summaryrefslogtreecommitdiffstats
path: root/drivers/opp
AgeCommit message (Collapse)AuthorFilesLines
2019-11-11PM / OPP: Support adjusting OPP voltages at runtimeStephen Boyd1-0/+69
On some SoCs the Adaptive Voltage Scaling (AVS) technique is employed to optimize the operating voltage of a device. At a given frequency, the hardware monitors dynamic factors and either makes a suggestion for how much to adjust a voltage for the current frequency, or it automatically adjusts the voltage without software intervention. Add an API to the OPP library for the former case, so that AVS type devices can update the voltages for an OPP when the hardware determines the voltage should change. The assumption is that drivers like CPUfreq or devfreq will register for the OPP notifiers and adjust the voltage according to suggestions that AVS makes. This patch is derived from [1] submitted by Stephen. [1] https://lore.kernel.org/patchwork/patch/599279/ Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> [Roger Lu: Changed to rcu less implementation] Signed-off-by: Roger Lu <roger.lu@mediatek.com> [s.nawrocki@samsung.com: added handling of OPP min/max voltage] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-10-23opp: Reinitialize the list_kref before adding the static OPPs againViresh Kumar1-0/+7
The list_kref reaches a count of 0 when all the static OPPs are removed, for example when dev_pm_opp_of_cpumask_remove_table() is called, though the actual OPP table may not get freed as it may still be referenced by other parts of the kernel, like from a call to dev_pm_opp_set_supported_hw(). And if we call dev_pm_opp_of_cpumask_add_table() again at this point, we must reinitialize the list_kref otherwise the kernel will hit a WARN() in kref infrastructure for incrementing a kref with value 0. Fixes: 11e1a1648298 ("opp: Don't decrement uninitialized list_kref") Reported-by: Dmitry Osipenko <digetx@gmail.com> Tested-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-10-21opp: core: Revert "add regulators enable and disable"Marek Szyprowski1-13/+3
All the drivers, which use the OPP framework control regulators, which are already enabled. Typically those regulators are also system critical, due to providing power to CPU core or system buses. It turned out that there are cases, where calling regulator_enable() on such boot-enabled regulator has side-effects and might change its initial voltage due to performing initial voltage balancing without all restrictions from the consumers. Until this issue becomes finally solved in regulator core, avoid calling regulator_enable()/disable() from the OPP framework. This reverts commit 7f93ff73f7c8c8bfa6be33bcc16470b0b44682aa. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-10-10opp: of: drop incorrect lockdep_assert_held()Viresh Kumar1-2/+0
_find_opp_of_np() doesn't traverse the list of OPP tables but instead just the entries within an OPP table and so only requires to lock the OPP table itself. The lockdep_assert_held() was added there by mistake and isn't really required. Fixes: 5d6d106fa455 ("OPP: Populate required opp tables from "required-opps" property") Cc: v5.0+ <stable@vger.kernel.org> # v5.0+ Reported-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-07-26opp: of: Support multiple suspend OPPs defined in DTAnson Huang1-3/+6
With property "opp-supported-hw" introduced, the OPP table in DT could be a large OPP table and ONLY a subset of OPPs are available, based on the version of the hardware running on. That introduces restriction of using "opp-suspend" property to define the suspend OPP, as we are NOT sure if the OPP containing "opp-suspend" property is available for the hardware running on, and the of opp core does NOT allow multiple suspend OPPs defined in DT OPP table. To eliminate this restrition, make of opp core allow multiple suspend OPPs defined in DT, and pick the OPP with highest rate and with "opp-suspend" property present to be suspend OPP, it can speed up the suspend/resume process. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-07-26opp: core: add regulators enable and disablek.konieczny@partner.samsung.com1-3/+13
Add enable regulators to dev_pm_opp_set_regulators() and disable regulators to dev_pm_opp_put_regulators(). Even if bootloader leaves regulators enabled, they should be enabled in kernel in order to increase the reference count. Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-07-26opp: Don't decrement uninitialized list_krefViresh Kumar2-17/+5
The list_kref was added for static OPPs and to track their users. The kref is initialized while the static OPPs are added, but removed unconditionally even if the static OPPs were never added. This causes refcount mismatch warnings currently. Fix that by always initializing the kref when the OPP table is first initialized. The refcount is later incremented only for the second user onwards. Fixes: d0e8ae6c26da ("OPP: Create separate kref for static OPPs list") Reported-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-07-26opp: Add dev_pm_opp_find_level_exact()Niklas Cassel1-0/+48
