| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.
The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.
This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In yam_ioctl(), the concrete ioctl command is firstly copied from the
user-space buffer 'ifr->ifr_data' to 'ioctl_cmd' and checked through the
following switch statement. If the command is not as expected, an error
code EINVAL is returned. In the following execution the buffer
'ifr->ifr_data' is copied again in the cases of the switch statement to
specific data structures according to what kind of ioctl command is
requested. However, after the second copy, no re-check is enforced on the
newly-copied command. Given that the buffer 'ifr->ifr_data' is in the user
space, a malicious user can race to change the command between the two
copies. This way, the attacker can inject inconsistent data and cause
undefined behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In cxgb_extension_ioctl(), the command of the ioctl is firstly copied from
the user-space buffer 'useraddr' to 'cmd' and checked through the
switch statement. If the command is not as expected, an error code
EOPNOTSUPP is returned. In the following execution, i.e., the cases of the
switch statement, the whole buffer of 'useraddr' is copied again to a
specific data structure, according to what kind of command is requested.
However, after the second copy, there is no re-check on the newly-copied
command. Given that the buffer 'useraddr' is in the user space, a malicious
user can race to change the command between the two copies. By doing so,
the attacker can supply malicious data to the kernel and cause undefined
behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL is returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.
Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().
This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.
Fixes: 9525ae83959b6 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83ebc ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b70567f ("be2net: Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.
If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.
Fixes: 30f529473ec9 ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0ff ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
team's ndo_add_slave() acquires 'team->lock' and later tries to open the
newly enslaved device via dev_open(). This emits a 'NETDEV_UP' event
that causes the VLAN driver to add VLAN 0 on the team device. team's
ndo_vlan_rx_add_vid() will also try to acquire 'team->lock' and
deadlock.
Fix this by checking early at the enslavement function that a team
device is not being enslaved to itself.
A similar check was added to the bond driver in commit 09a89c219baf
("bonding: disallow enslaving a bond to itself").
WARNING: possible recursive locking detected
4.18.0-rc7+ #176 Not tainted
--------------------------------------------
syz-executor4/6391 is trying to acquire lock:
(____ptrval____) (&team->lock){+.+.}, at: team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
but task is already holding lock:
(____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&team->lock);
lock(&team->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by syz-executor4/6391:
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:77 [inline]
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x412/0xc30 net/core/rtnetlink.c:4662
#1: (____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947
stack backtrace:
CPU: 1 PID: 6391 Comm: syz-executor4 Not tainted 4.18.0-rc7+ #176
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_deadlock_bug kernel/locking/lockdep.c:1765 [inline]
check_deadlock kernel/locking/lockdep.c:1809 [inline]
validate_chain kernel/locking/lockdep.c:2405 [inline]
__lock_acquire.cold.64+0x1fb/0x486 kernel/locking/lockdep.c:3435
lock_acquire+0x1e4/0x540 kernel/locking/lockdep.c:3924
__mutex_lock_common kernel/locking/mutex.c:757 [inline]
__mutex_lock+0x176/0x1820 kernel/locking/mutex.c:894
mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:909
team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
vlan_add_rx_filter_info+0x14a/0x1d0 net/8021q/vlan_core.c:210
__vlan_vid_add net/8021q/vlan_core.c:278 [inline]
vlan_vid_add+0x63e/0x9d0 net/8021q/vlan_core.c:308
vlan_device_event.cold.12+0x2a/0x2f net/8021q/vlan.c:381
notifier_call_chain+0x180/0x390 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1735
call_netdevice_notifiers net/core/dev.c:1753 [inline]
dev_open+0x173/0x1b0 net/core/dev.c:1433
team_port_add drivers/net/team/team.c:1219 [inline]
team_add_slave+0xa8b/0x1c30 drivers/net/team/team.c:1948
do_set_master+0x1c9/0x220 net/core/rtnetlink.c:2248
do_setlink+0xba4/0x3e10 net/core/rtnetlink.c:2382
rtnl_setlink+0x2a9/0x400 net/core/rtnetlink.c:2636
rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4665
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2455
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4683
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
netlink_sendmsg+0xa18/0xfd0 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:642 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:652
___sys_sendmsg+0x7fd/0x930 net/socket.c:2126
__sys_sendmsg+0x11d/0x290 net/socket.c:2164
__do_sys_sendmsg net/socket.c:2173 [inline]
__se_sys_sendmsg net/socket.c:2171 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2171
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x456b29
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f9706bf8c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f9706bf96d4 RCX: 0000000000456b29
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000004
RBP: 00000000009300a0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d3548 R14: 00000000004c8227 R15: 0000000000000000
Fixes: 87002b03baab ("net: introduce vlan_vid_[add/del] and use them instead of direct [add/kill]_vid ndo calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-and-tested-by: syzbot+bd051aba086537515cdb@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cancel pending work before freeing smsc75xx private data structure
during binding. This fixes the following crash in the driver:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: mutex_lock+0x2b/0x3f
<snipped>
Workqueue: events smsc75xx_deferred_multicast_write [smsc75xx]
task: ffff8caa83e85700 task.stack: ffff948b80518000
RIP: 0010:mutex_lock+0x2b/0x3f
<snipped>
Call Trace:
smsc75xx_deferred_multicast_write+0x40/0x1af [smsc75xx]
process_one_work+0x18d/0x2fc
worker_thread+0x1a2/0x269
? pr_cont_work+0x58/0x58
kthread+0xfa/0x10a
? pr_cont_work+0x58/0x58
? rcu_read_unlock_sched_notrace+0x48/0x48
ret_from_fork+0x22/0x40
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 602b74eda813 ("mlxsw: spectrum_switchdev: Do not leak RIFs
when removing bridge") I handled the case where RIFs created for VLAN
devices were not properly cleaned up when their real device (a bridge)
was removed.
