summaryrefslogtreecommitdiffstats
path: root/drivers/nvmem
AgeCommit message (Collapse)AuthorFilesLines
2019-12-05Merge tag 'armsoc-drivers' of ↵Linus Torvalds1-3/+21
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Olof Johansson: "Various driver updates for platforms: - A larger set of work on Tegra 2/3 around memory controller and regulator features, some fuse cleanups, etc.. - MMP platform drivers, in particular for USB PHY, and other smaller additions. - Samsung Exynos 5422 driver for DMC (dynamic memory configuration), and ASV (adaptive voltage), allowing the platform to run at more optimal operating points. - Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas - Clock/reset control driver for TI/OMAP - Meson-A1 reset controller support - Qualcomm sdm845 and sda845 SoC IDs for socinfo" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits) firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT soc: fsl: add RCPM driver dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition memory: tegra: Consolidate registers definition into common header memory: tegra: Ensure timing control debug features are disabled memory: tegra: Introduce Tegra30 EMC driver memory: tegra: Do not handle error from wait_for_completion_timeout() memory: tegra: Increase handshake timeout on Tegra20 memory: tegra: Print a brief info message about EMC timings memory: tegra: Pre-configure debug register on Tegra20 memory: tegra: Include io.h instead of iopoll.h memory: tegra: Adapt for Tegra20 clock driver changes memory: tegra: Don't set EMC rate to maximum on probe for Tegra20 memory: tegra: Add gr2d and gr3d to DRM IOMMU group memory: tegra: Set DMA mask based on supported address bits soc: at91: Add Atmel SFR SN (Serial Number) support memory: atmel-ebi: switch to SPDX license identifiers memory: atmel-ebi: move NUM_CS definition inside EBI driver soc: mediatek: Refactor bus protection control soc: mediatek: Refactor sram control ...
2019-11-27Merge tag 'char-misc-5.5-rc1' of ↵Linus Torvalds7-18/+838
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big set of char/misc and other driver patches for 5.5-rc1 Loads of different things in here, this feels like the catch-all of driver subsystems these days. Full details are in the shortlog, but nothing major overall, just lots of driver updates and additions. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits) char: Fix Kconfig indentation, continued habanalabs: add more protection of device during reset habanalabs: flush EQ workers in hard reset habanalabs: make the reset code more consistent habanalabs: expose reset counters via existing INFO IOCTL habanalabs: make code more concise habanalabs: use defines for F/W files habanalabs: remove prints on successful device initialization habanalabs: remove unnecessary checks habanalabs: invalidate MMU cache only once habanalabs: skip VA block list update in reset flow habanalabs: optimize MMU unmap habanalabs: prevent read/write from/to the device during hard reset habanalabs: split MMU properties to PCI/DRAM habanalabs: re-factor MMU masks and documentation habanalabs: type specific MMU cache invalidation habanalabs: re-factor memory module code habanalabs: export uapi defines to user-space habanalabs: don't print error when queues are full habanalabs: increase max jobs number to 512 ...
