Age | Commit message (Collapse) | Author | Files | Lines |
|
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We need to verify that the controller supports the security
commands before actually trying to issue them.
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
[hch: moved the check so that we don't call into the OPAL code if not
supported]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Insted of bloating the containing structure with it all the time this
allocates struct opal_dev dynamically. Additionally this allows moving
the definition of struct opal_dev into sed-opal.c. For this a new
private data field is added to it that is passed to the send/receive
callback. After that a lot of internals can be made private as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Scott Bauer <scott.bauer@intel.com>
Reviewed-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
When CONFIG_KASAN is enabled, compilation fails:
block/sed-opal.c: In function 'sed_ioctl':
block/sed-opal.c:2447:1: error: the frame size of 2256 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Moved all the ioctl structures off the stack and dynamically allocate
using _IOC_SIZE()
Fixes: 455a7b238cd6 ("block: Add Sed-opal library")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
NVMe supports up to 256 ranges per DSM command, so wire up support
for ranged discards up to that limit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This patch implements the necessary logic to unlock an Opal
enabled device coming back from an S3.
The patch also implements the SED/Opal allocation necessary to support
the opal ioctls.
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Instead of keeping two levels of indirection for requests types, fold it
all into the operations. The little caveat here is that previously
cmd_type only applied to struct request, while the request and bio op
fields were set to plain REQ_OP_READ/WRITE even for passthrough
operations.
Instead this patch adds new REQ_OP_* for SCSI passthrough and driver
private requests, althought it has to add two for each so that we
can communicate the data in/out nature of the request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This can be used to check for fs vs non-fs requests and basically
removes all knowledge of BLOCK_PC specific from the block layer,
as well as preparing for removing the cmd_type field in struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This patch sets the aborted flag only if an abort was sent, reducing
excessive kernel message spamming for completed IO that wasn't actually
aborted.
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
When the lightnvm core had the "gennvm" layer between the device and the
target, there was a need for the core to be able to figure out which
target it should send an end_io callback to. Leading to a "double"
end_io, first for the media manager instance, and then for the target
instance. Now that core and gennvm is merged, there is no longer a need
for this, and a single end_io callback will do.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Enable user-space to issue vector I/O commands through ioctls. To issue
a vector I/O, the ppa list with addresses is also required and must be
mapped for the controller to access.
For each ioctl, the result and status bits are returned as well, such
that user-space can retrieve the open-channel SSD completion bits.
The implementation covers the traditional use-cases of bad block
management, and vectored read/write/erase.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Metadata implementation, test, and fixes.
Signed-off-by: Simon A.F. Lund <slund@cnexlabs.com>
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The number of configuration groups has been limited to one in current
code, even if there is support for up to four. With the introduction
of the open-channel SSD 1.3 specification, only a single
group is exposed onwards. Reflect this in the nvm_id structure.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
For the first iteration of Open-Channel SSDs, it was anticipated that
there could be various media managers on top of an open-channel SSD,
such to allow vendors to plug in their own host-side FTLs, without the
media manager in between.
Now that an Open-Channel SSD is exposed as a traditional block device,
there is no longer a need for this. Therefore lets merge the gennvm code
with core and simplify the stack.
Signed-off-by: Matias Bjørling <matias@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The NVMe SCSI emulation doesn't use BLOCK_PC requests, so BLK_MAX_CDB
doesn't have a meaning for it. Instead opencode the value of 16
and refactor the code a bit so that related checks are next to each
other and we only need to use the value in one place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Since we moved the cdb parts and define out of the block proper,
we need to include scsi/scsi_request.h for the nvme scsi layer.
Fixes: 82ed4db499b8 ("block: split scsi_request out of struct request")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Without this deallocate won't work properly due to the mismatch
of the bio/request size and the actual payload size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
This patch performs dma sync operations on nvme_command
and nvme_completion.
nvme_command is synced
(a) on receiving of the recv queue completion for cpu access.
(b) before posting recv wqe back to rdma adapter for device access.
nvme_completion is synced
(a) on receiving of the recv queue completion of associated
nvme_command for cpu access.
