| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access. This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The new coex schema requires setting the non-shared antenna
for the single_stream_ant_msk field in the TLC command.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As with the non-offloaded rs case, during assoc on the ap side the phy
context is set to 20MHz until authorization of a client that supports
wider channel-widths. Support this by sending the initial
tlc_config_cmd with max supported channel width of 20MHz until
authorization succeeds.
Fixes: 6b7a5aea71b3 ("iwlwifi: mvm: always init rs with 20mhz bandwidth rates")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The parameter that indicated whether the LQ command should be sent
as sync or async was removed, causing the LQ command to be sent as
sync from interrupt context (e.g. from the RX path). This resulted
in a kernel warning: "scheduling while atomic" and failing to send
the LQ command, which ultimately leads to a queue hang.
Fix it by adding back the required parameter to send the command as
sync only when it is allowed.
Fixes: d94c5a820d10 ("iwlwifi: mvm: open BA session only when sta is authorized")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add support for the HE in the iwlwifi driver conforming with
P802.11ax_D2.0.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently, a BA session is opened when the tx traffic exceeds
10 frames per second. As a result of inter-op problems with some
APs, add a condition to open BA session only when station is
already authorized.
Fixes: 482e48440a0e ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support the new APIs and activate AMSDU based on the
offloaded TLC decisions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This aligns the code with the existing pattern to check
if the firmware has a certain capability.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Replace sprintf by scnprintf throughout rs code.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This patch adds rate scaling configuration command and
implements a few other handlers.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This patch introduces a new instance of rate_control_ops for
the new API (adding only empty stubs here and the subsequent
patches in the series will fill in the implementation).
The decision which API to use is done during the register
step according to FW TLV.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
New devices will have rate scaling algorithm running in the firmware.
With this feature, the driver's responsiblity is to provide an initial
configuration and to handle notifications regarding recent rates and
some other parameters. Debugfs hooks will be still available for
reading the current rate/statistics and setting a fixed rate.
The old API is supported so far, though both APIs cannot be used
simultaneously.
This is the first patch in the series. It adds a new TLV specifying
FW support for the new API and updates lq_sta to support two types
of rate scaling.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we are in a search cycle, we try different combinations
of parameters. Those combinations are called 'columns'.
When we switch to a new column, we first need to check if
this column has a suitable rate, if not, we can't try it.
This means we must not erase the statistics we gathered
for the previous column until we are sure that we are
indeed switching column.
The code that tries to switch to a new column first sets
a whole bunch of things for the new column, and only then
checks that we can find suitable rates in that column.
While doing that, the code mistakenly erased the rate
statistics. This code was right until
struct iwl_scale_tbl_info grew up for TPC.
Fix this to make sure we don't erase the rate statistics
until we are sure that we can indeed switch to the new
column.
Note that this bug is really harmless since it causes a
change in the behavior only when we can't find any rate
in the new column which should really not happen. In the
case we do find a suitable we reset the rate statistics
a few lines later anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't plan to have products with 3 antennas in the near
future. All the rest of the code follows the same
assumption as well.
Remove the support for antenna C from rs_toggle_ant.
When trying to toggle from ANT_B, this avoids to go through
ANT_C, discover that it doesn't exist and continue to ANT_A.
In MIMO, this avoids to do ANT_AB -> ANT_BC -> ANT_AC and
back to ANT_AB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add a new state to enum iwl_mvm_agg_state, which is used between
queueing the work that starts tx aggregations and actually starting that
work (changing to state IWL_AGG_STARTING).
This solves a race where ieee80211_start_tx_ba_session is called a
second time, before the work queued by the first run has a chance to
change the agg_state. In this case the second call to
ieee80211_start_tx_ba_session returns an error, and the fallback is to
abort the ba session start.
Fixes: 482e48440a0e ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Stephen Rothwell reported quite a few conflicts in iwlwifi between
wireless-drivers and wireless-drivers-next. To avoid any problems later in
other trees merge w-d to w-d-next to fix those conflicts early.
|
|
Tx BA session should be started according to the current throughput
without any dependence on the internal rate scaling state. The criteria
for opening a BA session will be 10 frames per second.
Sending frequent del BAs can cause inter-op issues with some APs. We'll
not close a BA session until we receive an explicit del BA from the
peer.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We use mvmsta for the sta->drv_priv in mvm, but in rs.c we have a
bunch of instances using sta_priv, which is probably due to it being
copied from dvm. Change all occurrences to mvmsta for consistency
with the rest of the driver
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Statistics should be collected according to the actual rate a
frame/aggregation was transmitted and not according to the initial rate
from the last LQ command (these rates are different if the frames were
retransmitted at a lower rate from the rate scale table).
