| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
HALP ICR is set as long as the FW should stay awake.
To prevent its multiple handling the driver masks this IRQ bit.
However, if there is a different MISC ICR before the driver clears
this bit, there is a risk of race condition between HALP mask and
unmask. This race leads to HALP timeout, in case it is mistakenly
masked.
Add an atomic flag to indicate if HALP ICR should be handled.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Upon status ring handling, in case there are both unicast and
multicast (cid == max) status messages to handle, wrong sta statistics
might get updated.
Fix this by setting stats to NULL upon invalid cid
(e.g. == max_assoc_sta).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Rearrange the code by having functions to access 802.3 header
members, source and destination addresses.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
New FW added support for upto 20 clients in AP mode. Change the driver
to support this as well. FW reports it's max supported associations in
WMI_READY_EVENT. Some WMI commands/events use cidxtid field which is
limited to 16 cids. Use new cid/tid fields instead.
For Rx packets cid from rx descriptor is limited to 3 bits (0..7),
to find the real cid, compare transmitter address with the stored
stations mac address in the driver sta array.
EDMA FW still supports 8 stations. Extending the support to 20
stations will come later.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In AP mode with multiple clients, driver stops net queue
(netif_tx_stop_queue) upon first ring (serving specific client)
becoming full. This can have negative effect on transmission to
other clients which may still have room in their corresponding rings.
Implement new policy in which stop/wake net queue are not used. In
case there is no room in the ring for a transmitted packet, drop the
packet.
New policy can be helpful to debug performance issues, to guarantee
maximum utilization of net queues.
New policy is disabled by default and can be enabled by debugfs:
echo 1 > drop_if_ring_full
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Due to a HW issue in PHY info collection rtap_include_phy_info is not
in use, hence can be removed.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e88975ca37d1 ("ath10k: dump tx stats in rate table format")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The NSS data is updated incorrectly in the tx stats as the array
indexing starts from zero.
Fix the incorrect updation of NSS data in tx_stats by taking into
consideration the array index starting from zero.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/recv.c: In function 'ath_rx_count_airtime':
drivers/net/wireless/ath/ath9k/recv.c:1010:18: warning:
variable 'acq' set but not used [-Wunused-but-set-variable]
It's not used after 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling
and airtime APIs"). Also remove related variables.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
SPUR DOWN field returns spurup instead of spurdown.
Signed-off-by: Andrea Greco <a.greco@4sigma.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since ath9k reports airtime usage directly using the
ieee80211_report_airtime() callback, it shouldn't also report it using the
tx_time in status. Make sure the field is zeroed before TX status is
reported to avoid spurious airtime being accounted by bits being left over
from earlier uses of the cb.
Fixes: 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 firmware versions WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 & onwards
supports maximum 33 peers including self peer. To support maximum peers,
send updated peer param to firmware during initialization.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The calibration data fetch will trigger sdio error, then sdio will
become fail untill reboot system.
If happens when run ifconfig wlan down, then ifconfig wlan up will
fail untill reboot system.Remove it fix the ifconfig wlan issue.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.
Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da49733e "ath10k: wmi: add management tx by reference support over wmi"
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware does not provide RSSI value to the host, it's only set to
zero. In that case don't report the value to mac80211. One risk here is that
value zero might be a valid value with other firmware, currently there's no way
to detect that.
Without the fix, the rssi value indicated by iw changes between the actual
value and -95.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The target device needs to be reset during power_down(), otherwise only the
first power_up() will work. And as ath10k calls power_up() during driver
initialisation the driver would be otherwise unusable.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware may turn it on based on scratch registers so disable the
firmware log to avoid that.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware does not allow transmitting packets with the
reduced tx completion HI_ACS option. SDIO firmware uses 1544 as
alternate credit size, which is not big enough for the maximum sized
mac80211 frames. Disable both these HI_ACS flags for SDIO.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a theoretical fix, the issue is found in code review.
When adding the host memory chunks into wmi-tlv init command,
there is no separate tlv header for each host memory chunk
in the struct array, which breaches the convention between
host and firmware, will result in mismatch between the two.
To fix this issue, add separate tlv headers for the host
memory chunks in wmi-tlv init command.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently after enabling the WMI debug logging,
there is no detail printed about the param id
and the param value for the pdev, vdev and
peer params which are set.
Enhance the WMI logging to print the param id
and the param value for pdev, vdev and peer set
param wmi commands.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "data" tx completion event. Host extracts ack rssi
values of data packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "management" tx completion event. Host extracts ack
rssi values of management packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When the driver receives the tx completion of the
descriptor over ce, it clears the nbytes configured
for that particular descriptor. WCN3990 uses ce
descriptors with 64-bit address.
Currently during handling the tx completion of the
descriptors, the nbytes are accessed from the descriptors
using ce_desc for 32-bit targets. This will lead to clearing
of memory at incorrect offset if DMA MASK is set to greater
than 32 bits.
