| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc876 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f56 ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes checkpatch warnings:
Prefer 'unsigned long' over 'unsigned long int' as the int is unnecessary
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds the tx statistics pkts/bytes dump
in rate table format.
Dump format table is similar to http://mcsindex.com/
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
command:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch helps to get the power save state change of each peer
connected to the AP. With WMI_10_4_PEER_STA_PS_STATECHG_EVENTID
event, ps state of each peer is reported to user space via
debugfs.
Use the below command to get the ps state of each sta:
cat /sys/kernel/debug/ieee80211/phyX/netdev::wlanX/stations/
XX:XX:XX:XX:XX:XX/peer_ps_state
If STA is in power save state, we get the peer_ps_state value as 1.
if STA is not in power save state, we get the peer_ps_state value as 0.
If ps_state event is disabled, we get the peer_ps_state value as 2.
We can enable/disable the ps_state events using the debugfs flag
"ps_state_enable"
echo Y > /sys/kernel/debug/ieee80211/phyX/ath10k/ps_state_enable
Y = 1 to enable and Y = 0 to disable
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds 'tx_stats' in per station debugfs entry.
Use this command to dump tx_stats:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
During write to some of debugfs in ath10k, few variables exposing stack
data when process user input. which leads to possible information leak.
This patch fix this issue by initializing buffer and checks
the return valure of 'simple_write_to_buffer'.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Added per tid sta counters for the following
- Total number MSDUs received from firmware
- Number of MSDUs received with errors like decryption, crc, mic ,etc.
- Number of MSDUs dropped in the driver
- A-MPDU/A-MSDU subframe stats
- Number of MSDUS passed to mac80211
All stats other than A-MPDU stats are only for received data frames.
A-MPDU stats might have stats for management frames when monitor
interface is active where management frames are notified both in wmi
and HTT interfaces.
These per tid stats can be enabled with tid bitmask through a debugfs
like below
echo <tid_bitmask> > /sys/kernel/debug/ieee80211/phyX/ath10k/sta_tid_stats_mask
tid 16 (tid_bitmask 0x10000) is used for non-qos data/management frames
The stats are read from
/sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/<sta_mac>/dump_tid_stats
Sample output:
To enable rx stats for tid 0, 5 and 6,
echo 0x00000061 > /sys/kernel/debug/ieee80211/phy0/ath10k/sta_tid_stats_mask
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan15/stations/8c\:fd\:f0\:0a\:8e\:df/dump_tid_stats
Driver Rx pkt stats per tid, ([tid] count)
------------------------------------------
MSDUs from FW [00] 2567 [05] 3178 [06] 1089
MSDUs unchained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:chained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:filtered [00] 0 [05] 0 [06] 0
MSDUs queued for mac80211 [00] 2567 [05] 3178 [06] 1089
MSDUs with error:fcs_err [00] 0 [05] 0 [06] 2
MSDUs with error:tkip_err [00] 0 [05] 0 [06] 0
MSDUs with error:crypt_err [00] 0 [05] 0 [06] 0
MSDUs with error:peer_idx_inval [00] 0 [05] 0 [06] 0
A-MPDU num subframes upto 10 [00] 2567 [05] 3178 [06] 1087
A-MPDU num subframes 11-20 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 21-30 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 31-40 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 41-50 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 51-60 [00] 0 [05] 0 [06] 0
A-MPDU num subframes >60 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 1 [00] 2567 [05] 3178 [06] 1089
A-MSDU num subframes 2 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 3 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 4 [00] 0 [05] 0 [06] 0
A-MSDU num subframes >4 [00] 0 [05] 0 [06] 0
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Update year for Qualcomm Atheros, Inc. copyrights.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Remove CONFIG_MAC80211_DEBUGFS dependency on ath10k_sta_statistics().
ath10k_sta_statistics() has per sta tx/rx stats and this should not
be dependent on MAC80211_DEBUGFS.
No changes in functionality.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Fix output from checkpatch.pl like:
Symbolic permissions 'S_IRUSR' are not preferred.
Consider using octal permissions '0400'.
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Per STA tx bitrate info is filled from peer stats.
Export per sta txrate info to cfg80211/nl80211
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
cfg80211/nl80211 interface changes for per STA total rx-duration and
very basic 'ath10k_sta_statistics' mac80211 callback is implemented
to extend support for per station statistics from the driver.
Also provision in 'iw dev wlan#N station dump' to parse rx-duration
is supported. So its safer to remove the debugfs entry for per STA
rx-duration
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211
This can also act as a placeholder for any new per STA stats support
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled
The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats
{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}
Fixes: f9575793d44c ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add debugfs support for per client total rx duration, track this
via the report of Peer stats rx duration reported for every 500ms
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This per-station debugfs entry helps to send delba in manual mode
for debugging purpose. It accepts tid, initiator and reason code
as inputs.
To send delba,
echo 0 1 37 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This per-station debugfs entry helps to send addba response in
manual mode for debugging purpose. It accepts tid and status code
as input arguments.
To send addba response,
echo 0 25 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba_resp
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This per-station debugfs entry helps to send addba request in manual
mode. Need to pass two configuration parameters (tid, buffer size)
as input.
To send addba,
echo 1 32 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add per station debugfs files when a station is added to mac80211's
station list. This helps to group peer specific debugfs entries
altogether. Right now this callback adds support to test aggregation
procedures (addba/addba_resp/delba) manually.
To enable automatic aggregation in target,
echo 0 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