Since the performance states in the OPP table are unique, implement a dev_pm_opp_find_level_exact() in order to be able to fetch a specific OPP. Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> [ Viresh: Updated commit log ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-07-26opp: Return genpd virtual devices from dev_pm_opp_attach_genpd()Viresh Kumar1-1/+5
The cpufreq drivers don't need to do runtime PM operations on the virtual devices returned by dev_pm_domain_attach_by_name() and so the virtual devices weren't shared with the callers of dev_pm_opp_attach_genpd() earlier. But the IO device drivers would want to do that. This patch updates the prototype of dev_pm_opp_attach_genpd() to accept another argument to return the pointer to the array of genpd virtual devices. Reported-by: Rajendra Nayak <rnayak@codeaurora.org> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-07-26opp: Not all power-domains are scalableViresh Kumar1-9/+5
A device may have multiple power-domains and not all of them may be scalable (i.e. support performance states). But dev_pm_opp_attach_genpd() doesn't take that into account currently. Fix that by not verifying the names argument with "power-domain-names" DT property and finding the index into the required-opps array. The names argument will anyway get verified later on when we call dev_pm_domain_attach_by_name(). Fixes: 6319aee10e53 ("opp: Attach genpds to devices from within OPP core") Reported-by: Rajendra Nayak <rnayak@codeaurora.org> Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-07-15Merge tag 'pci-v5.3-changes' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Enumeration changes: - Evaluate PCI Boot Configuration _DSM to learn if firmware wants us to preserve its resource assignments (Benjamin Herrenschmidt) - Simplify resource distribution (Nicholas Johnson) - Decode 32 GT/s link speed (Gustavo Pimentel) Virtualization: - Fix incorrect caching of VF config space size (Alex Williamson) - Fix VF driver probing sysfs knobs (Alex Williamson) Peer-to-peer DMA: - Fix dma_virt_ops check (Logan Gunthorpe) Altera host bridge driver: - Allow building as module (Ley Foon Tan) Armada 8K host bridge driver: - add PHYs support (Miquel Raynal) DesignWare host bridge driver: - Export APIs to support removable loadable module (Vidya Sagar) - Enable Relaxed Ordering erratum workaround only on Tegra20 & Tegra30 (Vidya Sagar) Hyper-V host bridge driver: - Fix use-after-free in eject (Dexuan Cui) Mobiveil host bridge driver: - Clean up and fix many issues, including non-identify mapped windows, 64-bit windows, multi-MSI, class code, INTx clearing (Hou Zhiqiang) Qualcomm host bridge driver: - Use clk bulk API for 2.4.0 controllers (Bjorn Andersson) - Add QCS404 support (Bjorn Andersson) - Assert PERST for at least 100ms (Niklas Cassel) R-Car host bridge driver: - Add r8a774a1 DT support (Biju Das) Tegra host bridge driver: - Add support for Gen2, opportunistic UpdateFC and ACK (PCIe protocol details) AER, GPIO-based PERST# (Manikanta Maddireddy) - Fix many issues, including power-on failure cases, interrupt masking in suspend, UPHY settings, AFI dynamic clock gating, pending DLL transactions (Manikanta Maddireddy) Xilinx host bridge driver: - Fix NWL Multi-MSI programming (Bharat Kumar Gogada) Endpoint support: - Fix 64bit BAR support (Alan Mikhak) - Fix pcitest build issues (Alan Mikhak, Andy Shevchenko) Bug fixes: - Fix NVIDIA GPU multi-function power dependencies (Abhishek Sahu) - Fix NVIDIA GPU HDA enablement issue (Lukas Wunner) - Ignore lockdep for sysfs "remove" (Marek Vasut) Misc: - Convert docs to reST (Changbin Du, Mauro Carvalho Chehab)" * tag 'pci-v5.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (107 commits) PCI: Enable NVIDIA HDA controllers tools: PCI: Fix installation when `make tools/pci_install` PCI: dwc: pci-dra7xx: Fix compilation when !CONFIG_GPIOLIB PCI: Fix typos and whitespace errors PCI: mobiveil: Fix INTx interrupt clearing in mobiveil_pcie_isr() PCI: mobiveil: Fix infinite-loop in the INTx handling function PCI: mobiveil: Move PCIe PIO enablement out of inbound window routine PCI: mobiveil: Add upper 32-bit PCI base address setup in inbound window PCI: mobiveil: Add upper 32-bit CPU base address setup in outbound window PCI: mobiveil: Mask out hardcoded bits in inbound/outbound windows setup PCI: mobiveil: Clear the control fields before updating it PCI: mobiveil: Add configured inbound windows counter PCI: mobiveil: Fix the valid check for inbound and outbound windows PCI: mobiveil: Clean-up program_{ib/ob}_windows() PCI: mobiveil: Remove an unnecessary return value check PCI: mobiveil: Fix error return values PCI: mobiveil: Refactor the MEM/IO outbound window initialization PCI: mobiveil: Make some register updates more readable PCI: mobiveil: Reformat the code for readability dt-bindings: PCI: mobiveil: Change gpio_slave and apb_csr to optional ...
