| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Call cfg80211_inform_bss_frame_data to report cfg80211 on the
boottime_ns in order to prevent the scan results filtering due to
aging.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
cid value is not being verified in wmi_evt_delba(),
verification is added.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix a race between cfg80211 add_key call and transmitting of 4/4 EAP
packet. In case the transmit is delayed until after the add key takes
place, message 4/4 will be encrypted with the new key, and the
receiver side (AP) will drop it due to MIC error.
Wil6210 will monitor and look for the transmitted packet 4/4 eap key.
In case add_key takes place before the transmission completed, then
wil6210 will let the FW store the key and wil6210 will notify the FW
to use the PTK key only after 4/4 eap packet transmission was
completed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11.
wil6210 reports it's EDMG capabilities (that are also based on FW
capability) to cfg80211 by filling
wiphy->bands[NL80211_BAND_60GHZ]->edmg_cap.
wil6210 handles edmg.channels and edmg.bw_config requested in connect
and start_ap operations.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This change fixes a rare race condition of handling WMI events after
wmi_call expires.
wmi_recv_cmd immediately handles an event when reply_buf is defined and
a wmi_call is waiting for the event.
However, in case the wmi_call has already timed-out, there will be no
waiting/running wmi_call and the event will be queued in WMI queue and
will be handled later in wmi_event_handle.
Meanwhile, a new similar wmi_call for the same command and event may
be issued. In this case, when handling the queued event we got WARN_ON
printed.
Fixing this case as a valid timeout and drop the unexpected event.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Replace all wmi_call timeouts that are less than 100 msec to use
WIL_WMI_CALL_GENERAL_TO_MS (100 msec) as a default. Some of the
current wmi_call timeouts are too short and fails to receive its
waiting events.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Base-band chips support multi RFs chips. Add support for reading
multiple RFs temperature via debugfs.
Signed-off-by: Tzahi Sabo <stzahi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Set max_msdu_size in WMI_BCAST_DESC_RING_ADD_CMD to allow FW
to optimize the buffers allocation for bcast packets.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
RBUFCAP support added in FW.
The RBUFCAP feature is amendment to the block ack mechanism to
prevent overloading of the recipient’s memory space, which may
happen in case the link speed is higher than STA’s capability
to process or consume incoming data.
The block ack policy (ba_policy) is now controlled by FW so driver
should ignore this field.
Add new debugfs "rbufcap" to configure RBUFCAP.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Save the parameter of max_assoc_sta per device.
On fw_ready event calculate the max_assoc_sta and save it per device,
do not overwrite the max_assoc_sta module param.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The functions that send management TX frame have 3 possible
results: success and other side acknowledged receive (ACK=1),
success and other side did not acknowledge receive(ACK=0) and
failure to send the frame. The current implementation
incorrectly reports the ACK=0 case as failure.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Check that the mid is valid and that it does not exceed the memory
size allocated to vifs array.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In case there are connected stations, FW needs to disconnect
them before handling PCP stop. This flow can take several
seconds.
Increasing PCP stop timeout to 5 seconds to allow that.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
New FW added support for upto 20 clients in AP mode. Change the driver
to support this as well. FW reports it's max supported associations in
WMI_READY_EVENT. Some WMI commands/events use cidxtid field which is
limited to 16 cids. Use new cid/tid fields instead.
For Rx packets cid from rx descriptor is limited to 3 bits (0..7),
to find the real cid, compare transmitter address with the stored
stations mac address in the driver sta array.
EDMA FW still supports 8 stations. Extending the support to 20
stations will come later.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Due to a HW issue in PHY info collection rtap_include_phy_info is not
in use, hence can be removed.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Switch from spin_lock to spin_lock_irqsave, because
wmi_ev_lock is used inside interrupt handler.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Initialize unset variable, and verify that mid is valid.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
wil6210 used to notify cfg80211_del_sta on every fw disconnect event.
In disable_ap_sme mode the userspace manages the protocol SME and
FW sends disconnect event only due to link loss.
In disable_ap_sme mode, indicate CQM packet loss to let the host
control the connection and disconnect the link if needed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Separate sending command to the fw from the event handling function to
simplify the disconnect flow and track the from_event flag correctly.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The comparison of cid >= 0 is always true because cid is of type u8
(8 bits, unsigned).
