summaryrefslogtreecommitdiffstats
path: root/drivers/parport
AgeCommit message (Collapse)AuthorFilesLines
2019-11-13parport: daisy: use new parport device modelSudip Mukherjee1-1/+39
Modify parport daisy driver to use the new parallel port device model. Last attempt was '1aec4211204d ("parport: daisy: use new parport device model")' which failed as daisy was also trying to load the low level driver and that resulted in a deadlock. Cc: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Link: https://lore.kernel.org/r/20191016144540.18810-4-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13parport: load lowlevel driver if ports not foundSudip Mukherjee1-0/+21
Usually all the distro will load the parport low level driver as part of their initialization. But we can get into a situation where all the parallel port drivers are built as module and we unload all the modules at a later time. Then if we just do "modprobe parport" it will only load the parport module and will not load the low level driver which will actually register the ports. So, check the bus if there is any parport registered, if not, load the low level driver. We can get into the above situation with all distro but only Suse has setup the alias for "parport_lowlevel" and so it only works in Suse. Users of Debian based distro will need to load the lowlevel module manually. Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20191016144540.18810-3-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13parport: do not check portlist when using device-modelSudip Mukherjee1-3/+2
We do not need to maintain a list of ports when we are using the device-model. The base layer is going to maintain the list for us and we can get the list of ports just using bus_for_each_dev(). Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20191016144540.18810-2-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-13parport: daisy: avoid hardcoded nameSudip Mukherjee1-1/+1
The daisy device name is hardcoded, define it in the header file and use it in the code. Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20191016144540.18810-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-18Merge tag 'char-misc-5.4-rc1' of ↵Linus Torvalds2-5/+3
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big char/misc driver pull request for 5.4-rc1. As has been happening in previous releases, more and more individual driver subsystem trees are ending up in here. Now if that is good or bad I can't tell, but hopefully it makes your life easier as it's more of an aggregation of trees together to one merge point for you. Anyway, lots of stuff in here: - habanalabs driver updates - thunderbolt driver updates - misc driver updates - coresight and intel_th hwtracing driver updates - fpga driver updates - extcon driver updates - some dma driver updates - char driver updates - android binder driver updates - nvmem driver updates - phy driver updates - parport driver fixes - pcmcia driver fix - uio driver updates - w1 driver updates - configfs fixes - other assorted driver updates All of these have been in linux-next for a long time with no reported issues" * tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (200 commits) misc: mic: Use PTR_ERR_OR_ZERO rather than its implementation habanalabs: correctly cast variable to __le32 habanalabs: show correct id in error print habanalabs: stop using the acronym KMD habanalabs: display card name as sensors header habanalabs: add uapi to retrieve aggregate H/W events habanalabs: add uapi to retrieve device utilization habanalabs: Make the Coresight timestamp perpetual habanalabs: explicitly set the queue-id enumerated numbers habanalabs: print to kernel log when reset is finished habanalabs: replace __le32_to_cpu with le32_to_cpu habanalabs: replace __cpu_to_le32/64 with cpu_to_le32/64 habanalabs: Handle HW_IP_INFO if device disabled or in reset habanalabs: Expose devices after initialization is done habanalabs: improve security in Debug IOCTL habanalabs: use default structure for user input in Debug IOCTL habanalabs: Add descriptive name to PSOC app status register habanalabs: Add descriptive names to PSOC scratch-pad registers habanalabs: create two char devices per ASIC habanalabs: change device_setup_cdev() to be more generic ...
