| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The triplet of get trigger, is trigger enabled and is trigger stopped
repeats itself. Group them in a function to avoid code duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
After switching to a new channel, driver schedules session protection
time event in order to hear the beacon on the new channel.
The duration of the protection is two beacon intervals.
However, since we start to switch slightly before beacon with count 1, in
case we don't hear (or AP doesn't transmit) the very first beacon on the
new channel the protection ends without hearing any beacon at all.
At this stage the switch is not complete, the queues are closed and the
interface doesn't have quota yet or TBTT events. As the result, we are
stuck forever waiting for iwl_mvm_post_channel_switch() to be called.
Fix this by increasing the protection time to be 3 beacon intervals and
in addition drop the connection if the time event ends before we got any
beacon.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
It was assumed that apply_time==0 implies immediate scheduling, which is
wrong. Instead, the fw expects the START_IMMEDIATELY flag to be set.
Otherwise, this resulted in 0x3063 assert.
Fix that.
While at it rename the T2_V2_START_IMMEDIATELY to
TE_V2_START_IMMEDIATELY.
Fixes: f5d8f50f271d ("iwlwifi: mvm: Fix channel switch in case of count <= 1")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the removal of non-DQA code, we don't need the queues
variable any more. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Before deleting a time event (remain-on-channel instance), flush
the queue so that frames cannot get stuck on it. We already flush
the AUX STA queues, but a separate station is used for the P2P
Device queue.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Since iwl_mvm_start_p2p_roc() is only called from iwl_mvm_roc(),
which already flushes the same work item, doing it again in it
is superfluous. Remove it and move the comment to the first one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If a time event is already scheduled when trying to schedule one for
channel switch, the code assumes the channel switch is already
scheduled and no further action is required.
However, it is possible that the scheduled time event is actually
for session protection (e.g. when the first beacon after association
contains the CSA IE). In this case the channel switch will not be
scheduled which will finally lead to disconnection.
Fix this by removing the old time event and schduling a new one for
the channel switch.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Move the notification wait code into the new fw interaction directory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Avoid using the global flush and move to flush per
station whenever possible in DQA mode.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently when the FW sends start/stop aux roc time event
notification with an error status, the driver returns an
error value, but does not remove the time event, and does
not notify the stack above that the time event is over.
This causes problems that the stack above assumes we are still
in the middle of a time event, and therefore can block different
events, such as scanning.
On FW failure notification, cleanup the time event parameters and
notify the stack above that the time event is over.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
iwl_mvm_restart_cleanup() calls ieee80211_remain_on_channel_expired()
on cleanup, but it doesn't clean the actual roc time
events, resulting in failure of further ROC attempts.
Refactor iwl_mvm_stop_roc() a bit, and add a new function
to only cleanup the roc time events (without sending further
commands).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The fw debug functionality is big enough to warrant
a separate file. Move existing related functions to the new file.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
