| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update all open-coded tests for all 4 PHY_INTERFACE_MODE_RGMII* values
to use the newly introduced helper: phy_interface_is_rgmii.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.
Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If registering of one of them fails, all already registered drivers
of this module will be unregistered.
Use the new register/unregister functions in all drivers
registering more than one driver.
amd.c, realtek.c: Simplify: directly return registration result.
Tested with broadcom.c
All others compile-tested.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the interrupt mask for IC101 A/G devices
and now enables the link/speed/duplex interrupts.
This is done by setting the "INTR pin used" bit and cleaning
all the other bits in the Register 17.
Reported-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.
This patch also fixes the return value of ip101a_config_init.
Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.
The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The extra delay of 2ns to adjust RX clock phase is actually needed
in RGMII mode. Tested on the HDK7108 (STx7108c2).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Usually you have to take the bus lock. Why not here too?
I saw this when working on something else. Not even compile tested.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Cc: "Uwe Kleine-Konig" <u.kleine-koenig@pengutronix.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the IC+ IP101A Single port 10/100 PHY
and supports the APS (i.e. power saving mode while link is down)
for both IP1001 and IP101A (where this mode is supported).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compile tested.
remove unnecessary code that matches this coccinelle pattern
if (...)
return ret;
return ret;
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
|
|
This patch adds the IC+ IP1001 (Gigabit Ethernet Transceiver) driver.
I've had to add an additional delay (2ns) to adjust RX clock phase at
GMII/ RGMII interface (according to the PHY data-sheet). This helps to
have the RGMII working on some ST platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MODULE_DEVICE_TABLE only expands to something if it's compiled
for a module. So when building-in support for the phys, the
mdio_device_id tables are unused. Marking them with __maybe_unused
fixes the following warnings:
drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used
drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used
drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used
drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used
drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used
drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used
drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used
drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used
drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used
drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used
drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used
drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used
drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used
drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used
drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/stmmac/stmmac_main.c
drivers/net/wireless/wl12xx/wl1271_cmd.c
drivers/net/wireless/wl12xx/wl1271_main.c
drivers/net/wireless/wl12xx/wl1271_spi.c
net/core/ethtool.c
net/mac80211/scan.c
|
|
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
The ICPlus IP175C sports a 100Mbit/s 4-port switch in addition
to a dedicated 100Mbit/s WAN port.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