However, I forgot to handle the case of the VLAN device itself being
removed. Do so now when the VLAN device is being unlinked from its real
device.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reported-by: Artem Shvorin <art@qrator.net>
Tested-by: Artem Shvorin <art@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to a hardware issue in Spectrum-2, the field event_type of the event
queue element (EQE) has become reserved. It was used to distinguish between
command interface completion events and completion events.
Use queue number to determine event type, as command interface completion
events are always received on EQ0 and mlxsw driver maps completion events
to EQ1.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David writes:
"Networking fixes:
1) Prefix length validation in xfrm layer, from Steffen Klassert.
2) TX status reporting fix in mac80211, from Andrei Otcheretianski.
3) Fix hangs due to TX_DROP in mac80211, from Bob Copeland.
4) Fix DMA error regression in b43, from Larry Finger.
5) Add input validation to xenvif_set_hash_mapping(), from Jan Beulich.
6) SMMU unmapping fix in hns driver, from Yunsheng Lin.
7) Bluetooh crash in unpairing on SMP, from Matias Karhumaa.
8) WoL handling fixes in the phy layer, from Heiner Kallweit.
9) Fix deadlock in bonding, from Mahesh Bandewar.
10) Fill ttl inherit infor in vxlan driver, from Hangbin Liu.
11) Fix TX timeouts during netpoll, from Michael Chan.
12) RXRPC layer fixes from David Howells.
13) Another batch of ndo_poll_controller() removals to deal with
excessive resource consumption during load. From Eric Dumazet.
14) Fix a specific TIPC failure secnario, from LUU Duc Canh.
15) Really disable clocks in r8169 during suspend so that low
power states can actually be reached.
16) Fix SYN backlog lockdep issue in tcp and dccp, from Eric Dumazet.
17) Fix RCU locking in netpoll SKB send, which shows up in bonding,
from Dave Jones.
18) Fix TX stalls in r8169, from Heiner Kallweit.
19) Fix locksup in nfp due to control message storms, from Jakub
Kicinski.
20) Various rmnet bug fixes from Subash Abhinov Kasiviswanathan and
Sean Tranchetti.
21) Fix use after free in ip_cmsg_recv_dstaddr(), from Eric Dumazet."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (122 commits)
ixgbe: check return value of napi_complete_done()
sctp: fix fall-through annotation
r8169: always autoneg on resume
ipv4: fix use-after-free in ip_cmsg_recv_dstaddr()
net: qualcomm: rmnet: Fix incorrect allocation flag in receive path
net: qualcomm: rmnet: Fix incorrect allocation flag in transmit
net: qualcomm: rmnet: Skip processing loopback packets
net: systemport: Fix wake-up interrupt race during resume
rtnl: limit IFLA_NUM_TX_QUEUES and IFLA_NUM_RX_QUEUES to 4096
bonding: fix warning message
inet: make sure to grab rcu_read_lock before using ireq->ireq_opt
nfp: avoid soft lockups under control message storm
declance: Fix continuation with the adapter identification message
net: fec: fix rare tx timeout
r8169: fix network stalls due to missing bit TXCFG_AUTO_FIFO
tun: napi flags belong to tfile
tun: initialize napi_mutex unconditionally
tun: remove unused parameters
bond: take rcu lock in netpoll_send_skb_on_dev
rtnetlink: Fail dump if target netnsid is invalid
...
|
|
The NIC driver should only enable interrupts when napi_complete_done()
returns true. This patch adds the check for ixgbe.