2019-11-05nvmem: add Rockchip OTP driverFinley Xiao3-0/+281
Newer Rockchip socs like the px30 use a different one-time-programmable memory controller for things like cpu-id and leakage information, so add the necessary driver for it. Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com> [ported from vendor 4.4, converted to clock-bulk API and cleanups] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20191029114240.14905-11-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-05nvmem: imx: scu: fix dependency in KconfigSrinivas Kandagatla1-0/+1
Fix below error by adding HAVE_ARM_SMCCC dependency in Kconfig ERROR: "__arm_smccc_smc" [drivers/nvmem/nvmem-imx-ocotp-scu.ko] undefined! Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20191029114240.14905-9-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-05nvmem: sprd: Add Spreadtrum SoCs eFuse supportFreeman Liu3-0/+437
The Spreadtrum eFuse controller is widely used to dump chip ID, configuration setting, function select and so on, as well as supporting one-time programming. Signed-off-by: Freeman Liu <freeman.liu@unisoc.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20191029114240.14905-8-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-05nvmem: imx-ocotp: reset error status on probeLucas Stach1-0/+4
If software running before the OCOTP driver is loaded left the controller with the error status pending, the driver will never be able to complete the read timing setup. Reset the error status on probe to make sure the controller is in usable state. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20191029114240.14905-6-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-05nvmem: imx: scu: support writePeng Fan1-1/+72
The fuse programming from non-secure world is blocked, so we could only use Arm Trusted Firmware SIP call to let ATF program fuse. Because there is ECC region that could only be programmed once, so add a heler in_ecc to check the ecc region. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20191029114240.14905-5-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-05nvmem: imx: scu: support hole region checkPeng Fan1-5/+42
Introduce HOLE/ECC_REGION flag and in_hole helper to ease the check of hole region. The ECC_REGION is also introduced here which is preparing for programming support. ECC_REGION could only be programmed once, so need take care. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20191029114240.14905-4-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-11-05nvmem: sc27xx: Change to use devm_hwspin_lock_request_specific() to request ↵Baolin Wang1-12/+1
one hwlock Change to use devm_hwspin_lock_request_specific() to help to simplify the cleanup code for drivers requesting one hwlock. Thus we can remove the redundant sc27xx_efuse_remove() and platform_set_drvdata(). Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20191029114240.14905-3-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-10-07nvmem: core: add nvmem_device_findThomas Bogendoerfer1-34/+27
nvmem_device_find provides a way to search for nvmem devices with the help of a match function simlair to bus_find_device. Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Lee Jones <lee.jones@linaro.org> Cc: David S. Miller <davem@davemloft.net> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-doc@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-mips@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-rtc@vger.kernel.org Cc: linux-serial@vger.kernel.org
2019-10-03firmware: meson_sm: Rework driver as a proper platform driverCarlo Caione1-3/+21
The secure monitor driver is currently a frankenstein driver which is registered as a platform driver but its functionality goes through a global struct accessed by the consumer drivers using exported helper functions. Try to tidy up the driver moving the firmware struct into the driver data and make the consumer drivers referencing the secure-monitor using a new property in the DT. Currently only the nvmem driver is using this API so we can fix it in the same commit. Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Carlo Caione <ccaione@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-09-18Merge tag 'char-misc-5.4-rc1' of ↵Linus Torvalds5-2/+18
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big char/misc driver pull request for 5.4-rc1. As has been happening in previous releases, more and more individual driver subsystem trees are ending up in here. Now if that is good or bad I can't tell, but hopefully it makes your life easier as it's more of an aggregation of trees together to one merge point for you. Anyway, lots of stuff in here: - habanalabs driver updates - thunderbolt driver updates - misc driver updates - coresight and intel_th hwtracing driver updates - fpga driver updates - extcon driver updates - some dma driver updates - char driver updates - android binder driver updates - nvmem driver updates - phy driver updates - parport driver fixes - pcmcia driver fix - uio driver updates - w1 driver updates - configfs fixes - other assorted driver updates All of these have been in linux-next for a long time with no reported issues" * tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (200 commits) misc: mic: Use PTR_ERR_OR_ZERO rather than its implementation habanalabs: correctly cast variable to __le32 habanalabs: show correct id in error print habanalabs: stop using the acronym KMD habanalabs: display card name as sensors header habanalabs: add uapi to retrieve aggregate H/W events habanalabs: add uapi to retrieve device utilization habanalabs: Make the Coresight timestamp perpetual habanalabs: explicitly set the queue-id enumerated numbers habanalabs: print to kernel log when reset is finished habanalabs: replace __le32_to_cpu with le32_to_cpu habanalabs: replace __cpu_to_le32/64 with cpu_to_le32/64 habanalabs: Handle HW_IP_INFO if device disabled or in reset habanalabs: Expose devices after initialization is done habanalabs: improve security in Debug IOCTL habanalabs: use default structure for user input in Debug IOCTL habanalabs: Add descriptive name to PSOC app status register habanalabs: Add descriptive names to PSOC scratch-pad registers habanalabs: create two char devices per ASIC habanalabs: change device_setup_cdev() to be more generic ...
