summaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2011-09-28Merge git://github.com/davem330/netLinus Torvalds12-32/+68
* git://github.com/davem330/net: ipv6-multicast: Fix memory leak in IPv6 multicast. ipv6: check return value for dst_alloc net: check return value for dst_alloc ipv6-multicast: Fix memory leak in input path. bnx2x: add missing break in bnx2x_dcbnl_get_cap bnx2x: fix WOL by enablement PME in config space bnx2x: fix hw attention handling net: fix a typo in Documentation/networking/scaling.txt ath9k: Fix a dma warning/memory leak rtlwifi: rtl8192cu: Fix unitialized struct iwlagn: fix dangling scan request batman-adv: do_bcast has to be true for broadcast packets only cfg80211: Fix validation of AKM suites iwlegacy: do not use interruptible waits iwlegacy: fix command queue timeout ath9k_hw: Fix Rx DMA stuck for AR9003 chips
2011-09-27Merge branch 'for-davem' of git://git.infradead.org/users/linville/wirelessDavid S. Miller9-29/+42
2011-09-27Merge branch 'master' of git://git.infradead.org/users/linville/wireless ↵John W. Linville9-29/+42
into for-davem
2011-09-27bnx2x: add missing break in bnx2x_dcbnl_get_capShmulik Ravid1-0/+1
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-27bnx2x: fix WOL by enablement PME in config spaceDmitry Kravkov1-1/+9
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-27bnx2x: fix hw attention handlingDmitry Kravkov2-2/+16
Use register name to initialize attention mask Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-26ath9k: Fix a dma warning/memory leakMohammed Shafi Shajakhan1-1/+9
proper dma_unmapping and freeing of skb's has to be done in the rx cleanup for EDMA chipsets when the device is unloaded and this also seems to address the following warning which shows up occasionally when the device is unloaded Call Trace: [<c0148cd2>] warn_slowpath_common+0x72/0xa0 [<c03b669c>] ? dma_debug_device_change+0x19c/0x200 [<c03b669c>] ? dma_debug_device_change+0x19c/0x200 [<c0148da3>] warn_slowpath_fmt+0x33/0x40 [<c03b669c>] dma_debug_device_change+0x19c/0x200 [<c0657f12>] notifier_call_chain+0x82/0xb0 [<c0171370>] __blocking_notifier_call_chain+0x60/0x90 [<c01713bf>] blocking_notifier_call_chain+0x1f/0x30 [<c044f594>] __device_release_driver+0xa4/0xc0 [<c044f647>] driver_detach+0x97/0xa0 [<c044e65c>] bus_remove_driver+0x6c/0xe0 [<c029af0b>] ? sysfs_addrm_finish+0x4b/0x60 [<c0450109>] driver_unregister+0x49/0x80 [<c0299f54>] ? sysfs_remove_file+0x14/0x20 [<c03c3ab2>] pci_unregister_driver+0x32/0x80 [<f92c2162>] ath_pci_exit+0x12/0x20 [ath9k] [<f92c8467>] ath9k_exit+0x17/0x36 [ath9k] [<c06523cd>] ? mutex_unlock+0xd/0x10 [<c018e27f>] sys_delete_module+0x13f/0x200 [<c02139bb>] ? sys_munmap+0x4b/0x60 [<c06547c5>] ? restore_all+0xf/0xf [<c0657a20>] ? spurious_fault+0xe0/0xe0 [<c01832f4>] ? trace_hardirqs_on_caller+0xf4/0x180 [<c065b863>] sysenter_do_call+0x12/0x38 ---[ end trace 16e1c1521c06bcf9 ]--- Mapped at: [<c03b7938>] debug_dma_map_page+0x48/0x120 [<f92ba3e8>] ath_rx_init+0x3f8/0x4b0 [ath9k] [<f92b5ae4>] ath9k_init_device+0x4c4/0x7b0 [ath9k] [<f92c2813>] ath_pci_probe+0x263/0x330 [ath9k] Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-26rtlwifi: rtl8192cu: Fix unitialized structLarry Finger1-0/+1
Driver rtl8192cu assigns a new struct rtl_tcb_desc object, but fails to clear it. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> [2.6.39+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-26iwlagn: fix dangling scan requestJohannes Berg1-14/+16
If iwl_scan_initiate() fails for any reason, priv->scan_request and priv->scan_vif are left dangling. This can lead to a crash later when iwl_bg_scan_completed() tries to run a pending scan request. In practice, this seems to be very rare due to the STATUS_SCANNING check earlier. That check, however, is wrong -- it should allow a scan to be queued when a reset/roc scan is going on. When a normal scan is already going on, a new one can't be issued by mac80211, so that code can be removed completely. I introduced this bug when adding off-channel support in commit 266af4c745952e9bebf687dd68af58df553cb59d. Cc: stable@kernel.org [3.0] Reported-by: Peng Yan <peng.yan@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-26[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereferenceNeil Horman3-12/+42
