| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-06-08
Michal prevents setting of VF VLAN capabilities in switchdev mode and
removes, not needed, specific switchdev VLAN operations.
Karol converts u16 variables to unsigned int for GNSS calculations.
Christophe Jaillet corrects the parameter order for a couple of
devm_kcalloc() calls.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Use correct order for the parameters of devm_kcalloc()
ice: remove u16 arithmetic in ice_gnss
ice: remove VLAN representor specific ops
ice: don't set VF VLAN caps in switchdev
====================
Link: https://lore.kernel.org/r/20220608160757.2395729-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-06-08
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2022-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: fs, fail conflicting actions
net/mlx5: Rearm the FW tracer after each tracer event
net/mlx5: E-Switch, pair only capable devices
net/mlx5e: CT: Fix cleanup of CT before cleanup of TC ct rules
Revert "net/mlx5e: Allow relaxed ordering over VFs"
MAINTAINERS: adjust MELLANOX ETHERNET INNOVA DRIVERS to TLS support removal
====================
Link: https://lore.kernel.org/r/20220608185855.19818-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Swap around the GRE and VLAN parts in the flow-key offloaded by
the driver to fit in with other tunnel types and the firmware.
Without this change used cases with GRE+VLAN on the outer header
does not get offloaded as the flow-key mismatches what the
firmware expect.
Fixes: 0d630f58989a ("nfp: flower: add support to offload QinQ match")
Fixes: 5a2b93041646 ("nfp: flower-ct: compile match sections of flow_payload")
Signed-off-by: Etienne van der Linde <etienne.vanderlinde@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nfp_net_sriov_check is added in nfp_app_get_vf_config which intends
to ensure ivi->vlan_proto and ivi->max_tx_rate/min_tx_rate can be
read from VF config table only when firmware supports corresponding
capability.
However, "nfp_app_get_vf_config" can be called by commands like
"ip a", "ip link set $DEV up" and "ip link set $DEV vf $NUM vlan
$param" (with VF). When using commands above, many warnings
"ndo_set_vf_<cap_x> not supported" would appear if firmware doesn't
support VF rate limit and 802.1ad VLAN assingment. If more VFs are
created, things could get worse.
Thus, this patch add an extra bool parameter for nfp_net_sriov_check
to enable/disable the cap check warning report. Unnecessary warnings
in nfp_app_get_vf_config can be avoided. Valid warnings in kinds of
vf setting function can be reserved.
Fixes: e0d0e1fdf1ed ("nfp: VF rate limit support")
Fixes: 59359597b010 ("nfp: support 802.1ad VLAN assingment to VF")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- eth: amt: fix possible null-ptr-deref in amt_rcv()
Previous releases - regressions:
- tcp: use alloc_large_system_hash() to allocate table_perturb
- af_unix: fix a data-race in unix_dgram_peer_wake_me()
- nfc: st21nfca: fix memory leaks in EVT_TRANSACTION handling
- eth: ixgbe: fix unexpected VLAN rx in promisc mode on VF
Previous releases - always broken:
- ipv6: fix signed integer overflow in __ip6_append_data
- netfilter:
- nat: really support inet nat without l3 address
- nf_tables: memleak flow rule from commit path
- bpf: fix calling global functions from BPF_PROG_TYPE_EXT programs
- openvswitch: fix misuse of the cached connection on tuple changes
- nfc: nfcmrvl: fix memory leak in nfcmrvl_play_deferred
- eth: altera: fix refcount leak in altera_tse_mdio_create
Misc:
- add Quentin Monnet to bpftool maintainers"
* tag 'net-5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
net: amd-xgbe: fix clang -Wformat warning
tcp: use alloc_large_system_hash() to allocate table_perturb
net: dsa: realtek: rtl8365mb: fix GMII caps for ports with internal PHY
net: dsa: mv88e6xxx: correctly report serdes link failure
net: dsa: mv88e6xxx: fix BMSR error to be consistent with others
net: dsa: mv88e6xxx: use BMSR_ANEGCOMPLETE bit for filling an_complete
net: altera: Fix refcount leak in altera_tse_mdio_create
net: openvswitch: fix misuse of the cached connection on tuple changes
net: ethernet: mtk_eth_soc: fix misuse of mem alloc interface netdev[napi]_alloc_frag
ip_gre: test csum_start instead of transport header
au1000_eth: stop using virt_to_bus()
ipv6: Fix signed integer overflow in l2tp_ip6_sendmsg
ipv6: Fix signed integer overflow in __ip6_append_data
nfc: nfcmrvl: Fix memory leak in nfcmrvl_play_deferred
nfc: st21nfca: fix incorrect sizing calculations in EVT_TRANSACTION
nfc: st21nfca: fix memory leaks in EVT_TRANSACTION handling
nfc: st21nfca: fix incorrect validating logic in EVT_TRANSACTION
net: ipv6: unexport __init-annotated seg6_hmac_init()
net: xfrm: unexport __init-annotated xfrm4_protocol_init()
net: mdio: unexport __init-annotated mdio_bus_init()
...
