| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Query UTC sec and nsec PCI offsets during the pci_init(), to be able to
read UTC time later.
Implement functions to read UTC seconds and nanoseconds from the offset
which was read as part of initialization.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lay the groundwork for Spectrum-2 support. On Spectrum-2, the packets get
the time stamps from the CQE, which means that the time stamp is attached
to its packet.
Configure MTPTPT to set which message types should arrive under which
PTP trap. PTP0 will be used for event message types, which means that
the packets require time stamp. PTP1 will be used for other packets.
Note that in Spectrum-2, all packets contain time stamp by default. The two
types of traps (PTP0, PTP1) will be used to separate between PTP_EVENT
traps and PTP_GENERAL traps, so then the driver will fill the time stamp as
part of the SKB only for event message types.
Later the driver will enable the traps using 'MTPCPC.ptp_trap_en' bit.
Then, PTP packets start arriving through the PTP traps.
Currently, the structure 'mlxsw_sp2_ptp_state' contains only the common
structure, the next patches will extend it.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, Tx completions are reported using Completion Queue Element
version 1 (CQEv1). These elements do not contain the Tx time stamp,
which is fine as Spectrum-1 reads Tx time stamps via a dedicated FIFO
and Spectrum-2 does not currently support PTP.
In preparation for Spectrum-2 PTP support, use CQEv2 for Spectrum-2 and
newer ASICs, as this CQE format encodes the Tx time stamp.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MTPTPT register is used to set which message types should arrive under
which PTP trap. Currently, PTP0 is used for event message types, which
means that the packets require time stamp. PTP1 is used for other packets.
This configuration will be same for Spectrum-2 and newer ASICs. In
preparation for Spectrum-2 PTP support, add helper functions to
configure PTP traps and use them for Spectrum-1. These functions will be
used later also for Spectrum-2.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same function to read the switch id is used by drivers based on
qca8k family switch. Move them to common code to make them accessible
also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same port LAG functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same port VLAN functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Also drop exposing busy_wait and make it static.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same port mirror functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same port FDB/MDB function are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
Also drop bulk read/write functions and make them static
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same set age, MTU and port enable/disable function are used by
driver based on qca8k family switch.
Move them to common code to make them accessible also by other drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same bridge functions are used by drivers based on qca8k family
switch. Move them to common code to make them accessible also by other
drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same logic to disable/enable port, set eee and get ethtool stats is
used by drivers based on qca8k family switch.
Move it to common code to make it accessible also by other drivers.
While at it also drop unnecessary qca8k_priv cast for void pointers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same mib function is used by drivers based on qca8k family switch.
Move it to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same ATU function are used by drivers based on qca8k family switch.
Move the bulk read/write helper to common code to declare these shared
ATU functions in common code.
These helper will be dropped when regmap correctly support bulk
read/write.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same reg table and read/write/rmw function are used by drivers
based on qca8k family switch.
Move them to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The same MIB struct is used by drivers based on qca8k family switch. Move
it to common code to make it accessible also by other drivers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some switch may not support mib autocast feature and require the legacy
way of reading the regs directly.
Make the mib autocast feature optional and permit to declare support for
it using match_data struct in a dedicated qca8k_info_ops struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using of_device_get_match_data is expensive. Cache match data to speed
up access and rework user of match data to use the new cached value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct spelling on 'non-existent' in comment
Signed-off-by: Ruffalo Lavoisier <RuffaloLavoisier@gmail.com>
Link: https://lore.kernel.org/r/20220728032854.151180-1-RuffaloLavoisier@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix following includecheck warning:
./drivers/net/ethernet/mellanox/mlxsw/core_linecard_dev.c: linux/err.h is included more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220727233801.23781-1-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Let the core take the devlink instance lock around health callbacks and
remove the now redundant locking in the drivers.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change devlink instance locks in mlx5 driver to have devlink health
recovery callback locked, while keeping all driver paths which lead to
devl_ API functions called by the driver locked.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change devlink instance locks in mlx4 driver to have devlink reload
callback locked, while keeping all driver paths which leads to devl_ API
functions called by the mlx4 driver locked.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use devl_ API to call devl_port_register() and devl_port_unregister()
instead of devlink_port_register() and devlink_port_unregister(). Add
devlink instance lock in mlx4 driver paths to these functions.
This will be used by the downstream patch to invoke mlx4 devlink reload
callbacks with devlink lock held.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use devl_ API to call devl_region_create() and devl_region_destroy()
instead of devlink_region_create() and devlink_region_destroy().
Add devlink instance lock in mlx4 driver paths to these functions.
This will be used by the downstream patch to invoke mlx4 devlink reload
callbacks with devlink lock held.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change devlink instance locks in mlx5 driver to have devlink reload
callbacks locked, while keeping all driver paths which lead to devl_ API
functions called by the driver locked.
