| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We can't use SAR Geo if basic SAR is not enabled, since the SAR Geo
tables define offsets in relation to the basic SAR table in use.
To fix this, make iwl_mvm_sar_init() return one in case WRDS is not
available, so we can skip reading WGDS entirely.
Fixes: a6bff3cb19b7 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If the driver is unloaded when D3 debug data pulling is enabled
but not triggered, it doesn't release the data buffer.
Fix this by adding iwl_fw_runtime_free and calling it from the
relevant places.
Fixes: 2d8c261511ab ("iwlwifi: add d3 debug data support")
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When the firmware starts, it doesn't have any regulatory
information, hence it uses the world wide limitations. The
driver can feed the firmware with previous knowledge that
was kept in the driver, but the firmware may still not
update its internal tables.
This happens when we start a BSS interface, and then the
firmware can change the regulatory tables based on our
location and it'll use more lenient, location specific
rules. Then, if the firmware is shut down (when the
interface is brought down), and then an AP interface is
created, the firmware will forget the country specific
rules.
The host will think that we are in a certain country that
may allow channels and will try to teach the firmware about
our location, but the firmware may still not allow to drop
the world wide limitations and apply country specific rules
because it was just re-started.
In this case, the firmware will reply with MCC_RESP_ILLEGAL
to the MCC_UPDATE_CMD. In that case, iwlwifi needs to let
the upper layers (cfg80211 / hostapd) know that the channel
list they know about has been updated.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201105
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The oldest firmware supported by iwlmvm do support getting
the average beacon RSSI. Enable the sta_statistics() call
from mac80211 even on older firmware versions.
Fixes: 33cef9256342 ("iwlwifi: mvm: support beacon statistics for BSS client")
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
From coreboot/BIOS:
Name ("WGDS", Package() {
Revision,
Package() {
DomainType, // 0x7:WiFi ==> We miss this one.
WgdsWiFiSarDeltaGroup1PowerMax1, // Group 1 FCC 2400 Max
WgdsWiFiSarDeltaGroup1PowerChainA1, // Group 1 FCC 2400 A Offset
WgdsWiFiSarDeltaGroup1PowerChainB1, // Group 1 FCC 2400 B Offset
WgdsWiFiSarDeltaGroup1PowerMax2, // Group 1 FCC 5200 Max
WgdsWiFiSarDeltaGroup1PowerChainA2, // Group 1 FCC 5200 A Offset
WgdsWiFiSarDeltaGroup1PowerChainB2, // Group 1 FCC 5200 B Offset
WgdsWiFiSarDeltaGroup2PowerMax1, // Group 2 EC Jap 2400 Max
WgdsWiFiSarDeltaGroup2PowerChainA1, // Group 2 EC Jap 2400 A Offset
WgdsWiFiSarDeltaGroup2PowerChainB1, // Group 2 EC Jap 2400 B Offset
WgdsWiFiSarDeltaGroup2PowerMax2, // Group 2 EC Jap 5200 Max
WgdsWiFiSarDeltaGroup2PowerChainA2, // Group 2 EC Jap 5200 A Offset
WgdsWiFiSarDeltaGroup2PowerChainB2, // Group 2 EC Jap 5200 B Offset
WgdsWiFiSarDeltaGroup3PowerMax1, // Group 3 ROW 2400 Max
WgdsWiFiSarDeltaGroup3PowerChainA1, // Group 3 ROW 2400 A Offset
WgdsWiFiSarDeltaGroup3PowerChainB1, // Group 3 ROW 2400 B Offset
WgdsWiFiSarDeltaGroup3PowerMax2, // Group 3 ROW 5200 Max
WgdsWiFiSarDeltaGroup3PowerChainA2, // Group 3 ROW 5200 A Offset
WgdsWiFiSarDeltaGroup3PowerChainB2, // Group 3 ROW 5200 B Offset
}
})
When read the ACPI data to find out the WGDS, the DATA_SIZE is never
matched.
From the above format, it gives 19 numbers, but our driver is hardcode
as 18.
Fix it to pass then can parse the data into our wgds table.
Then we will see:
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init Sending GEO_TX_POWER_LIMIT
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[0]: chain A = 68 chain B = 69 max_tx_power = 54
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[1]: chain A = 48 chain B = 49 max_tx_power = 70
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[0]: chain A = 51 chain B = 67 max_tx_power = 50
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[1]: chain A = 69 chain B = 70 max_tx_power = 68
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[0]: chain A = 49 chain B = 50 max_tx_power = 48
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[1]: chain A = 52 chain B = 53 max_tx_power = 51
Cc: stable@vger.kernel.org # 4.12+
Fixes: a6bff3cb19b7 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The variables il->staging.filter_flags, rxon1->filter_flags and
rxon2->filter_flags need to be protected by the mutex lock il->mutex.
This patch adds a lock assertion of il->mutex to check whether
this lock is held.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access. This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We don't really need this state: instead of having an inactive
state where we can awaken zombie queues again if needed, just
keep them in their normal state unless a new queue is actually
needed and there's no other way of getting one.
We do this here by making the inactivity check not free queues
unless instructed that we now really need to allocate one to a
specific station, and in that case it'll just free the queue
immediately, without doing any inactivity step inbetween.
The only downside is a little bit more processing in this case,
but the code complexity is lower.
Additionally, this fixes a corner case: due to the way the code
worked, we could only ever reuse an inactive queue if it was
the reserved queue for a station, as iwl_mvm_find_free_queue()
would never consider returning an inactive queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We want to call iwl_mvm_inactivity_check() from here in the
next patch, so need to move the code down to be able to.
Fix a minor checkpatch complaint while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This function is only used in the file where it's declared,
so just make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Instead of iterating all the queues after having potentially
changed some queue configurations, rechecking if that was done,
mark the ones that do need a TID change explicitly in a bitmap
and use that to send the change to the firmware.