2019-09-04parport: parport_serial: Add support for Sunix Multi I/O boardsKai-Heng Feng1-12/+32
Sunix Multi I/O boards are different to Timedia's. This patch adds proper support for Sunix MIO boards with 1 parallel and up to 4 serial ports. Cc: Morris Ku <morris_ku@sunix.com> Cc: Debbie Liu <debbie_liu@sunix.com> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Link: https://lore.kernel.org/r/20190809190130.30773-2-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-05parport: parport_serial: Use dev_get_drvdataChuhong Yuan1-4/+2
Instead of using to_pci_dev + pci_get_drvdata, use dev_get_drvdata to make code simpler. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20190801191408.10977-3-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-05parport: Add missing newline at end of fileGeert Uytterhoeven1-1/+1
"git diff" says: \ No newline at end of file after modifying the file. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20190801191408.10977-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-09Merge tag 'docs-5.3' of git://git.lwn.net/linuxLinus Torvalds1-1/+1
Pull Documentation updates from Jonathan Corbet: "It's been a relatively busy cycle for docs: - A fair pile of RST conversions, many from Mauro. These create more than the usual number of simple but annoying merge conflicts with other trees, unfortunately. He has a lot more of these waiting on the wings that, I think, will go to you directly later on. - A new document on how to use merges and rebases in kernel repos, and one on Spectre vulnerabilities. - Various improvements to the build system, including automatic markup of function() references because some people, for reasons I will never understand, were of the opinion that :c:func:``function()`` is unattractive and not fun to type. - We now recommend using sphinx 1.7, but still support back to 1.4. - Lots of smaller improvements, warning fixes, typo fixes, etc" * tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits) docs: automarkup.py: ignore exceptions when seeking for xrefs docs: Move binderfs to admin-guide Disable Sphinx SmartyPants in HTML output doc: RCU callback locks need only _bh, not necessarily _irq docs: format kernel-parameters -- as code Doc : doc-guide : Fix a typo platform: x86: get rid of a non-existent document Add the RCU docs to the core-api manual Documentation: RCU: Add TOC tree hooks Documentation: RCU: Rename txt files to rst Documentation: RCU: Convert RCU UP systems to reST Documentation: RCU: Convert RCU linked list to reST Documentation: RCU: Convert RCU basic concepts to reST docs: filesystems: Remove uneeded .rst extension on toctables scripts/sphinx-pre-install: fix out-of-tree build docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/ Documentation: PGP: update for newer HW devices Documentation: Add section about CPU vulnerabilities for Spectre Documentation: platform: Delete x86-laptop-drivers.txt docs: Note that :c:func: should no longer be used ...
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner1-5/+1
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-14docs: kbuild: convert docs to ReST and rename to *.rstMauro Carvalho Chehab1-1/+1
The kbuild documentation clearly shows that the documents there are written at different times: some use markdown, some use their own peculiar logic to split sections. Convert everything to ReST without affecting too much the author's style and avoiding adding uneeded markups. The conversion is actually: - add blank lines and identation in order to identify paragraphs; - fix tables markups; - add some lists markups; - mark literal blocks; - adjust title markups. At its new index.rst, let's add a :orphan: while this is not linked to the main index.rst file, in order to avoid build warnings. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2019-06-08Merge tag 'char-misc-5.2-rc4' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver fixes from Greg KH: "Here are some small char and misc driver fixes for 5.2-rc4 to resolve a number of reported issues. The most "notable" one here is the kernel headers in proc^Wsysfs fixes. Those changes move the header file info into sysfs and fixes the build issues that you reported. Other than that, a bunch of small habanalabs driver fixes, some fpga driver fixes, and a few other tiny driver fixes. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: habanalabs: Read upper bits of trace buffer from RWPHI habanalabs: Fix virtual address access via debugfs for 2MB pages fpga: zynqmp-fpga: Correctly handle error pointer habanalabs: fix bug in checking huge page optimization habanalabs: Avoid using a non-initialized MMU cache mutex habanalabs: fix debugfs code uapi/habanalabs: add opcode for enable/disable device debug mode habanalabs: halt debug engines on user process close test_firmware: Use correct snprintf() limit genwqe: Prevent an integer overflow in the ioctl parport: Fix mem leak in parport_register_dev_model fpga: dfl: expand minor range when registering chrdev region fpga: dfl: Add lockdep classes for pdata->lock fpga: dfl: afu: Pass the correct device to dma_mapping_error() fpga: stratix10-soc: fix use-after-free on s10_init() w1: ds2408: Fix typo after 49695ac46861 (reset on output_write retry with readback) kheaders: Do not regenerate archive if config is not changed kheaders: Move from proc to sysfs lkdtm/bugs: Adjust recursion test to avoid elision lkdtm/usercopy: Moves the KERNEL_DS test to non-canonical
