summaryrefslogtreecommitdiffstats
path: root/drivers/nvme/host/multipath.c
AgeCommit message (Collapse)AuthorFilesLines
2020-09-24bdi: replace BDI_CAP_STABLE_WRITES with a queue and a sb flagChristoph Hellwig1-7/+3
The BDI_CAP_STABLE_WRITES is one of the few bits of information in the backing_dev_info shared between the block drivers and the writeback code. To help untangling the dependency replace it with a queue flag and a superblock flag derived from it. This also helps with the case of e.g. a file system requiring stable writes due to its own checksumming, but not forcing it on other users of the block device like the swap code. One downside is that we an't support the stable_pages_required bdi attribute in sysfs anymore. It is replaced with a queue attribute which also is writable for easier testing. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-08-21nvme: refactor command completionChristoph Hellwig1-34/+13
Lift all the code to decide the dispostition of a completed command from nvme_complete_rq and nvme_failover_req into a new helper, which returns an emum of the potential actions. nvme_complete_rq then just switches on those and calls the proper helper for the action. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-08-21nvme: multipath: round-robin: eliminate "fallback" variableMartin Wilck1-5/+4
If we find an optimized path, we quit the loop immediately. Thus we can use just one variable for the next path, slighly simplifying the code. Signed-off-by: Martin Wilck <mwilck@suse.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-08-21nvme: multipath: round-robin: fix single non-optimized path caseMartin Wilck1-5/+10
If there's only one usable, non-optimized path, nvme_round_robin_path() returns NULL, which is wrong. Fix it by falling back to "old", like in the single optimized path case. Also, if the active path isn't changed, there's no need to re-assign the pointer. Fixes: 3f6e3246db0e ("nvme-multipath: fix logic for non-optimized paths") Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Martin George <marting@netapp.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-07-29nvme-multipath: do not fall back to __nvme_find_path() for non-optimized pathsHannes Reinecke1-4/+7
When nvme_round_robin_path() finds a valid namespace we should be using it; falling back to __nvme_find_path() for non-optimized paths will cause the result from nvme_round_robin_path() to be ignored for non-optimized paths. Fixes: 75c10e732724 ("nvme-multipath: round-robin I/O policy") Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-07-29nvme-multipath: fix logic for non-optimized pathsMartin Wilck1-0/+6
Handle the special case where we have exactly one optimized path, which we should keep using in this case. Fixes: 75c10e732724 ("nvme-multipath: round-robin I/O policy") Signed off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-07-29nvme: fix deadlock in disconnect during scan_work and/or ana_workSagi Grimberg1-3/+15
A deadlock happens in the following scenario with multipath: 1) scan_work(nvme0) detects a new nsid while nvme0 is an optimized path to it, path nvme1 happens to be inaccessible. 2) Before scan_work is complete nvme0 disconnect is initiated nvme_delete_ctrl_sync() sets nvme0 state to NVME_CTRL_DELETING 3) scan_work(1) attempts to submit IO, but nvme_path_is_optimized() observes nvme0 is not LIVE. Since nvme1 is a possible path IO is requeued and scan_work hangs. -- Workqueue: nvme-wq nvme_scan_work [nvme_core] kernel: Call Trace: kernel: __schedule+0x2b9/0x6c0 kernel: schedule+0x42/0xb0 kernel: io_schedule+0x16/0x40 kernel: do_read_cache_page+0x438/0x830 kernel: read_cache_page+0x12/0x20 kernel: read_dev_sector+0x27/0xc0 kernel: read_lba+0xc1/0x220 kernel: efi_partition+0x1e6/0x708 kernel: check_partition+0x154/0x244 kernel: rescan_partitions+0xae/0x280 kernel: __blkdev_get+0x40f/0x560 kernel: blkdev_get+0x3d/0x140 kernel: __device_add_disk+0x388/0x480 kernel: device_add_disk+0x13/0x20 kernel: nvme_mpath_set_live+0x119/0x140 [nvme_core] kernel: nvme_update_ns_ana_state+0x5c/0x60 [nvme_core] kernel: nvme_set_ns_ana_state+0x1e/0x30 [nvme_core] kernel: nvme_parse_ana_log+0xa1/0x180 [nvme_core] kernel: nvme_mpath_add_disk+0x47/0x90 [nvme_core] kernel: nvme_validate_ns+0x396/0x940 [nvme_core] kernel: nvme_scan_work+0x24f/0x380 [nvme_core] kernel: process_one_work+0x1db/0x380 kernel: worker_thread+0x249/0x400 kernel: kthread+0x104/0x140 -- 4) Delete also hangs in flush_work(ctrl->scan_work) from nvme_remove_namespaces(). Similiarly a deadlock with ana_work may happen: if ana_work has started and calls nvme_mpath_set_live and device_add_disk, it will trigger I/O. When we trigger disconnect I/O will block because our accessible (optimized) path is disconnecting, but the alternate path is inaccessible, so I/O blocks. Then disconnect tries to flush the ana_work and hangs. [ 605.550896] Workqueue: nvme-wq nvme_ana_work [nvme_core] [ 605.552087] Call Trace: [ 605.552683] __schedule+0x2b9/0x6c0 [ 605.553507] schedule+0x42/0xb0 [ 605.554201] io_schedule+0x16/0x40 [ 605.555012] do_read_cache_page+0x438/0x830 [ 605.556925] read_cache_page+0x12/0x20 [ 605.557757] read_dev_sector+0x27/0xc0 [ 605.558587] amiga_partition+0x4d/0x4c5 [ 605.561278] check_partition+0x154/0x244 [ 605.562138] rescan_partitions+0xae/0x280 [ 605.563076] __blkdev_get+0x40f/0x560 [ 605.563830] blkdev_get+0x3d/0x140 [ 605.564500] __device_add_disk+0x388/0x480 [ 605.565316] device_add_disk+0x13/0x20 [ 605.566070] nvme_mpath_set_live+0x5e/0x130 [nvme_core] [ 605.567114] nvme_update_ns_ana_state+0x2c/0x30 [nvme_core] [ 605.568197] nvme_update_ana_state+0xca/0xe0 [nvme_core] [ 605.569360] nvme_parse_ana_log+0xa1/0x180 [nvme_core] [ 605.571385] nvme_read_ana_log+0x76/0x100 [nvme_core] [ 605.572376] nvme_ana_work+0x15/0x20 [nvme_core] [ 605.573330] process_one_work+0x1db/0x380 [ 605.574144] worker_thread+0x4d/0x400 [ 605.574896] kthread+0x104/0x140 [ 605.577205] ret_from_fork+0x35/0x40 [ 605.577955] INFO: task nvme:14044 blocked for more than 120 seconds. [ 605.579239] Tainted: G OE 5.3.5-050305-generic #201910071830 [ 605.580712] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 605.582320] nvme D 0 14044 14043 0x00000000 [ 605.583424] Call Trace: [ 605.583935] __schedule+0x2b9/0x6c0 [ 605.584625] schedule+0x42/0xb0 [ 605.585290] schedule_timeout+0x203/0x2f0 [ 605.588493] wait_for_completion+0xb1/0x120 [ 605.590066] __flush_work+0x123/0x1d0 [ 605.591758] __cancel_work_timer+0x10e/0x190 [ 605.593542] cancel_work_sync+0x10/0x20 [ 605.594347] nvme_mpath_stop+0x2f/0x40 [nvme_core] [ 605.595328] nvme_stop_ctrl+0x12/0x50 [nvme_core] [ 605.596262] nvme_do_delete_ctrl+0x3f/0x90 [nvme_core] [ 605.597333] nvme_sysfs_delete+0x5c/0x70 [nvme_core] [ 605.598320] dev_attr_store+0x17/0x30 Fix this by introducing a new state: NVME_CTRL_DELETE_NOIO, which will indicate the phase of controller deletion where I/O cannot be allowed to access the namespace. NVME_CTRL_DELETING still allows mpath I/O to be issued to the bottom device, and only after we flush the ana_work and scan_work (after nvme_stop_ctrl and nvme_prep_remove_namespaces) we change the state to NVME_CTRL_DELETING_NOIO. Also we prevent ana_work from re-firing by aborting early if we are not LIVE, so we should be safe here. In addition, change the transport drivers to follow the updated state machine. Fixes: 0d0b660f214d ("nvme: add ANA support") Reported-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-07-08nvme: support for multiple Command Sets Supported and Effects log pagesKeith Busch1-1/+1
