| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Before commit 99724c18fc66 ("mlxsw: spectrum: Introduce support for
router interfaces") we used to assign vFIDs to the created vPorts. Since
these vPorts were used for slow path traffic we had to disable learning
for them, as it doesn't make sense to have it enabled.
This is no longer the case and now vPorts are either used for router
interfaces (for which learning is disabled by the firmware) or bridge
ports (for which learning is explicitly enabled by the driver).
Therefore, we can remove the learning configuration upon vPort creation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We now offload the learning configuration to the device and don't rely
on the driver to decide whether to learn the FDB record, so remove the
check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now we simply stored the learning configuration of a bridge
port in the driver and decided whether to learn a new FDB record based
on this value.
However, this is sub-optimal in cases where learning is disabled on the
bridge port, as the device repeatedly generates learning notifications
for the same record.
Instead, offload the learning configuration to the device, thereby
preventing it from generating notifications when learning is disabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are going to prevent the device from generating learning
notifications for a port that was configured with learning disabled.
Since learning configuration is done per {Port, VID} we need to apply
the port's learning configuration for any VID that is added to the
bridge port's VLAN filter list.
When a VID is added to the VLAN filter list of a VLAN-aware bridge port,
configure the {Port, VID} learning status according to the port's
configuration. When the VID is removed, disable learning for the {Port,
VID}.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing VLANs from the VLAN-aware bridge we shouldn't abort on the
first error, as we'll otherwise have resources that will never be freed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 05978481e77e ("mlxsw: spectrum: Create PVID vPort before
registering netdevice") removed __mlxsw_sp_port_vlans_del() from the
init sequence of the driver, which forced it to be non-symmetric with
regards to __mlxsw_sp_port_vlans_add().
Make both functions symmetric as the constraint no longer exists.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now a learning session ended whenever the number of queried
records was zero. This turned out to be problematic in situations where
a large number of MACs (48K) had to be processed by the switch driver,
as RTNL mutex is held during the learning session.
Instead, limit the number of FDB records that can be processed in a
session to 64. This means that every time the device is queried for
learning notifications (currently, every 100ms), up to 64 records will
be processed by the switch driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the function mlxsw_router_neigh_construct search the rif according
to the neighbour dev other than the dev that was passed to the ndo, thus
allowing creating neigbhours upon stacked devices.
Fixes: 6cf3c971dc84 ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we have a layer 3 interface on top of a bridge (VLAN / FID RIF),
then we should flood the following packet types to the router:
* Broadcast: If DIP is the broadcast address of the interface, then we
need to be able to get it to CPU by trapping it following route lookup.
* Reserved IP multicast (224.0.0.X): Some control packets (e.g. OSPF)
use this range and are trapped in the router block.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma
Saeed Mahameed says:
====================
Mellanox mlx5 core driver updates 2016-08-24
This series contains some low level and API updates for mlx5 core
driver interface and mlx5_ifc.h, plus mlx5 LAG core driver support,
to be shared as base code for net-next and rdma mlx5 4.9 submissions.
From Alex and Artemy, Update mlx5_ifc for modify RQ and XRC bits.
From Noa, Expose mlx5 link modes so they can be used in RDMA tree for rdma tools.
From Aviv, LAG support needed for RDMA.
- Add needed hardware structures, layouts and interface
- mlx5 core driver LAG implementation
- Introduce mlx5 core driver LAG API for mlx5_ib
From Maor, add two low level patches for mlx5 hardware sniffer QP
infrastructure bits and capabilities, plus added the namespace for sniffer
steering tables. Needed for RDMA subtree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using sock_tx_timestamp, use skb_tx_timestamp to record
software transmit timestamp of a packet.
sock_tx_timestamp resets and overrides the tx_flags of the skb.
The function is intended to be called from within the protocol
layer when creating the skb, not from a device driver. This is
inconsistent with other drivers and will cause issues for TCP.
In TCP, we intend to sample the timestamps for the last byte
for each sendmsg/sendpage. For that reason, tcp_sendmsg calls
tcp_tx_timestamp only with the last skb that it generates.
For example, if a 128KB message is split into two 64KB packets
we want to sample the SND timestamp of the last packet. The current
code in the tun driver, however, will result in sampling the SND
timestamp for both packets.
