| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When using MII/GMII/SGMII in the Altera SoC, the phy needs to be
wired through the FPGA. To ensure correct behavior, the appropriate
bit in the System Manager FPGA Interface Group register needs to be
set.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Junote Cai reported that he was not able to get a DSA setup involving the
Freescale DPAA/FMAN driver to work and narrowed it down to
of_find_net_device_by_node(). This function requires the network device's
device reference to be correctly set which is the case here, though we have
lost any device_node association there.
The problem is that dpaa_eth_add_device() allocates a "dpaa-ethernet" platform
device, and later on dpaa_eth_probe() is called but SET_NETDEV_DEV() won't be
propagating &pdev->dev.of_node properly. Fix this by inherenting both the parent
device and the of_node when dpaa_eth_add_device() creates the platform device.
Fixes: 3933961682a3 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Priit reported that stmmac was crashing with the trace below. This is because
phy_attached_print() is called too early right after the PHY device has been
found, but before it has a driver attached, since that is only done in
phy_probe() which occurs later.
Fix this by dealing with a possibly NULL phydev->drv point since that can
happen here, but could also happen if we voluntarily did an unbind of the
PHY device with the PHY driver.
sun7i-dwmac 1c50000.ethernet: PTP uses main clock
sun7i-dwmac 1c50000.ethernet: no reset control found
sun7i-dwmac 1c50000.ethernet: no regulator found
sun7i-dwmac 1c50000.ethernet: Ring mode enabled
sun7i-dwmac 1c50000.ethernet: DMA HW capability register supported
sun7i-dwmac 1c50000.ethernet: Normal descriptors
libphy: stmmac: probed
Unable to handle kernel NULL pointer dereference at virtual address 00000048
pgd = c0004000
[00000048] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.13.0-rc6-00318-g0065bd7fa384 #1
Hardware name: Allwinner sun7i (A20) Family
task: ee868000 task.stack: ee85c000
PC is at phy_attached_print+0x1c/0x8c
LR is at stmmac_mdio_register+0x12c/0x200
pc : [<c04510ac>] lr : [<c045e6b4>] psr: 60000013
sp : ee85ddc8 ip : 00000000 fp : c07dfb5c
r10: ee981210 r9 : 00000001 r8 : eea73000
r7 : eeaa6dd0 r6 : eeb49800 r5 : 00000000 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : eeb49800
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 4000406a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xee85c210)
Stack: (0xee85ddc8 to 0xee85e000)
ddc0: 00000000 00000002 eeb49400 eea72000 00000000 eeb49400
dde0: c045e6b4 00000000 ffffffff eeab0810 00000000 c08051f8 ee9292c0 c016d480
de00: eea725c0 eea73000 eea72000 00000001 eea726c0 c0457d0c 00000040 00000020
de20: 00000000 c045b850 00000001 00000000 ee981200 eeab0810 eeaa6ed0 ee981210
de40: 00000000 c094a4a0 00000000 c0465180 eeaa7550 f08d0000 c9ffb90c 00000032
de60: fffffffa 00000032 ee981210 ffffffed c0a46620 fffffdfb c0a46620 c03f7be8
de80: ee981210 c0a9a388 00000000 00000000 c0a46620 c03f63e0 ee981210 c0a46620
dea0: ee981244 00000000 00000007 000000c6 c094a4a0 c03f6534 00000000 c0a46620
dec0: c03f6490 c03f49ec ee828a58 ee9217b4 c0a46620 eeaa4b00 c0a43230 c03f59fc
dee0: c08051f8 c094a49c c0a46620 c0a46620 00000000 c091c668 c093783c c03f6dfc
df00: ffffe000 00000000 c091c668 c010177c eefe0938 eefe0935 c085e200 000000c6
df20: 00000005 c0136bc8 60000013 c080b3a4 00000006 00000006 c07ce7b4 00000000
df40: c07d7ddc c07cef28 eefe0938 eefe093e c0a0b2f0 c0a641c0 c0a641c0 c0a641c0
df60: c0937834 00000007 000000c6 c094a4a0 00000000 c0900d88 00000006 00000006
df80: 00000000 c09005a8 00000000 c060ecf4 00000000 00000000 00000000 00000000