The Commands Supported and Effects log page was extended with a CSI field that enables the host to query the log page for each command set supported. Retrieve this log page for each command set that an attached namespace supports, and save a pointer to that log in the namespace head. Reviewed-by: Matias Bjørling <matias.bjorling@wdc.com> Reviewed-by: Javier González <javier.gonz@samsung.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Keith Busch <keith.busch@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-07-08Merge tag 'v5.8-rc4' into for-5.9/driversJens Axboe1-20/+33
Merge in 5.8-rc4 for-5.9/block to setup for-5.9/drivers, to provide a clean base and making the life for the NVMe changes easier. Signed-off-by: Jens Axboe <axboe@kernel.dk> * tag 'v5.8-rc4': (732 commits) Linux 5.8-rc4 x86/ldt: use "pr_info_once()" instead of open-coding it badly MIPS: Do not use smp_processor_id() in preemptible code MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen .gitignore: Do not track `defconfig` from `make savedefconfig` io_uring: fix regression with always ignoring signals in io_cqring_wait() x86/ldt: Disable 16-bit segments on Xen PV x86/entry/32: Fix #MC and #DB wiring on x86_32 x86/entry/xen: Route #DB correctly on Xen PV x86/entry, selftests: Further improve user entry sanity checks x86/entry/compat: Clear RAX high bits on Xen PV SYSENTER i2c: mlxcpld: check correct size of maximum RECV_LEN packet i2c: add Kconfig help text for slave mode i2c: slave-eeprom: update documentation i2c: eg20t: Load module automatically if ID matches i2c: designware: platdrv: Set class based on DMI i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665 mm/page_alloc: fix documentation error vmalloc: fix the owner argument for the new __vmalloc_node_range callers mm/cma.c: use exact_nid true to fix possible per-numa cma leak ...
2020-07-02nvme: fix a crash in nvme_mpath_add_diskChristoph Hellwig1-3/+4
For private namespaces ns->head_disk is NULL, so add a NULL check before updating the BDI capabilities. Fixes: b2ce4d90690b ("nvme-multipath: set bdi capabilities once") Reported-by: Avinash M N <Avinash.M.N@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
2020-07-01block: remove direct_make_requestChristoph Hellwig1-1/+1
Now that submit_bio_noacct has a decent blk-mq fast path there is no more need for this bypass. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-07-01block: rename generic_make_request to submit_bio_noacctChristoph Hellwig1-1/+1
generic_make_request has always been very confusingly misnamed, so rename it to submit_bio_noacct to make it clear that it is submit_bio minus accounting and a few checks. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-07-01block: move ->make_request_fn to struct block_device_operationsChristoph Hellwig1-3/+2
The make_request_fn is a little weird in that it sits directly in struct request_queue instead of an operation vector. Replace it with a block_device_operations method called submit_bio (which describes much better what it does). Also remove the request_queue argument to it, as the queue can be derived pretty trivially from the bio. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-07-01block: remove the request_queue argument from blk_queue_splitChristoph Hellwig1-5/+4
The queue can be trivially derived from the bio, so pass one less argument. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-06-24nvme-multipath: fix bogus request queue reference putSagi Grimberg1-0/+8
The mpath disk node takes a reference on the request mpath request queue when adding live path to the mpath gendisk. However if we connected to an inaccessible path device_add_disk is not called, so if we disconnect and remove the mpath gendisk we endup putting an reference on the request queue that was never taken [1]. Fix that to check if we ever added a live path (using NVME_NS_HEAD_HAS_DISK flag) and if not, clear the disk->queue reference. [1]: ------------[ cut here ]------------ refcount_t: underflow; use-after-free. WARNING: CPU: 1 PID: 1372 at lib/refcount.c:28 refcount_warn_saturate+0xa6/0xf0 CPU: 1 PID: 1372 Comm: nvme Tainted: G O 5.7.0-rc2+ #3 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-1ubuntu1 04/01/2014 RIP: 0010:refcount_warn_saturate+0xa6/0xf0 RSP: 0018:ffffb29e8053bdc0 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff8b7a2f4fc060 RCX: 0000000000000007 RDX: 0000000000000007 RSI: 0000000000000092 RDI: ffff8b7a3ec99980 RBP: ffff8b7a2f4fc000 R08: 00000000000002e1 R09: 0000000000000004 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000 R13: fffffffffffffff2 R14: ffffb29e8053bf08 R15: ffff8b7a320e2da0 FS: 00007f135d4ca800(0000) GS:ffff8b7a3ec80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005651178c0c30 CR3: 000000003b650005 CR4: 0000000000360ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: disk_release+0xa2/0xc0 device_release+0x28/0x80 kobject_put+0xa5/0x1b0 nvme_put_ns_head+0x26/0x70 [nvme_core] nvme_put_ns+0x30/0x60 [nvme_core] nvme_remove_namespaces+0x9b/0xe0 [nvme_core] nvme_do_delete_ctrl+0x43/0x5c [nvme_core] nvme_sysfs_delete.cold+0x8/0xd [nvme_core] kernfs_fop_write+0xc1/0x1a0 vfs_write+0xb6/0x1a0 ksys_write+0x5f/0xe0 do_syscall_64+0x52/0x1a0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Reported-by: Anton Eidelman <anton@lightbitslabs.com> Tested-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-06-24nvme-multipath: fix deadlock due to head->lockAnton Eidelman1-2/+2