This is needed to remove throughput degradation.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case that rate's antenna is wrong at the init stage, it's
very hard to say what went wrong. Add debug data to the already
existing WARN_ON_ONCE.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Up until now, the driver was comparing the rate reported by the FW and
the rate of the latest LQ command to avoid processing data belonging
to the old LQ command. Recently, FW changed the meaning of the initial
rate field in tx response and it holds the actual rate (which is not
necessarily the initial rate of LQ's rate table). Use instead LQ cmd
color to be able to filter out tx responses/BA notifications which
where sent during earlier LQ commands' time frame.
This fixes some throughput degradation in noisy environments.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Rates were changed to adapt to HE. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In https://bugzilla.kernel.org/show_bug.cgi?id=177341 Bob
reported a UBSAN WARNING on rs.c in iwldvm.
Fix the same bug in iwlmvm.
This because
i = index - 1;
for (mask = (1 << i); i >= 0; i--, mask >>= 1)
is unsafe: i could be negative and hence we can call <<
on a negative value.
This bug doesn't have any real impact since the condition
of the for loop will prevent any usage of mask.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177341
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Handling of the number of space time streams was missing for HT rate in
rate printing function. Fix it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Commit 5fc0f76c4 introduced Rx stats from debugfs, the function
iwl_mvm_reset_frame_stats from that commit defines and sets mcs but
does not use it. Compiling iwlwifi with W=1 gives this warning -
iwlwifi/mvm/rs.c: In function ‘iwl_mvm_update_frame_stats’:
iwlwifi/mvm/rs.c:3074:14: warning: variable ‘mcs’ set but not used [-Wunused-but-set-variable]
Fixes: 5fc0f76c43bd (iwlwifi: mvm: add Rx frames statistics via debugfs)
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
mvmvif is defined and set in rs_mimo_allow but not used. Compiling
iwlwifi with W=1 gives the following warning, remove it. mvmsta is
used only to obtain mvmvif so remove it as well.
iwlwifi/mvm/rs.c: In function 'rs_mimo_allow':
iwlwifi/mvm/rs.c:165:22: warning: variable 'mvmvif' set but not used.[-Wunused-but-set-variable]
This fix removes calls to iwl_mvm_sta_from_mac &
iwl_mvm_vif_from_mac. They are both accessors, and do not have any
side-effects. Commit e621c2282e31 ("iwlwifi: rs: Remove workaround
that disables MIMO on P2P") removed a workaround that disabled MIMO on
P2P, 'mvmvif' was used for that workaround, but not removed with it.
Fixes: e621c2282e31 ("iwlwifi: rs: Remove workaround that disables MIMO on P2P")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Emmanuel Grumbach <emmmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently we try to open an aggregation for every packet (given that one
is not already open).
This causes redundant overhead (addba/delba) for null data packets.
Do not open an aggregation for null data packets.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow A-MSDU only when we are not downscaling and the
initial MCS is at least 5.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Klocwork is unhappy as ht_vht_rates might be accessed with
rate->index being set to values between 0 and 3 which will
lead to accessing uninitialized array elements. Effectively this
doesn't happen as in HT/VHT we're not using these rate indices.
Still fix this.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
These are a few fixes for the current cycle.
3 out of the 5 patches fix a bugzilla.
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value
|
|
Decreasing Tx power is allowed only when success ratio is
above the threshold defined in the algorithm. Add this condition.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
FW behaviour changed and now updates driver about the used TPC
reduction in the following cases:
1. In tx response, which is used mostly for a single frame case
2. In BA notification
When tx aggregation fails with the initial rate, FW will send
to the driver BA notification and will try to transmit with the
next rate, but this time without tx power reduction. Thus, in case
of a failure with the initial rate, driver will get two BA notifications,
the first one with reduced tx power as in the LQ command and the second
one with 0 power reduction.
This patch adapts the TPC statistics according to the description above:
1. Use BA notifications instead of Tx response
2. For TPC only, drop the optimization which considers empty BA as one
MPDU. The reason is that with TPC we want to recover very quickly from
a bad power reduction and, therefore we'd like the success ratio to get
an immediate hit when failing to get a BA, so we'd switch back to a
lower or zero power reduction
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Klocwork pointed these out. There is a theoretical possibility
that rate->index might be set to IWL_RATE_INVALID (15).
This could trigger an out of bounds access on ht_vht_rates or
legacy_rates arrays. Fix it by adding some checks.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Extend the configurable option of setting initial rate to RSSI based.
Make the initial rate to be set to VHT/HT SISO or legacy depending on
the AP capabilities.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
WARN_ON_ONCE() doesn't take a message, it only takes a condition. I
have changed this to WARN(1, ...).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This was an old workaround for solving latency issues with
certain Miracast adapters like ActionTec. However this isn't
needed anymore and furthermore it hurts throughput in other
use cases.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