dfa0: 00000000 c060ecfc 00000000 c0107738 00000000 00000000 00000000 00000000
dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffdeffff ffffffff
[<c04510ac>] (phy_attached_print) from [<c045e6b4>] (stmmac_mdio_register+0x12c/0x200)
[<c045e6b4>] (stmmac_mdio_register) from [<c045b850>] (stmmac_dvr_probe+0x850/0x96c)
[<c045b850>] (stmmac_dvr_probe) from [<c0465180>] (sun7i_gmac_probe+0x120/0x180)
[<c0465180>] (sun7i_gmac_probe) from [<c03f7be8>] (platform_drv_probe+0x50/0xac)
[<c03f7be8>] (platform_drv_probe) from [<c03f63e0>] (driver_probe_device+0x234/0x2e4)
[<c03f63e0>] (driver_probe_device) from [<c03f6534>] (__driver_attach+0xa4/0xa8)
[<c03f6534>] (__driver_attach) from [<c03f49ec>] (bus_for_each_dev+0x4c/0x9c)
[<c03f49ec>] (bus_for_each_dev) from [<c03f59fc>] (bus_add_driver+0x190/0x214)
[<c03f59fc>] (bus_add_driver) from [<c03f6dfc>] (driver_register+0x78/0xf4)
[<c03f6dfc>] (driver_register) from [<c010177c>] (do_one_initcall+0x44/0x168)
[<c010177c>] (do_one_initcall) from [<c0900d88>] (kernel_init_freeable+0x144/0x1d0)
[<c0900d88>] (kernel_init_freeable) from [<c060ecfc>] (kernel_init+0x8/0x110)
[<c060ecfc>] (kernel_init) from [<c0107738>] (ret_from_fork+0x14/0x3c)
Code: e59021c8 e59d401c e590302c e3540000 (e5922048)
---[ end trace 39ae87c7923562d0 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Tested-By: Priit Laes <plaes@plaes.org>
Fixes: fbca164776e4 ("net: stmmac: Use the right logging function in stmmac_mdio_register")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This helps tools such as wpa_supplicant can start even if the macsec
module isn't loaded yet.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the value of the mrouter flag in struct mlxsw_sp_bridge_port when
it is being changed.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_napi_del() should be paired with netif_napi_add(), however no
such call takes place in ftgmac100_probe(). This triggers a NULL
pointer dereference if e.g. no PHY is found by the MDIO probe:
[ 2.770000] libphy: Fixed MDIO Bus: probed
[ 2.770000] ftgmac100 1e660000.ethernet: Generated random MAC address 66:58:c0:5a:50:b8
[ 2.790000] libphy: ftgmac100_mdio: probed
[ 2.790000] ftgmac100 1e660000.ethernet (unnamed net_device) (uninitialized): eth%d: no PHY found
[ 2.790000] ftgmac100 1e660000.ethernet: MII Probe failed!
[ 2.810000] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 2.810000] pgd = 80004000
[ 2.810000] [00000004] *pgd=00000000
[ 2.810000] Internal error: Oops: 805 [#1] ARM
[ 2.810000] CPU: 0 PID: 1 Comm: swapper Not tainted 4.10.17-1a4df30c39cf5ee0e3d2528c409787ccbb4a672a #1
[ 2.810000] Hardware name: ASpeed SoC
[ 2.810000] task: 9e421b60 task.stack: 9e4a0000
[ 2.810000] PC is at netif_napi_del+0x74/0xa4
[ 2.810000] LR is at ftgmac100_probe+0x290/0x674
[ 2.810000] pc : [<80331004>] lr : [<80292b30>] psr: 60000013
[ 2.810000] sp : 9e4a1d70 ip : 9e4a1d88 fp : 9e4a1d84
[ 2.810000] r10: 9e565000 r9 : ffffffed r8 : 00000007
[ 2.810000] r7 : 9e565480 r6 : 9ec072c0 r5 : 00000000 r4 : 9e5654d8
[ 2.810000] r3 : 9e565530 r2 : 00000000 r1 : 00000000 r0 : 9e5654d8
[ 2.810000] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 2.810000] Control: 00c5387d Table: 80004008 DAC: 00000055
[ 2.810000] Process swapper (pid: 1, stack limit = 0x9e4a0188)
[ 2.810000] Stack: (0x9e4a1d70 to 0x9e4a2000)
[ 2.810000] 1d60: 9e565000 9e549e10 9e4a1dcc 9e4a1d88
[ 2.810000] 1d80: 80292b30 80330f9c ffffffff 9e4a1d98 80146058 9ec072c0 00009e10 00000000
[ 2.810000] 1da0: 9e549e18 9e549e10 ffffffed 805f81f4 fffffdfb 00000000 00000000 00000000
[ 2.810000] 1dc0: 9e4a1dec 9e4a1dd0 80243df8 802928ac 9e549e10 8062cbd8 8062cbe0 805f81f4