In the following scenario scan_work and ana_work will deadlock: When scan_work calls nvme_mpath_add_disk() this holds ana_lock and invokes nvme_parse_ana_log(), which may issue IO in device_add_disk() and hang waiting for an accessible path. While nvme_mpath_set_live() only called when nvme_state_is_live(), a transition may cause NVME_SC_ANA_TRANSITION and requeue the IO. Since nvme_mpath_set_live() holds ns->head->lock, an ana_work on ANY ctrl will not be able to complete nvme_mpath_set_live() on the same ns->head, which is required in order to update the new accessible path and remove NVME_NS_ANA_PENDING.. Therefore IO never completes: deadlock [1]. Fix: Move device_add_disk out of the head->lock and protect it with an atomic test_and_set for a new NVME_NS_HEAD_HAS_DISK bit. [1]: kernel: INFO: task kworker/u8:2:160 blocked for more than 120 seconds. kernel: Tainted: G OE 5.3.5-050305-generic #201910071830 kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: kworker/u8:2 D 0 160 2 0x80004000 kernel: Workqueue: nvme-wq nvme_ana_work [nvme_core] kernel: Call Trace: kernel: __schedule+0x2b9/0x6c0 kernel: schedule+0x42/0xb0 kernel: schedule_preempt_disabled+0xe/0x10 kernel: __mutex_lock.isra.0+0x182/0x4f0 kernel: __mutex_lock_slowpath+0x13/0x20 kernel: mutex_lock+0x2e/0x40 kernel: nvme_update_ns_ana_state+0x22/0x60 [nvme_core] kernel: nvme_update_ana_state+0xca/0xe0 [nvme_core] kernel: nvme_parse_ana_log+0xa1/0x180 [nvme_core] kernel: nvme_read_ana_log+0x76/0x100 [nvme_core] kernel: nvme_ana_work+0x15/0x20 [nvme_core] kernel: process_one_work+0x1db/0x380 kernel: worker_thread+0x4d/0x400 kernel: kthread+0x104/0x140 kernel: ret_from_fork+0x35/0x40 kernel: INFO: task kworker/u8:4:439 blocked for more than 120 seconds. kernel: Tainted: G OE 5.3.5-050305-generic #201910071830 kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: kworker/u8:4 D 0 439 2 0x80004000 kernel: Workqueue: nvme-wq nvme_scan_work [nvme_core] kernel: Call Trace: kernel: __schedule+0x2b9/0x6c0 kernel: schedule+0x42/0xb0 kernel: io_schedule+0x16/0x40 kernel: do_read_cache_page+0x438/0x830 kernel: read_cache_page+0x12/0x20 kernel: read_dev_sector+0x27/0xc0 kernel: read_lba+0xc1/0x220 kernel: efi_partition+0x1e6/0x708 kernel: check_partition+0x154/0x244 kernel: rescan_partitions+0xae/0x280 kernel: __blkdev_get+0x40f/0x560 kernel: blkdev_get+0x3d/0x140 kernel: __device_add_disk+0x388/0x480 kernel: device_add_disk+0x13/0x20 kernel: nvme_mpath_set_live+0x119/0x140 [nvme_core] kernel: nvme_update_ns_ana_state+0x5c/0x60 [nvme_core] kernel: nvme_mpath_add_disk+0xbe/0x100 [nvme_core] kernel: nvme_validate_ns+0x396/0x940 [nvme_core] kernel: nvme_scan_work+0x256/0x390 [nvme_core] kernel: process_one_work+0x1db/0x380 kernel: worker_thread+0x4d/0x400 kernel: kthread+0x104/0x140 kernel: ret_from_fork+0x35/0x40 Fixes: 0d0b660f214d ("nvme: add ANA support") Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-06-24nvme: don't protect ns mutation with ns->head->lockSagi Grimberg1-8/+4
Right now ns->head->lock is protecting namespace mutation which is wrong and unneeded. Move it to only protect against head mutations. While we're at it, remove unnecessary ns->head reference as we already have head pointer. The problem with this is that the head->lock spans mpath disk node I/O that may block under some conditions (if for example the controller is disconnecting or the path became inaccessible), The locking scheme does not allow any other path to enable itself, preventing blocked I/O to complete and forward-progress from there. This is a preparation patch for the fix in a subsequent patch where the disk I/O will also be done outside the head->lock. Fixes: 0d0b660f214d ("nvme: add ANA support") Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-06-24nvme-multipath: fix deadlock between ana_work and scan_workAnton Eidelman1-8/+16
When scan_work calls nvme_mpath_add_disk() this holds ana_lock and invokes nvme_parse_ana_log(), which may issue IO in device_add_disk() and hang waiting for an accessible path. While nvme_mpath_set_live() only called when nvme_state_is_live(), a transition may cause NVME_SC_ANA_TRANSITION and requeue the IO. In order to recover and complete the IO ana_work on the same ctrl should be able to update the path state and remove NVME_NS_ANA_PENDING. The deadlock occurs because scan_work keeps holding ana_lock, so ana_work hangs [1]. Fix: Now nvme_mpath_add_disk() uses nvme_parse_ana_log() to obtain a copy of the ANA group desc, and then calls nvme_update_ns_ana_state() without holding ana_lock. [1]: kernel: Workqueue: nvme-wq nvme_scan_work [nvme_core] kernel: Call Trace: kernel: __schedule+0x2b9/0x6c0 kernel: schedule+0x42/0xb0 kernel: io_schedule+0x16/0x40 kernel: do_read_cache_page+0x438/0x830 kernel: read_cache_page+0x12/0x20 kernel: read_dev_sector+0x27/0xc0 kernel: read_lba+0xc1/0x220 kernel: efi_partition+0x1e6/0x708 kernel: check_partition+0x154/0x244 kernel: rescan_partitions+0xae/0x280 kernel: __blkdev_get+0x40f/0x560 kernel: blkdev_get+0x3d/0x140 kernel: __device_add_disk+0x388/0x480 kernel: device_add_disk+0x13/0x20 kernel: nvme_mpath_set_live+0x119/0x140 [nvme_core] kernel: nvme_update_ns_ana_state+0x5c/0x60 [nvme_core] kernel: nvme_set_ns_ana_state+0x1e/0x30 [nvme_core] kernel: nvme_parse_ana_log+0xa1/0x180 [nvme_core] kernel: nvme_mpath_add_disk+0x47/0x90 [nvme_core] kernel: nvme_validate_ns+0x396/0x940 [nvme_core] kernel: nvme_scan_work+0x24f/0x380 [nvme_core] kernel: process_one_work+0x1db/0x380 kernel: worker_thread+0x249/0x400 kernel: kthread+0x104/0x140 kernel: Workqueue: nvme-wq nvme_ana_work [nvme_core] kernel: Call Trace: kernel: __schedule+0x2b9/0x6c0 kernel: schedule+0x42/0xb0 kernel: schedule_preempt_disabled+0xe/0x10 kernel: __mutex_lock.isra.0+0x182/0x4f0 kernel: ? __switch_to_asm+0x34/0x70 kernel: ? select_task_rq_fair+0x1aa/0x5c0 kernel: ? kvm_sched_clock_read+0x11/0x20 kernel: ? sched_clock+0x9/0x10 kernel: __mutex_lock_slowpath+0x13/0x20 kernel: mutex_lock+0x2e/0x40 kernel: nvme_read_ana_log+0x3a/0x100 [nvme_core] kernel: nvme_ana_work+0x15/0x20 [nvme_core] kernel: process_one_work+0x1db/0x380 kernel: worker_thread+0x4d/0x400 kernel: kthread+0x104/0x140 kernel: ? process_one_work+0x380/0x380 kernel: ? kthread_park+0x80/0x80 kernel: ret_from_fork+0x35/0x40 Fixes: 0d0b660f214d ("nvme: add ANA support") Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-05-09nvme: define constants for identification valuesKeith Busch1-2/+3
Improve code readability by defining the specification's constants that the driver is using when decoding identification payloads. Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Bart van Assche <bvanassche@acm.org> Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Acked-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-05-09nvme-multipath: stop using ->queuedataChristoph Hellwig1-2/+1
nvme-multipath already uses the gendisk private data, not need to also set up the request_queue queuedata and use it in one place only. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-05-09nvme-multipath: set bdi capabilities onceKeith Busch1-0/+8
The queues' backing device info capabilities don't change with each namespace revalidation. Set it only when each path's request_queue is initially added to a multipath queue. Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-04-04nvme: fix deadlock caused by ANA update wrong lockingSagi Grimberg1-2/+2
