summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath/ath9k
AgeCommit message (Collapse)AuthorFilesLines
2015-07-11ath9k_hw: fix device ID check for AR956xFelix Fietkau1-0/+1
Because of the missing return, the macVersion value was being overwritten with an invalid register read Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-23Merge tag 'wireless-drivers-next-for-davem-2015-06-18' of ↵David S. Miller5-6/+47
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== Major changes: mwifiex: * enhancements for AP mode: support verbose information in station dump command and also information about AP link. * enable power save by default brcmfmac: * fix module reload issue for PCIe * improving msgbuf protocol for PCIe devices * rework .get_station() cfg80211 callback operation * determine interface combinations upon device feature support ath9k: * ath9k_htc: add support of channel switch wil6210: * add modparam for bcast ring size * support hidden SSID * add per-MCS Rx stats ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-15ath9k_htc: add support of channel switchChun-Yeow Yeoh4-1/+40
Add the support of channel switching functionality, similar to ath9k support. Tested with TP-Link TL-WN722N and TL-WN821N. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-10mac80211: convert HW flags to unsigned long bitmapJohannes Berg2-22/+22
As we're running out of hardware capability flags pretty quickly, convert them to use the regular test_bit() style unsigned long bitmaps. This introduces a number of helper functions/macros to set and to test the bits, along with new debugfs code. The occurrences of an explicit __clear_bit() are intentional, the drivers were never supposed to change their supported bits on the fly. We should investigate changing this to be a per-frame flag. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-06-08ath9k: fix DMA stop sequence for AR9003+Felix Fietkau1-5/+7
AR93xx and newer needs to stop rx before tx to avoid getting the DMA engine or MAC into a stuck state. This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam. Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-26ath9k: split ar5008_hw_spur_mitigate and reuse common code in ↵Oleksij Rempel3-214/+87
ar9002_hw_spur_mitigate. [ar5008 and ar9002]_hw_spur_mitigate have big portion of identical code. This patch will move common part of ar5008_hw_spur_mitigate to ar5008_hw_cmn_spur_mitigate and reuse it in ar9002_hw_spur_mitigate. As noticed by Joe Perches I reuse ar9002_hw_spur_mitigate (const) version of declarations for pilot_mask_reg and chan_mask_reg. There should be no other difference with original code. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-26ath9k_htc: memory corruption calling set_bit()Dan Carpenter1-3/+3
In d8a2c51cdcae ('ath9k_htc: Use atomic operations for op_flags') we changed things like this: - if (priv->op_flags & OP_TSF_RESET) { + if (test_bit(OP_TSF_RESET, &priv->op_flags)) { The problem is that test_bit() takes a bit number and not a mask. It means that when we do: set_bit(OP_TSF_RESET, &priv->op_flags); Then it sets the (1 << 6) bit instead of the 6 bit so we are setting a bit which is past the end of the unsigned long. Fixes: d8a2c51cdcae ('ath9k_htc: Use atomic operations for op_flags') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-24Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of ↵David S. Miller3-133/+644
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== ath10k: * enable channel 144 on 5 GHz * enable Adaptive Noise Immunity (ANI) by default * add Wake on Wireless LAN (WOW) patterns support * add basic Tunneled Direct Link Setup (TDLS) support * add multi-channel support for QCA6174 * enable IBSS RSN support * enable Bluetooth Coexistance whenever firmware supports it * add more versatile way to set bitrates used by the firmware ath9k: * spectral scan: add support for multiple FFT frames per report iwlwifi: * major rework of the scan code (Luca) * some work on the thermal code (Chaya Rachel) * some work on the firwmare debugging infrastructure brcmfmac: * SDIO suspend and resume fixes * wiphy band info and changes in regulatory settings * add support for BCM4324 SDIO and BCM4358 PCIe * enable support of PCIe devices on router platforms (Hante) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-27/+25
Four minor merge conflicts: 1) qca_spi.c renamed the local variable used for the SPI device from spi_device to spi, meanwhile the spi_set_drvdata() call got moved further up in the probe function. 2) Two changes were both adding new members to codel params structure, and thus we had overlapping changes to the initializer function. 3) 'net' was making a fix to sk_release_kernel() which is completely removed in 'net-next'. 4) In net_namespace.c, the rtnl_net_fill() call for GET operations had the command value fixed, meanwhile 'net-next' adjusted the argument signature a bit. This also matches example merge resolutions posted by Stephen Rothwell over the past two days. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-09ath9k: Enable short repeat by default on ath9k_htcNick Kossifidis1-1/+1