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 156Thomas Gleixner2-29/+2
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 59 temple place suite 330 boston ma 02111 1307 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1334 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner1-6/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-24parport: Fix mem leak in parport_register_dev_modelYueHaibing1-0/+2
BUG: memory leak unreferenced object 0xffff8881df48cda0 (size 16): comm "syz-executor.0", pid 5077, jiffies 4295994670 (age 22.280s) hex dump (first 16 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000d2d0d5fe>] parport_register_dev_model+0x141/0x6e0 [parport] [<00000000782f6dab>] 0xffffffffc15d1196 [<00000000d2ca6ae4>] platform_drv_probe+0x7e/0x100 [<00000000628c2a94>] really_probe+0x342/0x4d0 [<000000006874f5da>] driver_probe_device+0x8c/0x170 [<00000000424de37a>] __device_attach_driver+0xda/0x100 [<000000002acab09a>] bus_for_each_drv+0xfe/0x170 [<000000003d9e5f31>] __device_attach+0x190/0x230 [<0000000035d32f80>] bus_probe_device+0x123/0x140 [<00000000a05ba627>] device_add+0x7cc/0xce0 [<000000003f7560bf>] platform_device_add+0x230/0x3c0 [<000000002a0be07d>] 0xffffffffc15d0949 [<000000007361d8d2>] port_check+0x3b/0x50 [parport] [<000000004d67200f>] bus_for_each_dev+0x115/0x180 [<000000003ccfd11c>] __parport_register_driver+0x1f0/0x210 [parport] [<00000000987f06fc>] 0xffffffffc15d803e After commit 4e5a74f1db8d ("parport: Revert "parport: fix memory leak""), free_pardevice do not free par_dev->state, we should free it in error path of parport_register_dev_model before return. Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 4e5a74f1db8d ("parport: Revert "parport: fix memory leak"") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner1-0/+1
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier for more missed filesThomas Gleixner5-0/+5
Add SPDX license identifiers to all files which: - Have no license information of any form - Have MODULE_LICENCE("GPL*") inside which was used in the initial scan/conversion to ignore the file These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-09Merge tag 'dma-mapping-5.2' of git://git.infradead.org/users/hch/dma-mappingLinus Torvalds1-8/+10
Pull DMA mapping updates from Christoph Hellwig: - remove the already broken support for NULL dev arguments to the DMA API calls - Kconfig tidyups * tag 'dma-mapping-5.2' of git://git.infradead.org/users/hch/dma-mapping: dma-mapping: add a Kconfig symbol to indicate arch_dma_prep_coherent presence dma-mapping: remove an unnecessary NULL check x86/dma: Remove the x86_dma_fallback_dev hack dma-mapping: remove leftover NULL device support arm: use a dummy struct device for ISA DMA use of the DMA API pxa3xx-gcu: pass struct device to dma_mmap_coherent gbefb: switch to managed version of the DMA allocator da8xx-fb: pass struct device to DMA API functions parport_ip32: pass struct device to DMA API functions dma: select GENERIC_ALLOCATOR for DMA_REMAP
2019-04-25parport: ieee1284: mark expected switch fall-throughGustavo A. R. Silva1-1/+1
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. This patch fixes the following warning: drivers/parport/ieee1284.c: In function ‘parport_read’: drivers/parport/ieee1284.c:722:6: warning: this statement may fall through [-Wimplicit-fallthrough=] if (parport_negotiate (port, IEEE1284_MODE_NIBBLE)) { ^ drivers/parport/ieee1284.c:726:2: note: here case IEEE1284_MODE_NIBBLE: ^~~~ Warning level 3 was used: -Wimplicit-fallthrough=3 Notice that, in this particular case, the code comment is modified in accordance with what GCC is expecting to find. This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-08parport_ip32: pass struct device to DMA API functionsChristoph Hellwig1-8/+10
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-04-01Merge 5.1-rc3 into char-misc-nextGreg Kroah-Hartman3-41/+3
We want the char-misc fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-28parport_cs: Fix memory leak in parport_configYueHaibing1-2/+3