The deadlock combines 4 flows in parallel: - ns scanning (triggered from reconnect) - request timeout - ANA update (triggered from reconnect) - I/O coming into the mpath device (1) ns scanning triggers disk revalidation -> update disk info -> freeze queue -> but blocked, due to (2) (2) timeout handler reference the g_usage_counter - > but blocks in the transport .timeout() handler, due to (3) (3) the transport timeout handler (indirectly) calls nvme_stop_queue() -> which takes the (down_read) namespaces_rwsem - > but blocks, due to (4) (4) ANA update takes the (down_write) namespaces_rwsem -> calls nvme_mpath_set_live() -> which synchronize the ns_head srcu (see commit 504db087aacc) -> but blocks, due to (5) (5) I/O came into nvme_mpath_make_request -> took srcu_read_lock -> direct_make_request > blk_queue_enter -> but blocked, due to (1) ==> the request queue is under freeze -> deadlock. The fix is making ANA update take a read lock as the namespaces list is not manipulated, it is just the ns and ns->head that are being updated (which is protected with the ns->head lock). Fixes: 0d0b660f214dc ("nvme: add ANA support") Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
2020-03-30Merge tag 'for-5.7/drivers-2020-03-29' of git://git.kernel.dk/linux-blockLinus Torvalds1-12/+9
Pull block driver updates from Jens Axboe: - floppy driver cleanup series from Willy - NVMe updates and fixes (Various) - null_blk trace improvements (Chaitanya) - bcache fixes (Coly) - md fixes (via Song) - loop block size change optimizations (Martijn) - scnprintf() use (Takashi) * tag 'for-5.7/drivers-2020-03-29' of git://git.kernel.dk/linux-block: (81 commits) null_blk: add trace in null_blk_zoned.c null_blk: add tracepoint helpers for zoned mode block: add a zone condition debug helper nvme: cleanup namespace identifier reporting in nvme_init_ns_head nvme: rename __nvme_find_ns_head to nvme_find_ns_head nvme: refactor nvme_identify_ns_descs error handling nvme-tcp: Add warning on state change failure at nvme_tcp_setup_ctrl nvme-rdma: Add warning on state change failure at nvme_rdma_setup_ctrl nvme: Fix controller creation races with teardown flow nvme: Make nvme_uninit_ctrl symmetric to nvme_init_ctrl nvme: Fix ctrl use-after-free during sysfs deletion nvme-pci: Re-order nvme_pci_free_ctrl nvme: Remove unused return code from nvme_delete_ctrl_sync nvme: Use nvme_state_terminal helper nvme: release ida resources nvme: Add compat_ioctl handler for NVME_IOCTL_SUBMIT_IO nvmet-tcp: optimize tcp stack TX when data digest is used nvme-fabrics: Use scnprintf() for avoiding potential buffer overflow nvme-multipath: do not reset on unknown status nvmet-rdma: allocate RW ctxs according to mdts ...
2020-03-27block: simplify queue allocationChristoph Hellwig1-2/+1
Current make_request based drivers use either blk_alloc_queue_node or blk_alloc_queue to allocate a queue, and then set up the make_request_fn function pointer and a few parameters using the blk_queue_make_request helper. Simplify this by passing the make_request pointer to blk_alloc_queue, and while at it merge the _node variant into the main helper by always passing a node_id, and remove the superfluous gfp_mask parameter. A lower-level __blk_alloc_queue is kept for the blk-mq case. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-03-26nvme-multipath: do not reset on unknown statusJohn Meneghini1-12/+9
The nvme multipath error handling defaults to controller reset if the error is unknown. There are, however, no existing nvme status codes that indicate a reset should be used, and resetting causes unnecessary disruption to the rest of IO. Change nvme's error handling to first check if failover should happen. If not, let the normal error handling take over rather than reset the controller. Based-on-a-patch-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: John Meneghini <johnm@netapp.com> Signed-off-by: Keith Busch <kbusch@kernel.org>
2020-02-21nvme-multipath: Fix memory leak with ana_log_bufLogan Gunthorpe1-0/+1
kmemleak reports a memory leak with the ana_log_buf allocated by nvme_mpath_init(): unreferenced object 0xffff888120e94000 (size 8208): comm "nvme", pid 6884, jiffies 4295020435 (age 78786.312s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 ................ 01 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000e2360188>] kmalloc_order+0x97/0xc0 [<0000000079b18dd4>] kmalloc_order_trace+0x24/0x100 [<00000000f50c0406>] __kmalloc+0x24c/0x2d0 [<00000000f31a10b9>] nvme_mpath_init+0x23c/0x2b0 [<000000005802589e>] nvme_init_identify+0x75f/0x1600 [<0000000058ef911b>] nvme_loop_configure_admin_queue+0x26d/0x280 [<00000000673774b9>] nvme_loop_create_ctrl+0x2a7/0x710 [<00000000f1c7a233>] nvmf_dev_write+0xc66/0x10b9 [<000000004199f8d0>] __vfs_write+0x50/0xa0 [<0000000065466fef>] vfs_write+0xf3/0x280 [<00000000b0db9a8b>] ksys_write+0xc6/0x160 [<0000000082156b91>] __x64_sys_write+0x43/0x50 [<00000000c34fbb6d>] do_syscall_64+0x77/0x2f0 [<00000000bbc574c9>] entry_SYSCALL_64_after_hwframe+0x49/0xbe nvme_mpath_init() is called by nvme_init_identify() which is called in multiple places (nvme_reset_work(), nvme_passthru_end(), etc). This means nvme_mpath_init() may be called multiple times before nvme_mpath_uninit() (which is only called on nvme_free_ctrl()). When nvme_mpath_init() is called multiple times, it overwrites the ana_log_buf pointer with a new allocation, thus leaking the previous allocation. To fix this, free ana_log_buf before allocating a new one. Fixes: 0d0b660f214dc490 ("nvme: add ANA support") Cc: <stable@vger.kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Keith Busch <kbusch@kernel.org>
2019-11-25Merge tag 'for-5.5/drivers-20191121' of git://git.kernel.dk/linux-blockLinus Torvalds1-4/+9
Pull block driver updates from Jens Axboe: "Here are the main block driver updates for 5.5. Nothing major in here, mostly just fixes. This contains: - a set of bcache changes via Coly - MD changes from Song - loop unmap write-zeroes fix (Darrick) - spelling fixes (Geert) - zoned additions cleanups to null_blk/dm (Ajay) - allow null_blk online submit queue changes (Bart) - NVMe changes via Keith, nothing major here either" * tag 'for-5.5/drivers-20191121' of git://git.kernel.dk/linux-block: (56 commits) Revert "bcache: fix fifo index swapping condition in journal_pin_cmp()" drivers/md/raid5-ppl.c: use the new spelling of RWH_WRITE_LIFE_NOT_SET drivers/md/raid5.c: use the new spelling of RWH_WRITE_LIFE_NOT_SET bcache: don't export symbols bcache: remove the extra cflags for request.o bcache: at least try to shrink 1 node in bch_mca_scan() bcache: add idle_max_writeback_rate sysfs interface bcache: add code comments in bch_btree_leaf_dirty() bcache: fix deadlock in bcache_allocator bcache: add code comment bch_keylist_pop() and bch_keylist_pop_front() bcache: deleted code comments for dead code in bch_data_insert_keys() bcache: add more accurate error messages in read_super() bcache: fix static checker warning in bcache_device_free() bcache: fix a lost wake-up problem caused by mca_cannibalize_lock bcache: fix fifo index swapping condition in journal_pin_cmp() md/raid10: prevent access of uninitialized resync_pages offset md: avoid invalid memory access for array sb->dev_roles md/raid1: avoid soft lockup under high load null_blk: add zone open, close, and finish support dm: add zone open, close and finish support ...