Normal FFT reports generate a LOT of data, to save resources enable short repeat by default also on ath9k_htc (it's already enabled by default on ath9k). This can always be changed from userspace if needed. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: Mix the received FFT bins to the random poolNick Kossifidis1-1/+13
E/M noise is a pretty good source of entropy so we mix the FFT measurements of the E/M spectrum to /dev/random pool. Note that this doesn't increase the pool's entropy count but it still helps on improving the output of /dev/(u)random. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: No need for that extra memsetNick Kossifidis1-1/+2
Temp buffer is only used for fixing malformed frames, there is no need to memset it every time. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: Skip FFT reports if we are out of output buffersNick Kossifidis1-0/+28
There is no reason to keep processing FFT reports if there is no space left on the relayfs buffers for the results. This saves lots of CPU cycles, especially on normal (non-short) reports. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: No need for that extra memcpyNick Kossifidis1-4/+2
No need to copy the frame to the temporary buffer when its length is ok. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: Skip malformed frames on normal FFT reportNick Kossifidis1-32/+62
Since we have lots of frames on a normal FFT report don't bother processing the malformed ones. Only try to fix malformed frames in case of a short FFT report (only a single frame on the report). Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: Support processing of multiple FFT frames per report.Nick Kossifidis1-30/+237
Since we can identify the FFT frames on the report by checking the consistency of their magnitude info, we can process all of them, even when some of them are corrupted. This patch introduces two functions to quickly verify the integrity of the mag_info fields and some further tweaks to detect the frames in the report and process them. Note that in case of missing bytes we don't duplicate them, instead we leave them as zeroes. This way we get less noise on the FFT plot. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: Perform integrity checks when processing FFT framesNick Kossifidis1-6/+163
a) Check that the maximum magnitude is at the specified index b) Check if the maximum magnitude index is at dc_pos and if so calculate a new one (value at dc_pos is invalid) c) Check if the specified maximum magnitude is indeed the maximum Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: Move processing of FFT frames to different functionsNick Kossifidis2-111/+171
Since more checks and fixes will be added later and ath_cmn_process_fft is already big enough. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-09ath9k: Fix hanlding of maximum magnitude indexNick Kossifidis2-10/+28
Maximum magnitude index is a 5bit signed integer, convert to an 8bit signed integer and then "shift" it so that it can be used as an array index. Note that the current implementation adds +1 to the index value (so it can't be used as an array index) and it's only valid for HT20 channels. Note that the maximum magnitude index is not being used by the userspace tools that parse FFT samples (they just use maximum magnitude) so this doesn't break userspace compatibility. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-03ath9k: fix per-packet tx power configurationLorenzo Bianconi1-27/+25
Do not use ieee80211_vif pointer in ath_get_rate_txpower() since it has been overwritten by setup_frame_info() and it will result in a corrupted tx power configuration. Set per-packet tx power in setup_frame_info() according to current vif tx power. Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-04-24mac80211: remove support for IFF_PROMISCJohannes Berg4-17/+3
This support is essentially useless as typically networks are encrypted, frames will be filtered by hardware, and rate scaling will be done with the intended recipient in mind. For real monitoring of the network, the monitor mode support should be used instead. Removing it removes a lot of corner cases. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-04-07ath9k: add extra GPIO led supportMiaoqing Pan4-3/+27
ar9550 or later chips, the AR_GPIO_IN_OUT register only can control GPIO[0:3]. For the extra GPIO, use standard GPIO calls instead of WMAC internal registers. Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-04-07ath9k_htc: check seq number instead of cmd id for timeoutFred Chou2-7/+7
As the driver may send multiple wmi commands with identical cmd id, it is more robust to check seq number for timeout instead. Signed-off-by: Fred Chou <fred.chou.nd@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-04-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller3-10/+14