Add mlx5_load_one_devl_locked() and mlx5_unload_one_devl_locked() which
are used by the paths which are already locked such as devlink reload
callbacks.
This patch makes the driver use devl_ API also for traps register as
these functions are called from the driver paths parallel to reload that
requires locking now.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor fw reset code to have the unload driver part done on
mlx5_fw_reset_complete_reload(), so if it was called by the PF which
initiated the reload fw activate flow, the unload part will be handled
by the mlx5_devlink_reload_fw_activate() callback itself and not by the
reset event work.
This will be used by the downstream patch to invoke devlink reload
callbacks with devlink lock held.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add callbacks
=============
.selftest_check: returns true for flash selftest.
.selftest_run: runs a flash selftest.
Also, refactor NVM APIs so that they can be
used with devlink and ethtool both.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Let the TLS TX recycle pool be more flexible in size, by continuously
and dynamically allocating and releasing HW resources in response to
changes in the connections rate and load.
Allocate and release pool entries in bulks (16). Use a workqueue to
release/allocate in the background. Allocate a new bulk when the pool
size goes lower than the low threshold (1K). Symmetric operation is done
when the pool size gets greater than the upper threshold (4K).
Every idle pool entry holds: 1 TIS, 1 DEK (HW resources), in addition to
~100 bytes in host memory.
Start with an empty pool to minimize memory and HW resources waste for
non-TLS users that have the device-offload TLS enabled.
Upon a new request, in case the pool is empty, do not wait for a whole bulk
allocation to complete. Instead, trigger an instant allocation of a single
resource to reduce latency.
Performance tests:
Before: 11,684 CPS
After: 16,556 CPS
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The transport interface send (TIS) object is responsible for performing
all transport related operations of the transmit side. The ConnectX HW
uses a TIS object to save and access the TLS crypto information and state
of an offloaded TX kTLS connection.
Before this patch, we used to create a new TIS per connection and destroy
it once it’s closed. Every create and destroy of a TIS is a FW command.
Same applies for the private TLS context, where we used to dynamically
allocate and free it per connection.
Resources recycling reduce the impact of the allocation/free operations
and helps speeding up the connection rate.
In this feature we maintain a pool of TX objects and use it to recycle
the resources instead of re-creating them per connection.
A cached TIS popped from the pool is updated to serve the new connection
via the fast-path HW interface, updating the tls static and progress
params. This is a very fast operation, significantly faster than FW
commands.
On recycling, a WQE fence is required after the context params change.
This guarantees that the data is sent after the context has been
successfully updated in hardware, and that the context modification
doesn't interfere with existing traffic.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Let the caller of mlx5e_ktls_tx_handle_ooo() take care of updating the
stats, according to the returned value. As the switch/case blocks are
already there, this change saves unnecessary branches in the handler.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TLS TIS objects have a defined role in mapping and reaching the HW TLS
contexts. Some standard TIS attributes (like LAG port affinity) are
not relevant for them.
Use a dedicated TLS TIS create function instead of the generic
mlx5e_create_tis.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
delete extra space and tab in blank line, there is no functional change.
Signed-off-by: Xie Shaowen <studentxswpy@163.com>
Link: https://lore.kernel.org/r/20220727081253.3043941-1-studentxswpy@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If mediatek_dwmac_clks_config() fails, then call stmmac_remove_config_dt()
before returning. Otherwise it is a resource leak.
Fixes: fa4b3ca60e80 ("stmmac: dwmac-mediatek: fix clock issue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YuJ4aZyMUlG6yGGa@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use correct vendor for Xilinx versions of Cadence MACB/GEM Ethernet
controller. The Versal compatible was not released, so it can be
changed. Zynq-7xxx and Ultrascale+ has to be kept in new and deprecated
form.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Harini Katakam <harini.katakam@amd.com>
Link: https://lore.kernel.org/r/20220726070802.26579-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The current implementation of fun_xdp_tx(), used for XPD_TX, is
incorrect in that it takes an address/length pair and later releases it
with page_frag_free(). It is OK for XDP_TX but the same code is used by
ndo_xdp_xmit. In that case it loses the XDP memory type and releases the
packet incorrectly for some of the types. Assorted breakage follows.
Change fun_xdp_tx() to take xdp_frame and rely on xdp_return_frame() in
reclaim.
Fixes: db37bc177dae ("net/funeth: add the data path")
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20220726215923.7887-1-dmichail@fungible.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ice: PPPoE offload support
Marcin Szycik says:
Add support for dissecting PPPoE and PPP-specific fields in flow dissector:
PPPoE session id and PPP protocol type. Add support for those fields in
tc-flower and support offloading PPPoE. Finally, add support for hardware
offload of PPPoE packets in switchdev mode in ice driver.
