| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On some platforms, the comphy is between the MAC GoP and the PHYs. The
mvpp2 driver currently relies on the firmware/bootloader to configure
the comphy. As a comphy driver was added to the generic PHY framework,
this patch uses it in the mvpp2 driver to configure the comphy at boot
time to avoid relying on the bootloader.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not hold a spinlock while pushing the skb into the networking
stack, so move the call to netif_rx_ni out of the critical region to where
we have dropped the spinlock.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device. This will be used to provide all MAP functionality
on future hardware in a single consistent location.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A stray return was added in the macro bcmgenet_##name##_writel where it
should not, drop it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 69d2ea9c7989 ("net: bcmgenet: Use correct I/O accessors")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GENET driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make these const as they are not modified anywhere.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a difference in the bit position of the normal interrupt summary
enable (NIE) and abnormal interrupt summary enable (AIE) between revisions
of the hardware. For older revisions the NIE and AIE bits are positions
16 and 15 respectively. For newer revisions the NIE and AIE bits are
positions 15 and 14. The effect in changing the bit position is that
newer hardware won't receive AIE interrupts in the current version of the
driver. Specifically, the driver uses this interrupt to collect
statistics on when a receive buffer unavailable event occurs and to
restart the driver/device when a fatal bus error occurs.
Update the driver to set the interrupt enable bit based on the reported
version of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The values are shared between VXLAN-GPE and NSH. Originally probably by
coincidence but I notified both working groups about this last year and they
seem to keep the values in sync since then.
Hopefully they'll get a single IANA registry for the values, too. (I asked
them for that.)
Factor out the code to be shared by the NSH implementation.
NSH and MPLS values are added in this patch, too. For MPLS, the drafts
incorrectly assign only a single value, while we have two MPLS ethertypes.
I raised the problem with both groups. For now, I assume the value is for
unicast.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding support for updating the FW on new port mac, when port mac change
is requested by the user. This info is required by the FW as OEM
management tools require this info directly from the NIC FW.
Check device capability bit to verify the FW supports user mac.
If the FW does support it, use set_port command to notify the FW on the
new mac.
The feature is relevant only to PF port mac.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing the sizeof style usage in the patch cited below,
one brackets misplacement was introduced. Here we fix it.
Fixes: 31975e27a4b5 ("mlx4: sizeof style usage")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "lg" variable is declared as int so in all places where this variable
is used as a shift operand, the output will be int too.
This produces the following smatch warning:
drivers/net/ethernet/mellanox/mlx4/fw.c:1532 mlx4_map_cmd() warn:
should '1 << lg' be a 64 bit type?
Simple declaration of "1" to be "1ULL" will fix the issue.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to avoid temporary large structs on the stack,
allocate them dynamically.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tal Alon <talal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently uses __raw_{read,write}l which works for all
platforms supported: Broadcom MIPS LE/BE (native endian), ARM LE (native
endian) but not ARM BE (registers are still LE). Switch to using the
proper accessors for all platforms and explain why Broadcom MIPS BE is
special here, in doing so, we introduce a couple of helper functions to
abstract these differences.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RSB_SWAP0 needs to match the host CPU endian, and it needs to be set
for LE and clear for BE. RSB_SWAP1 must always be cleared for SYSTEMPORT
Lite.
With these settings, we have the Receive Status Block always match the
host endian and we do not need to perform any conversion. Since there is
not necessarily a CONFIG_CPU_LITTLE_ENDIAN option defined, we test for
!CONFIG_CPU_BIG_ENDIAN which is guaranteed to be set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Starfigther 2 driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SYSTEMPORT driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
rsi driver is getting a lot of new features lately, but as usual
active development happening on iwlwifi as well as other drivers.
I pulled wireless-drivers to fix multiple conflicts in iwlwifi and to
make it easier further development.
Major changes:
ath10k
* initial UBS bus support (no full support yet)
* add tdls support for 10.4 firmware
ath9k
* add Dell Wireless 1802
wil6210
* support FW RSSI reporting
rsi
* support legacy power save, U-APSD, rf-kill and AP mode
* RTS threshold configuration
brcmfmac
* support CYW4373 SDIO/USB chipset
iwlwifi
* some more code moved to a new directory
* add new PCI ID for 7265D
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clk_div_table are not supposed to change at runtime.
meson8b_dwmac structure is working with const clk_div_table.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When bnxt VF-reps are not compiled in (CONFIG_BNXT_SRIOV is off)
bnxt_tc.c needs a dummy definition of the routine bnxt_vf_rep_get_fid().
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 2ae7408fedfe ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We probably don't want to enable code supporting particular hardware by
default e.g. when someone does 'make defconfig'. Other ethernet modules
don't do it.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds code to implement TC_CLSFLOWER_STATS TC-cmd and the
required FW code to query the stats from the HW.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the hwrm_cfa_flow_alloc/free() routines
that are needed to issue the FW cmds needed for TC flower offload.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for offloading TC based flow
rules and actions for the 'flower' classifier in the bnxt_en driver.