2019-11-06nvme-multipath: fix crash in nvme_mpath_clear_ctrl_pathsAnton Eidelman1-0/+2
nvme_mpath_clear_ctrl_paths() iterates through the ctrl->namespaces list while holding ctrl->scan_lock. This does not seem to be the correct way of protecting from concurrent list modification. Specifically, nvme_scan_work() sorts ctrl->namespaces AFTER unlocking scan_lock. This may result in the following (rare) crash in ctrl disconnect during scan_work: BUG: kernel NULL pointer dereference, address: 0000000000000050 Oops: 0000 [#1] SMP PTI CPU: 0 PID: 3995 Comm: nvme 5.3.5-050305-generic RIP: 0010:nvme_mpath_clear_current_path+0xe/0x90 [nvme_core] ... Call Trace: nvme_mpath_clear_ctrl_paths+0x3c/0x70 [nvme_core] nvme_remove_namespaces+0x35/0xe0 [nvme_core] nvme_do_delete_ctrl+0x47/0x90 [nvme_core] nvme_sysfs_delete+0x49/0x60 [nvme_core] dev_attr_store+0x17/0x30 sysfs_kf_write+0x3e/0x50 kernfs_fop_write+0x11e/0x1a0 __vfs_write+0x1b/0x40 vfs_write+0xb9/0x1a0 ksys_write+0x67/0xe0 __x64_sys_write+0x1a/0x20 do_syscall_64+0x5a/0x130 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f8d02bfb154 Fix: After taking scan_lock in nvme_mpath_clear_ctrl_paths() down_read(&ctrl->namespaces_rwsem) as well to make list traversal safe. This will not cause deadlocks because taking scan_lock never happens while holding the namespaces_rwsem. Moreover, scan work downs namespaces_rwsem in the same order. Alternative: sort ctrl->namespaces in nvme_scan_work() while still holding the scan_lock. This would leave nvme_mpath_clear_ctrl_paths() without correct protection against ctrl->namespaces modification by anyone other than scan_work. Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Keith Busch <kbusch@kernel.org>
2019-11-04nvme: Fix parsing of ANA log pagePrabhath Sajeepa1-4/+8
Check validity of offset into ANA log buffer before accessing nvme_ana_group_desc. This check ensures the size of ANA log buffer >= offset + sizeof(nvme_ana_group_desc) Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Prabhath Sajeepa <psajeepa@purestorage.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-11-04nvme: introduce "Command Aborted By host" status codeMax Gurtovoy1-0/+1
Fix the status code of canceled requests initiated by the host according to TP4028 (Status Code 0x371): "Command Aborted By host: The command was aborted as a result of host action (e.g., the host disconnected the Fabric connection)." Also in a multipath environment, unless otherwise specified, errors of this type (path related) should be retried using a different path, if one is available. Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-10-29nvme-multipath: remove unused groups_only mode in ana logAnton Eidelman1-5/+4
groups_only mode in nvme_read_ana_log() is no longer used: remove it. Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-10-29nvme-multipath: fix possible io hang after ctrl reconnectAnton Eidelman1-1/+1
The following scenario results in an IO hang: 1) ctrl completes a request with NVME_SC_ANA_TRANSITION. NVME_NS_ANA_PENDING bit in ns->flags is set and ana_work is triggered. 2) ana_work: nvme_read_ana_log() tries to get the ANA log page from the ctrl. This fails because ctrl disconnects. Therefore nvme_update_ns_ana_state() is not called and NVME_NS_ANA_PENDING bit in ns->flags is not cleared. 3) ctrl reconnects: nvme_mpath_init(ctrl,...) calls nvme_read_ana_log(ctrl, groups_only=true). However, nvme_update_ana_state() does not update namespaces because nr_nsids = 0 (due to groups_only mode). 4) scan_work calls nvme_validate_ns() finds the ns and re-validates OK. Result: The ctrl is now live but NVME_NS_ANA_PENDING bit in ns->flags is still set. Consequently ctrl will never be considered a viable path by __nvme_find_path(). IO will hang if ctrl is the only or the last path to the namespace. More generally, while ctrl is reconnecting, its ANA state may change. And because nvme_mpath_init() requests ANA log in groups_only mode, these changes are not propagated to the existing ctrl namespaces. This may result in a mal-function or an IO hang. Solution: nvme_mpath_init() will nvme_read_ana_log() with groups_only set to false. This will not harm the new ctrl case (no namespaces present), and will make sure the ANA state of namespaces gets updated after reconnect. Note: Another option would be for nvme_mpath_init() to invoke nvme_parse_ana_log(..., nvme_set_ns_ana_state) for each existing namespace. Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-09-17Merge tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-blockLinus Torvalds1-3/+5
Pull block updates from Jens Axboe: - Two NVMe pull requests: - ana log parse fix from Anton - nvme quirks support for Apple devices from Ben - fix missing bio completion tracing for multipath stack devices from Hannes and Mikhail - IP TOS settings for nvme rdma and tcp transports from Israel - rq_dma_dir cleanups from Israel - tracing for Get LBA Status command from Minwoo - Some nvme-tcp cleanups from Minwoo, Potnuri and Myself - Some consolidation between the fabrics transports for handling the CAP register - reset race with ns scanning fix for fabrics (move fabrics commands to a dedicated request queue with a different lifetime from the admin request queue)." - controller reset and namespace scan races fixes - nvme discovery log change uevent support - naming improvements from Keith - multiple discovery controllers reject fix from James - some regular cleanups from various people - Series fixing (and re-fixing) null_blk debug printing and nr_devices checks (André) - A few pull requests from Song, with fixes from Andy, Guoqing, Guilherme, Neil, Nigel, and Yufen. - REQ_OP_ZONE_RESET_ALL support (Chaitanya) - Bio merge handling unification (Christoph) - Pick default elevator correctly for devices with special needs (Damien) - Block stats fixes (Hou) - Timeout and support devices nbd fixes (Mike) - Series fixing races around elevator switching and device add/remove (Ming) - sed-opal cleanups (Revanth) - Per device weight support for BFQ (Fam) - Support for blk-iocost, a new model that can properly account cost of IO workloads. (Tejun) - blk-cgroup writeback fixes (Tejun) - paride queue init fixes (zhengbin) - blk_set_runtime_active() cleanup (Stanley) - Block segment mapping optimizations (Bart) - lightnvm fixes (Hans/Minwoo/YueHaibing) - Various little fixes and cleanups * tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block: (186 commits) null_blk: format pr_* logs with pr_fmt null_blk: match the type of parameter nr_devices null_blk: do not fail the module load with zero devices block: also check RQF_STATS in blk_mq_need_time_stamp() block: make rq sector size accessible for block stats bfq: Fix bfq linkage error raid5: use bio_end_sector in r5_next_bio raid5: remove STRIPE_OPS_REQ_PENDING md: add feature flag MD_FEATURE_RAID0_LAYOUT md/raid0: avoid RAID0 data corruption due to layout confusion. raid5: don't set STRIPE_HANDLE to stripe which is in batch list raid5: don't increment read_errors on EILSEQ return nvmet: fix a wrong error status returned in error log page nvme: send discovery log page change events to userspace nvme: add uevent variables for controller devices nvme: enable aen regardless of the presence of I/O queues nvme-fabrics: allow discovery subsystems accept a kato nvmet: Use PTR_ERR_OR_ZERO() in nvmet_init_discovery() nvme: Remove redundant assignment of cq vector nvme: Assign subsys instance from first ctrl ...