This oops was reported recently: d:mon> e cpu 0xd: Vector: 300 (Data Access) at [c0000000fd4c7120] pc: d00000000076f194: .t3_l2t_get+0x44/0x524 [cxgb3] lr: d000000000b02108: .init_act_open+0x150/0x3d4 [cxgb3i] sp: c0000000fd4c73a0 msr: 8000000000009032 dar: 0 dsisr: 40000000 current = 0xc0000000fd640d40 paca = 0xc00000000054ff80 pid = 5085, comm = iscsid d:mon> t [c0000000fd4c7450] d000000000b02108 .init_act_open+0x150/0x3d4 [cxgb3i] [c0000000fd4c7500] d000000000e45378 .cxgbi_ep_connect+0x784/0x8e8 [libcxgbi] [c0000000fd4c7650] d000000000db33f0 .iscsi_if_rx+0x71c/0xb18 [scsi_transport_iscsi2] [c0000000fd4c7740] c000000000370c9c .netlink_data_ready+0x40/0xa4 [c0000000fd4c77c0] c00000000036f010 .netlink_sendskb+0x4c/0x9c [c0000000fd4c7850] c000000000370c18 .netlink_sendmsg+0x358/0x39c [c0000000fd4c7950] c00000000033be24 .sock_sendmsg+0x114/0x1b8 [c0000000fd4c7b50] c00000000033d208 .sys_sendmsg+0x218/0x2ac [c0000000fd4c7d70] c00000000033f55c .sys_socketcall+0x228/0x27c [c0000000fd4c7e30] c0000000000086a4 syscall_exit+0x0/0x40 --- Exception: c01 (System Call) at 00000080da560cfc The root cause was an EEH error, which sent us down the offload_close path in the cxgb3 driver, which in turn sets cdev->l2opt to NULL, without regard for upper layer driver (like the cxgbi drivers) which might have execution contexts in the middle of its use. The result is the oops above, when t3_l2t_get attempts to dereference L2DATA(cdev)->nentries in arp_hash right after the EEH error handler sets it to NULL. The fix is to prevent the setting of the NULL pointer until after there are no further users of it. The t3cdev->l2opt pointer is now converted to be an rcu pointer and the L2DATA macro is now called under the protection of the rcu_read_lock(). When the EEH error path: t3_adapter_error->offload_close->cxgb3_offload_deactivate Is exectured, setting of that l2opt pointer to NULL, is now gated on an rcu quiescence point, preventing, allowing L2DATA callers to safely check for a NULL pointer without concern that the underlying data will be freeded before the pointer is dereferenced. This has been tested by the reporter and shown to fix the reproted oops [nhorman: fix up unitinialised variable reported by Dan Carpenter] Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reviewed-by: Karen Xie <kxie@chelsio.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-21iwlegacy: do not use interruptible waitsStanislaw Gruszka5-13/+13
iwlegacy version of fix: commit effd4d9aece9184f526e6556786a94d335e38b71 Author: Johannes Berg <johannes.berg@intel.com> Date: Thu Sep 15 11:46:52 2011 -0700 iwlagn: do not use interruptible waits Since the dawn of its time, iwlwifi has used interruptible waits to wait for synchronous commands and firmware loading. This leads to "interesting" bugs, because it can't actually handle the interruptions; for example when a command sending is interrupted it will assume the command completed fully, and then leave it pending, which leads to all kinds of trouble when the command finishes later. Since there's no easy way to gracefully deal with interruptions, fix the driver to not use interruptible waits. This at least fixes the error iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD' I have seen in P2P testing, but it is likely that there are other errors caused by this. Cc: stable@kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-21iwlegacy: fix command queue timeoutStanislaw Gruszka1-0/+2
iwlegacy version of fix: commit 282cdb325aea4ebbc42ce753b47cc96145eb54bc Author: Johannes Berg <johannes.berg@intel.com> Date: Mon Sep 12 12:09:10 2011 -0700 iwlagn: fix command queue timeout If the command queue is constantly busy, which can happen in P2P, the hangcheck timer will frequently find a command in it and will eventually reset the device because nothing sets the timestamp for this queue when commands are processed. Fix this by setting the timestamp when a command completes. iwlegacy does not support P2P, but this patch fix possible unneeded hardware resets, hence is needed. Cc: stable@kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-21ath9k_hw: Fix Rx DMA stuck for AR9003 chipsRajkumar Manoharan1-1/+1
During the endurance testing, rx frames are not getting DMAd from MAC whereas pcu rx frame counters are getting updated properly. As per systems team input updated the initval to fix rx dma stuck issue. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-21ixgbe: fix possible null buffer errorJesse Brandeburg1-2/+2
It seems that at least one PPC machine would occasionally give a (valid) 0 as the return value from dma_map, this caused the ixgbe code to not work correctly. A fix is pending in the PPC tree to not return 0 from dma map, but we can also fix the driver to make sure we don't mess up in other arches as well. This patch is applicable to all current stable kernels. Ref: https://bugzilla.redhat.com/show_bug.cgi?id=683611 Reported-by: Neil Horman <nhorman@redhat.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Alexander Duyck <alexander.h.duyck@intel.com> CC: stable@kernel.org Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-21tg3: fix VLAN tagging regressionKasper Pedersen1-2/+0
