kees Cook1-14/+7
Remove uses of init_timer_on_stack() with open-coded function and data assignments that could be expressed using timer_setup_on_stack(). Several were removed from the stack entirely since there was a one-to-one mapping of parent structure to timer, those are switched to using timer_setup() instead. All related callbacks were adjusted to use from_timer(). Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Cc: Petr Mladek <pmladek@suse.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Sebastian Reichel <sre@kernel.org> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: linux1394-devel@lists.sourceforge.net Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: linux-s390@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com> Cc: linux-scsi@vger.kernel.org Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Ursula Braun <ubraun@linux.vnet.ibm.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Harish Patil <harish.patil@cavium.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Michael Reed <mdr@sgi.com> Cc: Manish Chopra <manish.chopra@cavium.com> Cc: Len Brown <len.brown@intel.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: linux-pm@vger.kernel.org Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: Tejun Heo <tj@kernel.org> Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Mark Gross <mark.gross@intel.com> Cc: linux-watchdog@vger.kernel.org Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: Guenter Roeck <linux@roeck-us.net> Cc: netdev@vger.kernel.org Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lkml.kernel.org/r/1507159627-127660-4-git-send-email-keescook@chromium.org
2017-09-05Merge tag 'char-misc-4.14-rc1' of ↵Linus Torvalds6-20/+18
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big char/misc driver update for 4.14-rc1. Lots of different stuff in here, it's been an active development cycle for some reason. Highlights are: - updated binder driver, this brings binder up to date with what shipped in the Android O release, plus some more changes that happened since then that are in the Android development trees. - coresight updates and fixes - mux driver file renames to be a bit "nicer" - intel_th driver updates - normal set of hyper-v updates and changes - small fpga subsystem and driver updates - lots of const code changes all over the driver trees - extcon driver updates - fmc driver subsystem upadates - w1 subsystem minor reworks and new features and drivers added - spmi driver updates Plus a smattering of other minor driver updates and fixes. All of these have been in linux-next with no reported issues for a while" * tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (244 commits) ANDROID: binder: don't queue async transactions to thread. ANDROID: binder: don't enqueue death notifications to thread todo. ANDROID: binder: Don't BUG_ON(!spin_is_locked()). ANDROID: binder: Add BINDER_GET_NODE_DEBUG_INFO ioctl ANDROID: binder: push new transactions to waiting threads. ANDROID: binder: remove proc waitqueue android: binder: Add page usage in binder stats android: binder: fixup crash introduced by moving buffer hdr drivers: w1: add hwmon temp support for w1_therm drivers: w1: refactor w1_slave_show to make the temp reading functionality separate drivers: w1: add hwmon support structures eeprom: idt_89hpesx: Support both ACPI and OF probing mcb: Fix an error handling path in 'chameleon_parse_cells()' MCB: add support for SC31 to mcb-lpc mux: make device_type const char: virtio: constify attribute_group structures. Documentation/ABI: document the nvmem sysfs files lkdtm: fix spelling mistake: "incremeted" -> "incremented" perf: cs-etm: Fix ETMv4 CONFIGR entry in perf.data file nvmem: include linux/err.h from header ...