Fix this by removing such comparison and updating the type of
variable cid to u8 in the caller function.
Addresses-Coverity-ID: 1473079 ("Unsigned compared against 0")
Fixes: b9010f105f21 ("wil6210: add FT roam support for AP and station")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This feature is needed for enterprise APs and clients to enable
fast roaming as defined in 802.11r between APs in the same ESS.
On AP side, this feature is supported only when disable_ap_sme
is enabled.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently wil6210 ignores the channel field in the
cfg80211_mgmt_tx_params struct for wil_cfg80211_ops mgmt_tx operation
and sends all management frames on the serving channel.
Add support for off-channel transmission of management frames
(WIPHY_FLAG_OFFCHAN_TX) in AP mode. This is useful in enterprise APs
for sending custom probe request frames.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Driver can request FW to report link statistics using
WMI_LINK_STATS_CMDID.
FW will report statistics with WMI_LINK_STATS_EVENTID.
Two categories of statistics defined: basic and global.
New "link_stats" debugfs is used for requesting basic statistics
report (write) and for reading the basic statistics (read).
"link_stats_global" debugfs is used for requesting and reading the
global statistics.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In some cases where the device is stuck, reading from OTP
can timeout. As OTP section is known there is no need to read
it during device crash dump collection.
Adding a new field to struct fw_map to indicate if to include
this section in crash dump collection.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enhanced DMA RX data path is handled using a single
RX descriptor ring for all VIFs.
Multiple RX status rings are supported, to allow RSS
and multi MSI support.
The driver gets the RX completions via the RX status rings.
The RX status message includes the completed RX buffer ID,
which points to the allocated SKB.
The enhanced DMA RX data flow supports RX chaining, where
multiple SKBs are merged into a single packet.
Enhanced DMA HW supports RX HW reorder offload, enabled by
default for Talyn-MB.
amsdu_en debugfs entry was added to allow control MSDU aggregation.
Use the following command to disable AMSDU (enabled by default):
echo 0 > amsdu_en
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enhanced DMA design includes the following rings:
- Single RX descriptor ring is used for all VIFs
- Multiple RX status rings are supported, to allow RSS
- TX descriptor ring is allocated per connection
- A single TX status ring is used for all TX descriptor rings
This patch initializes and frees the above descriptor and
status rings.
The RX SKBs are handled by a new entity of RX buffers manager,
which handles RX buffers, each one points to an allocated SKB.
During Rx completion processing, the driver extracts a buffer
ID which is used as an index to the buffers array.
After the SKB is freed the buffer is moved from the 'active'
list to the 'free' list, indicating it can be used for another
descriptor. During Rx refill, SKBs are allocated and attached
to 'free' buffers. Those buffers are attached to new descriptors
and moved to the 'active' list.
New debugfs entries were added to allow edma configuration:
Run the following command to configure the number of status rings:
echo NUM_OF_STATUS_RINGS > num_rx_status_rings
Run the following command to use extended RX status message for
additional debug fields from HW:
echo 0 > compressed_rx_status
Run the following command to control the size of the TX status ring:
echo TX_STATUS_RING_ORDER > tx_status_ring_order
The status ring size will be 1 << tx_status_ring_order
Run the following command to control the size of the RX status ring:
echo RX_STATUS_RING_ORDER > rx_status_ring_order
Due to HW constrains RX sring order should be bigger than RX ring order
The status ring size will be 1 << rx_status_ring_order
Run the following command to change the number of RX buffer IDs:
echo RX_BUFF_ID_COUNT > rx_buff_id_count
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In enhanced DMA the vrings are handled internally by the FW
and are not exposed to the driver.
Instead, the driver handles descriptor rings, which are mapped
by the FW to vrings.
The completions of the TX and RX descriptors are notified to
the driver using status rings. Each status ring descriptor
includes information of the completed descriptors and the ring id
of their descriptor ring.
This patch changes struct vring to generic wil_ring to allow
its reuse for enhanced DMA descriptor rings and adds the descriptor
and status rings specific descriptors.