|
|
gcc-12 started warning about 'tracker' being used uninitialized:
drivers/net/ethernet/mellanox/mlx5/core/lag/lag.c: In function ‘mlx5_do_bond’:
drivers/net/ethernet/mellanox/mlx5/core/lag/lag.c:786:28: warning: ‘tracker’ is used uninitialized [-Wuninitialized]
786 | struct lag_tracker tracker;
| ^~~~~~~
which seems to be because it doesn't track how the use (and
initialization) is bound by the 'do_bond' flag.
But admittedly that 'do_bond' usage is fairly complicated, and involves
passing it around as an argument to helper functions, so it's somewhat
understandable that gcc doesn't see how that all works.
This function could be rewritten to make the use of that tracker
variable more obviously safe, but for now I'm just adding the forced
initialization of it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gem_ptp_set_one_step_sync() always returns zero thus change its return
type to void.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220608080818.1495044-1-claudiu.beznea@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
see warning:
| drivers/net/ethernet/amd/xgbe/xgbe-drv.c:2787:43: warning: format specifies
| type 'unsigned short' but the argument has type 'int' [-Wformat]
| netdev_dbg(netdev, "Protocol: %#06hx\n", ntohs(eth->h_proto));
| ~~~~~~ ^~~~~~~~~~~~~~~~~~~
Variadic functions (printf-like) undergo default argument promotion.
Documentation/core-api/printk-formats.rst specifically recommends
using the promoted-to-type's format flag.
Also, as per C11 6.3.1.1:
(https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf)
`If an int can represent all values of the original type ..., the
value is converted to an int; otherwise, it is converted to an
unsigned int. These are called the integer promotions.`
Since the argument is a u16 it will get promoted to an int and thus it is
most accurate to use the %x format specifier here. It should be noted that the
`#06` formatting sugar does not alter the promotion rules.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Justin Stitt <jstitt007@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20220607191119.20686-1-jstitt007@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-07
This series contains updates to ixgbe driver only.
Olivier Matz resolves an issue so that broadcast packets can still be
received when VF removes promiscuous settings and removes setting of
VLAN promiscuous, in promiscuous mode, to prevent a loop when VFs are
bridged.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ixgbe: fix unexpected VLAN Rx in promisc mode on VF
ixgbe: fix bcast packets Rx on VF after promisc removal
====================
Link: https://lore.kernel.org/r/20220607181538.748786-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2022-06-07
This series contains updates to i40e and iavf drivers.
Mateusz adds implementation for setting VF VLAN pruning to allow user to
specify visibility of VLAN tagged traffic to VFs for i40e. He also adds
waiting for result from PF for setting MAC address in iavf.
====================
Link: https://lore.kernel.org/r/20220607175506.696671-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Every iteration of for_each_child_of_node() decrements
the reference count of the previous node.
When break from a for_each_child_of_node() loop,
we need to explicitly call of_node_put() on the child node when
not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: bbd2190ce96d ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220607041144.7553-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netdev[napi]_alloc_frag
When rx_flag == MTK_RX_FLAGS_HWLRO,
rx_data_len = MTK_MAX_LRO_RX_LENGTH(4096 * 3) > PAGE_SIZE.
netdev_alloc_frag is for alloction of page fragment only.
Reference to other drivers and Documentation/vm/page_frags.rst
Branch to use __get_free_pages when ring->frag_size > PAGE_SIZE.