Example filter:
tc filter add dev $PF1 ingress protocol ppp_ses prio 1 flower pppoe_sid \
1234 ppp_proto ip skip_sw action mirred egress redirect dev $VF1_PR
Changes in iproute2 are required to use the new fields (will be submitted
soon).
ICE COMMS DDP package is required to create a filter in ice.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Add support for PPPoE hardware offload
flow_offload: Introduce flow_match_pppoe
net/sched: flower: Add PPPoE filter
flow_dissector: Add PPPoE dissectors
====================
Link: https://lore.kernel.org/r/20220726203133.2171332-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit 35d099da41967f114c6472b838e12014706c26e7, reversing
changes made to 58d8bcd47ecc55f1ab92320fe36c31ff4d83cc0c.
I wrongly applied that to the net-next tree instead of the intended
target tree (net). Reverting it on net-next.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 3c783b83bd0f ("net: dsa: mv88e6xxx: get rid of SPEED_MAX setting")
stopped relying on SPEED_MAX constant and hardcoded speed settings
for the switch ports and rely on phylink configuration.
It turned out, however, that when the relevant code is called,
the mac_capabilites of CPU/DSA port remain unset.
mv88e6xxx_setup_port() is called via mv88e6xxx_setup() in
dsa_tree_setup_switches(), which precedes setting the caps in
phylink_get_caps down in the chain of dsa_tree_setup_ports().
As a result the mac_capabilites are 0 and the default speed for CPU/DSA
port is 10M at the start. To fix that, execute mv88e6xxx_get_caps()
and obtain the capabilities driectly.
Fixes: 3c783b83bd0f ("net: dsa: mv88e6xxx: get rid of SPEED_MAX setting")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220726230918.2772378-1-mw@semihalf.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-07-26
This series contains updates to ice driver only.
Przemyslaw corrects accounting for VF VLANs to allow for correct number
of VLANs for untrusted VF. He also correct issue with checksum offload
on VXLAN tunnels.
Ani allows for two VSIs to share the same MAC address.
Maciej corrects checked bits for descriptor completion of loopback
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: do not setup vlan for loopback VSI
ice: check (DD | EOF) bits on Rx descriptor rather than (EOP | RS)
ice: Fix VSIs unable to share unicast MAC
ice: Fix tunnel checksum offload with fragmented traffic
ice: Fix max VLANs available for VF
====================
Link: https://lore.kernel.org/r/20220726204646.2171589-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sending a PTP packet can imply to use the normal TX driver datapath but
invoked from the driver's ptp worker. The kernel generic TX code
disables softirqs and preemption before calling specific driver TX code,
but the ptp worker does not. Although current ptp driver functionality
does not require it, there are several reasons for doing so:
1) The invoked code is always executed with softirqs disabled for non
PTP packets.
2) Better if a ptp packet transmission is not interrupted by softirq
handling which could lead to high latencies.
3) netdev_xmit_more used by the TX code requires preemption to be
disabled.
Indeed a solution for dealing with kernel preemption state based on static
kernel configuration is not possible since the introduction of dynamic
preemption level configuration at boot time using the static calls
functionality.
Fixes: f79c957a0b537 ("drivers: net: sfc: use netdev_xmit_more helper")
Signed-off-by: Alejandro Lucero <alejandro.lucero-palau@amd.com>
Link: https://lore.kernel.org/r/20220726064504.49613-1-alejandro.lucero-palau@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We try using cancel_delayed_work_sync() to prevent the work from
enabling NAPI. This is insufficient since we don't disable the source
of the refill work scheduling. This means an NAPI poll callback after
cancel_delayed_work_sync() can schedule the refill work then can
re-enable the NAPI that leads to use-after-free [1].
Since the work can enable NAPI, we can't simply disable NAPI before
calling cancel_delayed_work_sync(). So fix this by introducing a
dedicated boolean to control whether or not the work could be
scheduled from NAPI.
[1]
==================================================================
BUG: KASAN: use-after-free in refill_work+0x43/0xd4
Read of size 2 at addr ffff88810562c92e by task kworker/2:1/42
CPU: 2 PID: 42 Comm: kworker/2:1 Not tainted 5.19.0-rc1+ #480
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: events refill_work
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_report.cold+0xbb/0x6ac
? _printk+0xad/0xde
? refill_work+0x43/0xd4
kasan_report+0xa8/0x130
? refill_work+0x43/0xd4
refill_work+0x43/0xd4
process_one_work+0x43d/0x780
worker_thread+0x2a0/0x6f0
? process_one_work+0x780/0x780
kthread+0x167/0x1a0
? kthread_exit+0x50/0x50
ret_from_fork+0x22/0x30
</TASK>
...
Fixes: b2baed69e605c ("virtio_net: set/cancel work on ndo_open/ndo_stop")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the ksz8795 cpu configuration to use the ksz common
xmii set functions.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