[ 2.810000] 1de0: 9e4a1e24 9e4a1df0 80242178 80243da4 803001d0 802ffa60 9e4a1e24 9e549e10
[ 2.810000] 1e00: 9e549e44 805f81f4 00000000 00000000 805b8840 8058a6b0 9e4a1e44 9e4a1e28
[ 2.810000] 1e20: 80242434 80241f04 00000000 805f81f4 80242344 00000000 9e4a1e6c 9e4a1e48
[ 2.810000] 1e40: 80240148 80242350 9e425bac 9e4fdc90 9e790e94 805f81f4 9e790e60 805f5640
[ 2.810000] 1e60: 9e4a1e7c 9e4a1e70 802425dc 802400d8 9e4a1ea4 9e4a1e80 80240ba8 802425c0
[ 2.810000] 1e80: 8050b6ac 9e4a1e90 805f81f4 ffffe000 805b8838 80616720 9e4a1ebc 9e4a1ea8
[ 2.810000] 1ea0: 80243068 80240a68 805ab24c ffffe000 9e4a1ecc 9e4a1ec0 80244a38 80242fec
[ 2.810000] 1ec0: 9e4a1edc 9e4a1ed0 805ab264 80244a04 9e4a1f4c 9e4a1ee0 8058ae70 805ab258
[ 2.810000] 1ee0: 80032c68 801e3fd8 8052f800 8041af2c 9e4a1f4c 9e4a1f00 80032f90 8058a6bc
[ 2.810000] 1f00: 9e4a1f2c 9e4a1f10 00000006 00000006 00000000 8052f220 805112f0 00000000
[ 2.810000] 1f20: 9e4a1f4c 00000006 80616720 805cf400 80616720 805b8838 80616720 00000057
[ 2.810000] 1f40: 9e4a1f94 9e4a1f50 8058b040 8058add0 00000006 00000006 00000000 8058a6b0
[ 2.810000] 1f60: 3940bf3d 00000007 f115c2e8 00000000 803fd158 00000000 00000000 00000000
[ 2.810000] 1f80: 00000000 00000000 9e4a1fac 9e4a1f98 803fd170 8058af38 00000000 803fd158
[ 2.810000] 1fa0: 00000000 9e4a1fb0 8000a5e8 803fd164 00000000 00000000 00000000 00000000
[ 2.810000] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.810000] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 d11dcae8 af8ddec5
[ 2.810000] [<80331004>] (netif_napi_del) from [<80292b30>] (ftgmac100_probe+0x290/0x674)
[ 2.810000] [<80292b30>] (ftgmac100_probe) from [<80243df8>] (platform_drv_probe+0x60/0xc0)
[ 2.810000] [<80243df8>] (platform_drv_probe) from [<80242178>] (driver_probe_device+0x280/0x44c)
[ 2.810000] [<80242178>] (driver_probe_device) from [<80242434>] (__driver_attach+0xf0/0x104)
[ 2.810000] [<80242434>] (__driver_attach) from [<80240148>] (bus_for_each_dev+0x7c/0xb0)
[ 2.810000] [<80240148>] (bus_for_each_dev) from [<802425dc>] (driver_attach+0x28/0x30)
[ 2.810000] [<802425dc>] (driver_attach) from [<80240ba8>] (bus_add_driver+0x14c/0x268)
[ 2.810000] [<80240ba8>] (bus_add_driver) from [<80243068>] (driver_register+0x88/0x104)
[ 2.810000] [<80243068>] (driver_register) from [<80244a38>] (__platform_driver_register+0x40/0x54)
[ 2.810000] [<80244a38>] (__platform_driver_register) from [<805ab264>] (ftgmac100_driver_init+0x18/0x20)
[ 2.810000] [<805ab264>] (ftgmac100_driver_init) from [<8058ae70>] (do_one_initcall+0xac/0x168)
[ 2.810000] [<8058ae70>] (do_one_initcall) from [<8058b040>] (kernel_init_freeable+0x114/0x1cc)
[ 2.810000] [<8058b040>] (kernel_init_freeable) from [<803fd170>] (kernel_init+0x18/0x104)
[ 2.810000] [<803fd170>] (kernel_init) from [<8000a5e8>] (ret_from_fork+0x14/0x2c)
[ 2.810000] Code: e594205c e5941058 e2843058 e3a05000 (e5812004)
[ 3.210000] ---[ end trace f32811052fd3860c ]---
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enable_4k_uar module parameter was added in patch cited below to
address the backward compatibility issue in SRIOV when the VM has
system's PAGE_SIZE uar implementation and the Hypervisor has 4k uar
implementation.
The above compatibility issue does not exist in the non SRIOV case.
In this patch, we always enable 4k uar implementation if SRIOV
is not enabled on mlx4's supported cards.
Fixes: 76e39ccf9c36 ("net/mlx4_core: Fix backward compatibility on VFs")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzkaller reported a double free [1], caused by the fact
that tun driver was not updated properly when priv_destructor
was added.
When/if register_netdevice() fails, priv_destructor() must have been
called already.