Signed-off-by: Chen Lin <chen45464546@163.com>
Link: https://lore.kernel.org/r/1654692413-2598-1-git-send-email-chen45464546@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When combining two steering rules into one check
not only do they share the same actions but those
actions are also the same. This resolves an issue where
when creating two different rules with the same match
the actions are overwritten and one of the rules is deleted
a FW syndrome can be seen in dmesg.
mlx5_core 0000:03:00.0: mlx5_cmd_check:819:(pid 2105): DEALLOC_MODIFY_HEADER_CONTEXT(0x941) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1ab444)
Fixes: 0d235c3fabb7 ("net/mlx5: Add hash table to search FTEs in a flow-group")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The current design does not arm the tracer if traces are available before
the tracer string database is fully loaded, leading to an unfunctional tracer.
This fix will rearm the tracer every time the FW triggers tracer event
regardless of the tracer strings database status.
Fixes: c71ad41ccb0c ("net/mlx5: FW tracer, events handling")
Signed-off-by: Feras Daoud <ferasda@nvidia.com>
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
OFFLOADS paring using devcom is possible only on devices
that support LAG. Filter based on lag capabilities.
This fixes an issue where mlx5_get_next_phys_dev() was
called without holding the interface lock.
This issue was found when commit
bc4c2f2e0179 ("net/mlx5: Lag, filter non compatible devices")
added an assert that verifies the interface lock is held.
WARNING: CPU: 9 PID: 1706 at drivers/net/ethernet/mellanox/mlx5/core/dev.c:642 mlx5_get_next_phys_dev+0xd2/0x100 [mlx5_core]
Modules linked in: mlx5_vdpa vringh vhost_iotlb vdpa mlx5_ib mlx5_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_umad ib_ipoib ib_cm ib_uverbs ib_core overlay fuse [last unloaded: mlx5_core]
CPU: 9 PID: 1706 Comm: devlink Not tainted 5.18.0-rc7+ #11
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5_get_next_phys_dev+0xd2/0x100 [mlx5_core]
Code: 02 00 75 48 48 8b 85 80 04 00 00 5d c3 31 c0 5d c3 be ff ff ff ff 48 c7 c7 08 41 5b a0 e8 36 87 28 e3 85 c0 0f 85 6f ff ff ff <0f> 0b e9 68 ff ff ff 48 c7 c7 0c 91 cc 84 e8 cb 36 6f e1 e9 4d ff
RSP: 0018:ffff88811bf47458 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff88811b398000 RCX: 0000000000000001
RDX: 0000000080000000 RSI: ffffffffa05b4108 RDI: ffff88812daaaa78
RBP: ffff88812d050380 R08: 0000000000000001 R09: ffff88811d6b3437
R10: 0000000000000001 R11: 00000000fddd3581 R12: ffff88815238c000
R13: ffff88812d050380 R14: ffff8881018aa7e0 R15: ffff88811d6b3428
FS: 00007fc82e18ae80(0000) GS:ffff88842e080000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f9630d1b421 CR3: 0000000149802004 CR4: 0000000000370ea0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
mlx5_esw_offloads_devcom_event+0x99/0x3b0 [mlx5_core]
mlx5_devcom_send_event+0x167/0x1d0 [mlx5_core]
esw_offloads_enable+0x1153/0x1500 [mlx5_core]
? mlx5_esw_offloads_controller_valid+0x170/0x170 [mlx5_core]
? wait_for_completion_io_timeout+0x20/0x20
? mlx5_rescan_drivers_locked+0x318/0x810 [mlx5_core]
mlx5_eswitch_enable_locked+0x586/0xc50 [mlx5_core]
? mlx5_eswitch_disable_pf_vf_vports+0x1d0/0x1d0 [mlx5_core]
? mlx5_esw_try_lock+0x1b/0xb0 [mlx5_core]
? mlx5_eswitch_enable+0x270/0x270 [mlx5_core]
? __debugfs_create_file+0x260/0x3e0
mlx5_devlink_eswitch_mode_set+0x27e/0x870 [mlx5_core]
? mutex_lock_io_nested+0x12c0/0x12c0
? esw_offloads_disable+0x250/0x250 [mlx5_core]
? devlink_nl_cmd_trap_get_dumpit+0x470/0x470
? rcu_read_lock_sched_held+0x3f/0x70
devlink_nl_cmd_eswitch_set_doit+0x217/0x620
Fixes: dd3fddb82780 ("net/mlx5: E-Switch, handle devcom events only for ports on the same device")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
CT cleanup assumes that all tc rules were deleted first, and so
is free to delete the CT shared resources (e.g the dr_action
fwd_action which is shared for all tuples). But currently for
uplink, this is happens in reverse, causing the below trace.