(b) before posting send wqe to rdma adapter for device access.
This patch is generated for git://git.infradead.org/nvme-fabrics.git
Branch: nvmf-4.10
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
|
|
We only need to call delete_ctrl once, so given that both
keep-alive timeout and any other fatal error can trigger it,
just make sure we only call delete_ctrl once.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Make sure they are not running and we can free the controller
safely.
Signed-off-by: Roy Shterman <roys@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
No reason for them to be kept around if we are
deleting the subsystem, so instead of passively
wait for the host to disconnect, actively delete
the controllers.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Correct logic in disconnect queue LS handling.
Rework so that queue searching and error reporting is above the
section to send back a ls rjt
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Add Kconfig entries to manage what devices get assigned an MQ
scheduler, and add a blk-mq flag for drivers to opt out of scheduling.
The latter is useful for admin type queues that still allocate a blk-mq
queue and tag set, but aren't use for normal IO.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
|
|
The new blk_rq_payload_bytes generalizes the payload length hacks
that nvme_map_len did before.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Commit 54adc01055b7 ("nvme/quirk: Add a delay before checking for adapter
readiness") introduced a quirk to adapters that cannot read the bit
NVME_CSTS_RDY right after register NVME_REG_CC is set; these adapters
need a delay or else the action of reading the bit NVME_CSTS_RDY could
somehow corrupt adapter's registers state and it never recovers.
When this quirk was added, we checked ctrl->tagset in order to avoid
quirking in probe time, supposing we would never require such delay
during probe. Well, it was too optimistic; we in fact need this quirk
at probe time in some cases, like after a kexec.
In some experiments, after abnormal shutdown of machine (aka power cord
unplug), we booted into our bootloader in Power, which is a Linux kernel,
and kexec'ed into another distro. If this kexec is too quick, we end up
reaching the probe of NVMe adapter in that distro when adapter is in
bad state (not fully initialized on our bootloader). What happens next
is that nvme_wait_ready() is unable to complete, except if the quirk is
enabled.
So, this patch removes the original ctrl->tagset verification in order
to enable the quirk even on probe time.
Fixes: 54adc01055b7 ("nvme/quirk: Add a delay before checking for adapter readiness")
Reported-by: Andrew Byrne <byrneadw@ie.ibm.com>
Reported-by: Jaime A. H. Gomez <jahgomez@mx1.ibm.com>
Reported-by: Zachary D. Myers <zdmyers@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jeffrey Lien <Jeff.Lien@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Now that we don't abuse the cmd field in struct request for nvme command
passthrough this function needs to be converted to the proper accessor
as well.
Fixes: d49187e97e ("nvme: introduce struct nvme_request")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
|
|
Christoph writes:
The most significant one is that we've agreed on shared maintaince and
a common repository for the PCIe NVMe driver and NVMe over Fabrics. The
target code still only has a subset of the maintainers but goes through
the same tree as well. Keith, Sagi and me will take turns at collecting
patches and sending you pull requests.
|
|
The check to see if ret is non-zero and return this rather than count
is redundant in two occassions. It is redundant because prior to this
check, the return code ret is already checked for a non-zero error
return value and we return from the function at that point.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The Set Features implementation for Keep Alive Timer was using the wrong
structure when retrieving the KATO value; it was treating the Set
Features command as a Property Set command.
The NVMe spec defines the Keep Alive Timer feature as having one input
in CDW11 (4 bytes at offset 44 in the command) whereas the code was
reading 8 bytes at offset 48.
Since the Linux NVMe over Fabrics host never sets this feature, this
code has presumably never been tested.
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Simplify the error handling of nvme_fc_create_hw_io_queues(), this saves us
one variable and one level of indentation.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviwed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Dan Carpenters's tool caught a pointer reference - should have been
just ptr, not &ptr.