[1]
BUG: KASAN: double-free or invalid-free in selinux_tun_dev_free_security+0x15/0x20 security/selinux/hooks.c:5023
CPU: 0 PID: 2919 Comm: syzkaller227220 Not tainted 4.13.0-rc4+ #23
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
print_address_description+0x7f/0x260 mm/kasan/report.c:252
kasan_report_double_free+0x55/0x80 mm/kasan/report.c:333
kasan_slab_free+0xa0/0xc0 mm/kasan/kasan.c:514
__cache_free mm/slab.c:3503 [inline]
kfree+0xd3/0x260 mm/slab.c:3820
selinux_tun_dev_free_security+0x15/0x20 security/selinux/hooks.c:5023
security_tun_dev_free_security+0x48/0x80 security/security.c:1512
tun_set_iff drivers/net/tun.c:1884 [inline]
__tun_chr_ioctl+0x2ce6/0x3d50 drivers/net/tun.c:2064
tun_chr_ioctl+0x2a/0x40 drivers/net/tun.c:2309
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x443ff9
RSP: 002b:00007ffc34271f68 EFLAGS: 00000217 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00000000004002e0 RCX: 0000000000443ff9
RDX: 0000000020533000 RSI: 00000000400454ca RDI: 0000000000000003
RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000217 R12: 0000000000401ce0
R13: 0000000000401d70 R14: 0000000000000000 R15: 0000000000000000
Allocated by task 2919:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_kmalloc+0xaa/0xd0 mm/kasan/kasan.c:551
kmem_cache_alloc_trace+0x101/0x6f0 mm/slab.c:3627
kmalloc include/linux/slab.h:493 [inline]
kzalloc include/linux/slab.h:666 [inline]
selinux_tun_dev_alloc_security+0x49/0x170 security/selinux/hooks.c:5012
security_tun_dev_alloc_security+0x6d/0xa0 security/security.c:1506
tun_set_iff drivers/net/tun.c:1839 [inline]
__tun_chr_ioctl+0x1730/0x3d50 drivers/net/tun.c:2064
tun_chr_ioctl+0x2a/0x40 drivers/net/tun.c:2309
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
Freed by task 2919:
save_stack_trace+0x16/0x20 arch/x86/kernel/stacktrace.c:59
save_stack+0x43/0xd0 mm/kasan/kasan.c:447
set_track mm/kasan/kasan.c:459 [inline]
kasan_slab_free+0x6e/0xc0 mm/kasan/kasan.c:524
__cache_free mm/slab.c:3503 [inline]
kfree+0xd3/0x260 mm/slab.c:3820
selinux_tun_dev_free_security+0x15/0x20 security/selinux/hooks.c:5023
security_tun_dev_free_security+0x48/0x80 security/security.c:1512
tun_free_netdev+0x13b/0x1b0 drivers/net/tun.c:1563
register_netdevice+0x8d0/0xee0 net/core/dev.c:7605
tun_set_iff drivers/net/tun.c:1859 [inline]
__tun_chr_ioctl+0x1caf/0x3d50 drivers/net/tun.c:2064
tun_chr_ioctl+0x2a/0x40 drivers/net/tun.c:2309
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
The buggy address belongs to the object at ffff8801d2843b40
which belongs to the cache kmalloc-32 of size 32
The buggy address is located 0 bytes inside of
32-byte region [ffff8801d2843b40, ffff8801d2843b60)
The buggy address belongs to the page:
page:ffffea000660cea8 count:1 mapcount:0 mapping:ffff8801d2843000 index:0xffff8801d2843fc1
flags: 0x200000000000100(slab)
raw: 0200000000000100 ffff8801d2843000 ffff8801d2843fc1 000000010000003f
raw: ffffea0006626a40 ffffea00066141a0 ffff8801dbc00100
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8801d2843a00: fb fb fb fb fc fc fc fc fb fb fb fb fc fc fc fc
ffff8801d2843a80: 00 00 00 fc fc fc fc fc fb fb fb fb fc fc fc fc
>ffff8801d2843b00: 00 00 00 00 fc fc fc fc fb fb fb fb fc fc fc fc
^
ffff8801d2843b80: fb fb fb fb fc fc fc fc fb fb fb fb fc fc fc fc
ffff8801d2843c00: fb fb fb fb fc fc fc fc fb fb fb fb fc fc fc fc
==================================================================
Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The loop counter k is currently being decremented from zero which
is incorrect. Fix this by incrementing k instead
Detected by CoverityScan, CID#401847 ("Infinite loop")
Fixes: 83f18a557c6d ("netxen_nic: fw dump support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The while loop that performs the dma page unmapping never decrements
index counter f and hence loops forever. Fix this with a pre-decrement
on f.