Cc: stable@vger.kernel.org # 4.10+
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This affects at least versions 25 and 33, so assume all cards are broken
and just renegotiate by default.
Fixes: 10bc6a6042c9 ("r8169: fix autoneg issue on resume with RTL8168E")
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-10-01
This pull request includes some fixes to mlx5 driver,
Please pull and let me know if there's any problem.
For -stable v4.11:
"6e0a4a23c59a ('net/mlx5: E-Switch, Fix out of bound access when setting vport rate')"
For -stable v4.18:
"98d6627c372a ('net/mlx5e: Set vlan masks for all offloaded TC rules')"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The incoming skb needs to be reallocated in case the headroom
is not sufficient to adjust the ethernet header. This allocation
needs to be atomic otherwise it results in this splat
[<600601bb>] ___might_sleep+0x185/0x1a3
[<603f6314>] ? _raw_spin_unlock_irqrestore+0x0/0x27
[<60069bb0>] ? __wake_up_common_lock+0x95/0xd1
[<600602b0>] __might_sleep+0xd7/0xe2
[<60065598>] ? enqueue_task_fair+0x112/0x209
[<600eea13>] __kmalloc_track_caller+0x5d/0x124
[<600ee9b6>] ? __kmalloc_track_caller+0x0/0x124
[<602696d5>] __kmalloc_reserve.isra.34+0x30/0x7e
[<603f629b>] ? _raw_spin_lock_irqsave+0x0/0x3d
[<6026b744>] pskb_expand_head+0xbf/0x310
[<6025ca6a>] rmnet_rx_handler+0x7e/0x16b
[<6025c9ec>] ? rmnet_rx_handler+0x0/0x16b
[<6027ad0c>] __netif_receive_skb_core+0x301/0x96f
[<60033c17>] ? set_signals+0x0/0x40
[<6027bbcb>] __netif_receive_skb+0x24/0x8e
Fixes: 74692caf1b0b ("net: qualcomm: rmnet: Process packets over ethernet")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The incoming skb needs to be reallocated in case the headroom
is not sufficient to add the MAP header. This allocation needs to
be atomic otherwise it results in the following splat
[32805.801456] BUG: sleeping function called from invalid context
[32805.841141] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[32805.904773] task: ffffffd7c5f62280 task.stack: ffffff80464a8000
[32805.910851] pc : ___might_sleep+0x180/0x188
[32805.915143] lr : ___might_sleep+0x180/0x188
[32806.131520] Call trace:
[32806.134041] ___might_sleep+0x180/0x188
[32806.137980] __might_sleep+0x50/0x84
[32806.141653] __kmalloc_track_caller+0x80/0x3bc
[32806.146215] __kmalloc_reserve+0x3c/0x88
[32806.150241] pskb_expand_head+0x74/0x288
[32806.154269] rmnet_egress_handler+0xb0/0x1d8
[32806.162239] rmnet_vnd_start_xmit+0xc8/0x13c
[32806.166627] dev_hard_start_xmit+0x148/0x280
[32806.181181] sch_direct_xmit+0xa4/0x198
[32806.185125] __qdisc_run+0x1f8/0x310
[32806.188803] net_tx_action+0x23c/0x26c
[32806.192655] __do_softirq+0x220/0x408
[32806.196420] do_softirq+0x4c/0x70
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RMNET RX handler was processing invalid packets that were
originally sent on the real device and were looped back via
dev_loopback_xmit(). This was detected using syzkaller.
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AON_PM_L2 is normally used to trigger and identify the source of a
wake-up event. Since the RX_SYS clock is no longer turned off, we also
have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and
that interrupt remains active up until the magic packet detector is
disabled which happens much later during the driver resumption.
The race happens if we have a CPU that is entering the SYSTEMPORT
INTRL2_0 handler during resume, and another CPU has managed to clear the
wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we
have the first CPU stuck in the interrupt handler with an interrupt
cause that has been cleared under its feet, and so we keep returning
IRQ_NONE and we never make any progress.
This was not a problem before because we would always turn off the
RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned
off as well, thus not latching the interrupt.
The fix is to make sure we do not enable either the MPD or
BRCM_TAG_MATCH interrupts since those are redundant with what the
AON_PM_L2 interrupt controller already processes and they would cause
such a race to occur.