Don't bother. Remove the pointer value in the printf. Its irrelevant.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Now that the broken power state control is gone, it appears to serve
no purpose. Just delete it. NVME devices don't have a concept of
started vs stopped anyway.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
It is not theoretically possible for this driver to wrap twice while
processing completions. The driver allocates only 'queue_depth - 1'
tags, so there can never be more than that to reap when processing a
completion queue. Removing this misleading comment makes it a little
less likely people with broken controllers will blame the driver for
their spurious interrupts.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Convert to tabs and remove unneeded whitespaces.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Some OEMs believe they own the Identify Controller vendor specific
region and will repurpose it with their own values. While not common,
we can't rely on the PCI VID:DID to tell use how to decode the field
we reserved for this as the stripe size so we need to do something else
for the list of devices using this quirk.
The field was supposed to allow flexibility on the device's back-end
striping, but it turned out that never materialized; the chunk is always
the same as MDTS in the products subscribing to this quirk, so this
patch removes the stripe_size field and sets the chunk to the max hw
transfer size for the devices using this quirk.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Make sure we are using the correct scnprintf in the sysfs show
function for the CMB.
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by Jon Derrick: <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is the complete update for the rdma stack for this release cycle.
Most of it is typical driver and core updates, but there is the
entirely new VMWare pvrdma driver. You may have noticed that there
were changes in DaveM's pull request to the bnxt Ethernet driver to
support a RoCE RDMA driver. The bnxt_re driver was tentatively set to
be pulled in this release cycle, but it simply wasn't ready in time
and was dropped (a few review comments still to address, and some
multi-arch build issues like prefetch() not working across all
arches).
Summary:
- shared mlx5 updates with net stack (will drop out on merge if
Dave's tree has already been merged)
- driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- debug cleanups
- new connection rejection helpers
- SRP updates
- various misc fixes
- new paravirt driver from vmware"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (210 commits)
IB: Add vmw_pvrdma driver
IB/mlx4: fix improper return value
IB/ocrdma: fix bad initialization
infiniband: nes: return value of skb_linearize should be handled
MAINTAINERS: Update Intel RDMA RNIC driver maintainers
MAINTAINERS: Remove Mitesh Ahuja from emulex maintainers
IB/core: fix unmap_sg argument
qede: fix general protection fault may occur on probe
IB/mthca: Replace pci_pool_alloc by pci_pool_zalloc
mlx5, calc_sq_size(): Make a debug message more informative
mlx5: Remove a set-but-not-used variable
mlx5: Use { } instead of { 0 } to init struct
IB/srp: Make writing the add_target sysfs attr interruptible
IB/srp: Make mapping failures easier to debug
IB/srp: Make login failures easier to debug
IB/srp: Introduce a local variable in srp_add_one()
IB/srp: Fix CONFIG_DYNAMIC_DEBUG=n build
IB/multicast: Check ib_find_pkey() return value
IPoIB: Avoid reading an uninitialized member variable
IB/mad: Fix an array index check
...
|
|
Pull block IO fixes from Jens Axboe:
"A few fixes that I collected as post-merge.
I was going to wait a bit with sending this out, but the O_DIRECT fix
should really go in sooner rather than later"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: Fix failed allocation path when mapping queues
blk-mq: Avoid memory reclaim when remapping queues
block_dev: don't update file access position for sync direct IO
nvme/pci: Log PCI_STATUS when the controller dies
block_dev: don't test bdev->bd_contains when it is not stable
|
|
Pull configfs update from Christoph Hellwig:
"Just one simple change from Andrzej to drop the pointless return value
from the ->drop_link method"
* tag 'configfs-for-4.10' of git://git.infradead.org/users/hch/configfs:
fs: configfs: don't return anything from drop_link
|
|
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Also add nvme cm status strings and use them.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When debugging nvme controller crashes, it's nice to know whether
the controller died cleanly so that the failure is just reflected in
CSTS, it died and put an error in PCI_STATUS, or whether it died so
badly that it stopped responding to PCI configuration space reads.
I've seen a failure that gives 0xffff in PCI_STATUS on a Samsung
"SM951 NVMe SAMSUNG 256GB" with firmware "BXW75D0Q".
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Fixed up white space and hunk reject.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This reverts commit 6d31e3ba232ea22458b2f36b6d3f2f9f11bf3fa4.
This causes bootup problems for me both on my laptop and my desktop.