2019-06-26Merge branch 'opp/linux-next' of ↵Rafael J. Wysocki2-87/+117
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm Pull operating performance points (OPP) framework changes for v5.3 from Viresh Kumar: "This pull request contains: - OPP core changes to support a wider range of devices, like IO devices (Rajendra Nayak and Stehpen Boyd). - Fixes around genpd_virt_devs (Viresh Kumar). - Fix for platform with set_opp() callback (Dmitry Osipenko)." * 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: opp: Don't use IS_ERR on invalid supplies opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votes opp: Don't overwrite rounded clk rate opp: Allocate genpd_virt_devs from dev_pm_opp_attach_genpd() opp: Attach genpds to devices from within OPP core
2019-06-24opp: Don't use IS_ERR on invalid suppliesDmitry Osipenko1-1/+1
_set_opp_custom() receives a set of OPP supplies as its arguments and the caller of it passes NULL when the supplies are not valid. But _set_opp_custom(), by mistake, checks for error by performing IS_ERR(old_supply) on it which will always evaluate to false. The problem was spotted during of testing of upcoming update for the NVIDIA Tegra CPUFreq driver. Cc: stable <stable@vger.kernel.org> Fixes: 7e535993fa4f ("OPP: Separate out custom OPP handler specific code") Reported-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> [ Viresh: Massaged changelog ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner5-20/+5
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-17opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votesRajendra Nayak1-8/+13
For devices with performance state, we use dev_pm_opp_set_rate() to set the appropriate clk rate and the performance state. We do need a way to remove the performance state vote when we idle the device and turn the clocks off. Use dev_pm_opp_set_rate() with freq = 0 to achieve this. Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> [ Viresh: Updated _set_required_opps() to handle the !opp case ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-06-17opp: Don't overwrite rounded clk rateStephen Boyd1-5/+10
The OPP table normally contains 'fmax' values corresponding to the voltage or performance levels of each OPP, but we don't necessarily want all the devices to run at fmax all the time. Running at fmax makes sense for devices like CPU/GPU, which have a finite amount of work to do and since a specific amount of energy is consumed at an OPP, its better to run at the highest possible frequency for that voltage value. On the other hand, we have IO devices which need to run at specific frequencies only for their proper functioning, instead of maximum possible frequency. The OPP core currently roundup to the next possible OPP for a frequency and select the fmax value. To support the IO devices by the OPP core, lets do the roundup to fetch the voltage or performance state values, but not use the OPP frequency value. Rather use the value returned by clk_round_rate(). The current user, cpufreq, of dev_pm_opp_set_rate() already does the rounding to the next OPP before calling this routine and it won't have any side affects because of this change. Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> [ Viresh: Massaged changelog, added comment and use temp_opp variable instead ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-06-14docs: power: convert docs to ReST and rename to *.rstMauro Carvalho Chehab1-1/+1
Convert the PM documents to ReST, in order to allow them to build with Sphinx. The conversion is actually: - add blank lines and indentation in order to identify paragraphs; - fix tables markups; - add some lists markups; - mark literal blocks; - adjust title markups. At its new index.rst, let's add a :orphan: while this is not linked to the main index.rst file, in order to avoid build warnings. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner2-0/+2
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-20opp: Allocate genpd_virt_devs from dev_pm_opp_attach_genpd()Viresh Kumar2-28/+12
Currently the space for the array of virtual devices is allocated along with the OPP table, but that isn't going to work well from now onwards. For single power domain case, a driver can either use the original device structure for setting the performance state (if genpd attached with dev_pm_domain_attach()) or use the virtual device structure (if genpd attached with dev_pm_domain_attach_by_name(), which returns the virtual device) and so we can't know in advance if we are going to need genpd_virt_devs array or not. Lets delay the allocation a bit and do it along with dev_pm_opp_attach_genpd() rather. The deallocation is done from dev_pm_opp_detach_genpd(). Tested-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-05-20opp: Attach genpds to devices from within OPP coreViresh Kumar1-46/+82
The OPP core requires the virtual device pointers to set performance state on behalf of the device, for the multiple power domain case. The genpd API (dev_pm_domain_attach_by_name()) has evolved now to support even the single power domain case and that lets us add common code for handling both the cases more efficiently. The virtual device structure returned by dev_pm_domain_attach_by_name() isn't normally used by the cpufreq drivers as they don't manage power on/off of the domains and so is only useful for the OPP core. This patch moves all the complexity into the OPP core to make the end drivers simple. The earlier APIs dev_pm_opp_{set|put}_genpd_virt_dev() are reworked into dev_pm_opp_{attach|detach}_genpd(). The new helper dev_pm_opp_attach_genpd() accepts a NULL terminated array of strings which contains names of all the genpd's to attach. It then attaches all the domains and saves the pointers to the virtual devices. The other helper undo the work done by this helper. Tested-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-04-10OPP: Introduce dev_pm_opp_find_freq_ceil_by_volt()Andrew-sh.Cheng1-0/+54