The vring debugfs entries have changed as follows:
- dbg_vring_index has changed to dbg_ring_index
- vrings has changed to rings
- vring_idle_trsh has changed to ring_idle_trsh
- vring_index has changed to ring_index
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add changes to support initialization of Talyn-MB wil6210
device:
- Add definition for Talyn-MB new JTAG id
- Define talyn_mb_fw_mapping array
- Add Talyn-MB reset sequence
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for 4.18. Major changes:
ath10k
* add quiet mode support for QCA6174/QCA9377
wil6210
* disable WIL6210_TRACING kconfig option by default
|
|
WMI command reply saved in uninitialized struct.
In order to avoid accessing unset values from FW initialize
the reply struct.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Rearrange the code by having new function wmi_mgmt_tx() to take care
of the WMI part of wil_cfg80211_mgmt_tx().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Change the type of the argument reply_size from u8 to
u16 in order to support reply sizes > 255 bytes.
The driver already supports u16 reply size in all
other places, this was the only missing change.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Align to latest version of the auto generated wmi file
describing the interface with FW
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since the addition of the TXQ stats to cfg80211, the station_info struct
has grown to be quite large, which results in warnings when allocated on
the stack. Fix the affected places to do dynamic allocations instead.
Fixes: 52539ca89f36 ("cfg80211: Expose TXQ stats and parameters to userspace")
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Track the connection status per-VIF.
The data path code is also updated to support multiple VIFs.
This includes RX and TX VRING management, NAPI poll loops,
RX reordering and related code.
Power management code used to check if the main interface
is up or based on connection state of the main interface,
adapt this code to take all VIFs into account.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As more support is added for multiple VIFs, there is a need
to protect the wil6210_vif structure from access while it is
deleted (mainly from del_virtual_intf operation).
Instead of adding another mutex, use p2p_wdev_mutex and rename
it to vif_mutex to reflect the added role. Its existing roles
are similar so it extends nicely (for example it protects the
scan_request member which is also a member of wil6210_vif).
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for multiple VIFs in the cfg80211 operations start_ap,
stop_ap and change_beacon. This change allows starting multiple APs
using virtual interfaces.
The data path and most other operations are still working only
on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add generic support in cfg80211 operations add_virtual_intf
and del_virtual_intf for adding/removing VIFs of any
interface type, and fix change_virtual_intf to allow changing
the interface type of a VIF. Previously these operations
only worked for the P2P_DEVICE interface which is not a real
VIF(it is management-only and shares radio with the main
interface).
Currently the interface combination is validated, the VIF is
added/removed in the firmware and the appropriate net/wireless
device is also added/removed.
Added minimal support for proper interface up/down and module
unload but most operations still work only on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Simple infrastructure changes for supporting multiple
virtual interfaces (multiple VIFs).
It is still not possible to add new VIFs so the only VIF
belongs to the main interface.
Main changes:
1. Add MAC ID(mid) argument to wmi_send and wmi_call to
allow invoking WMI commands on different VIFs.
2. Similarly, in WMI event handler look at the mid reported
by FW and extract VIF structure (currently only for main
interface). All WMI event handlers operate on wil6210_vif
structure so they know on which VIF they were called.
3. Trivial changes to use wil6210_vif structure and MID
throughout the code.
4. Various changes to logging to report MID.
More complete multiple VIFs support will be added gradually
in next patches.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The field preset_chandef of wireless_dev must not be accessed
by the driver because it is private to cfg80211. Store the
monitor channel locally in wil6210_priv instead.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
"FIXME: IRQ mask debug" and "FIXME: interrupts enabled - for debug"
can be removed because wil6210_debug_irq_mask() is now considered
production feature.
"FIXME FW can transmit only ucast frames to peer" and "FIXME real
ring_id instead of hard coded 0" can be removed because FW/HW already
support multicast transmission.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for sched_scan_start/stop by sending PNO commands to FW.
Driver reports max_sched_scan_reqs and invokes
cfg80211_sched_scan_results upon receiving WMI_SCHED_SCAN_RESULT_EVENTID
from FW.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Upon receiving suspend reject, print reject reason.
Upon receiving resume event, print resume triggers.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add a length check in wmi_set_ie to detect unsigned integer
overflow.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When loading FW from file add block size checks to ensure a
corrupted FW file will not cause the driver to write outside
the device memory.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The current length check:
sizeof(cmd) + len > r->entry_size
will allow very large values of len (> U16_MAX - sizeof(cmd))
and can cause a buffer overflow. Fix the check to cover this case.
In addition, ensure the mailbox entry_size is not too small,
since this can also bypass the above check.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