parport_probe() alloc parport device 'info', but while parport_config failed it does not free it. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-25Revert "parport: daisy: use new parport device model"Linus Torvalds3-41/+3
This reverts commit 1aec4211204d9463d1fd209eb50453de16254599. Steven Rostedt reports that it causes a hang at bootup and bisected it to this commit. The troigger is apparently a module alias for "parport_lowlevel" that points to "parport_pc", which causes a hang with modprobe -q -- parport_lowlevel blocking forever with a backtrace like this: wait_for_completion_killable+0x1c/0x28 call_usermodehelper_exec+0xa7/0x108 __request_module+0x351/0x3d8 get_lowlevel_driver+0x28/0x41 [parport] __parport_register_driver+0x39/0x1f4 [parport] daisy_drv_init+0x31/0x4f [parport] parport_bus_init+0x5d/0x7b [parport] parport_default_proc_register+0x26/0x1000 [parport] do_one_initcall+0xc2/0x1e0 do_init_module+0x50/0x1d4 load_module+0x1c2e/0x21b3 sys_init_module+0xef/0x117 Supid says: "Due to the new device model daisy driver will now try to find the parallel ports while trying to register its driver so that it can bind with them. Now, since daisy driver is loaded while parport bus is initialising the list of parport is still empty and it tries to load the lowlevel driver, which has an alias set to parport_pc, now causes a deadlock" But I don't think the daisy driver should be loaded by the parport initialization in the first place, so let's revert the whole change. If the daisy driver can just initialize separately on its own (like a driver should), instead of hooking into the parport init sequence directly, this issue probably would go away. Reported-and-bisected-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reported-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-02-13parport: daisy: use new parport device modelSudip Mukherjee3-3/+41
Modify parport daisy driver to use the new parallel port device model. Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-11parport_pc: fix find_superio io compare code, should use equal test.QiaoChong1-1/+1
In the original code before 181bf1e815a2 the loop was continuing until it finds the first matching superios[i].io and p->base. But after 181bf1e815a2 the logic changed and the loop now returns the pointer to the first mismatched array element which is then used in get_superio_dma() and get_superio_irq() and thus returning the wrong value. Fix the condition so that it now returns the correct pointer. Fixes: 181bf1e815a2 ("parport_pc: clean up the modified while loops using for") Cc: Alan Cox <alan@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: QiaoChong <qiaochong@loongson.cn> [rewrite the commit message] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-27parport: parport_pc: Mark expected switch fall-throughGustavo A. R. Silva1-1/+1
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 114730 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-08-18Merge tag 'char-misc-4.19-rc1' of ↵Linus Torvalds2-3/+8
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the bit set of char/misc drivers for 4.19-rc1 There is a lot here, much more than normal, seems like everyone is writing new driver subsystems these days... Anyway, major things here are: - new FSI driver subsystem, yet-another-powerpc low-level hardware bus - gnss, finally an in-kernel GPS subsystem to try to tame all of the crazy out-of-tree drivers that have been floating around for years, combined with some really hacky userspace implementations. This is only for GNSS receivers, but you have to start somewhere, and this is great to see. Other than that, there are new slimbus drivers, new coresight drivers, new fpga drivers, and loads of DT bindings for all of these and existing drivers. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits) android: binder: Rate-limit debug and userspace triggered err msgs fsi: sbefifo: Bump max command length fsi: scom: Fix NULL dereference misc: mic: SCIF Fix scif_get_new_port() error handling misc: cxl: changed asterisk position genwqe: card_base: Use true and false for boolean values misc: eeprom: assignment outside the if statement uio: potential double frees if __uio_register_device() fails eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency misc: ti-st: Fix memory leak in the error path of probe() android: binder: Show extra_buffers_size in trace firmware: vpd: Fix section enabled flag on vpd_section_destroy platform: goldfish: Retire pdev_bus goldfish: Use dedicated macros instead of manual bit shifting goldfish: Add missing includes to goldfish.h mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux dt-bindings: mux: add adi,adgs1408 Drivers: hv: vmbus: Cleanup synic memory free path Drivers: hv: vmbus: Remove use of slow_virt_to_phys() Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind() ...