2019-09-17Merge tag 'leds-for-5.4-rc1' of ↵Linus Torvalds1-6/+1
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds Pull LED updates from Jacek Anaszewski: "In this cycle we've finally managed to contribute the patch set sorting out LED naming issues. Besides that there are many changes scattered among various LED class drivers and triggers. LED naming related improvements: - add new 'function' and 'color' fwnode properties and deprecate 'label' property which has been frequently abused for conveying vendor specific names that have been available in sysfs anyway - introduce a set of standard LED_FUNCTION* definitions - introduce a set of standard LED_COLOR_ID* definitions - add a new {devm_}led_classdev_register_ext() API with the capability of automatic LED name composition basing on the properties available in the passed fwnode; the function is backwards compatible in a sense that it uses 'label' data, if present in the fwnode, for creating LED name - add tools/leds/get_led_device_info.sh script for retrieving LED vendor, product and bus names, if applicable; it also performs basic validation of an LED name - update following drivers and their DT bindings to use the new LED registration API: - leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114, leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt Other LED class improvements: - replace {devm_}led_classdev_register() macros with inlines - allow to call led_classdev_unregister() unconditionally - switch to use fwnode instead of be stuck with OF one LED triggers improvements: - led-triggers: - fix dereferencing of null pointer - fix a memory leak bug - ledtrig-gpio: - GPIO 0 is valid Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer, more complete driver exists, based on a generic driver for the AMD SOCs gpio-controller, supporting LEDs as well other devices: - drop profile field from priv data - drop iosize field from priv data - drop enum_apu_led_platform_types - drop superseeded apu2/3 led support - add pr_fmt prefix for better log output - fix error message on probing failure Other misc fixes and improvements to existing LED class drivers: - leds-ns2, leds-max77650: - add of_node_put() before return - leds-pwm, leds-is31fl32xx: - use struct_size() helper - leds-lm3697, leds-lm36274, leds-lm3532: - switch to use fwnode_property_count_uXX() - leds-lm3532: - fix brightness control for i2c mode - change the define for the fs current register - fixes for the driver for stability - add full scale current configuration - dt: Add property for full scale current. - avoid potentially unpaired regulator calls - move static keyword to the front of declarations - fix optional led-max-microamp prop error handling - leds-max77650: - add of_node_put() before return - add MODULE_ALIAS() - Switch to fwnode property API - leds-as3645a: - fix misuse of strlcpy - leds-netxbig: - add of_node_put() in netxbig_leds_get_of_pdata() - remove legacy board-file support - leds-is31fl319x: - simplify getting the adapter of a client - leds-ti-lmu-common: - fix coccinelle issue - move static keyword to the front of declaration - leds-syscon: - use resource managed variant of device register - leds-ktd2692: - fix a typo in the name of a constant - leds-lp5562: - allow firmware files up to the maximum length - leds-an30259a: - fix typo - leds-pca953x: - include the right header" * tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits) leds: lm3532: Fix optional led-max-microamp prop error handling led: triggers: Fix dereferencing of null pointer leds: ti-lmu-common: Move static keyword to the front of declaration leds: lm3532: Move static keyword to the front of declarations leds: trigger: gpio: GPIO 0 is valid leds: pwm: Use struct_size() helper leds: is31fl32xx: Use struct_size() helper leds: ti-lmu-common: Fix coccinelle issue in TI LMU leds: lm3532: Avoid potentially unpaired regulator calls leds: syscon: Use resource managed variant of device register leds: Replace {devm_}led_classdev_register() macros with inlines leds: Allow to call led_classdev_unregister() unconditionally leds: lm3532: Add full scale current configuration dt: lm3532: Add property for full scale current. leds: lm3532: Fixes for the driver for stability leds: lm3532: Change the define for the fs current register leds: lm3532: Fix brightness control for i2c mode leds: Switch to use fwnode instead of be stuck with OF one leds: max77650: Switch to fwnode property API led: triggers: Fix a memory leak bug ...