2019-08-29nvme-multipath: fix ana log nsid lookup when nsid is not foundAnton Eidelman1-3/+5
ANA log parsing invokes nvme_update_ana_state() per ANA group desc. This updates the state of namespaces with nsids in desc->nsids[]. Both ctrl->namespaces list and desc->nsids[] array are sorted by nsid. Hence nvme_update_ana_state() performs a single walk over ctrl->namespaces: - if current namespace matches the current desc->nsids[n], this namespace is updated, and n is incremented. - the process stops when it encounters the end of either ctrl->namespaces end or desc->nsids[] In case desc->nsids[n] does not match any of ctrl->namespaces, the remaining nsids following desc->nsids[n] will not be updated. Such situation was considered abnormal and generated WARN_ON_ONCE. However ANA log MAY contain nsids not (yet) found in ctrl->namespaces. For example, lets consider the following scenario: - nvme0 exposes namespaces with nsids = [2, 3] to the host - a new namespace nsid = 1 is added dynamically - also, a ANA topology change is triggered - NS_CHANGED aen is generated and triggers scan_work - before scan_work discovers nsid=1 and creates a namespace, a NOTICE_ANA aen was issues and ana_work receives ANA log with nsids=[1, 2, 3] Result: ana_work fails to update ANA state on existing namespaces [2, 3] Solution: Change the way nvme_update_ana_state() namespace list walk checks the current namespace against desc->nsids[n] as follows: a) ns->head->ns_id < desc->nsids[n]: keep walking ctrl->namespaces. b) ns->head->ns_id == desc->nsids[n]: match, update the namespace c) ns->head->ns_id >= desc->nsids[n]: skip to desc->nsids[n+1] This enables correct operation in the scenario described above. This also allows ANA log to contain nsids currently invisible to the host, i.e. inactive nsids. Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Reviewed-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
2019-08-20nvme-multipath: fix possible I/O hang when paths are updatedAnton Eidelman1-0/+1
nvme_state_set_live() making a path available triggers requeue_work in order to resubmit requests that ended up on requeue_list when no paths were available. This requeue_work may race with concurrent nvme_ns_head_make_request() that do not observe the live path yet. Such concurrent requests may by made by either: - New IO submission. - Requeue_work triggered by nvme_failover_req() or another ana_work. A race may cause requeue_work capture the state of requeue_list before more requests get onto the list. These requests will stay on the list forever unless requeue_work is triggered again. In order to prevent such race, nvme_state_set_live() should synchronize_srcu(&head->srcu) before triggering the requeue_work and prevent nvme_ns_head_make_request referencing an old snapshot of the path list. Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-07-31nvme: fix controller removal race with scan workSagi Grimberg1-6/+40
With multipath enabled, nvme_scan_work() can read from the device (through nvme_mpath_add_disk()) and hang [1]. However, with fabrics, once ctrl->state is set to NVME_CTRL_DELETING, the reads will hang (see nvmf_check_ready()) and the mpath stack device make_request will block if head->list is not empty. However, when the head->list consistst of only DELETING/DEAD controllers, we should actually not block, but rather fail immediately. In addition, before we go ahead and remove the namespaces, make sure to clear the current path and kick the requeue list so that the request will fast fail upon requeuing. [1]: -- INFO: task kworker/u4:3:166 blocked for more than 120 seconds. Not tainted 5.2.0-rc6-vmlocalyes-00005-g808c8c2dc0cf #316 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u4:3 D 0 166 2 0x80004000 Workqueue: nvme-wq nvme_scan_work Call Trace: __schedule+0x851/0x1400 schedule+0x99/0x210 io_schedule+0x21/0x70 do_read_cache_page+0xa57/0x1330 read_cache_page+0x4a/0x70 read_dev_sector+0xbf/0x380 amiga_partition+0xc4/0x1230 check_partition+0x30f/0x630 rescan_partitions+0x19a/0x980 __blkdev_get+0x85a/0x12f0 blkdev_get+0x2a5/0x790 __device_add_disk+0xe25/0x1250 device_add_disk+0x13/0x20 nvme_mpath_set_live+0x172/0x2b0 nvme_update_ns_ana_state+0x130/0x180 nvme_set_ns_ana_state+0x9a/0xb0 nvme_parse_ana_log+0x1c3/0x4a0 nvme_mpath_add_disk+0x157/0x290 nvme_validate_ns+0x1017/0x1bd0 nvme_scan_work+0x44d/0x6a0 process_one_work+0x7d7/0x1240 worker_thread+0x8e/0xff0 kthread+0x2c3/0x3b0 ret_from_fork+0x35/0x40 INFO: task kworker/u4:1:1034 blocked for more than 120 seconds. Not tainted 5.2.0-rc6-vmlocalyes-00005-g808c8c2dc0cf #316 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/u4:1 D 0 1034 2 0x80004000 Workqueue: nvme-delete-wq nvme_delete_ctrl_work Call Trace: __schedule+0x851/0x1400 schedule+0x99/0x210 schedule_timeout+0x390/0x830 wait_for_completion+0x1a7/0x310 __flush_work+0x241/0x5d0 flush_work+0x10/0x20 nvme_remove_namespaces+0x85/0x3d0 nvme_do_delete_ctrl+0xb4/0x1e0 nvme_delete_ctrl_work+0x15/0x20 process_one_work+0x7d7/0x1240 worker_thread+0x8e/0xff0 kthread+0x2c3/0x3b0 ret_from_fork+0x35/0x40 -- Reported-by: Logan Gunthorpe <logang@deltatee.com> Tested-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
2019-07-31nvme: fix a possible deadlock when passthru commands sent to a multipath deviceSagi Grimberg1-0/+30
When the user issues a command with side effects, we will end up freezing the namespace request queue when updating disk info (and the same for the corresponding mpath disk node). However, we are not freezing the mpath node request queue, which means that mpath I/O can still come in and block on blk_queue_enter (called from nvme_ns_head_make_request -> direct_make_request). This is a deadlock, because blk_queue_enter will block until the inner namespace request queue is unfroze, but that process is blocked because the namespace revalidation is trying to update the mpath disk info and freeze its request queue (which will never complete because of the I/O that is blocked on blk_queue_enter). Fix this by freezing all the subsystem nsheads request queues before executing the passthru command. Given that these commands are infrequent we should not worry about this temporary I/O freeze to keep things sane. Here is the matching hang traces: -- [ 374.465002] INFO: task systemd-udevd:17994 blocked for more than 122 seconds. [ 374.472975] Not tainted 