It includes logic to parse flow rules and actions received from the
TC subsystem, store them and issue the corresponding
hwrm_cfa_flow_alloc/free FW cmds. L2/IPv4/IPv6 flows and drop,
redir, vlan push/pop actions are supported in this patch.
In this patch the hwrm_cfa_flow_xxx routines are just stubs.
The code for these routines is introduced in the next patch for easier
review. Also, the code to query the TC/flower action stats will
be introduced in a subsequent patch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The routine bnxt_link_bp_to_dl() is used to set the devlink ptr
in bnxt struct (bp) and also to set the bnxt back ptr in
the devlink struct. If devlink_register() fails, bp->dl must
be cleared which is not happening currently. This patch fixes
bnxt_link_bp_to_dl() to clear bp->dl by passing a NULL dl ptr.
Fixes: 4ab0c6a8ffd7 ("bnxt_en: add support to enable VF-representors")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce default rings from 8 to 4 on multi-port cards to reduce memory
usage.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we cannot allocate RX buffers in the NAPI poll loop when processing
an RX event, the current code does not count that event towards the NAPI
budget. This can cause us to potentially loop forever in NAPI if we
consistently cannot allocate new buffers. Improve it by counting
-ENOMEM event as 1 towards the NAPI budget.
Cc: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
initialize board_info values with proper enums for defensive programming
purposes. This will avoid any errors of the enums being declared not
lining up with the board_info array.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add PCIe device ID for bcm58802 and bcm58808. Also add chip number
update to declare bcm588xx as chip class phase 4 and later
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides hints to irqbalance to map bnxt_en device IRQs
to specific CPU cores. cpumask_local_spread() is used, which first
maps IRQs to near NUMA cores; when those cores are exhausted, IRQs
are mapped to far NUMA cores.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the number of TX rings is changed (e.g. ethtool -L, enabling XDP TX
rings, etc), the current code tries to reserve the new number of TX rings
before closing and re-opening the NIC. If we are unable to reserve the
new TX rings, we abort the operation and keep the current TX rings.
The problem is that the firmware will disable the current TX rings even
when it cannot reserve the new set of TX rings. We fix it as follows:
1. Instead of reserving the new set of TX rings, just ask the firmware
to check if the new set of TX rings is available. There is a flag in
the firmware message to do that. If not available, abort and the
current TX rings will not be disabled.
2. Do the actual TX ring reservation in the path that opens the NIC.
We keep the number of TX rings currently successfully reserved. If the
number of TX rings is different than the reserved TX rings, we call
firmware and reserve again.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flow APIs are added in this firmware interface.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register the ndo_vlan_rx_{add,kill}_vid callbacks and set the
NETIF_F_HW_VLAN_CTAG_FILTER if NCSI is available.
This allows the VLAN core to notify the NCSI driver when changes occur
so that the remote NCSI channel can be properly configured to filter on
the set VLAN tags.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-08-27
This series contains updates to i40e and i40evf only.
Sudheer updates code comments and state variable so that adminq_subtask
will have accutate information whenever it gets scheduled.
Mariusz stores information about FEC modes, to be used to printing link
states information, so that we do not need to call admin queue when
reporting link status. Adds VF support for controlling VLAN tag
stripping via ethtool.
Jake provides the majority of changes in this series, starting with
increasing the size of the prefix buffer so that it can hold enough
characters for every possible input, which prevents snprintf truncation.
Fixed other string truncation errors/warnings produced by GCC 7.x.
Removed an unnecessary workaround for resetting XPS. Fixed an issue
where there is a mismatched affinity mask value, so initialize the value
to cpu_possible_mask and invert the logic for checking incorrect CPU vs
IRQ affinity so that the exceptional case is handled at the check.
Removed ULTRA latency mode due to several issues found and will be
looking at better solution for small packet workloads.
Akeem fixes an issue where the incorrect flag was being used to set
promiscuous mode for unicast, which was enabling promiscuous mode only
for multicast instead of unicast.
Carolyn fixes an issue where an error return value is set, but this
value can be overwritten before we actually do exit the function. So
remove the error code assignment and add code comments for better
understanding on why we do not need to set and return the error.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the search for index of constant buffer size
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the hw MTU limitation by setting max_mtu
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the irda drivers from drivers/net/irda/ to
drivers/staging/irda/drivers as they will be deleted in a future kernel
release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the skb hash when then FMan Keygen hash result is available.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow ethtool control of the Rx flow hashing. By default RSS is
enabled, this allows to turn it off by bypassing the FMan Keygen
block and sending all traffic on the default Rx frame queue.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a block of 128 Rx frame queues per port. The FMan hardware will
send traffic on one of these queues based on the FMan port Parse
Classify Distribute setup. The hash computed by the FMan Keygen
block will select the Rx FQ.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the FMan Keygen with a hardcoded scheme to spread
incoming traffic on a FQ range based on source and destination IPs
and ports.