Also, when the last packet is split into smaller packets for
retranmission (see tcp_fragment), the tun driver will record
timestamps for all of the retransmitted packets and not only the
last packet.
Fixes: eda297729171 (tun: Support software transmit time stamping.)
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Francis Yan <francisyyan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the return type of ena_set_push_mode() to be void,
as it always returns 0.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/phy/xilinx_gmii2rgmii.c:61:5: warning:
symbol 'xgmiitorgmii_probe' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add provision for configuring the fastpath queues with Tx (or Rx) only
functionality.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently enable interrupts before we enable NAPI. If an RX interrupt
hits before we enabled NAPI then the NAPI callback is never called and
we leave the hardware with RX interrupts disabled, which of course leads
us to never handling received packets. Fix this by moving the interrupt
enable to after we've enable NAPI and the reclaim tasklet.
Fixes: cd5e41234729 ("dwc_eth_qos: do phy_start before resetting hardware")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clk_prepare_enable() may fail, so we should better check its return
value and propagate it in the case of failure
While at it, replace __lpc_eth_clock_enable() with a plain
clk_prepare_enable/clk_disable_unprepare() call in order to
simplify the code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we disable SRIOV, we used to unregister the netdev but wasn't
freed. But next time when the same netdev is registered, since the state
was in 'NETREG_UNREGISTERED', we used to hit BUG_ON in register_netdevice,
where it expects the state to be 'NETREG_UNINITIALIZED'.
Alloc netdev and register them while configuring SRIOV, and free them
when SRIOV is disabled. Also added a new function to setup ethernet
properties instead of using ether_setup. Set carrier off by default,
since we don't have to do any transmit on the interface.
Fixes: 7829451c695e ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PORT_RATE_CONTROL register works differently on 88e6095/6095f/6131
in comparison to 6123/61/65, and 0x0 disables. The distinction was lost
Linux 4.1 --> 4.2
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like the ksz8081, the ksz9031 has the behavior where it will clear the
interrupt enable bits when leaving power down. This takes advantage of the
solution provided by f5aba91.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
liquidio_set_rxcsum_command is a local function only, no need to expose
it outside of lio_main.c so declare it static and make sparse happy.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current scatter-gather logic in gianfar is flawed, since
it does not consider the eTSEC's RxBD 'Data Length' field is
context depening: for the last fragment it contains the full
frame size, while fragments contain the fragment size, which
equals the value written to register MRBLR.
This causes data corruption as soon as the hardware starts
to fragment receiving frames. As a result, the size of
fragmented frames is increased by
(nr_frags - 1) * MRBLR
We first noticed this issue working with DSA, where an ICMP
request sized 1472 bytes causes the scatter-gather logic to
kick in. The full Ethernet frame (1518) gets increased by
DSA (4), GMAC_FCB_LEN (8), and FSL_GIANFAR_DEV_HAS_TIMER
(priv->padding=8) to a total of 1538 octets, which is
fragmented by the hardware and reconstructed by the driver
to a 3074 octet frame.
This patch fixes the problem by adjusting the size of
the last fragment.
It was tested by setting MRBLR to different multiples of
64, proving correct scatter-gather operation on frames
with up to 9000 octets in size.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The eTSEC register MRBLR defines the maximum space in
the RX buffers and is set to 1536 by gianfar. This
reasonably covers the common use case where the MTU
is kept at default 1500. In that case, the largest
Ethernet frame size of 1518 plus an optional
GMAC_FCB_LEN of 8, and an additional padding of 8
to handle FSL_GIANFAR_DEV_HAS_TIMER totals to 1534
and nicely fit within the chosen MRBLR.
Alas, if the eTSEC is attached to a DSA enabled switch,
the (E)DSA header extension (4 or 8 bytes) causes every
maximum sized frame to be fragmented by the hardware.