5.2.0-rc3-mpdebug+ #42 [ 374.478522] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 374.487274] systemd-udevd D 0 17994 1 0x00000000 [ 374.493407] Call Trace: [ 374.496145] __schedule+0x2ef/0x620 [ 374.500047] schedule+0x38/0xa0 [ 374.503569] blk_queue_enter+0x139/0x220 [ 374.507959] ? remove_wait_queue+0x60/0x60 [ 374.512540] direct_make_request+0x60/0x130 [ 374.517219] nvme_ns_head_make_request+0x11d/0x420 [nvme_core] [ 374.523740] ? generic_make_request_checks+0x307/0x6f0 [ 374.529484] generic_make_request+0x10d/0x2e0 [ 374.534356] submit_bio+0x75/0x140 [ 374.538163] ? guard_bio_eod+0x32/0xe0 [ 374.542361] submit_bh_wbc+0x171/0x1b0 [ 374.546553] block_read_full_page+0x1ed/0x330 [ 374.551426] ? check_disk_change+0x70/0x70 [ 374.556008] ? scan_shadow_nodes+0x30/0x30 [ 374.560588] blkdev_readpage+0x18/0x20 [ 374.564783] do_read_cache_page+0x301/0x860 [ 374.569463] ? blkdev_writepages+0x10/0x10 [ 374.574037] ? prep_new_page+0x88/0x130 [ 374.578329] ? get_page_from_freelist+0xa2f/0x1280 [ 374.583688] ? __alloc_pages_nodemask+0x179/0x320 [ 374.588947] read_cache_page+0x12/0x20 [ 374.593142] read_dev_sector+0x2d/0xd0 [ 374.597337] read_lba+0x104/0x1f0 [ 374.601046] find_valid_gpt+0xfa/0x720 [ 374.605243] ? string_nocheck+0x58/0x70 [ 374.609534] ? find_valid_gpt+0x720/0x720 [ 374.614016] efi_partition+0x89/0x430 [ 374.618113] ? string+0x48/0x60 [ 374.621632] ? snprintf+0x49/0x70 [ 374.625339] ? find_valid_gpt+0x720/0x720 [ 374.629828] check_partition+0x116/0x210 [ 374.634214] rescan_partitions+0xb6/0x360 [ 374.638699] __blkdev_reread_part+0x64/0x70 [ 374.643377] blkdev_reread_part+0x23/0x40 [ 374.647860] blkdev_ioctl+0x48c/0x990 [ 374.651956] block_ioctl+0x41/0x50 [ 374.655766] do_vfs_ioctl+0xa7/0x600 [ 374.659766] ? locks_lock_inode_wait+0xb1/0x150 [ 374.664832] ksys_ioctl+0x67/0x90 [ 374.668539] __x64_sys_ioctl+0x1a/0x20 [ 374.672732] do_syscall_64+0x5a/0x1c0 [ 374.676828] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 374.738474] INFO: task nvmeadm:49141 blocked for more than 123 seconds. [ 374.745871] Not tainted 5.2.0-rc3-mpdebug+ #42 [ 374.751419] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 374.760170] nvmeadm D 0 49141 36333 0x00004080 [ 374.766301] Call Trace: [ 374.769038] __schedule+0x2ef/0x620 [ 374.772939] schedule+0x38/0xa0 [ 374.776452] blk_mq_freeze_queue_wait+0x59/0x100 [ 374.781614] ? remove_wait_queue+0x60/0x60 [ 374.786192] blk_mq_freeze_queue+0x1a/0x20 [ 374.790773] nvme_update_disk_info.isra.57+0x5f/0x350 [nvme_core] [ 374.797582] ? nvme_identify_ns.isra.50+0x71/0xc0 [nvme_core] [ 374.804006] __nvme_revalidate_disk+0xe5/0x110 [nvme_core] [ 374.810139] nvme_revalidate_disk+0xa6/0x120 [nvme_core] [ 374.816078] ? nvme_submit_user_cmd+0x11e/0x320 [nvme_core] [ 374.822299] nvme_user_cmd+0x264/0x370 [nvme_core] [ 374.827661] nvme_dev_ioctl+0x112/0x1d0 [nvme_core] [ 374.833114] do_vfs_ioctl+0xa7/0x600 [ 374.837117] ? __audit_syscall_entry+0xdd/0x130 [ 374.842184] ksys_ioctl+0x67/0x90 [ 374.845891] __x64_sys_ioctl+0x1a/0x20 [ 374.850082] do_syscall_64+0x5a/0x1c0 [ 374.854178] entry_SYSCALL_64_after_hwframe+0x44/0xa9 -- Reported-by: James Puthukattukaran <james.puthukattukaran@oracle.com> Tested-by: James Puthukattukaran <james.puthukattukaran@oracle.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
2019-07-23nvme: fix multipath crash when ANA is deactivatedMarta Rybczynska1-6/+2
Fix a crash with multipath activated. It happends when ANA log page is larger than MDTS and because of that ANA is disabled. The driver then tries to access unallocated buffer when connecting to a nvme target. The signature is as follows: [ 300.433586] nvme nvme0: ANA log page size (8208) larger than MDTS (8192). [ 300.435387] nvme nvme0: disabling ANA support. [ 300.437835] nvme nvme0: creating 4 I/O queues. [ 300.459132] nvme nvme0: new ctrl: NQN "nqn.0.0.0", addr 10.91.0.1:8009 [ 300.464609] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 [ 300.466342] #PF error: [normal kernel read fault] [ 300.467385] PGD 0 P4D 0 [ 300.467987] Oops: 0000 [#1] SMP PTI [ 300.468787] CPU: 3 PID: 50 Comm: kworker/u8:1 Not tainted 5.0.20kalray+ #4 [ 300.470264] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 300.471532] Workqueue: nvme-wq nvme_scan_work [nvme_core] [ 300.472724] RIP: 0010:nvme_parse_ana_log+0x21/0x140 [nvme_core] [ 300.474038] Code: 45 01 d2 d8 48 98 c3 66 90 0f 1f 44 00 00 41 57 41 56 41 55 41 54 55 53 48 89 fb 48 83 ec 08 48 8b af 20 0a 00 00 48 89 34 24 <66> 83 7d 08 00 0f 84 c6 00 00 00 44 8b 7d 14 49 89 d5 8b 55 10 48 [ 300.477374] RSP: 0018:ffffa50e80fd7cb8 EFLAGS: 00010296 [ 300.478334] RAX: 0000000000000001 RBX: ffff9130f1872258 RCX: 0000000000000000 [ 300.479784] RDX: ffffffffc06c4c30 RSI: ffff9130edad4280 RDI: ffff9130f1872258 [ 300.481488] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000044 [ 300.483203] R10: 0000000000000220 R11: 0000000000000040 R12: ffff9130f18722c0 [ 300.484928] R13: ffff9130f18722d0 R14: ffff9130edad4280 R15: ffff9130f18722c0 [ 300.486626] FS: 0000000000000000(0000) GS:ffff9130f7b80000(0000) knlGS:0000000000000000 [ 300.488538] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 300.489907] CR2: 0000000000000008 CR3: 00000002365e6000 CR4: 00000000000006e0 [ 300.491612] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 300.493303] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 300.494991] Call Trace: [ 300.495645] nvme_mpath_add_disk+0x5c/0xb0 [nvme_core] [ 300.496880] nvme_validate_ns+0x2ef/0x550 [nvme_core] [ 300.498105] ? nvme_identify_ctrl.isra.45+0x6a/0xb0 [nvme_core] [ 300.499539] nvme_scan_work+0x2b4/0x370 [nvme_core] [ 300.500717] ? __switch_to_asm+0x35/0x70 [ 300.501663] process_one_work+0x171/0x380 [ 300.502340] worker_thread+0x49/0x3f0 [ 300.503079] kthread+0xf8/0x130 [ 300.503795] ? max_active_store+0x80/0x80 [ 300.504690] ? kthread_bind+0x10/0x10 [ 300.505502] ret_from_fork+0x35/0x40 [ 300.506280] Modules linked in: nvme_tcp nvme_rdma rdma_cm iw_cm ib_cm ib_core nvme_fabrics nvme_core xt_physdev ip6table_raw ip6table_mangle ip6table_filter ip6_tables xt_comment iptable_nat nf_nat_ipv4 nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xt_CHECKSUM iptable_mangle iptable_filter veth ebtable_filter ebtable_nat ebtables iptable_raw vxlan ip6_udp_tunnel udp_tunnel sunrpc joydev pcspkr virtio_balloon br_netfilter bridge stp llc ip_tables xfs libcrc32c ata_generic pata_acpi virtio_net