summaryrefslogtreecommitdiffstats
path: root/drivers/ntb
AgeCommit message (Collapse)AuthorFilesLines
2018-11-01ntb: idt: Alter the driver info commentsSerge Semin3-9/+8
Since IDT PCIe-switch temperature sensor is now always available irregardless of the EEPROM/BIOS settings, Kconfig and in-code description should be properly altered. In addition lets update the driver copyright lines. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-11-01ntb: idt: Discard temperature sensor IRQ handlerSerge Semin2-43/+3
IDT PCIe-switch temperature sensor interface is very broken. First of all only a few combinations of TMPCTL threshold enable bits really cause the interrupts unmasked. Even if an individual bit indicates the event unmasked, corresponding IRQ just isn't generated. Most of the threshold enable bits combinations are in fact useless and non of them can help to create a fully functional alarm interface. So to speak, we can't create a well defined hwmon alarms based on the IDT PCI-switch threshold IRQs. Secondly a single threshold IRQ (not a combination of thresholds) can be successfully enabled without the issue described above. But in this case we experienced an enormous number of interrupts generated by the chip if the temperature got near the enabled threshold value. Filter adjustment didn't help much. It also doesn't provide a hysteresis settings. Due to the temperature sample fluctuations near the threshold the interrupts spate makes the system nearly unusable until the temperature value finally settled so being pushed either to be fully higher or lower the threshold. All of these issues makes the temperature sensor alarm interface useless and even at some point dangerous to be used in the driver. In this case it is safer to completely discard it and disable the temperature alarm interrupts. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-11-01ntb: idt: Add basic hwmon sysfs interfaceSerge Semin3-1/+206
IDT PCIe switches provide an embedded temperature sensor working within [0; 127.5]C with resolution of 0.5C. They also can generate a PCIe upstream interrupt in case if the temperature passes through specified thresholds. Since this thresholds interface is very broken the created hwmon-sysfs interface exposes only the next set of hwmon nodes: current input temperature, lowest and highest values measured, history resetting, value offset. HWmon alarm interface isn't provided. IDT PCIe switch also've got an ADC/filter settings of the sensor. This driver doesn't expose them to the hwmon-sysfs interface at the moment, except the offset node. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-11-01ntb: idt: Alter temperature read methodSerge Semin2-17/+152
In order to create a hwmon interface for the IDT PCIe-switch temperature sensor the already available reader method should be improved. Particularly we need to redesign it so one would be able to read temperature/offset values from registers of the passed types. Since IDT sensor interface provides temperature in unsigned format 0:7:1 (7 bits for real value and one for fraction) we also need to have helpers for the typical sysfs temperature data type conversion to and from this format. Even though the IDT PCIe-switch provided temperature offset got the same but signed type it can be translated by these methods too. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-10-31NTB: transport: Try harder to alloc an aligned MW bufferAaron Sierra1-23/+63
Be a little wasteful if the (likely CMA) message window buffer is not suitably aligned after our first attempt; allocate a buffer twice as big as we need and manually align our MW buffer within it. This was needed on Intel Broadwell DE platforms with intel_iommu=off Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-10-31ntb: ntb_transport: Mark expected switch fall-throughsGustavo A. R. Silva1-0/+2
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 1373888 ("Missing break in switch") Addresses-Coverity-ID: 1373889 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Allen Hubbe <allenbh@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-10-31ntb: idt: Set PCIe bus address to BARLIMITxSerge Semin1-1/+1