Fixes: bb9051a2b230 ("net: systemport: Add support for WAKE_FILTER")
Fixes: 83e82f4c706b ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.19
First, and also hopefully the last, set of fixes for 4.19. All small
but still important fixes
mt76x0
* fix a bug when a virtual interface is removed multiple times
b43
* fix DMA error related regression with proprietary firmware
iwlwifi
* fix an oops which was a regression in v4.19-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX queue config for bonding master could be different from its slave
device(s). With the commit 6a9e461f6fe4 ("bonding: pass link-local
packets to bonding master also."), the packet is reinjected into stack
with skb->dev as bonding master. This potentially triggers the
message:
"bondX received packet on queue Y, but number of RX queues is Z"
whenever the queue that packet is received on is higher than the
numrxqueues on bonding master (Y > Z).
Fixes: 6a9e461f6fe4 ("bonding: pass link-local packets to bonding master also.")
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When FW floods the driver with control messages try to exit the cmsg
processing loop every now and then to avoid soft lockups. Cmsg
processing is generally very lightweight so 512 seems like a reasonable
budget, which should not be exceeded under normal conditions.
Fixes: 77ece8d5f196 ("nfp: add control vNIC datapath")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") regression with the `declance' driver, which caused
the adapter identification message to be split between two lines, e.g.:
declance.c: v0.011 by Linux MIPS DECstation task force
tc6: PMAD-AA
, addr = 08:00:2b:1b:2a:6a, irq = 14
tc6: registered as eth0.
Address that properly, by printing identification with a single call,
making the messages now look like:
declance.c: v0.011 by Linux MIPS DECstation task force
tc6: PMAD-AA, addr = 08:00:2b:1b:2a:6a, irq = 14
tc6: registered as eth0.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing continuation lines")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During certain heavy network loads TX could time out
with TX ring dump.
TX is sometimes never restarted after reaching
"tx_stop_threshold" because function "fec_enet_tx_queue"
only tests the first queue.
In addition the TX timeout callback function failed to
recover because it also operated only on the first queue.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the chip-specific hw_start functions set bit TXCFG_AUTO_FIFO
in register TxConfig. The original patch changed the order of some
calls resulting in these changes being overwritten by
rtl_set_tx_config_registers() in rtl_hw_start(). This eventually
resulted in network stalls especially under high load.
Analyzing the chip-specific hw_start functions all chip version from
34, with the exception of version 39, need this bit set.
This patch moves setting this bit to rtl_set_tx_config_registers().
Fixes: 4fd48c4ac0a0 ("r8169: move common initializations to tp->hw_start")
Reported-by: Ortwin Glück <odi@odi.ch>
Reported-by: David Arendt <admin@prnet.org>
Root-caused-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Tony Atkinson <tatkinson@linux.com>
Tested-by: David Arendt <admin@prnet.org>
Tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since tun->flags might be shared by multiple tfile structures,
it is better to make sure tun_get_user() is using the flags
for the current tfile.
Presence of the READ_ONCE() in tun_napi_frags_enabled() gave a hint
of what could happen, but we need something stronger to please
syzbot.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 13647 Comm: syz-executor5 Not tainted 4.19.0-rc5+ #59
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:dev_gro_receive+0x132/0x2720 net/core/dev.c:5427
Code: 48 c1 ea 03 80 3c 02 00 0f 85 6e 20 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b 6e 10 49 8d bd d0 00 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 59 20 00 00 4d 8b a5 d0 00 00 00 31 ff 41 81 e4
RSP: 0018:ffff8801c400f410 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff8618d325
RDX: 000000000000001a RSI: ffffffff86189f97 RDI: 00000000000000d0
RBP: ffff8801c400f608 R08: ffff8801c8fb4300 R09: 0000000000000000
R10: ffffed0038801ed7 R11: 0000000000000003 R12: ffff8801d327d358
R13: 0000000000000000 R14: ffff8801c16dd8c0 R15: 0000000000000004
FS: 00007fe003615700(0000) GS:ffff8801dac00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1f3c43db8 CR3: 00000001bebb2000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
napi_gro_frags+0x3f4/0xc90 net/core/dev.c:5715
tun_get_user+0x31d5/0x42a0 drivers/net/tun.c:1922
tun_chr_write_iter+0xb9/0x154 drivers/net/tun.c:1967
call_write_iter include/linux/fs.h:1808 [inline]
new_sync_write fs/read_write.c:474 [inline]
__vfs_write+0x6b8/0x9f0 fs/read_write.c:487
vfs_write+0x1fc/0x560 fs/read_write.c:549
ksys_write+0x101/0x260 fs/read_write.c:598
__do_sys_write fs/read_write.c:610 [inline]
__se_sys_write fs/read_write.c:607 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:607
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457579
Code: 1d b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fe003614c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457579
RDX: 0000000000000012 RSI: 0000000020000000 RDI: 000000000000000a
RBP: 000000000072c040 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe0036156d4
R13: 00000000004c5574 R14: 00000000004d8e98 R15: 00000000ffffffff