This patch introduces a new helper routine in the OPP core, which returns the OPP with the highest frequency which has voltage less than or equal to the target voltage passed to the helper. Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com> [ Viresh: Massaged the commit log and renamed the helper with some cleanups. ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-03-12PM / OPP: Update performance state when freq == old_freqViresh Kumar1-1/+1
At boot up, CPUFreq core performs a sanity check to see if the system is running at a frequency defined in the frequency table of the CPU. If so, we try to find a valid frequency (lowest frequency greater than the currently programmed frequency) from the table and set it. When the call reaches dev_pm_opp_set_rate(), it calls _find_freq_ceil(opp_table, &old_freq) to find the previously configured OPP and this call also updates the old_freq. This eventually sets the old_freq == freq (new target requested by cpufreq core) and we skip updating the performance state in this case. Fix this by also updating the performance state when the old_freq == freq. Fixes: ca1b5d77b1c6 ("OPP: Configure all required OPPs") Cc: v5.0 <stable@vger.kernel.org> # v5.0 Reported-by: Niklas Cassel <niklas.cassel@linaro.org> Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-03-11OPP: Fix handling of multiple power domainsRajendra Nayak1-2/+14
We seem to rely on the number of phandles specified in the 'required-opps' property to identify cases where a device is associated with multiple power domains and hence would have multiple virtual devices that have to be dealt with. In cases where we do have devices with multiple power domains but with only one of them being scalable, this logic seems to fail. Instead read the number of power domains from DT to identify such cases. Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-03-06Merge tag 'pm-5.1-rc1' of ↵Linus Torvalds4-104/+142
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management updates from Rafael Wysocki: "These are PM-runtime framework changes to use ktime instead of jiffies for accounting, new PM core flag to mark devices that don't need any form of power management, cpuidle updates including driver API documentation and a new governor, cpufreq updates including a new driver for Armada 8K, thermal cleanups and more, some energy-aware scheduling (EAS) enabling changes, new chips support in the intel_idle and RAPL drivers and assorted cleanups in some other places. Specifics: - Update the PM-runtime framework to use ktime instead of jiffies for accounting (Thara Gopinath, Vincent Guittot) - Optimize the autosuspend code in the PM-runtime framework somewhat (Ladislav Michl) - Add a PM core flag to mark devices that don't need any form of power management (Sudeep Holla) - Introduce driver API documentation for cpuidle and add a new cpuidle governor for tickless systems (Rafael Wysocki) - Add Jacobsville support to the intel_idle driver (Zhang Rui) - Clean up a cpuidle core header file and the cpuidle-dt and ACPI processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam) - Add new cpufreq driver for Armada 8K (Gregory Clement) - Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar, Amit Kucheria) - Add support for light-weight tear-down and bring-up of CPUs to the cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar) - Fix cpu_cooling Kconfig dependencies, add support for CPU cooling auto-registration to the cpufreq core and use it in multiple cpufreq drivers (Amit Kucheria) - Fix some minor issues and do some cleanups in the davinci, e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers (Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel, Taniya Das, Viresh Kumar) - Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng Wang) - Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu, Rafael Wysocki) - Clean up multiple cpufreq drivers (Yangtao Li) - Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas Bulwahn) - Add support for exposing the Energy Model via debugfs and make multiple cpufreq drivers register an Energy Model to support energy-aware scheduling (Quentin Perret, Dietmar Eggemann, Matthias Kaehlcke) - Add Ice Lake mobile and Jacobsville support to the Intel RAPL power-capping driver (Gayatri Kammela, Zhang Rui) - Add a power estimation helper to the operating performance points (OPP) framework and clean up a core function in it (Quentin Perret, Viresh Kumar) - Make minor improvements in the generic power domains (genpd), OPP and system suspend frameworks and in the PM core (Aditya Pakki, Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li)" * tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (80 commits) cpufreq: kryo: Release OPP tables on module removal cpufreq: ap806: add missing of_node_put after of_device_is_available cpufreq: acpi-cpufreq: Report if CPU doesn't support boost technologies cpufreq: Pass updated policy to driver ->setpolicy() callback cpufreq: Fix two debug messages in cpufreq_set_policy() cpufreq: Reorder and simplify cpufreq_update_policy() cpufreq: Add kerneldoc comments for two core functions PM / core: Add support to skip power management in device/driver model cpufreq: intel_pstate: Rework iowait boosting to be less aggressive cpufreq: intel_pstate: Eliminate intel_pstate_get_base_pstate() cpufreq: intel_pstate: Avoid redundant initialization of local vars powercap/intel_rapl: add Ice Lake mobile ACPI / processor: Set P_LVL{2,3} idle state descriptions cpufreq / cppc: Work around for Hisilicon CPPC cpufreq ACPI / CPPC: Add a helper to get desired performance cpufreq: davinci: move configuration to include/linux/platform_data cpufreq: speedstep: convert BUG() to BUG_ON() cpufreq: powernv: fix missing check of return value in init_powernv_pstates() cpufreq: longhaul: remove unneeded semicolon cpufreq: pcc-cpufreq: remove unneeded semicolon ..