commit 92cd3a17ce9c719abb4c28dee3438e0c641f8de4 tg3: Simplify tx bd assignments broke VLAN tagging on outbound packets. It ifdef'ed BCM_KERNEL_SUPPORTS_8021Q, but this is not set anywhere. So vlan never gets set, and all packets are sent with vlan=0. v2: We can just remove the test. vlan_tx_tag_present is valid regardless of whether the 802.1q module is built. Tested on BCM5721 rev 11. Signed-off-by: Kasper Pedersen <kernel@kasperkp.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20net: pxa168: Fix build errors by including interrupt.hTanmay Upadhyay1-0/+1
Commit a6b7a407865aab9f849dd99a71072b7cd1175116 removed linux/interrupt.h from netdevice.h. This fixes below build failure drivers/net/pxa168_eth.c: In function 'pxa168_eth_collect_events': drivers/net/pxa168_eth.c:866: error: 'IRQ_NONE' undeclared (first use in this function) drivers/net/pxa168_eth.c:866: error: (Each undeclared identifier is reported only once drivers/net/pxa168_eth.c:866: error: for each function it appears in.) drivers/net/pxa168_eth.c: At top level: drivers/net/pxa168_eth.c:913: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'pxa168_eth_int_handler' drivers/net/pxa168_eth.c: In function 'pxa168_eth_open': drivers/net/pxa168_eth.c:1133: error: implicit declaration of function 'request_irq' drivers/net/pxa168_eth.c:1133: error: 'pxa168_eth_int_handler' undeclared (first use in this function) drivers/net/pxa168_eth.c:1134: error: 'IRQF_DISABLED' undeclared (first use in this function) drivers/net/pxa168_eth.c:1160: error: implicit declaration of function 'free_irq' Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20netconsole: switch init_netconsole() to late_initcallLin Ming1-1/+7
Commit 88491d8(drivers/net: Kconfig & Makefile cleanup) causes a regression that netconsole does not work if netconsole and network device driver are build into kernel, because netconsole is linked before network device driver. Andrew Morton suggested to fix this with initcall ordering. Fixes it by switching init_netconsole() to late_initcall. Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20gianfar: Fix overflow check and return value for gfar_get_cls_all()Ben Hutchings1-4/+4
This function may currently fill one entry beyond the end of the array it is given. It also doesn't return an error code in case it does detect overflow. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20ppp_generic: fix multilink fragment MTU calculation (again)Henry Wong1-1/+6
When using MLPPP, the maximum size of a fragment is incorrectly calculated with an offset of -2. This patch reverses the changes in the patch found here: http://marc.info/?l=linux-netdev&m=123541324010539&w=2 The value of hdrlen includes the size of both the 2-byte PPP protocol field and the 2- or 4-byte multilink header (2+4=6 for long sequence numbers, 2+2=4 for short sequence numbers). Section 2 of RFC1661 says that the MRU that is negotiated (i.e., the MTU of the sending system) includes only the PPP payload but not the protocol field, thus the correct MTU should be the link's MTU minus the multilink header (mtu - (hdrlen-2)). The incorrect calculation causes Linux to fragment packets to a size two bytes smaller than the allowed MTU. While not technically illegal, this behaviour confounds MRU-tuning to avoid PPP-layer fragmentation. Signed-off-by: Henry Wong <henry@stuffedcow.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20GRETH: avoid overwrite IP-stack's IP-frags checksumDaniel Hellstrom1-2/+5
The GRETH GBIT core does not do checksum offloading for IP segmentation. This patch adds a check in the xmit function to determine if the stack has calculated the checksum for us. Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20GRETH: RX/TX bytes were never increasedDaniel Hellstrom2-0/+6
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20Merge branch 'davem.r8169.fixes' of git://violet.fr.zoreil.com/romieu/linuxDavid S. Miller1-5/+27
2011-09-20Merge branch 'master' of ssh://infradead/~/public_git/wireless into for-davemJohn W. Linville5-42/+73
2011-09-19b43: Fix beacon problem in ad-hoc modeManual Munz1-1/+2
In ad-hoc mode, driver b43 does not issue beacons. Signed-off-by: Manual Munz <freifunk@somakoma.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-18Merge git://github.com/davem330/netLinus Torvalds29-356/+603