Modules linked in:
RIP: 0010:dev_gro_receive+0x132/0x2720 net/core/dev.c:5427
Code: 48 c1 ea 03 80 3c 02 00 0f 85 6e 20 00 00 48 b8 00 00 00 00 00 fc ff df 4d 8b 6e 10 49 8d bd d0 00 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 59 20 00 00 4d 8b a5 d0 00 00 00 31 ff 41 81 e4
RSP: 0018:ffff8801c400f410 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff8618d325
RDX: 000000000000001a RSI: ffffffff86189f97 RDI: 00000000000000d0
RBP: ffff8801c400f608 R08: ffff8801c8fb4300 R09: 0000000000000000
R10: ffffed0038801ed7 R11: 0000000000000003 R12: ffff8801d327d358
R13: 0000000000000000 R14: ffff8801c16dd8c0 R15: 0000000000000004
FS: 00007fe003615700(0000) GS:ffff8801dac00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1f3c43db8 CR3: 00000001bebb2000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the first part to fix following syzbot report :
console output: https://syzkaller.appspot.com/x/log.txt?x=145378e6400000
kernel config: https://syzkaller.appspot.com/x/.config?x=443816db871edd66
dashboard link: https://syzkaller.appspot.com/bug?extid=e662df0ac1d753b57e80
Following patch is fixing the race condition, but it seems safer
to initialize this mutex at tfile creation anyway.
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+e662df0ac1d753b57e80@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tun_napi_disable() and tun_napi_del() do not need
a pointer to the tun_struct
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In flow steering, if asked to, the hardware matches on the first ethertype
which is not vlan. It's possible to set a rule as follows, which is meant
to match on untagged packet, but will match on a vlan packet:
tc filter add dev eth0 parent ffff: protocol ip flower ...
To avoid this for packets with single tag, we set vlan masks to tell
hardware to check the tags for every matched packet.
Fixes: 095b6cfd69ce ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The code that deals with eswitch vport bw guarantee was going beyond the
eswitch vport array limit, fix that. This was pointed out by the kernel
address sanitizer (KASAN).
The error from KASAN log:
[2018-09-15 15:04:45] BUG: KASAN: slab-out-of-bounds in
mlx5_eswitch_set_vport_rate+0x8c1/0xae0 [mlx5_core]
Fixes: c9497c98901c ("net/mlx5: Add support for setting VF min rate")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If the peer device was already unbound, then do not attempt to modify
it's resources, otherwise we will crash on dereferencing non-existing
device.
Fixes: 5c65c564c962 ("net/mlx5e: Support offloading TC NIC hairpin flows")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Disable the clk during suspend to save power. Note that tp->clk may be
NULL, the clk core functions handle this without problems.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In regular NIC transmission flow, driver always configures MAC using
Tx queue zero descriptor as a part of MAC learning flow.
But with multi Tx queue supported NIC, regular transmission can occur on
any non-zero Tx queue and from that context it uses
Tx queue zero descriptor to configure MAC, at the same time TX queue
zero could be used by another CPU for regular transmission
which could lead to Tx queue zero descriptor corruption and cause FW
abort.
This patch fixes this in such a way that driver always configures
learned MAC address from the same Tx queue which is used for
regular transmission.
Fixes: 7e2cf4feba05 ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: e0e474a83c18 ("smsc95xx: add wol magic packet support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 6c636503260d ("smsc75xx: add wol magic packet support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 21ff2e8976b1 ("r8152: support WOL")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 19a38d8e0aa3 ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver supports a fair amount of Wake-on-LAN modes, but is not
checking that the user specified one that is supported.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Woojung Huh <Woojung.Huh@Microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: e2ca90c276e1 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 2e55cc7210fe ("[PATCH] USB: usbnet (3/9) module for ASIX Ethernet adapters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2018-09-28
An update from ieee802154 for your *net* tree.
Some cleanup patches throughout the drivers from the Huawei tag team
Yue Haibing and Zhong Jiang.
Xue is replacing some magic numbers with defines in his mcr20a driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ibmvnic uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
ibmvnic_netpoll_controller() was completely wrong anyway,
as it was scheduling NAPI to service RX queues (instead of TX),
so I doubt netpoll ever worked on this driver.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
sfc-falcon uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-By: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
sfc uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Acked-By: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ena uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Netanel Belgazal <netanel@amazon.com>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Zorik Machulsky <zorik@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
netxen uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
qlcnic uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