IDT NTB driver sets the upper limit of actual translation address being written to the corresponding memory window setup. It is achieved by BARLIMITx register initialization. Needless to say, that the register works within PCIe bus address space. In general CPU and PCIe address spaces are different. It means, that addresses used for Memory TLPs routine can be different from CPU addresses. While in most of cases they are the same, there are exceptions when the proper mapping must be performed to have the portable driver code. There used to be a virt_to_bus()/bus_to_virt() interface for this purpose. But it's deprecated now. It was also a mistake to use pci_resource_start() since the return address of the method is at the CPU address space. In order to achieve the desired purpose we need to use pci_bus_address() helper. This method shall return a PCIe bus base address of the corresponding BAR resource. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Acked-by: Allen Hubbe <allenbh@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-10-31NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checksGustavo A. R. Silva1-4/+4
Both devm_kcalloc() and devm_kzalloc() return NULL on error. They never return error pointers. The use of IS_ERR_OR_NULL is currently applied to the wrong context. Fix this by replacing IS_ERR_OR_NULL with regular NULL checks. Fixes: bf2a952d31d2 ("NTB: Add IDT 89HPESxNTx PCIe-switches support") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-10-31ntb: intel: fix return value for ndev_vec_mask()Dave Jiang1-1/+1
ndev_vec_mask() should be returning u64 mask value instead of int. Otherwise the mask value returned can be incorrect for larger vectors. Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers") Signed-off-by: Dave Jiang <dave.jiang@intel.com> Tested-by: Lucas Van <lucas.van@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-06-29switchtec: Use generic PCI Vendor ID and Class CodeDoug Meyer1-1/+2
Move the Microsemi Switchtec PCI Vendor ID (same as PCI_VENDOR_ID_PMC_Sierra) to pci_ids.h. Also, replace Microsemi class constants with the standard PCI definitions. Signed-off-by: Doug Meyer <dmeyer@gigaio.com> [bhelgaas: restore SPDX (I assume it was removed by mistake), remove device ID definitions] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
2018-06-12Merge tag 'overflow-v4.18-rc1-part2' of ↵Linus Torvalds3-6/+6
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull more overflow updates from Kees Cook: "The rest of the overflow changes for v4.18-rc1. This includes the explicit overflow fixes from Silvio, further struct_size() conversions from Matthew, and a bug fix from Dan. But the bulk of it is the treewide conversions to use either the 2-factor argument allocators (e.g. kmalloc(a * b, ...) into kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a * b) into vmalloc(array_size(a, b)). Coccinelle was fighting me on several fronts, so I've done a bunch of manual whitespace updates in the patches as well. Summary: - Error path bug fix for overflow tests (Dan) - Additional struct_size() conversions (Matthew, Kees) - Explicitly reported overflow fixes (Silvio, Kees) - Add missing kvcalloc() function (Kees) - Treewide conversions of allocators to use either 2-factor argument variant when available, or array_size() and array3_size() as needed (Kees)" * tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits) treewide: Use array_size in f2fs_kvzalloc() treewide: Use array_size() in f2fs_kzalloc() treewide: Use array_size() in f2fs_kmalloc() treewide: Use array_size() in sock_kmalloc() treewide: Use array_size() in kvzalloc_node() treewide: Use array_size() in vzalloc_node() treewide: Use array_size() in vzalloc() treewide: Use array_size() in vmalloc() treewide: devm_kzalloc() -> devm_kcalloc() treewide: devm_kmalloc() -> devm_kmalloc_array() treewide: kvzalloc() -> kvcalloc() treewide: kvmalloc() -> kvmalloc_array() treewide: kzalloc_node() -> kcalloc_node() treewide: kzalloc() -> kcalloc() treewide: kmalloc() -> kmalloc_array() mm: Introduce kvcalloc() video: uvesafb: Fix integer overflow in allocation UBIFS: Fix potential integer overflow in allocation leds: Use struct_size() in allocation Convert intel uncore to struct_size ...