CT cleanup is called from:
mlx5e_cleanup_rep_tx()->mlx5e_cleanup_uplink_rep_tx()->
mlx5e_rep_tc_cleanup()->mlx5e_tc_esw_cleanup()->
mlx5_tc_ct_clean()
Only afterwards, tc cleanup is called from:
mlx5e_cleanup_rep_tx()->mlx5e_tc_ht_cleanup()
which would have deleted all the tc ct rules, and so delete
all the offloaded tuples.
Fix this reversing the order of init and on cleanup, which
will result in tc cleanup then ct cleanup.
[ 9443.593347] WARNING: CPU: 2 PID: 206774 at drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c:1882 mlx5dr_action_destroy+0x188/0x1a0 [mlx5_core]
[ 9443.593349] Modules linked in: act_ct nf_flow_table rdma_ucm(O) rdma_cm(O) iw_cm(O) ib_ipoib(O) ib_cm(O) ib_umad(O) mlx5_core(O-) mlxfw(O) mlxdevm(O) auxiliary(O) ib_uverbs(O) psample ib_core(O) mlx_compat(O) ip_gre gre ip_tunnel act_vlan bonding geneve esp6_offload esp6 esp4_offload esp4 act_tunnel_key vxlan ip6_udp_tunnel udp_tunnel act_mirred act_skbedit act_gact cls_flower sch_ingress nfnetlink_cttimeout nfnetlink xfrm_user xfrm_algo 8021q garp stp ipmi_devintf mrp ipmi_msghandler llc openvswitch nsh nf_conncount nf_nat mst_pciconf(O) dm_multipath sbsa_gwdt uio_pdrv_genirq uio mlxbf_pmc mlxbf_pka mlx_trio mlx_bootctl(O) bluefield_edac sch_fq_codel ip_tables ipv6 crc_ccitt btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor xor_neon raid6_pq raid1 raid0 crct10dif_ce i2c_mlxbf gpio_mlxbf2 mlxbf_gige aes_neon_bs aes_neon_blk [last unloaded: mlx5_ib]
[ 9443.593419] CPU: 2 PID: 206774 Comm: modprobe Tainted: G O 5.4.0-1023.24.gc14613d-bluefield #1
[ 9443.593422] Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS BlueField:143ebaf Jan 11 2022
[ 9443.593424] pstate: 20000005 (nzCv daif -PAN -UAO)
[ 9443.593489] pc : mlx5dr_action_destroy+0x188/0x1a0 [mlx5_core]
[ 9443.593545] lr : mlx5_ct_fs_smfs_destroy+0x24/0x30 [mlx5_core]
[ 9443.593546] sp : ffff8000135dbab0
[ 9443.593548] x29: ffff8000135dbab0 x28: ffff0003a6ab8e80
[ 9443.593550] x27: 0000000000000000 x26: ffff0003e07d7000
[ 9443.593552] x25: ffff800009609de0 x24: ffff000397fb2120
[ 9443.593554] x23: ffff0003975c0000 x22: 0000000000000000
[ 9443.593556] x21: ffff0003975f08c0 x20: ffff800009609de0
[ 9443.593558] x19: ffff0003c8a13380 x18: 0000000000000014
[ 9443.593560] x17: 0000000067f5f125 x16: 000000006529c620
[ 9443.593561] x15: 000000000000000b x14: 0000000000000000
[ 9443.593563] x13: 0000000000000002 x12: 0000000000000001
[ 9443.593565] x11: ffff800011108868 x10: 0000000000000000
[ 9443.593567] x9 : 0000000000000000 x8 : ffff8000117fb270
[ 9443.593569] x7 : ffff0003ebc01288 x6 : 0000000000000000
[ 9443.593571] x5 : ffff800009591ab8 x4 : fffffe000f6d9a20
[ 9443.593572] x3 : 0000000080040001 x2 : fffffe000f6d9a20
[ 9443.593574] x1 : ffff8000095901d8 x0 : 0000000000000025
[ 9443.593577] Call trace:
[ 9443.593634] mlx5dr_action_destroy+0x188/0x1a0 [mlx5_core]
[ 9443.593688] mlx5_ct_fs_smfs_destroy+0x24/0x30 [mlx5_core]
[ 9443.593743] mlx5_tc_ct_clean+0x34/0xa8 [mlx5_core]
[ 9443.593797] mlx5e_tc_esw_cleanup+0x58/0x88 [mlx5_core]
[ 9443.593851] mlx5e_rep_tc_cleanup+0x24/0x30 [mlx5_core]
[ 9443.593905] mlx5e_cleanup_rep_tx+0x6c/0x78 [mlx5_core]
[ 9443.593959] mlx5e_detach_netdev+0x74/0x98 [mlx5_core]
[ 9443.594013] mlx5e_netdev_change_profile+0x70/0x180 [mlx5_core]