virtio_console net_failover virtio_blk failover ata_piix serio_raw libata virtio_pci virtio_ring virtio [ 300.514984] CR2: 0000000000000008 [ 300.515569] ---[ end trace faa2eefad7e7f218 ]--- [ 300.516354] RIP: 0010:nvme_parse_ana_log+0x21/0x140 [nvme_core] [ 300.517330] Code: 45 01 d2 d8 48 98 c3 66 90 0f 1f 44 00 00 41 57 41 56 41 55 41 54 55 53 48 89 fb 48 83 ec 08 48 8b af 20 0a 00 00 48 89 34 24 <66> 83 7d 08 00 0f 84 c6 00 00 00 44 8b 7d 14 49 89 d5 8b 55 10 48 [ 300.520353] RSP: 0018:ffffa50e80fd7cb8 EFLAGS: 00010296 [ 300.521229] RAX: 0000000000000001 RBX: ffff9130f1872258 RCX: 0000000000000000 [ 300.522399] RDX: ffffffffc06c4c30 RSI: ffff9130edad4280 RDI: ffff9130f1872258 [ 300.523560] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000044 [ 300.524734] R10: 0000000000000220 R11: 0000000000000040 R12: ffff9130f18722c0 [ 300.525915] R13: ffff9130f18722d0 R14: ffff9130edad4280 R15: ffff9130f18722c0 [ 300.527084] FS: 0000000000000000(0000) GS:ffff9130f7b80000(0000) knlGS:0000000000000000 [ 300.528396] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 300.529440] CR2: 0000000000000008 CR3: 00000002365e6000 CR4: 00000000000006e0 [ 300.530739] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 300.531989] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 300.533264] Kernel panic - not syncing: Fatal exception [ 300.534338] Kernel Offset: 0x17c00000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff) [ 300.536227] ---[ end Kernel panic - not syncing: Fatal exception ]--- Condition check refactoring from Christoph Hellwig. Signed-off-by: Marta Rybczynska <marta.rybczynska@kalray.eu> Tested-by: Jean-Baptiste Riaux <jbriaux@kalray.eu> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-07-09nvme-multipath: do not select namespaces which are about to be removedHannes Reinecke1-1/+2
nvme_ns_remove() will first set the NVME_NS_REMOVING flag before removing it from the list at the very last step. So to avoid selecting a namespace in nvme_find_path() which is about to be removed check the NVME_NS_REMOVING flag, too, when selecting a new path. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-07-09nvme-multipath: also check for a disabled path if there is a single siblingHannes Reinecke1-1/+4
When we have a singular list in nvme_round_robin_path() we still need to check its validity. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-07-09nvme-multipath: factor out a nvme_path_is_disabled helperHannes Reinecke1-4/+8
Factor our a common helper to check if a path has been disabled by something other than the per-namespace ANA state. Signed-off-by: Hannes Reinecke <hare@suse.com> [hch: split from a bigger patch] Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-05-13nvme-multipath: avoid crash on invalid subsystem cntlid enumerationHannes Reinecke1-1/+1
A process holding an open reference to a removed disk prevents it from completing deletion, so its name continues to exist. A subsequent gendisk creation may have the same cntlid which risks collision when using that for the name. Use the unique ctrl->instance instead. Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-05-01nvme-multipath: don't print ANA group state by defaultHannes Reinecke1-1/+1
Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-05-01nvme-multipath: split bios with the ns_head bio_set before submittingHannes Reinecke1-0/+8
If the bio is moved to a different queue via blk_steal_bios() and the original queue is destroyed in nvme_remove_ns() we'll be ending with a crash in bio_endio() as the mempool for the split bio bvecs had already been destroyed. So split the bio using the original queue (which will remain during the lifetime of the bio) before sending it down to the underlying device. Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-03-28nvme-multipath: relax ANA state checkMartin George1-4/+1
When undergoing state transitions I/O might be requeued, hence we should always call nvme_mpath_set_live() to schedule requeue_work whenever the nvme device is live, independent on whether the old state was live or not. Signed-off-by: Martin George <marting@netapp.com> Signed-off-by: Gargi Srinivas <sring@netapp.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-02-20nvme: convert to SPDX identifiersChristoph Hellwig1-9/+1
Update license to use SPDX-License-Identifier instead of verbose license text. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
2019-02-20nvme-multipath: round-robin I/O policyHannes Reinecke1-1/+85
Implement a simple round-robin I/O policy for multipathing. Path selection is done in two rounds, first iterating across all optimized paths, and if that doesn't return any valid paths, iterate over all optimized and non-optimized paths. If no paths are found, use the existing algorithm. Also add a sysfs attribute 'iopolicy' to switch between the current NUMA-aware I/O policy and the 'round-robin' I/O policy. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-01-23nvme-multipath: drop optimization for static ANA group IDsHannes Reinecke1-2/+1
Bit 6 in the ANACAP field is used to indicate that the ANA group ID doesn't change while the namespace is attached to the controller. There is an optimisation in the code to only allocate space for the ANA group header, as the namespace list won't change and hence would not need to be refreshed. However, this optimisation was never carried over to the actual workflow, which always assumes that the buffer is large enough to hold the ANA header _and_ the namespace list. So drop this optimisation and always allocate enough space. Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-01-09nvme-multipath: zero out ANA log bufferHannes Reinecke1-0/+2
When nvme_init_identify() fails the ANA log buffer is deallocated but _not_ set to NULL. This can cause double free oops when this controller is deleted without ever being reconnected. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-12-07nvme: add a numa_node field to struct nvme_ctrlHannes Reinecke1-2/+2
Instead of directly poking into the struct device add a new numa_node field to struct nvme_ctrl. This allows fabrics drivers where ctrl->dev is a virtual device to support NUMA affinity as well. Also expose the field as a sysfs attribute, and populate it for the RDMA and FC transports. Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-05 05:07:21 +0000