2018-07-15parport: ieee1284: mark expected switch fall-throughsGustavo A. R. Silva1-1/+2
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-15parport: sunbpp: fix error return codeJulia Lawall1-2/+6
Return an error code on failure. Change leading spaces to tab on the first if. Problem found using Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-07parport: parport_serial: Add WCH CH382L PCIe single parallel port supportColin Ian King1-0/+9
The WCH CH382L PCIe adapter has 1 parallel port but unlike the similar WCH CH328 adapter there are no serial ports connected to it. Enable this adapter with the addition of the appropriate PCIe IDs and board support config. PCIe device ID 1c00:3050: 02:00.0 Serial controller: Device 1c00:3050 (rev 10) (prog-if 05 [16850]) Subsystem: Device 1c00:3050 Flags: fast devsel, IRQ 16 I/O ports at 2000 [size=256] Memory at d0000000 (32-bit, prefetchable) [size=32K] I/O ports at 2100 [size=4] Expansion ROM at b0200000 [disabled] [size=32K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/32 Maskable+ 64bit+ Capabilities: [80] Express Legacy Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Kernel driver in use: parport_pc Kernel modules: parport_pc, parport_serial Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-15docs: Fix some broken referencesMauro Carvalho Chehab1-3/+3
As we move stuff around, some doc references are broken. Fix some of them via this script: ./scripts/documentation-file-ref-check --fix Manually checked if the produced result is valid, removing a few false-positives. Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Coly Li <colyli@suse.de> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by: Jonathan Corbet <corbet@lwn.net>
2018-04-04Merge tag 'char-misc-4.17-rc1' of ↵Linus Torvalds3-81/+53
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc updates from Greg KH: "Here is the big set of char/misc driver patches for 4.17-rc1. There are a lot of little things in here, nothing huge, but all important to the different hardware types involved: - thunderbolt driver updates - parport updates (people still care...) - nvmem driver updates - mei updates (as always) - hwtracing driver updates - hyperv driver updates - extcon driver updates - ... and a handful of even smaller driver subsystem and individual driver updates All of these have been in linux-next with no reported issues" * tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits) hwtracing: Add HW tracing support menu intel_th: Add ACPI glue layer intel_th: Allow forcing host mode through drvdata intel_th: Pick up irq number from resources intel_th: Don't touch switch routing in host mode intel_th: Use correct method of finding hub intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate stm class: Make dummy's master/channel ranges configurable stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate MAINTAINERS: Bestow upon myself the care for drivers/hwtracing hv: add SPDX license id to Kconfig hv: add SPDX license to trace Drivers: hv: vmbus: do not mark HV_PCIE as perf_device Drivers: hv: vmbus: respect what we get from hv_get_synint_state() /dev/mem: Avoid overwriting "err" in read_mem() eeprom: at24: use SPDX identifier instead of GPL boiler-plate eeprom: at24: simplify the i2c functionality checking eeprom: at24: fix a line break eeprom: at24: tweak newlines eeprom: at24: refactor at24_probe() ...
2018-04-04Merge tag 'tty-4.17-rc1' of ↵Linus Torvalds1-3/+0
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver updates from Greg KH: "Here is the big set of tty and serial driver patches for 4.17-rc1 Not all that big really, most are just small fixes and additions to existing drivers. There's a bunch of work on the imx serial driver recently for some reason, and a new embedded serial driver added as well. Full details are in the shortlog. All of these have been in the linux-next tree for a while with no reported issues" * tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits) serial: expose buf_overrun count through proc interface serial: mvebu-uart: fix tx lost characters tty: serial: msm_geni_serial: Fix return value check in qcom_geni_serial_probe() tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP 8250-men-mcb: add support for 16z025 and 16z057 powerpc: Mark the variable earlycon_acpi_spcr_enable maybe_unused serial: stm32: fix initialization of RS485 mode ARM: dts: STi: Remove "console=ttyASN" from bootargs for STi boards vt: change SGR 21 to follow the standards serdev: Fix typo in serdev_device_alloc ARM: dts: STi: Fix aliases property name for STi boards tty: st-asc: Update tty alias serial: stm32: add support for RS485 hardware control mode dt-bindings: serial: stm32: add RS485 optional properties selftests: add devpts selftests devpts: comment devpts_mntget() devpts: resolve devpts bind-mounts devpts: hoist out check for DEVPTS_SUPER_MAGIC serial: 8250: Add Nuvoton NPCM UART serial: mxs-auart: disable clks of Alphascale ASM9260 ...