While at it, also rename iwl_mvm_change_queue_owner() to
iwl_mvm_change_queue_tid() since that's more obvious - the
"kind" of owner isn't immediately clear right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We set the queue to this state, only to pretty much immediately
move it out of it again. However, we can't even hit any of the
code that checks if the queue is reconfiguring, because all of
this happens under mvm->mutex and we hold the all the way from
marking the queue as RECONFIGURING to marking it as READY again.
Additionally, the queue that became RECONFIGURING would've been
in SHARED state before, and it can safely stay in that state. In
case of errors, it previously would have stayed in RECONFIGURING
which it could never have left again.
Remove the state entirely and just track the queues that need to
be reconfigured in a separate, local, bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We currently reconfigure the queues after the inactivity check,
but only in one of the two callers. This might leave queues in
a state where the TID owner is wrong, if called when reserving
a queue for a new station.
Clean this up and do the reconfiguration inside the inactivity
check function. This requires changing the locking, but one of
the two places already holds the mvm mutex and the other easily
can.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If TVQM is used we skip over this, move the code into a new
function to get rid of the label.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no need to build a bitmap first and then iterate,
just do the iteration with the right locking directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no need to have a hw refcount if we just mark the
command queue with a (fake) TID; at that point, the refcount
becomes equivalent to the hweight() of the TID bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
None of these functions really need to be separate, they're all
only used in sta.c, move them there and make them static.
Fix a small typo in related code while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Make this a named struct rather than an anonymous one,
we'll want to refer to it by name later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Move the rt status checking to the start of the resume flow in order
to avoid sending D0I3_END_CMD to the FW. Also, collect dump if an
assert was encountered.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Debug data dump is not working in flows that stop the device is used
in their error handling. During these flows the op mode mutex is
locked until the device stops. Because of that, any assert generated
from the firmware can be handled only after the device already
stopped.
Since dumping cannot occour after stopping the device, split the the
dump function to two parts, Part that handles locking, and the part
that starts the actual dumping and call the second part in the op mode
stop device function.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently in case of DCM with P2P GO where BSS DTIM interval < 220 msec
the fw fails to allocate events for the P2P GO dtim due to long passive
scan events.
Fix this by requesting all scans in this scenario to be fragmented with
fast balance scan time settings. The only exception is in case
fragmented scan was planned to be set due to low latency or high
throughput reason, set the scan timing as planned.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Fast balance scan is similar to SCAN_TYPE_MILD, but this scan is
fragmented and has shorter out of operating channel time,
and therefore better match low latency scenarios.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Split TX tracing to be per TB. This is needed now that
AMSDUs can be sent and skb can be larger than trace
limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we TX AMSDU, we shouldn't pad the packet. In the past,
we were building AMSDU only in transport layer, and gen2
functions are built based on this. However, now that op mode
may build AMSDUs, we need to take care of padding also in
gen2 "non-pcie-amsdu" path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed. Note that RSC is sent separately in
a new command. This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
iwl_fw_dbg_collect can be called by any function that already
has the error string ready. iwl_fw_dbg_collect_trig, on the
other hand, does string formatting. The occurrences decrement
is at iwl_fw_dbg_collect_trig, instead of iwl_fw_dbg_collect,
which causes it to sometimes be skipped. Move it to the right
location.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As preparation for new trigger format, make the function
agnostic to the trigger fomat. Instead it gets the relevant
parameters - id and delay.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.
Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add debugfs to send host command in mvm and fmac op modes.
Allows to send host command at runtime via send_hcmd debugfs file.
The command is received as a string that represents hex values.
The struct of the command is as follows:
[cmd_id][flags][length][data]
cmd_id and flags are 8 chars long each.
length is 4 chars long.
data is length * 2 chars long.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Bump the firmware API version to 41.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we use the iwl_pcie_txq_build_tfd() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The fall-through to the MVM case is intended as we have to do
*something* to continue, and can't easily clean up. So we'll
just fail in mvm later, if this does happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we use the iwl_pcie_gen2_set_tb() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Fixes: ab6c644539e9 ("iwlwifi: pcie: copy TX functions to new transport")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
With NICs that don't read the NVM directly and instead rely on getting
the relevant data from the firmware, the number of reserved MAC
addresses was not added to the API. This caused the driver to assume
there is only one address which results in all interfaces getting the
same address. Update the API to fix this.
While at it, fix-up the comments with firmware api names to actually
match what we have in the firmware.
Fixes: e9e1ba3dbf00 ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Trigger dump collection if the alive flow fails, regardless of the
reason.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In mac80211, the default remains for HT, so set the limit to
HE for our driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For SU/SU-ER/MU PPDUs we have spatial reuse.
For those where it's relevant we also know the pre-FEC
padding factor, PE disambiguity bit, beam change bit
and doppler bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add information about the LDCP extra symbol segment to the HE
data when applicable (not for trigger-based PPDUs).
While at it, clean up the code for UL/DL a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We have this data available, so add it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This code gets shorter if it doesn't have to check all the
conditions, so move it to an appropriate place that has all
of them validated already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Split the code out into a separate routine, and move that to be
called inside the previously introduced iwl_mvm_decode_he_phy_data()
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Pull some of the decoding of he_phy_data into a separate function so
we don't need to check over and over again if it's valid.
While at it, fix the UL/DL bit reporting to be for all but trigger-
based frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As detected by Luca during code review when I move this in the
next patch, the code here is putting the data into the wrong
field (flags1 instead of flags2). Fix that.
Fixes: e5721e3f770f ("iwlwifi: mvm: add radiotap data for HE")
Reported-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