2019-08-18nvmem: imx: add i.MX8QM platform supportFugang Duan1-0/+7
i.MX8QM efuse table has some difference with i.MX8QXP platform, so add i.MX8QM platform support. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20190818093345.29647-8-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-18nvmem: mxs-ocotp: update MODULE_AUTHOR() email addressStefan Wahren1-1/+1
The email address listed in MODULE_AUTHOR() will be disabled in the near future. Replace it with my private one. Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20190818093345.29647-6-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-18nvmem: meson-mx-efuse: allow reading data smaller than word_sizeMartin Blumenstingl1-1/+2
Some Amlogic boards store the Ethernet MAC address inside the eFuse. The Ethernet MAC address uses 6 bytes. The existing logic in meson_mx_efuse_read() would write beyond the end of the data buffer when trying to read data with a size that is not aligned to word_size (4 bytes on Meson8, Meson8b and Meson8m2). Calculate the remaining data to copy inside meson_mx_efuse_read() so reading 6 bytes doesn't write beyond the end of the data buffer. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20190818093345.29647-5-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-18nvmem: sunxi_sid: fix A64 SID controller supportStefan Mavrodiev1-0/+1
Like in H3, A64 SID controller doesn't return correct data when using direct access. It appears that on A64, SID needs 8 bytes of word_size. Workaround is to enable read by registers. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20190818093345.29647-4-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-08-18nvmem: imx-ocotp: Add i.MX8MN supportAnson Huang1-0/+7
i.MX8MN is a new SoC of i.MX8M series, it is similar to i.MX8MM in terms of addressing and clock setup, add support for its fuse read/write. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20190818093345.29647-3-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-30nvmem: Use the same permissions for eeprom as for nvmemJean Delvare1-4/+11
The compatibility "eeprom" attribute is currently root-only no matter what the configuration says. The "nvmem" attribute does respect the setting of the root_only configuration bit, so do the same for "eeprom". Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: b6c217ab9be6 ("nvmem: Add backwards compatibility support for older EEPROM drivers.") Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20190728184255.563332e6@endymion Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-30drivers: Introduce device lookup variants by of_nodeSuzuki K Poulose1-6/+1
Introduce wrappers for {bus/driver/class}_find_device() to locate devices by its of_node. Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: dri-devel@lists.freedesktop.org Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: devicetree@vger.kernel.org Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: linux-i2c@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Cc: linux-spi@vger.kernel.org Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Takashi Iwai <tiwai@suse.com> Cc: Alan Tull <atull@kernel.org> Cc: linux-fpga@vger.kernel.org Cc: Peter Rosin <peda@axentia.se> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Thor Thayer <thor.thayer@linux.intel.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Peter Rosin <peda@axentia.se> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> # I2C part Acked-by: Moritz Fischer <mdf@kernel.org> # For FPGA part Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20190723221838.12024-3-suzuki.poulose@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-12Merge tag 'driver-core-5.3-rc1' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core and debugfs updates from Greg KH: "Here is the "big" driver core and debugfs changes for 5.3-rc1 It's a lot of different patches, all across the tree due to some api changes and lots of debugfs cleanups. Other than the debugfs cleanups, in this set of changes we have: - bus iteration function cleanups - scripts/get_abi.pl tool to display and parse Documentation/ABI entries in a simple way - cleanups to Documenatation/ABI/ entries to make them parse easier due to typos and other minor things - default_attrs use for some ktype users - driver model documentation file conversions to .rst - compressed firmware file loading - deferred probe fixes All of these have been in linux-next for a while, with a bunch of merge issues that Stephen has been patient with me for" * tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits) debugfs: make error message a bit more verbose orangefs: fix build warning from debugfs cleanup patch ubifs: fix build warning after debugfs cleanup patch driver: core: Allow subsystems to continue deferring probe drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT arch_topology: Remove error messages on out-of-memory conditions lib: notifier-error-inject: no need to check return value of debugfs_create functions swiotlb: no need to check return value of debugfs_create functions ceph: no need to check return value of debugfs_create functions sunrpc: no need to check return value of debugfs_create functions ubifs: no need to check return value of debugfs_create functions orangefs: no need to check return value of debugfs_create functions nfsd: no need to check return value of debugfs_create functions lib: 842: no need to check return value of debugfs_create functions debugfs: provide pr_fmt() macro debugfs: log errors when something goes wrong drivers: s390/cio: Fix compilation warning about const qualifiers drivers: Add generic helper to match by of_node driver_find_device: Unify the match function with class_find_device() bus_find_device: Unify the match callback with class_find_device ...