* git://github.com/davem330/net: (62 commits) ipv6: don't use inetpeer to store metrics for routes. can: ti_hecc: include linux/io.h IRDA: Fix global type conflicts in net/irda/irsysctl.c v2 net: Handle different key sizes between address families in flow cache net: Align AF-specific flowi structs to long ipv4: Fix fib_info->fib_metrics leak caif: fix a potential NULL dereference sctp: deal with multiple COOKIE_ECHO chunks ibmveth: Fix checksum offload failure handling ibmveth: Checksum offload is always disabled ibmveth: Fix issue with DMA mapping failure ibmveth: Fix DMA unmap error pch_gbe: support ML7831 IOH pch_gbe: added the process of FIFO over run error pch_gbe: fixed the issue which receives an unnecessary packet. sfc: Use 64-bit writes for TX push where possible Revert "sfc: Use write-combining to reduce TX latency" and follow-ups bnx2x: Fix ethtool advertisement bnx2x: Fix 578xx link LED bnx2x: Fix XMAC loopback test ...
2011-09-17r8169: do not enable the TBI for anything but the original 8169.Francois Romieu1-3/+10
The TBI bit in PHYStatus is reserved on anything but the oldest 8169. Nobody complained after I disabled it for the 8168 and the 810x (see 66ec5d4fb1ce6f0bd9df4bc4b758f0916d9f37ab). Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Hayes Wang <hayeswang@realtek.com>
2011-09-17r8169: remove erroneous processing of always set bit.Francois Romieu1-1/+6
When set, RxFOVF (resp. RxBOVF) is always 1 (resp. 0). Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Hayes <hayeswang@realtek.com>
2011-09-17r8169: fix WOL setting for 8105 and 8111evlHayes Wang1-1/+9
rtl8105, rtl8111E, and rtl8111evl need enable RxConfig bit 1 ~ 3 for supporting wake on lan. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2011-09-17r8169: add MODULE_FIRMWARE for the firmware of 8111evlHayes Wang1-0/+1
Add MODULE_FIRMWARE for the firmware of RTL8111E-VL Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2011-09-17r8169: fix the reset setting for 8111evlHayes Wang1-0/+1
rtl8111evl should stop any TLP requirement before resetting by enabling register 0x37 bit 7. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2011-09-16can: ti_hecc: include linux/io.hDaniel Mack1-0/+1
This fixes a build breakage for OMAP3 boards. Signed-off-by: Daniel Mack <zonque@gmail.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: netdev@vger.kernel.org Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-16iwlagn: workaround bug crashing some APsDon Fry1-0/+5
This patch reverts commit 9b7688328422b88a7a15dc0dc123ad9ab1a6e22d which was introduced in 2.6.38-rc1. It works around a problem where the iwlagn driver stimulates a bug crashing (requiring power cycle to recover) some APs under heavy traffic. CC: stable@kernel.org #2.6.39, #3.0.0 #3.1.0 Signed-off-by: Don Fry <donald.h.fry@intel.com> SIgned-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-16rtl2800usb: Fix incorrect storage of MAC address on big-endian platformsLarry Finger1-8/+9
The eeprom data is stored in little-endian order in the rt2x00 library. As it was converted to cpu order in the read routines, the data need to be converted to LE on a big-endian platform. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-16rt2800pci: Fix compiler error on PowerPCLarry Finger1-13/+17
Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated if statement results in incorrect flow, whereas the equivalent switch statement works correctly. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-16ipw2x00: fix rtnl mutex deadlockStanislaw Gruszka2-20/+40
This fix regression introduced by: commit: ecb4433550f0620f3d1471ae7099037ede30a91e Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Fri Aug 12 14:00:59 2011 +0200 mac80211: fix suspend/resume races with unregister hw Above commit add rtnl_lock() into wiphy_register(), what cause deadlock when initializing ipw2x00 driver, which itself call wiphy_register() from register_netdev() internal callback with rtnl mutex taken. To fix move wiphy_register() outside register_netdev(). This solution have side effect of not creating /sys/class/net/wlanX/phy80211 link, but that's a minor issue we can live with. Bisected-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl> Bisected-by: Michael Witten <mfwitten@gmail.com> Tested-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl> Tested-by: Michael Witten <mfwitten@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-16ibmveth: Fix checksum offload failure handlingAnton Blanchard1-11/+20