[ 9443.594067] mlx5e_netdev_attach_nic_profile+0x34/0x40 [mlx5_core]
[ 9443.594122] mlx5e_vport_rep_unload+0x15c/0x1a8 [mlx5_core]
[ 9443.594177] mlx5_eswitch_unregister_vport_reps+0x228/0x298 [mlx5_core]
[ 9443.594231] mlx5e_rep_remove+0x2c/0x38 [mlx5_core]
[ 9443.594236] auxiliary_bus_remove+0x30/0x50 [auxiliary]
[ 9443.594246] device_release_driver_internal+0x108/0x1d0
[ 9443.594248] driver_detach+0x5c/0xe8
[ 9443.594250] bus_remove_driver+0x64/0xd8
[ 9443.594253] driver_unregister+0x38/0x60
[ 9443.594255] auxiliary_driver_unregister+0x24/0x38 [auxiliary]
[ 9443.594311] mlx5e_rep_cleanup+0x20/0x38 [mlx5_core]
[ 9443.594365] mlx5e_cleanup+0x18/0x30 [mlx5_core]
[ 9443.594419] cleanup+0xc/0x20cc [mlx5_core]
[ 9443.594424] __arm64_sys_delete_module+0x154/0x2b0
[ 9443.594429] el0_svc_common.constprop.0+0xf4/0x200
[ 9443.594432] el0_svc_handler+0x38/0xa8
[ 9443.594435] el0_svc+0x10/0x26c
Fixes: d1a3138f7913 ("net/mlx5e: TC, Move flow hashtable to be per rep")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
FW is not ready, fix was sent too soon.
This reverts commit f05ec8d9d0d62367b6e1f2cb50d7d2a45e7747cf.
Fixes: f05ec8d9d0d6 ("net/mlx5e: Allow relaxed ordering over VFs")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The conversion to the dma-mapping API in linux-2.6.11 was incomplete
and left a virt_to_bus() call around. There have been a number of
fixes for DMA mapping API abuse in this driver, but this one always
slipped through.
Change it to just use the existing dma_addr_t pointer, and make it
use the correct types throughout the driver to make it easier to
understand the virtual vs dma address spaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Link: https://lore.kernel.org/r/20220607090206.19830-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Remove kernel.h when it is not needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220607125103.487801-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We should have 'n', then 'size', not the opposite.
This is harmless because the 2 values are just multiplied, but having
the correct order silence a (unpublished yet) smatch warning.
While at it use '*tun_seg' instead '*seg'. The both variable have the same
type, so the result is the same, but it lokks more logical.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Change u16 to unsigned int where arithmetic occurs.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In switchdev mode VF VLAN caps will not be set there is no need
to have specific VLAN ops for representor that only returns not
supported error.
As VLAN configuration commands will be blocked, the VF driver
can't disable VLAN stripping at initialization. It leads to the
situation when VLAN stripping on VF VSI is on, but in kernel it
is off. To prevent this, disable VLAN stripping in VSI
initialization. It doesn't break other usecases, because it is set
according to kernel settings.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In switchdev mode any VLAN manipulation from VF side isn't allowed.
In order to prevent parsing VLAN commands don't set VF VLAN caps.
This will result in removing VLAN specific opcodes from allowlist.
If VF send any VLAN specific opcode PF driver will answer with not
supported error.