2019-02-15Merge tag 'qcom-drivers-for-5.1' of ↵Arnd Bergmann3-0/+22
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/drivers Qualcomm ARM Based Driver Updates for v5.1 * Add Qualcomm RPMh power domain driver and related changes * Fix issues with sleep/wake sets and batch API in RPMh * Update MAINTAINERS Qualcomm entry * Fixup RMTFS-mem sysfs and uevents * Fix error handling in GSBI * Add SMD-RPM compatible entry for SDM660 * tag 'qcom-drivers-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: soc: qcom: smd-rpm: Add sdm660 compatible soc: qcom: gsbi: Fix error handling in gsbi_probe() soc: qcom: rpmh: Avoid accessing freed memory from batch API drivers: qcom: rpmh: avoid sending sleep/wake sets immediately soc: qcom: rmtfs-mem: Make sysfs attributes world-readable soc: qcom: rmtfs-mem: Add class to enable uevents soc: qcom: update config dependencies for QCOM_RPMPD soc: qcom: rpmpd: Drop family A RPM dependency MAINTAINERS: update list of qcom drivers soc: qcom: rpmhpd: Mark mx as a parent for cx soc: qcom: rpmhpd: Add RPMh power domain driver soc: qcom: rpmpd: Add support for get/set performance state soc: qcom: rpmpd: Add a Power domain driver to model corners dt-bindings: power: Add qcom rpm power domain driver bindings OPP: Add support for parsing the 'opp-level' property dt-bindings: opp: Introduce opp-level bindings Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2019-02-12Merge branch 'opp/linux-next' of ↵Rafael J. Wysocki4-104/+142
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm into pm-opp Pull operating performance points (OPP) framework updates for v5.1 from Viresh Kumar: "This pull request contains following changes: - Introduced new OPP helper for power-estimation and used it in several cpufreq drivers (Quentin Perret, Matthias Kaehlcke, Dietmar Eggemann, and Yangtao Li). - OPP Debugfs cleanup (Greg KH). - OPP core cleanup (Viresh Kumar)." * 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: cpufreq: OMAP: Register an Energy Model cpufreq: imx6q: Register an Energy Model opp: no need to check return value of debugfs_create functions cpufreq: mediatek: Register an Energy Model cpufreq: scmi: Register an Energy Model cpufreq: arm_big_little: Register an Energy Model cpufreq: scpi: Register an Energy Model cpufreq: dt: Register an Energy Model PM / OPP: Introduce a power estimation helper PM / OPP: Remove unused parameter of _generic_set_opp_clk_only()
2019-02-07opp: no need to check return value of debugfs_create functionsGreg Kroah-Hartman3-98/+38
When calling debugfs functions, there is no need to ever check the return value. The function can work or not, but the code logic should never do something different based on this. Cc: Viresh Kumar <vireshk@kernel.org> Cc: Nishanth Menon <nm@ti.com> Cc: Stephen Boyd <sboyd@kernel.org> Cc: linux-pm@vger.kernel.org Reviewed-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-02-07PM / OPP: Introduce a power estimation helperQuentin Perret1-0/+99
The Energy Model (EM) framework provides an API to let drivers register the active power of CPUs. The drivers are expected to provide a callback method which estimates the power consumed by a CPU at each available performance levels. How exactly this should be implemented, however, depends on the platform. On some systems, PM_OPP knows the voltage and frequency at which CPUs can run. When coupled with the CPU 'capacitance' (as provided by the 'dynamic-power-coefficient' devicetree binding), it is possible to estimate the dynamic power consumption of a CPU as P = C * V^2 * f, with C its capacitance and V and f respectively the voltage and frequency of the OPP. The Intelligent Power Allocator (IPA) thermal governor already implements that estimation method, in the thermal framework. However, this power estimation method can be applied to any platform where all the parameters are known (C, V and f), and not only those suffering thermal issues. As such, the code implementing this feature can be re-used to also populate the EM framework now used by EAS. As a first step, introduce in PM_OPP a helper function which CPUFreq drivers can use to register into the EM framework. This duplicates the power estimation done in IPA until it can be migrated to using the EM framework. This will be done later, once the EM framework has support for at least all platforms currently supported by IPA. Signed-off-by: Quentin Perret <quentin.perret@arm.com> Tested-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-02-07PM / OPP: Remove unused parameter of _generic_set_opp_clk_only()Viresh Kumar1-6/+5
The previous frequency value isn't getting used in the routine _generic_set_opp_clk_only(), drop it. Reviewed-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2019-01-22OPP: Add support for parsing the 'opp-level' propertyRajendra Nayak3-0/+22