Detected by CoverityScan, CID#1357309 ("Infinite loop")
Fixes: 4c3523623dc0 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC stats command takes a port ID, which doesn't exist on
pre-ef10 NICs (5000- and 6000- series). This is extracted from the
NIC specific data; we misinterpret this as the ef10 data structure,
causing us to read potentially unallocated data. With a KASAN kernel
this can cause errors with:
BUG: KASAN: slab-out-of-bounds in efx_mcdi_mac_stats
Fixes: 0a2ab4d988d7 ("sfc: set the port-id when calling MC_CMD_MAC_STATS")
Reported-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb4vf Ethernet driver now queries PCIe configuration space to
determine if it can send TLPs to it with the Relaxed Ordering
Attribute set, just like the pf did.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb4 Ethernet driver now queries PCIe configuration space to determine
if it can send TLPs to it with the Relaxed Ordering Attribute set.
Remove the enable_pcie_relaxed_ordering() to avoid enable PCIe Capability
Device Control[Relaxed Ordering Enable] at probe routine, to make sure
the driver will not send the Relaxed Ordering TLPs to the Root Complex which
could not deal the Relaxed Ordering TLPs.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware feature check introduced for multi-scheduled scan turned out
to be failing for bcm4343{0,1,8} devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Fixes: 9fe929aaace6 ("brcmfmac: add firmware feature detection for gscan feature")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
bond_miimon_commit() handles the UP transition for each slave of a bond
in the case of MII. It is triggered 10 times per second for the default
MII Polling interval of 100ms. For device drivers that do not implement
__ethtool_get_link_ksettings() the call to bond_update_speed_duplex()
fails persistently while the MII status could remain UP. That is, in
this and other cases where the speed/duplex update keeps failing over a
longer period of time while the MII state is UP, a warning is printed
every MII polling interval.
To address these excessive warnings net_ratelimit() should be used.
Printing a warning once would not be sufficient since the call to
bond_update_speed_duplex() could recover to succeed and fail again
later. In that case there would be no new indication what went wrong.
Fixes: b5bf0f5b16b9c (bonding: correctly update link status during mii-commit phase)
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Flower app may receive a request to update the MTU of a representor
netdev upon receipt of a control message from the firmware. This requires
the RTNL lock which needs to be taken outside of the packet processing
path.
As a handling of this correctly seems a little to invasive for a fix simply
skip setting the MTU for now.
Relevant backtrace:
[ 1496.288489] BUG: scheduling while atomic: kworker/0:3/373/0x00000100
[ 1496.294911] dca syscopyarea sysfillrect sysimgblt fb_sys_fops ptp drm mxm_wmi ahci pps_core libahci i2c_algo_bit wmi [last unloaded: nfp]
[ 1496.294918] CPU: 0 PID: 373 Comm: kworker/0:3 Tainted: G OE 4.13.0-rc3+ #3
[ 1496.294919] Hardware name: Supermicro X10DRi/X10DRi, BIOS 2.0 12/28/2015
[ 1496.294923] Workqueue: events work_for_cpu_fn
[ 1496.294924] Call Trace:
[ 1496.294927] <IRQ>
[ 1496.294931] dump_stack+0x63/0x82
[ 1496.294935] __schedule_bug+0x54/0x70
[ 1496.294937] __schedule+0x62f/0x890
[ 1496.294941] ? intel_unmap_sg+0x90/0x90
[ 1496.294942] schedule+0x36/0x80
[ 1496.294943] schedule_preempt_disabled+0xe/0x10
[ 1496.294945] __mutex_lock.isra.2+0x445/0x4a0
[ 1496.294947] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294950] ? kfree+0x162/0x170
[ 1496.294952] ? device_is_rmrr_locked+0x12/0x50
[ 1496.294953] ? iommu_should_identity_map+0x50/0xe0
[ 1496.294954] __mutex_lock_slowpath+0x13/0x20
[ 1496.294955] ? iommu_no_mapping+0x48/0xd0
[ 1496.294956] ? __mutex_lock_slowpath+0x13/0x20
[ 1496.294957] mutex_lock+0x2f/0x40
[ 1496.294960] rtnl_lock+0x15/0x20
[ 1496.294979] nfp_flower_cmsg_rx+0xc8/0x150 [nfp]
[ 1496.294986] nfp_ctrl_poll+0x286/0x350 [nfp]
[ 1496.294989] tasklet_action+0xf6/0x110
[ 1496.294992] __do_softirq+0xed/0x278
[ 1496.294993] irq_exit+0xb6/0xc0
[ 1496.294994] do_IRQ+0x4f/0xd0
[ 1496.294996] common_interrupt+0x89/0x89
Fixes: 948faa46c05b ("nfp: add support for control messages for flower app")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the function stmmac_mdio_register() is only used by
stmmac_dvr_probe() from stmmac_main.c, in order to register the MDIO bus
and probe information about the PHY. As this function is called before
calling register_netdev(), all messages logged from stmmac_mdio_register
are prefixed by "(unnamed net_device)". The goal of netdev_info or
netdev_err is to dump useful infos about a net_device, when this data
structure is partially initialized, there is no point for using these
functions.