This patch increases the maximum RX buffer size by 8
and rounds up to the next multiple of 64, which the
hardware's defines as RX buffer granularity.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Printing console messages is not helpful when system is out of memory;
and can be disastrous with netconsole. Instead keep statistics
of these anomalous conditions.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make netvsc on vmbus behave more like PCI.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable m_ret is only used in one basic block.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No caller checks the return value.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Break the different cases, code is cleaner if broken up
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rearrange the transmit routine to eliminate goto's and unnecessary
boolean variables. Use standard functions to test for vlan tag.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move initialization to allocate where other fields are initialized.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Always returns 0 and no callers check.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't hard code size of array of NDIS versions.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several new functions were introduced into hyperv.h but only used in one file.
Move them and let compiler decide on inline.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix most of the complaints about the style of the code.
Things like extra blank lines and return statements.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Better to use kcalloc rather than kzalloc and multiply for an array.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function get_netvsc_net_device had conditional locking. This was
unnecessary, incorrect, but harmless. It was unnecessary since the
code is only called from netlink netdev event callback where RTNL
is always acquired before the callbacks are run. It was incorrect
because of use of trylock and then continuing.
Fix by replacing with proper assertion.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma
Saeed Mahameed says:
====================
Mellanox mlx5 core driver updates 2016-08-20
This series contains several low level and API updates for mlx5 core
commands interface and mlx5_ifc.h to be shared as base code for net-next and
rdma mlx5 4.9 submissions.
From Saeed, ten patches that refactors old layouts of firmware commands which
were manually generated before we introduced the mlx5_ifc, now all of the firmware
commands inbox/outbox layouts moved to use mlx5_ifc and we remove the old
manually generated structures. Plus to those ten patches, we add two patches
that unifies mlx5 commands execution interface and improve the driver log messages
in that area.
From Hadar and Ilya, added the needed hardware bits and infrastructure for
minimum inline headers setting and encap/decap commands and capabilities,
needed for E-Switch offloads.
This series applies on top latest net-next and rdma/master, and smoothly merges with
the latest "Mellanox 100G mlx5 fixes 2016-08-16" series already applied into net branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These ops allow to control number of channels driver is allowed to
work with at cpdma level. The maximum number of channels is 8 for
rx and 8 for tx. In dual_emac mode the h/w channels are shared
between two interfaces and changing number on one interface changes
number of channels on another.
How many channels are supported and enabled:
$ ethtool -l ethX
Change number of channels (up to 8)
$ ethtool -L ethX rx 6 tx 6
Per-channel statistic:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
internals
Keep the driver internals in C file. Currently it's not required for
drivers to know rx or tx a channel is, except create function.
So correct "channel create" function, and use all channel struct
macroses only for internal use.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw h/w supports up to 8 tx and 8 rx channels. This patch adds
multi-queue support to the driver only, shaper configuration will
be added with separate patch series. Default shaper mode, as
before, priority mode, but with corrected priority order, 0 - is
highest priority, 7 - lowest.
The poll function handles all unprocessed channels, till all of
them are free, beginning from hi priority channel.
In dual_emac mode the channels are shared between two network devices,
as it's with single-queue default mode.
The statistic for every channel can be read with:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupts shouldn't be disabled while receiving skb, but while
ctrl_stop, the channels are stopped and all remaining packets are
handled with netif_receive_skb(), it can cause WARN_ONCE when ctrl
is stopping while not all packets were handled with NAPIs:
lock_irq_save
cpdma_ctlr_stop
cpdma_chan_top
__cpdma_chan_free
cpsw_rx_handler
netif_receive_skb
So, split locking while ctrl stop thus interrupts are still
enabled while skbs handling. It can cause WARN_ONCE in rare
cases when ctrl is stopping while not all packets were handled
with NAPIs.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx channels share same pool of descriptors. Thus one channel can
block another if pool is emptied by one. But, the shaper should
decide which channel is allowed to send packets. To avoid such
impact of one channel on another, let every channel to have its
own piece of pool.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without it, a mv88e6131 switch will not forward incoming unicast
packets to the CPU port.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PPU method of accessing PHYs makes use of a timer. Make sure this
timer is deleted before unloading the driver.
Reported-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Older chips only support DSA tagging on the CPU port. New devices
support both DSA and EDSA. The driver needs to tell the core the tag
protocol to use, and configure the switch for what is available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement set_tx_maxrate NDO to perform per queue tx rate limiting.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