2018-06-12treewide: kzalloc_node() -> kcalloc_node()Kees Cook3-6/+6
The kzalloc_node() function has a 2-factor argument form, kcalloc_node(). This patch replaces cases of: kzalloc_node(a * b, gfp, node) with: kcalloc_node(a * b, gfp, node) as well as handling cases of: kzalloc_node(a * b * c, gfp, node) with: kzalloc_node(array3_size(a, b, c), gfp, node) as it's slightly less ugly than: kcalloc_node(array_size(a, b), c, gfp, node) This does, however, attempt to ignore constant size factors like: kzalloc_node(4 * 1024, gfp, node) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc_node( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc_node( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc_node( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc_node( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(char) * COUNT + COUNT , ...) | kzalloc_node( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc_node + kcalloc_node ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc_node( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc_node( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc_node( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc_node( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc_node( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc_node( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc_node( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc_node( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc_node(C1 * C2 * C3, ...) | kzalloc_node( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc_node( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc_node( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc_node( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc_node(sizeof(THING) * C2, ...) | kzalloc_node(sizeof(TYPE) * C2, ...) | kzalloc_node(C1 * C2 * C3, ...) | kzalloc_node(C1 * C2, ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc_node + kcalloc_node ( - (E1) * E2 + E1, E2 , ...) | - kzalloc_node + kcalloc_node ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc_node + kcalloc_node ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-11ntb: ntb_transport: Replace GFP_ATOMIC with GFP_KERNEL in ↵Jia-Ju Bai1-2/+2
ntb_transport_create_queue ntb_transport_create_queue() is never called in atomic context. ntb_transport_create_queue() is only called by ntb_netdev_probe(), which is set as ".probe" in struct ntb_transport_client. Despite never getting called from atomic context, ntb_transport_create_queue() calls kzalloc_node() with GFP_ATOMIC, which does not sleep for allocation. GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL, which can sleep and improve the possibility of sucessful allocation. This is found by a static analysis tool named DCNS written by myself. And I also manually check it Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-06-11ntb: ntb_transport: Replace GFP_ATOMIC with GFP_KERNEL in ↵Jia-Ju Bai1-1/+1
ntb_transport_setup_qp_mw ntb_transport_setup_qp_mw() is never called in atomic context. ntb_transport_setup_qp_mw() is only called by ntb_transport_link_work(), which is set as a parameter of INIT_DELAYED_WORK() in ntb_transport_probe(). Despite never getting called from atomic context, ntb_transport_setup_qp_mw() calls kzalloc_node() with GFP_ATOMIC, which does not sleep for allocation. GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL, which can sleep and improve the possibility of sucessful allocation. This is found by a static analysis tool named DCNS written by myself. And I also manually check it. Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-06-11NTB: ntb_hw_idt: fix typo 'can by' to 'can be'Wolfram Sang1-1/+1
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-06-11ntb: intel: change references of skx to gen3Dave Jiang4-130/+126
Change all references to skx to gen3 NTB. Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-06-11ntb: intel: split out the gen3 codeDave Jiang6-657/+754
Move the Intel hw gen3 code to its own source file. The ntb_hw_intel.c was getting too large and makes it hard to maintain with future hardware changes. Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-06-11ntb: intel: header definitions refactorDave Jiang4-142/+237
Break out the generation specific definitions to different headers Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: ntb_perf: fix cast to restricted __le32Serge Semin1-15/+13
Sparse is whining about the u32 and __le32 mixed usage in the driver drivers/ntb/test/ntb_perf.c:288:21: warning: cast to restricted __le32 drivers/ntb/test/ntb_perf.c:295:37: warning: incorrect type in argument 4 (different base types) drivers/ntb/test/ntb_perf.c:295:37: expected unsigned int [unsigned] [usertype] val drivers/ntb/test/ntb_perf.c:295:37: got restricted __le32 [usertype] <noident> ... NTB hardware drivers shall accept CPU-endian data and translate it to the portable formate by internal means, so the explicit conversions are not necessary before Scratchpad/Messages API usage anymore. Fixes: b83003b3fdc1 ("NTB: ntb_perf: Add full multi-port NTB API support") Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_perf: Fix an error code in perf_copy_chunk()Dan Carpenter1-1/+2