This commit fixes the issue by replacing all netdev_*() by the
corresponding dev_*() function for logging. The last netdev_info is
replaced by phy_attached_info(), as a valid phydev can be used at this
point.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch c4adfc822bf5 ("bonding: make speed, duplex setting consistent
with link state") puts the link state to down if
bond_update_speed_duplex() cannot retrieve speed and duplex settings.
Assumably the patch was written with 802.3ad mode in mind which relies
on link speed/duplex settings. For other modes like active-backup these
settings are not required. Thus, only for these other modes, this patch
reintroduces support for slaves that do not support reporting speed or
duplex such as wireless devices. This fixes the regression reported in
bug 196547 (https://bugzilla.kernel.org/show_bug.cgi?id=196547).
Fixes: c4adfc822bf5 ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Geneve's Virtual Network Identifier (VNI) is 24 bit long, so the range
of values for it would be from 0 to 16777215 (2^24 -1). However, one
cannot create a geneve device with VNI set to 16777215. This patch fixes
this issue.
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With SYSTEMPORT Lite we have holes in our statistics layout that make us
skip over the hardware MIB counters, bcm_sysport_get_stats() was not
taking that into account resulting in reporting 0 for all SW-maintained
statistics, fix this by skipping accordingly.
Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an RX block-ack session times out, the firmware, which offloads
RX reordering but not the BA session negotiation, stops the session
but doesn't send a DELBA. This causes the the session to remain
active in the remote device, so no more BA sessions will be
established, causing a severe throughput degradation due to the lack
of aggregation.
Use the new ieee80211_rx_ba_timer_expired API when the ba session timer
expires, since this will tear down the ba session and also send a delba.
The previous API used is intended for drivers that offload the
addba/delba negotiation, but not the rx reordering, while our driver
does the opposite.
This patch depends on "mac80211: add api to start ba session timer
expired flow".
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we start an Rx A-MPDU session, we first get the AddBA
request, then we send an ADD_STA command to the firmware
that will reply with a BAID which is a hardware resource
that tracks the BA session.
This BAID will appear on each and every frame that we get
from the firwmare until the A-MPDU session is torn down.
In the Rx path, we look at this BAID to manage the
reordering buffer.
This flow is inherently racy since the hardware will start
to put the BAID in the frames it receives even if the
firmware hasn't sent the response to the ADD_STA command.
This basically means that the driver can get frames with
a valid BAID that it doesn't know yet.
When that happens, the driver used to WARN.
Fix this by simply not WARN in this case. When the driver
will know abou the BAID, it will initialise the relevant
states and the next frame with a valid BAID will refresh
them.
Fixes: b915c10174fb ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In AP mode, if a station is removed just as it is adding a new stream,
the queue in question will remain stopped and no more TX will happen
in this queue, leading to connection failures and other problems.
This is because under DQA, when tx is deferred because a queue needs
to be allocated, the mac queue for that TID is stopped until the new
stream is added. If at this point the station that this stream
belongs to is removed, all the deferred tx frames are purged, but the
mac queue is not restarted. As a result, all following tx on this
queue will not be transmitted.
Fix this by starting the relevant mac queues when the deferred tx
frames are purged.
Fixes: 24afba7690e4 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
qmi_wwan_disconnect is called twice when disconnecting devices with
separate control and data interfaces. The first invocation will set
the interface data to NULL for both interfaces to flag that the
disconnect has been handled. But the matching NULL check was left
out when qmi_wwan_disconnect was added, resulting in this oops:
usb 2-1.4: USB disconnect, device number 4
qmi_wwan 2-1.4:1.6 wwp0s29u1u4i6: unregister 'qmi_wwan' usb-0000:00:1d.0-1.4, WWAN/QMI device
BUG: unable to handle kernel NULL pointer dereference at 00000000000000e0
IP: qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
PGD 0
P4D 0
Oops: 0000 [#1] SMP
Modules linked in: <stripped irrelevant module list>
CPU: 2 PID: 33 Comm: kworker/2:1 Tainted: G E 4.12.3-nr44-normandy-r1500619820+ #1
Hardware name: LENOVO 4291LR7/4291LR7, BIOS CBET4000 4.6-810-g50522254fb 07/21/2017
Workqueue: usb_hub_wq hub_event [usbcore]
task: ffff8c882b716040 task.stack: ffffb8e800d84000
RIP: 0010:qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
RSP: 0018:ffffb8e800d87b38 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffff8c8824f3f1d0 RDI: ffff8c8824ef6400
RBP: ffff8c8824ef6400 R08: 0000000000000000 R09: 0000000000000000
R10: ffffb8e800d87780 R11: 0000000000000011 R12: ffffffffc07ea0e8
R13: ffff8c8824e2e000 R14: ffff8c8824e2e098 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8c8835300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000e0 CR3: 0000000229ca5000 CR4: 00000000000406e0
Call Trace:
? usb_unbind_interface+0x71/0x270 [usbcore]
? device_release_driver_internal+0x154/0x210
? qmi_wwan_unbind+0x6d/0xc0 [qmi_wwan]
? usbnet_disconnect+0x6c/0xf0 [usbnet]
? qmi_wwan_disconnect+0x87/0xc0 [qmi_wwan]
? usb_unbind_interface+0x71/0x270 [usbcore]
? device_release_driver_internal+0x154/0x210
Reported-and-tested-by: Nathaniel Roach <nroach44@gmail.com>
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e5dadc65f9e0 ("ppp: Fix false xmit recursion detect with two ppp
devices") dropped the xmit_recursion counter incrementation in
ppp_channel_push() and relied on ppp_xmit_process() for this task.