2018-03-27parisc/parport_gsc: Use NULL to avoid sparse warningHelge Deller1-1/+1
Signed-off-by: Helge Deller <deller@gmx.de>
2018-03-14parport: Replace short License header by SPDX identifierAndy Shevchenko1-7/+1
No functional changes involved. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Sort headers alphabeticallyAndy Shevchenko1-5/+5
While here, remove init.h inclusion since we are not using it directly and module.h will do this for us. No functional changes intended. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Switch to use module_pci_driver() macroAndy Shevchenko1-15/+1
Eliminate some boilerplate code by using module_pci_driver() instead of init/exit, moving the salient bits from init into probe. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Convert printk(KERN_WARN) to dev_warn()Andy Shevchenko1-6/+5
dev_warn() will print device name with associated driver, no need to keep this open coded. While here, adjust indentation in the rest of dev_dbg() calls. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Don't shadow error codes in ->probe()Andy Shevchenko1-6/+6
When ->probe() calls helper functions return theirs error codes instead of shadowing them. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Convert to use managed functions pcim_* and devm_*Andy Shevchenko1-10/+5
This makes the error handling much more simpler than open-coding everything and in addition makes the probe function smaller an tidier. Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: PCI core handles power state for usAndy Shevchenko1-28/+12
There is no need to repeat the work that is already done in the PCI driver core. The patch removes excerpts from suspend and resume callbacks. Note that there is no more calls performed to enable or disable a PCI device during suspend-resume cycle. Nowadays they seems to be superflous. Someone can read more in [1]. While here, convert calls to new driver API. [1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: Add support for BrainBoxes PX272/PX306 MIO cardAndy Shevchenko1-0/+12
This adds support for BrainBoxes Multi I/O cards (4+1 serial + 1 parallel port): 02:00.0 0702: 135a:4100 (rev 02) Subsystem: 135a:0443 Flags: fast devsel, IRQ 18 Memory at f7d02000 (32-bit, non-prefetchable) [size=128] I/O ports at e000 [size=128] I/O ports at e080 [size=64] I/O ports at e0c0 [size=16] Memory at f7d01000 (32-bit, non-prefetchable) [size=128] Memory at f7d00000 (32-bit, non-prefetchable) [size=128] Capabilities: [50] MSI: Enable- Count=1/4 Maskable- 64bit+ Capabilities: [78] Power Management version 3 Capabilities: [80] Express Legacy Endpoint, MSI 01 Capabilities: [100] Virtual Channel Capabilities: [800] Advanced Error Reporting Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: ax88796: Delete an unnecessary variable initialisation in ↵Markus Elfring1-1/+1
parport_ax88796_probe() The local variable "pp" will eventually be set to an appropriate pointer a bit later. Thus omit the explicit initialisation at the beginning. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: ax88796: Improve a size determination in parport_ax88796_probe()Markus Elfring1-1/+1
Replace the specification of a data structure by a pointer dereference as the parameter for the operator "sizeof" to make the corresponding size determination a bit safer according to the Linux coding style convention. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport: ax88796: Delete an error message for a failed memory allocation in ↵Markus Elfring1-3/+1
parport_ax88796_probe() Omit an extra message for a memory allocation failure in this function. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-14parport_pc: Add support for WCH CH382L PCI-E single parallel port card.Alexander Gerasiov1-0/+4
WCH CH382L is a PCI-E adapter with 1 parallel port. It is similair to CH382 but serial ports are not soldered on board. Detected as Serial controller: Device 1c00:3050 (rev 10) (prog-if 05 [16850]) Signed-off-by: Alexander Gerasiov <gq@redlab-i.ru> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28serial, pci_ids: Move duplicate IDs to PCI IDs databaseAndy Shevchenko1-3/+0
PCI ID database is for IDs used across several drivers. Here is the case for SUNIX combo cards. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-16Merge tag 'char-misc-4.15-rc1' of ↵Linus Torvalds1-1/+1