What they have in common is that they have NVMe disks with dm-crypt, but
it's not the same controller, so it's not controller-specific.
Jens does not see it on his machine (also NVMe), so it's presumably
something that triggers just on bootup. Possibly related to dm-crypt
and the fact that I mark my luks volume with "allow-discards" in
/etc/crypttab.
It's 100% repeatable for me, which made it fairly straightforward to
bisect the problem to this commit. Small mercies.
So we don't know what the reason is yet, but the revert is needed to get
things going again.
Acked-by: Jens Axboe <axboe@fb.com>
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
- Adam added opt-in ATA command priority support.
- There are machines which hide multiple nvme devices behind an ahci
BAR. Dan Williams proposed a solution to force-switch the mode but
deemed too hackishd. People are gonna discuss the proper way to
handle the situation in nvme standard meetings. For now, detect and
warn about the situation.
- Low level driver specific changes.
Christoph Hellwig pipes in about the hidden nvme warning:
"I wish that was the case. We've pretty much agreed that we'll want to
implement it as a virtual PCIe root bridge, similar to Intels other
'innovation' VMD that we work around that way.
But Intel management has apparently decided that they don't want to
spend more cycles on this now that Lenovo has an optional BIOS that
doesn't force this broken mode anymore, and no one outside of Intel
has enough information to implement something like this.
So for now I guess this warning is it, until Intel reconsideres and
spends resources on fixing up the damage their Chipset people caused"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: warn about remapped NVMe devices
ahci-remap.h: add ahci remapping definitions
nvme: move NVMe class code to pci_ids.h
pata: imx: support controller modes up to PIO4
pata: imx: add support of setting timings for PIO modes
pata: imx: set controller PIO mode with .set_piomode callback
pata: imx: sort headers out
ata: set ncq_prio_enabled iff device has support
ata: ATA Command Priority Disabled By Default
ata: Enabling ATA Command Priorities
block: Add iocontext priority to request
ahci: qoriq: added ls1046a platform support
|
|
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
|
|
Instead of allocating a single unused biovec for discard requests, send
them down without any payload. Instead we allow the driver to add a
"special" payload using a biovec embedded into struct request (unioned
over other fields never used while in the driver), and overloading
the number of segments for this case.
This has a couple of advantages:
- we don't have to allocate the bio_vec
- the amount of special casing for discard requests in the block
layer is significantly reduced
- using this same scheme for other request types is trivial,
which will be important for implementing the new WRITE_ZEROES
op on devices where it actually requires a payload (e.g. SCSI)
- we can get rid of playing games with the request length, as
we'll never touch it and completions will work just fine
- it will allow us to support ranged discard operations in the
future by merging non-contiguous discard bios into a single
request
- last but not least it removes a lot of code
This patch is the common base for my WIP series for ranges discards and to
remove discard_zeroes_data in favor of always using REQ_OP_WRITE_ZEROES,
so it would be good to get it in quickly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Add FC LLDD loopback driver to test FC host and target transport within
nvme-fabrics
To aid in the development and testing of the lower-level api of the FC
transport, this loopback driver has been created to act as if it were a
FC hba driver supporting both the host interfaces as well as the target
interfaces with the nvme FC transport.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Implements the FC-NVME T11 definition of how nvme fabric capsules are
performed on an FC fabric. Utilizes a lower-layer API to FC host adapters
to send/receive FC-4 LS operations and perform the FCP transactions
necessary to perform and FCP IO request for NVME.
The T11 definitions for FC-4 Link Services are implemented which create
NVMeOF connections. Implements the hooks with nvmet layer to pass NVME
commands to it for processing and posting of data/response base to the
host via the different connections.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Implements the FC-NVME T11 definition of how nvme fabric capsules are
performed on an FC fabric. Utilizes a lower-layer API to FC host adapters
to send/receive FC-4 LS operations and FCP operations that comprise NVME
over FC operation.
The T11 definitions for FC-4 Link Services are implemented which create
NVMeOF connections. Implements the hooks with blk-mq to then submit admin
and io requests to the different connections.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|