Conflicts: drivers/net/usb/asix_common.c drivers/net/usb/sr9800.c drivers/net/usb/usbnet.c include/linux/usb/usbnet.h net/ipv4/tcp_ipv4.c net/ipv6/tcp_ipv6.c The TCP conflicts were overlapping changes. In 'net' we added a READ_ONCE() to the socket cached RX route read, whilst in 'net-next' Eric Dumazet touched the surrounding code dealing with how mini sockets are handled. With USB, it's a case of the same bug fix first going into net-next and then I cherry picked it back into net. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-30ath9k: use REG_RMW and rmw buffer in ath9k_hw_def_set_gainOleksij Rempel1-20/+14
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: use REG_RMW and rmw buffer in ath9k_hw_4k_set_board_valuesOleksij Rempel1-6/+8
replace REG_WRITE to REG_RMW and place every thing in one RMW buffer. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: use REG_RMW and rmw buffer in ath9k_hw_4k_set_gainOleksij Rempel1-8/+8
it is possible to reduce time needed for this function by rplacing REG_WRITE with REG_RMW (plus dummy 0) and putt all commands in same buffer. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ath9k_hw_4k_set_board_values: use rmw bufferOleksij Rempel1-0/+2
it will reduce exution time from 14ms to 2ms on ar9271 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ath9k_hw_analog_shift_rmw: use REG_RMWOleksij Rempel1-6/+1
use REG_RMW in ath9k_hw_analog_shift_rmw. It will double execution speed on usb bus. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ath9k_hw_4k_set_board_values: use rmw bufferOleksij Rempel1-0/+2
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: use rmw buffer in ath9k_hw_set_operating_mode and ath9k_hw_resetOleksij Rempel1-0/+4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ath9k_hw_set_4k_power_cal_tabl: use rmw bufferOleksij Rempel1-0/+2
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: write buffer related optimisation in ar5008_hw_set_channel_regsOleksij Rempel1-2/+3
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ath9k_hw_loadnf: use REG_RMWOleksij Rempel1-11/+8
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: use one shot read in ath9k_hw_update_mibstatsOleksij Rempel1-5/+15
this will reduce some overhead on usb bus. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ar9271_hw_pa_cal: use REG_READ_ARRAYOleksij Rempel1-2/+1
insted of reading each register separatly and waste 4ms on each operation, we can use one shot read. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: add new function ath9k_hw_read_arrayOleksij Rempel2-0/+33
REG_READ generate most overhead on usb bus. It send and read micro packages and reduce usb bandwidth. To reduce this overhead we should read in batches. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: add multi_read to be compatible with ath9k_htcOleksij Rempel1-0/+11
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ar9271_hw_pa_cal: use RMW bufferOleksij Rempel1-2/+6
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ar9271_hw_pa_cal: use proper makroses.Oleksij Rempel1-24/+19
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k: ar9271_hw_pa_cal - use defs instead of magin numbersOleksij Rempel1-17/+18
This function uses mixed styles for register names/numbers which is make harder reading and optimisation. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-30ath9k_htc: add new WMI_REG_RMW_CMDID commandOleksij Rempel5-6/+172
Since usb bus add extra delay on each request, a command with read + write requests is too expensive. We can dramtically reduce usb load by moving this command to firmware. In my tests, this patch will reduce channel scan time for about 5-10 seconds. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-21ath9k: Fix AIC compilation errorSujith Manoharan1-2/+4
AIC needs to be registered only when BTCOEX is enabled. This fixes the error reported by kbuild: >> ERROR: "ar9003_hw_attach_aic_ops" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined! Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-20ath9k: Start AIC calibration during MCI resetSujith Manoharan1-0/+3
When a MCI reset is done, make sure that AIC is started. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-20ath9k: Handle MCI_STATE_AIC_CALSujith Manoharan3-2/+31
Add the main AIC calibration function to handle MCI_STATE_AIC_CAL. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-20ath9k: Handle MCI_STATE_AIC_STARTSujith Manoharan3-0/+38
This patch adds a function to handle the MCI message MCI_STATE_AIC_START. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-20ath9k: Handle MCI_STATE_AIC_CAL_RESETSujith Manoharan3-0/+13
Add a routine to handle the MCI_STATE_AIC_CAL_RESET message. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-20ath9k: Disable AIC by defaultSujith Manoharan2-1/+8
Since various MCI messages need to be handled, along with driver-level support in upper layers, disable AIC for now. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-20ath9k: Process the AIC calibration resultsSujith Manoharan1-0/+245
This patch adds support for post-processing the AIC calibration results. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-20ath9k: Finish AIC calibrationSujith Manoharan1-1/+77
Set the appropriate bits in the HW after AIC calibration is done. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-25 05:13:12 +0000