2019-06-26nvmem: imx-ocotp: imx8mq is compatible with imx6 not imx7Leonard Crestez1-2/+2
According to NXP Reference Manuals and uboot/atf sources the OCOTP block on imx8m behaves more like imx6 than imx7. - Fuses can be read/written 32bits at a time (no imx7-like banking) - The OCOTP_HW_OCOTP_TIMING register is like imx6 not imx7 Since nvmem doesn't support uboot-style "sense" and "override" this issue only affected "write" which is very rarely used. Fixes: 163c0dbd0cb1 ("nvmem: imx-ocotp: add support for imx8mq") Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-26nvmem: imx-ocotp: Add i.MX8MM supportBryan O'Donoghue1-0/+7
This patch adds support to burn the fuses on the i.MX8MM. https://www.nxp.com/webapp/Download?colCode=IMX8MMRM The i.MX8MM is similar to i.MX6 processors in terms of addressing and clock setup. The documentation specifies 60 discreet OTP registers but, the fusemap address space encompasses up to 256 registers. We map the entire putative 256 OTP registers. Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-26nvmem: imx-ocotp: Change TIMING calculation to u-boot algorithmBryan O'Donoghue1-4/+32
The RELAX field of the OCOTP block is turning out as a zero on i.MX8MM. This messes up the subsequent re-load of the fuse shadow registers. After some discussion with people @ NXP its clear we have missed a trick here in Linux. The OCOTP fuse programming time has a physical minimum 'burn time' that is not related to the ipg_clk. We need to define the RELAX, STROBE_READ and STROBE_PROG fields in terms of desired timings to allow for the burn-in to safely complete. Right now only the RELAX field is calculated in terms of an absolute time and we are ending up with a value of zero. This patch inherits the u-boot timings for the OCOTP_TIMING calculation on the i.MX6 and i.MX8. Those timings are known to work and critically specify values such as STROBE_PROG as a minimum timing. Fixes: 0642bac7da42 ("nvmem: imx-ocotp: add write support") Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Suggested-by: Leonard Crestez <leonard.crestez@nxp.com> Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-26nvmem: imx-ocotp: Ensure WAIT bits are preserved when setting timingBryan O'Donoghue1-1/+2
The i.MX6 and i.MX8 both have a bit-field spanning bits 27:22 called the WAIT field. The WAIT field according to the documentation for both parts "specifies time interval between auto read and write access in one time program. It is given in number of ipg_clk periods." This patch ensures that the relevant field is read and written back to the timing register. Fixes: 0642bac7da42 ("nvmem: imx-ocotp: add write support") Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-26nvmem: imx-ocotp: Elongate OCOTP_CTRL ADDR field to eight bitsBryan O'Donoghue1-1/+1
i.MX6 defines OCOTP_CTRLn:ADDR as seven bit address-field with a one bit RSVD0 field, i.MX7 defines OCOTP_CTRLn:ADDR as a four bit address-field with a four bit RSVD0 field. i.MX8 defines the OCOTP_CTRLn:ADDR bit-field as a full range eight bits. i.MX6 and i.MX7 should return zero for their respective RSVD0 bits and ignore a write-back of zero where i.MX8 will make use of the full range. This patch expands the bit-field definition for all users to eight bits, which is safe due to RSVD0 being a no-op for the i.MX6 and i.MX7. Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-24bus_find_device: Unify the match callback with class_find_deviceSuzuki K Poulose1-1/+1
There is an arbitrary difference between the prototypes of bus_find_device() and class_find_device() preventing their callers from passing the same pair of data and match() arguments to both of them, which is the const qualifier used in the prototype of class_find_device(). If that qualifier is also used in the bus_find_device() prototype, it will be possible to pass the same match() callback function to both bus_find_device() and class_find_device(), which will allow some optimizations to be made in order to avoid code duplication going forward. Also with that, constify the "data" parameter as it is passed as a const to the match function. For this reason, change the prototype of bus_find_device() to match the prototype of class_find_device() and adjust its callers to use the const qualifier in accordance with the new prototype of it. Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Andreas Noever <andreas.noever@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Corey Minyard <minyard@acm.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: David Kershner <david.kershner@unisys.