| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
ar9550 or later chips, the AR_GPIO_IN_OUT register only can
control GPIO[0:3]. For the extra GPIO, use standard GPIO calls
instead of WMAC internal registers.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
REG_READ generate most overhead on usb bus. It send and read micro packages
and reduce usb bandwidth. To reduce this overhead we should read in batches.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
TPC support has been observed to cause some tx power fluctuations on
some devices with at least AR934x and AR938x chips.
Disable it for now until the bugs have been found and fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Cards based on AR9462/AR9565 support more PCIE
power save mechanisms, so register them correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since the number of patterns that can be configured in
the HW is higher for newer chips, store the chip-specific
value in ath9k_hw_wow.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enabling WOW based on the chip is incorrect since
it needs to be done for specific sub-devices which
have proper platform support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable per-packet TPC on AR9002 based chips by default
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable hw TPC by default on AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.
The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.
Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.
So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.
This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n
and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.
Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Based on OpenWrt patch by Gabor Juhos
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some devices have multiple bands enables in the EEPROM data, even though
they are only calibrated for one. Allow platform data to disable
unsupported bands.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This makes the initial NF calibration less likely to fail.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On AR934x and newer SoC devices, the layout of the AR_RTC_PLL_CONTROL
register changed. This currently breaks at least 5/10 MHz operation.
AR933x uses the old layout.
It might also have been causing other stability issues because of the
different location of the PLL_BYPASS bit which needs to be set during
PLL clock initialization.
This patch also removes more instances of hardcoded register values in
favor of properly computed ones with the PLL_BYPASS bit added.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On AR934x rev 3, settin the ad-hoc flag completely messes up hardware
state - beacons get stuck, almost no packets make it out, hardware is
constantly reset.
When leaving out that flag and setting up the hw like in AP mode, TSF
timers won't be automatically synced, but at least the rest works.
AR934x rev 2 and older are not affected by this bug
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It is needed for AR934x as well
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Enable pulse detection on extension channel if 40MHz channel width has been set
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Do not overwrite ACK timeout estimation in ath9k_hw_init_global_settings() if
dynack processing has been enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add dynamic ACK timeout estimation algorithm based on ACK frame RX timestamp,
TX frame timestamp and frame duration.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Tested-by: Philippe Duchein <wireless-dev@duchein.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove static keyword and export ath9k_hw_setslottime(),
ath9k_hw_set_ack_timeout() and ath9k_hw_set_cts_timeout() in hw.h.
These methods will be used in ACK timeout estimation algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move ath9k_hw_set_radar_params() in ath9k_hw_reset() in order to avoid
AR_PHY_RADAR registers are overwritten after hw reset
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
|
|
We have interfaces. Remove the open coded cruft. Reduces text size
along with the code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Save TSF in channel context for multiple operating channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
to fix compile errors
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The SREV register in the WMAC register space does not contain the chip
revision, so it needs to be passed in from the kernel.
With an updated kernel, this fixes tx gain table selection.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit "ath9k: reduce baseband hang detection false positive rate"
added a delay in the loop checking the baseband state, however it was
unreachable due to previous 'continue' statements.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
|
|
Check if the baseband state remains stable, and add a small delay
between register reads.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
There is no benefit in retaining the legacy rate control module
in the driver codebase.
It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.
This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.
The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use mdelay instead of udelay to fix this error:
ERROR: "__bad_udelay" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR9100 requires a larger delay after waking up
the RTC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