Now that the OPP bindings are updated to include an optional 'opp-level' property, add support to parse it from device tree and store it as part of dev_pm_opp structure. Also add and export an helper 'dev_pm_opp_get_level()' that can be used to get the level value read from device tree when present. Reviewed-by: Stephen Boyd <swboyd@chromium.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
2019-01-04cpufreq: scpi/scmi: Fix freeing of dynamic OPPsViresh Kumar1-5/+58
Since the commit 2a4eb7358aba "OPP: Don't remove dynamic OPPs from _dev_pm_opp_remove_table()", dynamically created OPP aren't automatically removed anymore by dev_pm_opp_cpumask_remove_table(). This affects the scpi and scmi cpufreq drivers which no longer free OPPs on failures or on invocations of the policy->exit() callback. Create a generic OPP helper dev_pm_opp_remove_all_dynamic() which can be called from these drivers instead of dev_pm_opp_cpumask_remove_table(). In dev_pm_opp_remove_all_dynamic(), we need to make sure that the opp_list isn't getting accessed simultaneously from other parts of the OPP core while the helper is freeing dynamic OPPs, i.e. we can't drop the opp_table->lock while traversing through the OPP list. And to accomplish that, this patch also creates _opp_kref_release_unlocked() which can be called from this new helper with the opp_table lock already held. Cc: 4.20 <stable@vger.kernel.org> # v4.20 Reported-by: Valentin Schneider <valentin.schneider@arm.com> Fixes: 2a4eb7358aba "OPP: Don't remove dynamic OPPs from _dev_pm_opp_remove_table()" Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Tested-by: Valentin Schneider <valentin.schneider@arm.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-12-14Merge branch 'opp/genpd/propagation' into opp/linux-nextViresh Kumar3-111/+552
2018-12-14OPP: Don't return 0 on error from of_get_required_opp_performance_state()Viresh Kumar1-5/+5
of_get_required_opp_performance_state() returns 0 on errors currently and a positive performance state otherwise. Since 0 is a valid performance state (representing off), it would be better if this routine returns negative values on error. That will also make it behave similar to dev_pm_opp_xlate_performance_state(), which also returns performance states and returns negative values on error. Change the return type of the function to "int" in order to return negative values. This doesn't have any users for now and so no other part of the kernel will be impacted with this change. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-12-14OPP: Add dev_pm_opp_xlate_performance_state() helperViresh Kumar1-0/+63
dev_pm_genpd_set_performance_state() needs to handle performance state propagation going forward. Currently this routine only gets the required performance state of the device's genpd as an argument, but it doesn't know how to translate that to master genpd(s) of the device's genpd. Introduce a new helper dev_pm_opp_xlate_performance_state() which will be used to translate from performance state of a device (or genpd sub-domain) to another device (or master genpd). Normally the src_table (of genpd sub-domain) will have the "required_opps" property set to point to one of the OPPs in the dst_table (of master genpd), but in some cases the genpd and its master have one to one mapping of performance states and so none of them have the "required-opps" property set. Return the performance state of the src_table as it is in such cases. Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-12-14OPP: Improve _find_table_of_opp_np()Viresh Kumar1-4/+10
Make _find_table_of_opp_np() more efficient by using of_get_parent() to find the parent OPP table node. Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-12-11OPP: Fix missing debugfs supply directory for OPPsViresh Kumar3-9/+29
There is one case where we may end up with no "supply" directory for the OPPs in debugfs. That happens when the OPP core isn't managing the regulators for the device and the device's OPP do have microvolt property. It happens because the opp_table->regulator_count remains set to 0 and the debugfs routines don't add any supply directory in such a case. This commit fixes that by setting opp_table->regulator_count to 1 in that particular case. But to make everything work nicely and not break other parts of the core, regulator_count is defined as "int" now instead of "unsigned int" and it can have different special values now. It is set to -1 initially to mark it "uninitialized" and later only we set it to 0 or positive values after checking how many supplies are there. This also helps in finding the bugs where only few of the OPPs have the "opp-microvolt" property set and not all. Fixes: 1fae788ed640 ("PM / OPP: Don't create debugfs "supply-0" directory unnecessarily") Reported-by: Quentin Perret <quentin.perret@arm.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-12-11OPP: Use opp_table->regulators to verify no regulator caseViresh Kumar1-4/+7