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: David Airlie <airlied@linux.ie> Cc: Felipe Balbi <balbi@kernel.org> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Harald Freudenberger <freude@linux.ibm.com> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jonathan Cameron <jic23@kernel.org> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: Len Brown <lenb@kernel.org> Cc: Mark Brown <broonie@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michael Jamet <michael.jamet@intel.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Peter Oberparleiter <oberpar@linux.ibm.com> Cc: Sebastian Ott <sebott@linux.ibm.com> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Yehezkel Bernat <YehezkelShB@gmail.com> Cc: rafael@kernel.org Acked-by: Corey Minyard <minyard@acm.org> Acked-by: David Kershner <david.kershner@unisys.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-23Merge 5.2-rc6 into char-misc-nextGreg Kroah-Hartman5-26/+5
We need the char-misc fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19nvmem: Broaden the selection of NVMEM_SNVS_LPGPRFabio Estevam1-1/+1
The SNVS LPGR IP block is also found on other i.MX SoCs that are not covered by the current SOC_IMX6 || SOC_IMX7D logic. One example is the i.MX7ULP. To avoid keep expanding the SoC logic selection, make it broader by using the more generic ARCH_MXC symbol instead. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19nvmem: imx: add i.MX8 nvmem driverPeng Fan3-0/+170
This patch adds i.MX8 nvmem ocotp driver to access fuse via RPC to i.MX8 system controller. Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner3-12/+3
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 460Thomas Gleixner2-14/+2
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation http www opensource org licenses gpl license html http www gnu org copyleft gpl html extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 3 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081201.897982733@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 295Thomas Gleixner3-27/+3
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of version 2 of the gnu general public license as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 64 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexios Zavras <alexios.zavras@intel.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190529141901.894819585@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 284Thomas Gleixner2-18/+2
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 and only version 2 as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 294 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Alexios Zavras <alexios.zavras@intel.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174Thomas Gleixner2-18/+2
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 655 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Richard Fontana <rfontana@redhat.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157Thomas Gleixner1-11/+1
Based on 3 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [graeme] [gregory] [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema] [hk] [hemahk]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1105 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner1-0/+1
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-16Merge tag 'armsoc-drivers' of ↵Linus Torvalds1-3/+7
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC-related driver updates from Olof Johansson: "Various driver updates for platforms and a couple of the small driver subsystems we merge through our tree: Among the larger pieces: - Power management improvements for TI am335x and am437x (RTC suspend/wake) - Misc new additions for Amlogic (socinfo updates) - ZynqMP FPGA manager - Nvidia improvements for reset/powergate handling - PMIC wrapper for Mediatek MT8516 - Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits) soc: aspeed: fix Kconfig soc: add aspeed folder and misc drivers spi: zynqmp: Fix build break soc: imx: Add generic i.MX8 SoC driver MAINTAINERS: Update email for Qualcomm SoC maintainer memory: tegra: Fix a typos for "fdcdwr2" mc client Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+" memory: tegra: Replace readl-writel with mc_readl-mc_writel memory: tegra: Fix integer overflow on tick value calculation memory: tegra: Fix missed registers values latching ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30 optee: allow to work without static shared memory soc/tegra: pmc: Move powergate initialisation to probe soc/tegra: pmc: Remove reset sysfs entries on error soc/tegra: pmc: Fix reset sources and levels soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask fpga manager: Adding FPGA Manager support for Xilinx zynqmp dt-bindings: fpga: Add bindings for ZynqMP fpga driver firmware: xilinx: Add fpga API's ...