Fix a number of issues in ibmveth_set_csum_offload: - set_attr6 and clr_attr6 may be used uninitialised - We store the result of the IPV4 checksum change in ret but overwrite it in a couple of places before checking it again later. Add ret4 to make it obvious what we are doing. - We weren't clearing the NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM flags if the enable of that hypervisor feature failed. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-16ibmveth: Checksum offload is always disabledAnton Blanchard1-1/+1
Commit b9367bf3ee6d (net: ibmveth: convert to hw_features) reversed a check in ibmveth_set_csum_offload that results in checksum offload never being enabled. Signed-off-by: Anton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # 3.0+ Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-16ibmveth: Fix issue with DMA mapping failureAnton Blanchard1-5/+5
descs[].fields.address is 32bit which truncates any dma mapping errors so dma_mapping_error() fails to catch it. Use a dma_addr_t to do the comparison. With this patch I was able to transfer many gigabytes of data with IOMMU fault injection set at 10% probability. Signed-off-by: Anton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # v2.6.37+ Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-16ibmveth: Fix DMA unmap errorBrian King1-1/+6
Commit 6e8ab30ec677 (ibmveth: Add scatter-gather support) introduced a DMA mapping API inconsistency resulting in dma_unmap_page getting called on memory mapped via dma_map_single. This was seen when CONFIG_DMA_API_DEBUG was enabled. Fix up this API usage inconsistency. Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Anton Blanchard <anton@samba.org> Cc: <stable@kernel.org> # v2.6.37+ Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-16Merge branch 'master' of ../netdev/David S. Miller2-15/+14
2011-09-15pch_gbe: support ML7831 IOHToshiharu Okada2-5/+16
Support new device OKI SEMICONDUCTOR ML7831 IOH(Input/Output Hub) ML7831 is for general purpose use. ML7831 is companion chip for Intel Atom E6xx series. ML7831 is completely compatible for Intel EG20T PCH. Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15pch_gbe: added the process of FIFO over run errorToshiharu Okada2-104/+179
This patch added the processing which should be done to hardware, when a FIFO over run error occurred. Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15pch_gbe: fixed the issue which receives an unnecessary packet.Toshiharu Okada1-7/+14
This patch fixed the issue which receives an unnecessary packet before link When using PHY of GMII, an unnecessary packet is received, And it becomes impossible to receive a packet after link up. Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15sfc: Use 64-bit writes for TX push where possibleBen Hutchings1-4/+5
This was originally done as part of commit 65f0b417dee94f779ce9b77102b7d73c93723b39 ("sfc: Use write-combining to reduce TX latency"), but that had to be reverted. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15Revert "sfc: Use write-combining to reduce TX latency" and follow-upsBen Hutchings7-88/+27
This reverts commits 65f0b417dee94f779ce9b77102b7d73c93723b39, d88d6b05fee3cc78e5b0273eb58c31201dcc6b76, fcfa060468a4edcf776f0c1211d826d5de1668c1, 747df2258b1b9a2e25929ef496262c339c380009 and 867955f5682f7157fdafe8670804b9f8ea077bc7. Depending on the processor model, write-combining may result in reordering that the NIC will not tolerate. This typically results in a DMA error event and reset by the driver, logged as: sfc 0000:0e:00.0: eth2: TX DMA Q reports TX_EV_PKT_ERR. sfc 0000:0e:00.0: eth2: resetting (ALL) Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15Merge branch 'for-davem' of git://git.infradead.org/users/linville/wirelessDavid S. Miller8-13/+34
2011-09-15bnx2x: Fix ethtool advertisementYaniv Rosner1-3/+40
Enable changing advertisement settings via ethtool. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15bnx2x: Fix 578xx link LEDYaniv Rosner1-2/+6
Fix 1G link LED for the BCM578xx-SFI/KR. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15bnx2x: Fix XMAC loopback testYaniv Rosner2-2/+2
Change XMAC loopback type from CORE LOCAL to LINE LOCAL for the BCM578xx due to intermittent problem with the loopback with this configuration. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15bnx2x: Remove fiber remote fault detectionYaniv Rosner1-8/+4
Remove remote fault detection as a tactic retreat due to link issues involved with it. Once issue is resolved, this feature will be restored again. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-04 06:13:10 +0000