We accidentally return success if dmaengine_submit() fails. The fix is to preserve the error code from dma_submit_error(). Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Make function switchtec_ntb_remove() staticWei Yongjun1-2/+2
Fixes the following sparse warnings: drivers/ntb/hw/mscc/ntb_hw_switchtec.c:1552:6: warning: symbol 'switchtec_ntb_remove' was not declared. Should it be static? Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: ntb_tool: fix memory leak on 'buf' on error exit pathColin Ian King1-1/+3
Currently there is a memory leak on buf when the call to ntb_mw_get_align fails. Add an exit err label and jump to this so that kfree on buf frees the memory. Detected by CoverityScan, CID#1464286 ("Resource leak") Fixes: d637628ce00c ("NTB: ntb_tool: Add full multi-port NTB API support") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: ntb_perf: fix printing of resource_size_tArnd Bergmann1-2/+2
On 32-bit architectures, resource_size_t is usually 'unsigned int' or 'unsigned long' but not 'unsigned long long', so we get a warning about printing the wrong data: drivers/ntb/test/ntb_perf.c: In function 'perf_setup_peer_mw': drivers/ntb/test/ntb_perf.c:1390:35: error: format '%llx' expects argument of type 'long long unsigned int', but argument 4 has type 'resource_size_t {aka unsigned int}' [-Werror=format=] This changes the format string to the special %pa that is already used elsewhere in the same file. Fixes: b83003b3fdc1 ("NTB: ntb_perf: Add full multi-port NTB API support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: ntb_hw_idt: Set NTB_TOPO_SWITCH topologySerge Semin1-1/+1
Since Switchtec patch there has been a new topology added to the NTB API. It's called NTB_TOPO_SWITCH and dedicated for PCIe switch chips. Even though topo field isn't used within the IDT driver much, lets set it for the sake of unification. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: ntb_perf: Add full multi-port NTB API supportSerge Semin1-601/+1219
Former NTB Performance driver could only work with NTB devices, which got Scratchpads available and had just two ports. Since there are devices, which don't have Scratchpads and got more than two peer ports, the performance measuring tool needs to be rewritten. This patch adds the ability to test any available NTB peer. Additionally it allows to set NTB memory windows up using any available data exchange interface: Scratchpad or Message registers. Some cleanups are also added here. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: ntb_tool: Add full multi-port NTB API supportSerge Semin1-580/+1240
Former NTB Debugging tool driver supported only the limited functionality of the recently updated NTB API, which is now available to work with the truly NTB multi-port devices and devices, which got NTB Message registers instead of Scratchpads. This patch fully rewrites the driver so one would fully expose all the new NTB API interfaces. Particularly it concerns the Message registers, peer ports API, NTB link settings. Additional cleanups are also added here. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: ntb_pp: Add full multi-port NTB API supportSerge Semin1-165/+282
Current Ping Pong driver can't truly work with multi-port devices. Additionally it requires the Scratchpad registers being available on NTB device. This patches rewrites the driver so one would perform the cyclic Ping-Pong algorithm around all the available NTB peers and makes it working with NTB hardware, which doesn't support Scratchpads, but such alternative as NTB Message register. Additional cleanups are also added here. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: Set dma mask and dma coherent mask to NTB devicesSerge Semin4-2/+15
The dma_mask and dma_coherent_mask fields of the NTB struct device weren't initialized in hardware drivers. In fact it should be done instead of PCIe interface usage, since NTB clients are supposed to use NTB API and left unaware of real hardware implementation. In addition to that ntb_device_register() method shouldn't clear the passed ntb_dev structure, since it dma_mask is initialized by hardware drivers. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: Rename NTB messaging API methodsSerge Semin1-15/+12
There is a common methods signature form used over all the NTB API like functions naming scheme, arguments names and order, etc. Recently added NTB messaging API IO callbacks were named a bit different so should be renamed to be in compliance with the rest of the API. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: fix logic errorArnd Bergmann1-1/+1