The value of opp_table->regulator_count is not very consistent right now and it may end up being 0 while we do have a "opp-microvolt" property in the OPP table. It was kept that way as we used to check if any regulators are set with the OPP core for a device or not using value of regulator_count. Lets use opp_table->regulators for that purpose as the meaning of regulator_count is going to change in the later patches. Reported-by: Quentin Perret <quentin.perret@arm.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-23OPP: Fix parsing of multiple phandles in "operating-points-v2" propertyViresh Kumar1-4/+2
We currently return error if more than one phandle is present in the "operating-points-v2" property, which is incorrect. We only want to check the count of phandles here and set index to 0 if only one phandle is present. Fix it. Fixes: 5ed4cecd75e9 ("OPP: Pass OPP table to _of_add_opp_table_v{1|2}()") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-22opp: ti-opp-supply: Fix platform_no_drv_owner.cocci warningsYueHaibing1-1/+0
Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-13opp: ti-opp-supply: Correct the supply in _get_optimal_vdd_voltage callKeerthy1-1/+1
_get_optimal_vdd_voltage call provides new_supply_vbb->u_volt as the reference voltage while it should be really new_supply_vdd->u_volt. Cc: 4.16+ <stable@vger.kernel.org> # v4.16+ Fixes: 9a835fa6e47 ("PM / OPP: Add ti-opp-supply driver") Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-13opp: ti-opp-supply: Dynamically update u_volt_minKeerthy1-0/+3
The voltage range (min, max) provided in the device tree is from the data manual and is pretty big, catering to a wide range of devices. On a i2c read/write failure the regulator_set_voltage_triplet function falls back to set voltage between min and max. The min value from Device Tree can be lesser than the optimal value and in that case that can lead to a hang or crash. Hence set the u_volt_min dynamically to the optimal voltage value. Cc: 4.16+ <stable@vger.kernel.org> # v4.16+ Fixes: 9a835fa6e47 ("PM / OPP: Add ti-opp-supply driver") Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-05OPP: Remove of_dev_pm_opp_find_required_opp()Viresh Kumar1-54/+0
This isn't used anymore, remove it. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-05OPP: Rename and relocate of_genpd_opp_to_performance_state()Viresh Kumar1-0/+44
The OPP core already has the performance state values for each of the genpd's OPPs and there is no need to call the genpd callback again to get the performance state for the case where the end device doesn't have an OPP table and has the "required-opps" property directly in its node. This commit renames of_genpd_opp_to_performance_state() as of_get_required_opp_performance_state() and moves it to the OPP core, as it is all about OPP stuff now. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-05OPP: Configure all required OPPsViresh Kumar2-50/+68
Now that all the infrastructure is in place to support multiple required OPPs, lets switch over to using it. A new internal routine _set_required_opps() takes care of updating performance state for all the required OPPs. With this the performance state updates are supported even when the end device needs to configure regulators as well, that wasn't the case earlier. The pstates were earlier stored in the end device's OPP structures, that also changes now as those values are stored in the genpd's OPP structures. And so we switch over to using pm_genpd_opp_to_performance_state() instead of of_genpd_opp_to_performance_state() to get performance state for the genpd OPPs. The routine _generic_set_opp_domain() is not required anymore and is removed. On errors we don't try to recover by reverting to old settings as things are really complex now and the calls here should never really fail unless there is a bug. There is no point increasing the complexity, for code which will never be executed. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-05OPP: Add dev_pm_opp_{set|put}_genpd_virt_dev() helperViresh Kumar3-1/+107
Multiple generic power domains for a consumer device are supported with the help of virtual devices, which are created for each consumer device - genpd pair. These are the device structures which are attached to the power domain and are required by the OPP core to set the performance state of the genpd. The helpers added by this commit are required to be called once for each of these virtual devices. These are required only if multiple domains are available for a device, otherwise the actual device structure will be used instead by the OPP core. The new helpers also support the complex cases where the consumer device wouldn't always require all the domains. For example, a camera may require only one power domain during normal operations but two during high resolution operations. The consumer driver can call dev_pm_opp_put_genpd_virt_dev(high_resolution_genpd_virt_dev) if it is currently operating