But __ppp_channel_push() can also send packets directly (using the
.start_xmit() channel callback), in which case the xmit_recursion
counter isn't incremented anymore. If such packets get routed back to
the parent ppp unit, ppp_xmit_process() won't notice the recursion and
will call ppp_channel_push() on the same channel, effectively creating
the deadlock situation that the xmit_recursion mechanism was supposed
to prevent.
This patch re-introduces the xmit_recursion counter incrementation in
ppp_channel_push(). Since the xmit_recursion variable is now part of
the parent ppp unit, incrementation is skipped if the channel doesn't
have any. This is fine because only packets routed through the parent
unit may enter the channel recursively.
Finally, we have to ensure that pch->ppp is not going to be modified
while executing ppp_channel_push(). Instead of taking this lock only
while calling ppp_xmit_process(), we now have to hold it for the full
ppp_channel_push() execution. This respects the ppp locks ordering
which requires locking ->upl before ->downl.
Fixes: e5dadc65f9e0 ("ppp: Fix false xmit recursion detect with two ppp devices")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.
V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: f8c6455bb04b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We allocate 'p_info->mfw_mb_cur' and 'p_info->mfw_mb_shadow' but we check
'p_info->mfw_mb_addr' instead of 'p_info->mfw_mb_cur'.
'p_info->mfw_mb_addr' is never 0, because it is initiliazed a few lines
above in 'qed_load_mcp_offsets()'.
Update the test and check the result of the 2 'kzalloc()' instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When Ethernet frames span mulitple URBs, the netdev buffer memory
pointed to by the asix_rx_fixup_info structure remains allocated
during the time gap between the 2 executions of asix_rx_fixup_internal().
This means that if ax88772_unbind() is called within this time
gap to free the memory of the parent private data structure then
a memory leak of the part filled netdev buffer memory will occur.
Therefore, create a new function asix_rx_fixup_common_free() to
free the memory of the netdev buffer and add a call to
asix_rx_fixup_common_free() from inside ax88772_unbind().
Consequently when an unbind occurs part way through receiving
an Ethernet frame, the netdev buffer memory that is holding part
of the received Ethernet frame will now be freed.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a risk that the members of the structure asix_rx_fixup_info
become unsynchronised leading to the possibility of a malfunction.
For example, rx->split_head was not being set to false after an
error was detected so potentially could cause a malformed 32-bit
Data header word to be formed.
Therefore add function reset_asix_rx_fixup_info() to reset all the
members of asix_rx_fixup_info so that future processing will start
with known initial conditions.
Also, if (skb->len != offset) becomes true then call
reset_asix_rx_fixup_info() so that the processing of the next URB
starts with known initial conditions. Without the call, the check
does nothing which potentially could lead to a malfunction
when the next URB is processed.
In addition, for robustness, call reset_asix_rx_fixup_info() before
every error path's "return 0". This ensures that the next URB is
processed from known initial conditions.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In asix_rx_fixup_internal() there is a risk that rx->ax_skb gets
reused after passing the Ethernet frame into the network stack via
usbnet_skb_return().
The risks include:
a) asynchronously freeing rx->ax_skb after passing the netdev buffer
to the NAPI layer which might corrupt the backlog queue.
b) erroneously reusing rx->ax_skb such as calling skb_put_data() multiple
times which causes writing off the end of the netdev buffer.
Therefore add a defensive rx->ax_skb = NULL after usbnet_skb_return()
so that it is not possible to free rx->ax_skb or to apply
skb_put_data() too many times.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing sub channel code did not wait for all the sub-channels
to completely initialize. This could lead to race causing crash
in napi_netif_del() from bad list. The existing code would send
an init message, then wait only for the initial response that
the init message was received. It thought it was waiting for
sub channels but really the init response did the wakeup.
The new code keeps track of the number of open channels and
waits until that many are open.
Other issues here were:
* host might return less sub-channels than was requested.
* the new init status is not valid until after init was completed.