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc updates from Greg KH: "Here is the big set of char/misc and other driver subsystem patches for 4.15-rc1. There are small changes all over here, hyperv driver updates, pcmcia driver updates, w1 driver updats, vme driver updates, nvmem driver updates, and lots of other little one-off driver updates as well. The shortlog has the full details. All of these have been in linux-next for quite a while with no reported issues" * tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits) VME: Return -EBUSY when DMA list in use w1: keep balance of mutex locks and refcnts MAINTAINERS: Update VME subsystem tree. nvmem: sunxi-sid: add support for A64/H5's SID controller nvmem: imx-ocotp: Update module description nvmem: imx-ocotp: Enable i.MX7D OTP write support nvmem: imx-ocotp: Add i.MX7D timing write clock setup support nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function nvmem: imx-ocotp: Add support for banked OTP addressing nvmem: imx-ocotp: Pass parameters via a struct nvmem: imx-ocotp: Restrict OTP write to IMX6 processors nvmem: uniphier: add UniPhier eFuse driver dt-bindings: nvmem: add description for UniPhier eFuse nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset nvmem: qfprom: fix different address space warnings of sparse nvmem: mtk-efuse: fix different address space warnings of sparse nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it thunderbolt: tb: fix use after free in tb_activate_pcie_devices MAINTAINERS: Add git tree for Thunderbolt development ...
2017-11-13Merge branch 'timers-core-for-linus' of ↵Linus Torvalds1-14/+7
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timer updates from Thomas Gleixner: "Yet another big pile of changes: - More year 2038 work from Arnd slowly reaching the point where we need to think about the syscalls themself. - A new timer function which allows to conditionally (re)arm a timer only when it's either not running or the new expiry time is sooner than the armed expiry time. This allows to use a single timer for multiple timeout requirements w/o caring about the first expiry time at the call site. - A new NMI safe accessor to clock real time for the printk timestamp work. Can be used by tracing, perf as well if required. - A large number of timer setup conversions from Kees which got collected here because either maintainers requested so or they simply got ignored. As Kees pointed out already there are a few trivial merge conflicts and some redundant commits which was unavoidable due to the size of this conversion effort. - Avoid a redundant iteration in the timer wheel softirq processing. - Provide a mechanism to treat RTC implementations depending on their hardware properties, i.e. don't inflict the write at the 0.5 seconds boundary which originates from the PC CMOS RTC to all RTCs. No functional change as drivers need to be updated separately. - The usual small updates to core code clocksource drivers. Nothing really exciting" * 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits) timers: Add a function to start/reduce a timer pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday() timer: Prepare to change all DEFINE_TIMER() callbacks netfilter: ipvs: Convert timers to use timer_setup() scsi: qla2xxx: Convert timers to use timer_setup() block/aoe: discover_timer: Convert timers to use timer_setup() ide: Convert timers to use timer_setup() drbd: Convert timers to use timer_setup() mailbox: Convert timers to use timer_setup() crypto: Convert timers to use timer_setup() drivers/pcmcia: omap1: Fix error in automated timer conversion ARM: footbridge: Fix typo in timer conversion drivers/sgi-xp: Convert timers to use timer_setup() drivers/pcmcia: Convert timers to use timer_setup() drivers/memstick: Convert timers to use timer_setup() drivers/macintosh: Convert timers to use timer_setup() hwrng/xgene-rng: Convert timers to use timer_setup() auxdisplay: Convert timers to use timer_setup() sparc/led: Convert timers to use timer_setup() mips: ip22/32: Convert timers to use timer_setup() ...
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman5-0/+5
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>