Newer gcc (version 7 and 8 presumably) warn about a statement mixing the << operator with logical and: drivers/ntb/hw/mscc/ntb_hw_switchtec.c: In function 'switchtec_ntb_init_sndev': drivers/ntb/hw/mscc/ntb_hw_switchtec.c:888:24: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context] My interpretation here is that the author must have intended a bitmask rather than a comparison, so I'm changing the '&&' to '&', which makes a lot more sense in the context. Fixes: 1b249475275d ("ntb_hw_switchtec: Allow using Switchtec NTB in multi-partition setups") Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Check for alignment of the buffer in mw_set_trans()Logan Gunthorpe1-0/+13
With Switchtec hardware, the buffer used for a memory window must be aligned to its size (the hardware only replaces the lower bits). In certain circumstances dma_alloc_coherent() will not provide a buffer that adheres to this requirement like when using the CMA and CONFIG_CMA_ALIGNMENT is set lower than the buffer size. When we get an unaligned buffer mw_set_trans() should return an error. We also log an error so we know the cause of the problem. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_transport: Fix bug with max_mw_size parameterLogan Gunthorpe1-0/+3
When using the max_mw_size parameter of ntb_transport to limit the size of the Memory windows, communication cannot be established and the queues freeze. This is because the mw_size that's reported to the peer is correctly limited but the size used locally is not. So the MW is initialized with a buffer smaller than the window but the TX side is using the full window. This means the TX side will be writing to a region of the window that points nowhere. This is easily fixed by applying the same limit to tx_size in ntb_transport_init_queue(). Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers") Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Cc: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Force down the link before initializingLogan Gunthorpe1-7/+50
If one host crashes and soft reboots, the other host may not see a link down event. Then when the crashed host comes back up, the surviving host may not know the link was reset and the NTB clients may not work without being reset. To solve this, we send a LINK_FORCE_DOWN message to each peer every time we come up, before we register the NTB device. If a surviving host still thinks the link is up it will take it down immediately. In this way, once the crashed host comes up fully, it will send a regular link up event as per usual and the link will be properly restarted. While we are in the area, this also fixes the MSG_LINK_UP message that was in the link down function that was reported by Doug Meyers. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reported-by: ThanhTuThai <cruisethai@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Crosslink doorbells and messagesLogan Gunthorpe1-10/+55
In a crosslink configuration doorbells and messages largely work the same but the NTB registers must be accessed through the reserved LUT window. Also, as a bonus, seeing there are now two independent sets of NTB links, both partitions can actually use all 60 doorbell registers instead of them having to be split into two for each partition. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Add initialization code for crosslinkLogan Gunthorpe1-5/+197
Crosslink is a feature of the Switchtec switches that is similar to the B2B mode of other NTB devices. It allows a system to be designed that is perfectly symmetric with two identical switches that link two hosts together. In order for the system to be symmetric, there is an empty host-less partition between the two switches which the host must enumerate and assign BAR addresses to. The firmware in the switch manages this specially so that the BAR addresses on both sides of the empty partition will be identical despite being in the same partition with the same address space. The driver determines whether crosslink is enabled by a flag set in the NTB partition info registers which are set by the switch's configuration file. When crosslink is enabled, a reserved LUT window is setup to point to the peer's switch's NTB registers and the local MWs are set to forward to the host-less partition's BARs. (Yes, this hurts my brain too.) Once this is setup, largely the same NTB infrastructure is used to communicate between the two hosts. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Make switchtec_ntb_init_req_id_table() more generalLogan Gunthorpe1-36/+56
This is a prep patch in order to support the crosslink feature which will require the driver to setup the requester ID table in another partition as well as it's own. To aid this, create a helper function which sets up the requester IDs from an array. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Create helper function to setup reserved LUT MWsLogan Gunthorpe1-29/+43
This is a prep patch in order to support the crosslink feature which will require the driver to use another reserved LUT window. To simplify this we move the code which sets up the reserved LUT window into a helper function which will be used by the crosslink initialization. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Keep track of the number of LUT windows used by the driverLogan Gunthorpe1-4/+8