Fixes: b3e6b82a0099 ("hv_netvsc: Wait for sub-channels to be processed during probe")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'iwl_mvm_sar_get_wgds_table()'
We should free 'wgds.pointer' here as done a few lines above in another
error handling path.
It was allocated within 'acpi_evaluate_object()'.
Fixes: c52030a01ccc ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Even the driver doesn't do anything with the clk source for SGMII
ports it needs to be enabled by doing a devm_clk_get(), if there is
a clk source in DT.
Fixes: 0db01097cabd ('xgene: Don't fail probe, if there is no clk resource for SGMII interfaces')
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Tested-by: Laura Abbott <labbott@redhat.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each multicast group (MID) stores a bitmap of ports to which a packet
should be forwarded to in case an MDB entry associated with the MID is
hit.
Since the initial introduction of IGMP snooping in commit 3a49b4fde2a1
("mlxsw: Adding layer 2 multicast support") the driver didn't correctly
free these multicast groups upon ungraceful situations such as the
removal of the upper bridge device or module removal.
The correct way to fix this is to associate each MID with the bridge
ports member in it and then drop the reference in case the bridge port
is destroyed, but this will result in a lot more code and will be fixed
in net-next.
For now, upon module removal, traverse the MID list and release each
one.
Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some operations in the bridge driver such as MDB deletion are preformed
in an atomic context and thus deferred to a process context by the
switchdev infrastructure.
Therefore, by the time the operation is performed by the underlying
device driver it's possible the bridge port context is already gone.
This is especially true for removal flows, but theoretically can also be
invoked during addition.
Remove the warnings in such situations and return normally.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Fixes: 3922285d96e7 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCRQ resources are freed during renegotiation, but they are not
re-allocated afterwards due to some changes in the initialization
process. Fix that by re-allocating the memory after renegotation.
SCRQ's can also be freed if a server capabilities request fails.
If this were encountered during a device reset for example,
SCRQ's may not be re-allocated. This operation is not necessary
anymore so remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
QUERY_DEV_CAP_DIAG_RPRT_PER_PORT
However, it failed to introduce a corresponding entry in function
dump_dev_cap_flags2() for outputting a line in the message log
when this capability bit is set.
The change here fixes that omission.
Fixes: c7c122ed67e4 ("net/mlx4: Add diagnostic counters capability bit")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP
However the value of MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP needs to stay
consistent with the value used in another namespace in
function dump_dev_cap_flags2(), which is manually kept in sync.
The change here restores that consistency.
Fixes: 7c3d21c8153c ("net/mlx4_core: Preparation for VF vlan protocol 802.1ad")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The index value in function dump_dev_cap_flags2() for outputting
"sl to vl mapping table change event support" needs to be
consistent with the value of the enumerated constant
MLX4_DEV_CAP_FLAG2_SL_TO_VL_CHANGE_EVENT defined in file
include/linux/mlx4_device.h
The change here restores that consistency.
Fixes: fd10ed8e6f42 ("IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when WoL is supported but disabled, ethtool reports:
"Supports Wake-on: d".
Fix the indication of Wol support, so that the indication
remains "g" all the time if the NIC supports WoL.
Tested:
As accepted, when NIC supports WoL- ethtool reports:
Supports Wake-on: g
Wake-on: d
when NIC doesn't support WoL- ethtool reports:
Supports Wake-on: d
Wake-on: d
Fixes: 14c07b1358ed ("mlx4: Wake on LAN support")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to handle hard_header_len update
When ifconfig up/down sequence is initiated hard_header_len
get updated incrementally for each ifconfig up /down sequence,
this leads invalid hard_header_len, moving to lan78xx_bind
to have one time update of hard_header_len addresses the issue.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
USB fast connect/disconnect crash fix
When USB plugged/unplugged at fast rate,
lan78xx_mdio_init() in lan78xx_bind() failing case is not handled.
Whenever lan78xx_mdio_init() failed, dev->mdiobus will be freed, however
since lan78xx_bind() not consider as error and try to proceed for
further initialization in lan78xx_probe() which leads system hung/crash.
Also when register_netdev() failed, netdev is freed without calling lan78xx_unbind().
Hence halting the failed cases right manner fixes the system crash/hung issue.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that by using the proper helper function: netdev_alloc_pcpu_stats().
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that. In commit 6c80f3fc2398 ("netvsc: report per-channel stats in
ethtool statistics") netdev_alloc_pcpu_stats() was removed in favor of
open-coding the 64-bits statistics, except that u64_stats_init() was
missed.
Fixes: 6c80f3fc2398 ("netvsc: report per-channel stats in ethtool statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that by using netdev_alloc_pcpu_stats() instead of an open coded
allocation.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 4c3523623dc0 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 4197aa7bb818 ("ixgbevf: provide 64 bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