in the normal mode and doesn't have any performance requirements from the genpd which manages high resolution power requirements. The consumer driver can later call dev_pm_opp_set_genpd_virt_dev(high_resolution_genpd_virt_dev) once it switches back to the high resolution mode. The new helpers differ from other OPP set/put helpers as the new ones can be called with OPPs initialized for the table as we may need to call them on the fly because of the complex case explained above. For this reason it is possible that the genpd virt_dev structure may be used in parallel while the new helpers are running and a new mutex is added to protect against that. We didn't use the existing opp_table->lock mutex as that is widely used in the OPP core and we will need this lock in the dev_pm_opp_set_rate() helper while changing OPP and we need to make sure there is not much contention while doing that as that's the hotpath. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-05OPP: Populate OPPs from "required-opps" propertyViresh Kumar3-2/+86
An earlier commit populated the OPP tables from the "required-opps" property, this commit populates the individual OPPs. This is repeated for each OPP in the OPP table and these populated OPPs will be used by later commits. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-05OPP: Populate required opp tables from "required-opps" propertyViresh Kumar3-0/+157
The current implementation works only for the case where a single phandle is present in the "required-opps" property, while DT allows multiple phandles to be present there. This patch adds new infrastructure to parse all the phandles present in "required-opps" property and save pointers of the required OPP's OPP tables. These will be used by later commits. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-05OPP: Separate out custom OPP handler specific codeViresh Kumar1-27/+40
Create a separate routine to take care of custom set_opp() handler specific stuff. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-11-05OPP: Identify and mark genpd OPP tablesViresh Kumar2-2/+6
We need to handle genpd OPP tables differently, this is already the case at one location and will be extended going forward. Add another field to the OPP table to check if the table belongs to a genpd or not. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2018-10-04PM / OPP: _of_add_opp_table_v2(): increment count only if OPP is addedDave Gerlach1-13/+20
Currently the _of_add_opp_table_v2 call loops through the OPP nodes in the operating-points-v2 table in the device tree and calls _opp_add_static_v2 for each to add them to the table. It counts each iteration through this loop as an added OPP, however there are cases where _opp_add_static_v2() returns 0 but no new OPP is added to the list. This can happen while adding duplicate OPP or if the OPP isn't supported by hardware. Because of this the count variable will contain the number of OPP nodes in the table in device tree but not necessarily the ones that are actually added. As this count value is what is checked to determine if there are any valid OPPs, if a platform has an operating-points-v2 table with all OPP nodes containing opp-supported-hw values that are not currently supported, then _of_add_opp_table_v2 will fail to abort as it should due to an empty table. Additionally, since commit 3ba98324e81a ("PM / OPP: Get performance state using genpd helper"), the same count variable is compared against the number of OPPs containing performance states and requires that either all or none have pstates set, however in the case of any opp table that has any entries that do not get added by _opp_add_static_v2 due to incompatible opp-supported-hw fields, these numbers will not match and _of_add_opp_table_v2 will incorrectly fail. We need to clearly identify all the three cases (success, failure, unsupported/duplicate OPPs) and then increment count only on success case. Change return type of _opp_add_static_v2() to return the pointer to the newly added OPP instead of an integer. This routine now returns a valid pointer if the OPP is really added, NULL for unsupported or duplicate OPPs, and error value cased as a pointer on errors. Ideally the fixes tag in this commit should point back to the commit that introduced OPP v2 initially, as that's where we started incorrectly accounting for duplicate OPPs: commit 274659029c9d ("PM / OPP: Add support to parse "operating-points-v2" bindings") But it wasn't a real problem until recently as the count was only used to check if any OPPs are added or not. And so this commit points to a rather recent commit where we added more code that depends on the value of "count". Fixes: 3ba98324e81a ("PM / OPP: Get performance state using genpd helper") Reported-by: Dave Gerlach <d-gerlach@ti.com> Reported-by: Niklas Cassel <niklas.cassel@linaro.org> Tested-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>