This is a prep patch in order to support the crosslink feature which will require the driver to use another reserved LUT window. To simplify this, we add some code to track the number of reserved LUT windows in use instead of assuming this is always 1. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb_hw_switchtec: Allow using Switchtec NTB in multi-partition setupsKelvin Cao1-9/+48
Allow using Switchtec NTB in setups that have more than two partitions. Note: this does not enable having multi-host communication, it only allows for a single NTB link between two hosts in a network that might have more than two. Use following logic to determine the NT peer partition: 1) If there are 2 partitions, and the target vector is set in the Switchtec configuration, use the partition specified in target vector. 2) If there are 2 partitions and target vector is unset use the only other partition as specified in the NT EP map. 3) If there are more than 2 partitions and target vector is set use the other partition specified in target vector. 4) If there are more than 2 partitions and target vector is unset, this is invalid and report an error. Signed-off-by: Kelvin Cao <kelvin.cao@microsemi.com> [logang@deltatee.com: commit message fleshed out] Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: switchtec_ntb: Add new line on appropriate printksJon Mason1-21/+21
Trivial addition of "\n" to the dev_* prints where necessary Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: switchtec_ntb: fix spelling mistake: "peforming" -> "performing"Colin Ian King1-1/+1
Trivial fix to spelling mistake in dev_err error message Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-By: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb: remove Intel Atom NTB driver supportDave Jiang2-363/+4
Removing dead code since this is not being used. Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28ntb: remove unneeded DRIVER_LICENSE #definesGreg Kroah-Hartman4-8/+4
There is no need to #define the license of the driver, just put it in the MODULE_LICENSE() line directly as a text string. This allows tools that check that the module license matches the source code license to work properly, as there is no need to unwind the unneeded dereference, especially when the string is defined just a few lines above the usage of it. Reported-and-reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Dave Jiang <dave.jiang@intel.com> Cc: Allen Hubbe <Allen.Hubbe@emc.com> Cc: Gary R Hook <gary.hook@amd.com> Cc: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28NTB: ntb_hw_switchtec: Fix peer BAR bug in switchtec_ntb_init_shared_mwDoug Meyer1-4/+5
This resolves a bug which may incorrectly configure the peer host's LUT for shared memory window access. The code was using the local host's first BAR number, rather than the peer hosts's first BAR number, to determine what peer NT control register to program. The bug will cause the Switchtec NTB link to work only if both peers have the same first NTB BAR configured. In all other configurations, the link will not come up, failing silently. When both hosts have the same first BAR, the configuration works only because the first BAR numbers happent to be the same. When the hosts do not have the same first BAR, then the LUT translation will not be configured in the correct peer LUT and will not give the peer the shared memory window access required for the link to operate. Signed-off-by: Doug Meyer <dmeyer@gigaio.com> Reviewed-by: Logan Gunthorpe <logang@deltatee.com> Fixes: 678784a44ae8 ("NTB: switchtec_ntb: Initialize hardware for memory windows") Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-21treewide: setup_timer() -> timer_setup()Kees Cook1-4/+4
This converts all remaining cases of the old setup_timer() API into using timer_setup(), where the callback argument is the structure already holding the struct timer_list. These should have no behavioral changes, since they just change which pointer is passed into the callback with the same available pointers after conversion. It handles the following examples, in addition to some other variations. Casting from unsigned long: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... setup_timer(&ptr->my_timer, my_callback, ptr); and forced object casts: void my_callback(struct something *ptr) { ... } ... setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr); become: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... timer_setup(&ptr->my_timer, my_callback, 0); Direct function assignments: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... ptr->my_timer.function = my_callback; have a temporary cast added, along with converting the args: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback; And finally, callbacks without a data assignment: void my_callback(unsigned long data) { ... } ... setup_timer(&ptr->my_timer, my_callback, 