2017-08-28parport: use release_mem_region instead of release_resourceAnton Vasilyev1-4/+2
Use api pair of request_mem_region and release_mem_region instead of release_resource. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28parport: cleanup statics initialization to NULL or 0Carlos Palminha4-4/+4
based on checkpatch, cleanup the "do not initialise statics to" 0 or NULL. Signed-off-by: Carlos Palminha <palminha@synopsys.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28parport_pc: use pr_contMikulas Patocka1-12/+12
The kernel adds newline automatically between printk calls, we must use pr_cont if we want multiple printk strings on the same line. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-22parisc/parport_gsc: Fix section mismatchesHelge Deller1-5/+5
Signed-off-by: Helge Deller <deller@gmx.de>
2017-04-20Annotate hardware config module parameters in drivers/parport/David Howells1-4/+4
When the kernel is running in secure boot mode, we lock down the kernel to prevent userspace from modifying the running kernel image. Whilst this includes prohibiting access to things like /dev/mem, it must also prevent access by means of configuring driver modules in such a way as to cause a device to access or modify the kernel image. To this end, annotate module_param* statements that refer to hardware configuration and indicate for future reference what type of parameter they specify. The parameter parser in the core sees this information and can skip such parameters with an error message if the kernel is locked down. The module initialisation then runs as normal, but just sees whatever the default values for those parameters is. Note that we do still need to do the module initialisation because some drivers have viable defaults set in case parameters aren't specified and some drivers support automatic configuration (e.g. PNP or PCI) in addition to manually coded parameters. This patch annotates drivers in drivers/parport/. Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
2017-03-16parport: fix attempt to write duplicate procfilesSudip Mukherjee1-2/+4
Usually every parallel port will have a single pardev registered with it. But ppdev driver is an exception. This userspace parallel port driver allows to create multiple parrallel port devices for a single parallel port. And as a result we were having a nice warning like: "sysctl table check failed: /dev/parport/parport0/devices/ppdev0/timeslice Sysctl already exists" Use the same logic as used in parport_register_device() and register the proc files only once for each parallel port. Fixes: 6fa45a226897 ("parport: add device-model to parport subsystem") Cc: stable <stable@vger.kernel.org> # v4.4+ Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656 Bugzilla: https://bugs.archlinux.org/task/52322 Tested-by: James Feeney <james@nurealm.net> Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-02sched/headers: Prepare to move signal wakeup & sigpending methods from ↵Ingo Molnar6-6/+6
<linux/sched.h> into <linux/sched/signal.h> Fix up affected files that include this signal functionality via sched.h. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-02-27lib/vsprintf.c: remove %Z supportAlexey Dobriyan1-1/+1
Now that %z is standartised in C99 there is no reason to support %Z. Unlike %L it doesn't even make format strings smaller. Use BUILD_BUG_ON in a couple ATM drivers. In case anyone didn't notice lib/vsprintf.o is about half of SLUB which is in my opinion is quite an achievement. Hopefully this patch inspires someone else to trim vsprintf.c more. Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2 Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-02-27scripts/spelling.txt: add "overwriten" pattern and fix typo instancesMasahiro Yamada1-1/+1
Fix typos and add the following to the scripts/spelling.txt: overwrien||overwritten Link: http://lkml.kernel.org/r/1481573103-11329-30-git-send-email-yamada.masahiro@socionext.com Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-01-28parisc, parport_gsc: Fixes for printk continuation linesHelge Deller1-4/+4
Signed-off-by: Helge Deller <deller@gmx.de>
2016-12-24Replace <asm/uaccess.h> with <linux/uaccess.h> globallyLinus Torvalds5-5/+5
This was entirely automated, using the script by Al: PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>' sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \ $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h) to do the replacement at the end of the merge window. Requested-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-04-30parport: use subsys_initcallSudip Mukherjee1-1/+1
The drivers which depends on parport may sometimes try to iniitialize and register with parport bus even before parport has actually registered with the device layer. The simplest solution is to mark the init function as subsys_initcall() and load the parport before the other drivers loads. Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: avoid assignment in ifSudip Mukherjee1-1/+2
It is not an usual practise to assign some value to a variable in the if test condition. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: remove unneeded spaceSudip Mukherjee1-47/+47
checkpatch complains that space is prohibited between function name and open parenthesis '('. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: change style of NULL comparisonSudip Mukherjee1-4/+4
checkpatch was complaining about NULL comparisons. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: remove unnecessary out of memory messageSudip Mukherjee1-10/+3
If kmalloc() or kzalloc() fails we will get sufficient messages in the logs, no need to print these extra messages. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: remove bracesSudip Mukherjee1-4/+2
checkpatch was complaining about braces for single statement block. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: quoted strings should not be splitSudip Mukherjee1-10/+8
user visible strings should not be split as that affects the ability to grep. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: code indent should use tabsSudip Mukherjee1-1/+1
Code should be indented using tabs and not by space. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: fix coding styleSudip Mukherjee1-25/+44
The multi-line comments were not according to the kernel coding style. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: EXPORT_SYMBOL should follow functionSudip Mukherjee1-16/+13
All symbols were exported at the end of the file but they are supposed to be exported just after the function. And checkpatch was complaining about it. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: remove trailing white spaceSudip Mukherjee1-4/+4
Trailing white space is not accepted in kernel coding style. Remove them. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-03parport: fix a trivial typoGeliang Tang1-1/+1
s/regsiter/register/ Signed-off-by: Geliang Tang <geliangtang@163.com> Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>