2019-04-25nvmem: core: add NVMEM_SYSFS KconfigSrinivas Kandagatla5-260/+335
Many nvmem providers are not very keen on having default sysfs nvmem entry, as most of the usecases for them are inside kernel itself. And in some cases read/writes to some areas in nvmem are restricted and trapped at secure monitor level, so accessing them from userspace would result in board reboots. This patch adds new NVMEM_SYSFS Kconfig to make binary sysfs entry an optional one. This provision will give more flexibility to users. This patch also moves existing sysfs code to a new file so that its not compiled in when its not really required. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Gaurav Kohli <gkohli@codeaurora.org> Tested-by: Gaurav Kohli <gkohli@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: sunxi_sid: Support SID on H6Yangtao Li1-0/+6
Add support for H6's SID controller. It supports 4K-bit EFUSE, bigger than before. Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: sunxi-sid: convert to SPDX license tagsYangtao Li1-10/+1
Updates license to use SPDX-License-Identifier. Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: imx-iim: use devm_platform_ioremap_resource() to simplify codeAnson Huang1-3/+1
Use the new helper devm_platform_ioremap_resource() which wraps the platform_get_resource() and devm_ioremap_resource() together, to simplify the code. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: mxs-ocotp: use devm_platform_ioremap_resource() to simplify codeAnson Huang1-3/+1
Use the new helper devm_platform_ioremap_resource() which wraps the platform_get_resource() and devm_ioremap_resource() together, to simplify the code. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: imx-ocotp: use devm_platform_ioremap_resource() to simplify codeAnson Huang1-3/+1
Use the new helper devm_platform_ioremap_resource() which wraps the platform_get_resource() and devm_ioremap_resource() together, to simplify the code. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: core: fix read buffer in placeJorge Ramirez-Ortiz1-5/+10
When the bit_offset in the cell is zero, the pointer to the msb will not be properly initialized (ie, will still be pointing to the first byte in the buffer). This being the case, if there are bits to clear in the msb, those will be left untouched while the mask will incorrectly clear bit positions on the first byte. This commit also makes sure that any byte unused in the cell is cleared. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: core: add nvmem_cell_read_u16Fabrice Gasnier1-0/+37
Add nvmem_cell_read_u16() helper to ease read of an u16 value on consumer side. This is inspired by nvmem_cell_read_u32() function. This helper is useful on stm32 that has 16 bits data cells stored in non volatile memory. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: stm32: add support for STM32MP15 BSEC to control OTP dataFabrice Gasnier1-5/+129
On STM32MP15, OTP area may be read/written by using BSEC (boot, security and OTP control). BSEC registers set is composed of various regions, among which control registers and OTP shadow registers. Secure monitor calls are involved in this process to allow (or deny) access to the full range of OTP data. This adds support for reading and writing OTP data using SMC services. Data content can be aligned on 16-bits or 8-bits. Then take care of it, since BSEC data is 32-bits wide. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: Add driver for STM32 factory-programmed read only memFabrice Gasnier3-0/+90
Add a read only nvmem driver for STM32 factory-programmed memory area (on-chip non-volatile storage). Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: sunxi_sid: Support SID on A83T and H5Chen-Yu Tsai1-0/+2
The device tree binding already lists compatible strings for these two SoCs. They don't have the defect as seen on the H3, and the size and register layout is the same as the A64. Furthermore, the driver does not include nvmem cell definitions. Add support for these two compatible strings, re-using the config for the A64. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25nvmem: sunxi_sid: Read out data in native formatChen-Yu Tsai1-22/+1
Originally the SID e-fuses were thought to be in big-endian format. Later sources show that they are in fact native or little-endian. The most compelling evidence is the thermal sensor calibration data, which is a set of one to three 16-bit values. In native-endian they are in 16-bit cells with increasing offsets, whereas with big-endian they are in the wrong order, and a gap with no data will show if there are one or three cells. Switch to a native endian representation for the nvmem device. For the H3, the register read-out method was already returning data in native endian. This only affects the other SoCs. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>