Signed-off-by: Iordache Florinel <florinel.iordache@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kfree on NULL pointer is a no-op and therefore checking is redundant.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During the neighbor traversal the neighbors from different families
should be ignored.
Fixes: c58035a74aba ("mlxsw: spectrum_dpipe: Add support for IPv4 host table dump")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Makes no sense to have dpipe compiled in when devlink is not enabled,
because the devlink dpipe registation is noop function. So don't compile
it in. This also fixes missing extern structs errors.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: a86f030915f2 ("mlxsw: spectrum_dpipe: Add support for IPv4 host table dump")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xen driver initializes struct ubuf_info fields using designated
initializers. I recently moved these fields inside a nested anonymous
struct inside an anonymous union. I had missed this use case.
This breaks compilation of xen-netback with older compilers.
>From kbuild bot with gcc-4.4.7:
drivers/net//xen-netback/interface.c: In function
'xenvif_init_queue':
>> drivers/net//xen-netback/interface.c:554: error: unknown field 'ctx' specified in initializer
>> drivers/net//xen-netback/interface.c:554: warning: missing braces around initializer
drivers/net//xen-netback/interface.c:554: warning: (near initialization for '(anonymous).<anonymous>')
>> drivers/net//xen-netback/interface.c:554: warning: initialization makes integer from pointer without a cast
>> drivers/net//xen-netback/interface.c:555: error: unknown field 'desc' specified in initializer
Add double braces around the designated initializers to match their
nested position in the struct. After this, compilation succeeds again.
Fixes: 4ab6c99d99bb ("sock: MSG_ZEROCOPY notification coalescing")
Reported-by: kbuild bot <lpk@intel.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dynamic ITR algorithm depends on a calculation of usecs which
assumes that the interrupts have been firing constantly at the interrupt
throttle rate. This is not guaranteed because we could have a low packet
rate, or have been polling in software.
We'll estimate whether this is the case by using jiffies to determine if
we've been too long. If the time difference of jiffies is larger we are
guaranteed to have an incorrect calculation. If the time difference of
jiffies is smaller we might have been polling some but the difference
shouldn't affect the calculation too much.
This ensures that we don't get stuck in BULK latency during certain rare
situations where we receive bursts of packets that force us into NAPI
polling.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit c56625d59726 ("i40e/i40evf: change dynamic interrupt
thresholds") a new higher latency ITR setting called I40E_ULTRA_LATENCY
was added with a cryptic comment about how it was meant for adjusting Rx
more aggressively when streaming small packets.
This mode was attempting to calculate packets per second and then kick
in when we have a huge number of small packets.
Unfortunately, the ULTRA setting was kicking in for workloads it wasn't
intended for including single-thread UDP_STREAM workloads.
This wasn't caught for a variety of reasons. First, the ip_defrag
routines were improved somewhat which makes the UDP_STREAM test still
reasonable at 10GbE, even when dropped down to 8k interrupts a second.
Additionally, some other obvious workloads appear to work fine, such
as TCP_STREAM.
The number 40k doesn't make sense for a number of reasons. First, we
absolutely can do more than 40k packets per second. Second, we calculate
the value inline in an integer, which sometimes can overflow resulting
in using incorrect values.
If we fix this overflow it makes it even more likely that we'll enter
ULTRA mode which is the opposite of what we want.
The ULTRA mode was added originally as a way to reduce CPU utilization
during a small packet workload where we weren't keeping up anyways. It
should never have been kicking in during these other workloads.
Given the issues outlined above, let's remove the ULTRA latency mode. If
necessary, a better solution to the CPU utilization issue for small
packet workloads will be added in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit 96db776a3682 ("i40e/vf: fix interrupt affinity bug")
we added some code to force exit of polling in case we did
not have the correct CPU. This is important since it was possible for
the IRQ affinity to be changed while the CPU is pegged at 100%. This can
result in the polling routine being stuck on the wrong CPU until
traffic finally stops.
Unfortunately, the implementation, "if the CPU is correct, exit as
normal, otherwise, fall-through to the end-polling exit" is incredibly
confusing to reason about. In this case, the normal flow looks like the
exception, while the exception actually occurs far away from the if
statement and comment.
We recently discovered and fixed a bug in this code because we were
incorrectly initializing the affinity mask.
Re-write the code so that the exceptional case is handled at the check,
rather than having the logic be spread through the regular exit flow.
This does end up with minor code duplication, but the resulting code is
much easier to reason about.
The new logic is identical, but inverted. If we are running on a CPU not
in our affinity mask, we'll exit polling. However, the code flow is much
easier to understand.
Note that we don't actually have to check for MSI-X, because in the MSI
case we'll only have one q_vector, but its default affinity mask should
be correct as it includes all CPUs when it's initialized. Further, we
could at some point add code to setup the notifier for the non-MSI-X
case and enable this workaround for that case too, if desired, though
there isn't much gain since its unlikely to be the common case.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