Attach different ce tx copy completed handler for targets
using address above 32-bit address.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for 5.1. Major changes:
ath10k
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having
WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
|
|
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f56 ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes checkpatch warnings:
Prefer 'unsigned long' over 'unsigned long int' as the int is unnecessary
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The parameter order for clamp is supposed to be clamp(value, low, high).
When we write it in this order it's equivalent to
min(head->plcp[3] & 0x7f, 75) which works in this context where the min
is zero. But it's not a correct use of the API.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Instead of copying fields one by one copy the whole structure. This way there's
no need to modify the function every time we add a new field to the struct.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With W=1 there's a warning:
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'new' not described in 'ath10k_wow_convert_8023_to_80211'
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'old' not described in 'ath10k_wow_convert_8023_to_80211'
Fix it by changing the documentation marker '/**' to a normal code comment.
While at it, clean up the line wrapping.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With W=1 GCC warns:
drivers/net/wireless/ath/ath10k/htt.h:1746:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_32' is less than 4 [-Wpacked-not-aligned]
drivers/net/wireless/ath/ath10k/htt.h:1753:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_64' is less than 4 [-Wpacked-not-aligned]
Fix that by using __align(4). Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
wmi.h does not use anything from mac80211.h so change it to include only
ieee80211.h.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When adding a new value to enum wmi_service it's very easy to miss that the new
value should be also added to wmi_service_name() mapping function. Modify the
function so that GCC can now warn about this:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_FOO' not handled in switch [-Wswitch]
And also add a reminder to the enum.
Thanks to Jouni Malinen for the idea.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
After implementing the next patch GCC reported:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BTCOEX' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_MGMT_TX_WMI' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_SPOOF_MAC_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_THERM_THROT' not handled in switch [-Wswitch]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If supported, update transmit airtime in mac80211 with the airtime
values reported by the firmware. TX airtime of the PPDU is reported
via HTT data TX completion indication message.
A new service flag 'WMI_SERVICE_REPORT_AIRTIME' is added to advertise
the firmware support. For firmwares which do not support this feature,
TX airtime is calculated in the driver using TX bitrate.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.6.1-00841
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Multicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending software encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic (per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted in
software and pushed to the target with encap mode set to RAW in the TX
descriptors.
Not all firmwares can support this type of key configuration(having few
keys installed in hardware and few only in software); for this purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw mode.
Hardwares Tested : QCA9984, QCA988X
Firmwares Tested : 10.4-3.5.3-00057, 10.2.4-1.0-00042
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This moves the ath9k driver to use the mac80211 TXQ scheduling and
airtime accounting APIs, removing the corresponding state tracking
inside the driver.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch error and warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Commit 750afb08ca71 ("cross-tree: phase out dma_zalloc_coherent()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/ce.c:1602: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: b7ba83f7c414 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The support to put WCN3990 firmware into Factory
test mode is not present currently. The WCN3990
firmware can operate in Factory test mode based
on the mode it receives in the wlan enable message
from the host driver.
When the host driver is started in testmode send
the operating mode as UTF mode, to the WCN3990
firmware, in the wlan enable message to start the
firmware in Factory test mode.
Tested on: WCN3990
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The DIAG copy engine is only used via polling, but it holds a spinlock
with softirqs disabled. Each iteration of our read/write loops can
theoretically take 20ms (two 10ms timeout loops), and this loop can be
run an unbounded number of times while holding the spinlock -- dependent
on the request size given by the caller.
As of commit 39501ea64116 ("ath10k: download firmware via diag Copy
Engine for QCA6174 and QCA9377."), we transfer large chunks of firmware
memory using this mechanism. With large enough firmware segments, this
becomes an exceedingly long period for disabling soft IRQs. For example,
with a 500KiB firmware segment, in testing QCA6174A, I see 200 loop
iterations of about 50-100us each, which can total about 10-20ms.
In reality, we don't really need to block softirqs for this duration.
The DIAG CE is only used in polling mode, and we only need to hold
ce_lock to make sure any CE bookkeeping is done without screwing up
another CE. Otherwise, we only need to ensure exclusion between
ath10k_pci_diag_{read,write}_mem() contexts.
This patch moves to use fine-grained locking for the shared ce_lock,
while adding a new mutex just to ensure mutual exclusion of diag
read/write operations.
Tested on QCA6174A, firmware version WLAN.RM.4.4.1-00132-QCARMSWPZ-1.
Fixes: 39501ea64116 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
FW credit flow control is enabled for only WMI ctrl
service(CE3) but credit update is requested unconditionally
on all HTC services as part of HTC tx in CE3/CE0/CE4.
This is causing WOW failure as FW is not expecting credit
report request on other end-points(CE0/CE4).
Request credit report only on those endpoints where
credit flow control is enabled.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Register snoc bus layer suspend/resume PM ops and configure
the wakeup source(CE2) for the device.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