0); have their argument renamed to verify they're unused during conversion: void my_callback(struct timer_list *unused) { ... } ... timer_setup(&ptr->my_timer, my_callback, 0); The conversion is done with the following Coccinelle script: spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup.cocci @fix_address_of@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_timer, NULL, _E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E->_timer, NULL, (_cast_data)_E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E._timer, NULL, &_E); +timer_setup(&_E._timer, NULL, 0); | -setup_timer(&_E._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_timer, _callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | _E->_timer@_stl.function = _callback; | _E->_timer@_stl.function = &_callback; | _E->_timer@_stl.function = (_cast_func)_callback; | _E->_timer@_stl.function = (_cast_func)&_callback; | _E._timer@_stl.function = _callback; | _E._timer@_stl.function = &_callback; | _E._timer@_stl.function = (_cast_func)_callback; | _E._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_timer, _callback, 0); +setup_timer(&_E->_timer, _callback, (_cast_data)_E); | -timer_setup(&_E._timer, _callback, 0); +setup_timer(&_E._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_timer | -(_cast_data)&_E +&_E._timer | -_E +&_E->_timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_timer, _callback, 0); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0L); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0UL); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0L); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0UL); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_timer, _callback, 0); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0L); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0UL); +timer_setup(&_timer, _callback, 0); | -setup_timer(_timer, _callback, 0); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0L); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0UL); +timer_setup(_timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-18ntb: intel: remove b2b memory window workaround for Skylake NTBDave Jiang1-73/+2
The workaround code is never used because Skylake NTB does not need it. Reported-by: Allen Hubbe <allen.hubbe@dell.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18NTB: make idt_89hpes_cfg constBhumika Goyal1-8/+8
Make these const as they are only used during a copy operation. Done using Coccinelle. Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18NTB: switchtec_ntb: Add memory window supportLogan Gunthorpe1-3/+210
The Switchtec hardware has two types of memory windows: LUTs and Direct. The first area in each BAR is for LUT windows and the remaining area is for the direct region. The total number of LUT entries is set by a configuration setting in hardware and they all must be the same size. (This is fixed by switchtec_ntb to be 64K.) switchtec_ntb enables the LUTs only for the first BAR and enables the highest power of two possible. Seeing the LUTs are at the beginning of the BAR, the direct memory window's alignment is affected. Therefore, the maximum direct memory window size can not be greater than the number of LUTs times 64K. The direct window in other BARs will not have this restriction as the LUTs will not be enabled there. LUTs will only be exposed through the NTB API if the use_lut_mw parameter is set. Seeing the Switchtec hardware, by default, configures BARs to be 4G a module parameter is given to limit the size of the advertised memory windows. Higher layers tend to allocate the maximum BAR size and this has a tendency to fail when they try to allocate 4GB of contiguous memory. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Stephen Bates <sbates@raithlin.com> Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com> Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18NTB: switchtec_ntb: Implement scratchpad registersLogan Gunthorpe1-2/+73
Seeing there is no dedicated hardware for this, we simply add these as entries in the shared memory window. Thus, we could support any number of them but 128 seems like enough, for now. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Stephen Bates <sbates@raithlin.com> Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com> Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18NTB: switchtec_ntb: Implement doorbell registersLogan Gunthorpe1-4/+85
Pretty straightforward implementation of doorbell registers. The shift and mask were setup in an earlier patch and this just hooks up the appropriate portion of the IDB register as the local doorbells and the opposite portion of ODB as the peer doorbells. The DB mask is protected by a spinlock to avoid concurrent read-modify-write accesses. Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Stephen Bates <sbates@raithlin.com> Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com> Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-23 03:30:03 +0000