With this approach VF driver know that VLAN caps aren't supported so it
shouldn't send VLAN specific opcodes. Thanks to that, some ugly errors
will not show up in dmesg (ex. on creating VFs in switchdev mode
there are errors about not supported VLAN insertion and stripping)
Move setting VLAN caps to separate function, including
switchdev mode specific code.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Enable rx checksum offload for mt7986 chipset.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c8699805c18f7fd38315fcb8da2787676d83a32c.1654544585.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ioctl EEPROM query wrongly returns success on read failures, fix
that by returning the appropriate error code.
Fixes: 7202da8b7f71 ("ethtool, net/mlx4_en: Cable info, get_module_info/eeprom ethtool support")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220606115718.14233-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the promiscuous mode is enabled on a VF, the IXGBE_VMOLR_VPE
bit (VLAN Promiscuous Enable) is set. This means that the VF will
receive packets whose VLAN is not the same than the VLAN of the VF.
For instance, in this situation:
┌────────┐ ┌────────┐ ┌────────┐
│ │ │ │ │ │
│ │ │ │ │ │
│ VF0├────┤VF1 VF2├────┤VF3 │
│ │ │ │ │ │
└────────┘ └────────┘ └────────┘
VM1 VM2 VM3
vf 0: vlan 1000
vf 1: vlan 1000
vf 2: vlan 1001
vf 3: vlan 1001
If we tcpdump on VF3, we see all the packets, even those transmitted
on vlan 1000.
This behavior prevents to bridge VF1 and VF2 in VM2, because it will
create a loop: packets transmitted on VF1 will be received by VF2 and
vice-versa, and bridged again through the software bridge.
This patch remove the activation of VLAN Promiscuous when a VF enables
the promiscuous mode. However, the IXGBE_VMOLR_UPE bit (Unicast
Promiscuous) is kept, so that a VF receives all packets that has the
same VLAN, whatever the destination MAC address.
Fixes: 8443c1a4b192 ("ixgbe, ixgbevf: Add new mbox API xcast mode")
Cc: stable@vger.kernel.org
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After a VF requested to remove the promiscuous flag on an interface, the
broadcast packets are not received anymore. This breaks some protocols
like ARP.
In ixgbe_update_vf_xcast_mode(), we should keep the IXGBE_VMOLR_BAM
bit (Broadcast Accept) on promiscuous removal.
This flag is already set by default in ixgbe_set_vmolr() on VF reset.
Fixes: 8443c1a4b192 ("ixgbe, ixgbevf: Add new mbox API xcast mode")
Cc: stable@vger.kernel.org
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Make iavf_set_mac synchronous by waiting for a response
from a PF. Without this iavf_set_mac is always returning
success even though set_mac can be rejected by a PF.
This ensures that when set_mac exits netdev MAC is updated.
This is needed for sending ARPs with correct MAC after
changing VF's MAC. This is also needed by bonding module.
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
VFs by default are able to see all tagged traffic regardless of trust
and VLAN filters configured.
Add new private flag vf-vlan-pruning that allows changing of default
VF behavior for tagged traffic. When the flag is turned on
untrusted VF will only be able to receive untagged traffic
or traffic with VLAN tags it has created interfaces for
The flag is off by default and can only be changed if
there are no VFs spawned on the PF. This flag will only be effective
when no PVID is set on VF and VF is not trusted.
Add new function that computes the correct VLAN ID for VF VLAN filters
based on trust, PVID, vf-vlan-prune-disable flag and current VLAN ID.
Testing Hints:
Test 1: vf-vlan-pruning == off
==============================
1. Set the private flag
> ethtool --set-priv-flag eth0 vf-vlan-pruning off (default setting)
2. Use scapy to send any VLAN tagged traffic and make sure the VF
receives all VLAN tagged traffic that matches its destination MAC
filters (unicast, multicast, and broadcast).
Test 2: vf-vlan-pruning == on
==============================
1. Set the private flag
> ethtool --set-priv-flag eth0 vf-vlan-pruning on
2. Use scapy to send any VLAN tagged traffic and make sure the VF does
not receive any VLAN tagged traffic that matches its destination MAC
filters (unicast, multicast, and broadcast).
3. Add a VLAN filter on the VF netdev
> ip link add link eth0v0 name vlan10 type vlan id 10
4. Bring the VLAN netdev up
> ip link set vlan10 up
4. Use scapy to send traffic with VLAN 10, VLAN 11 (anything not VLAN
10), and untagged traffic. Make sure the VF only receives VLAN 10
and untagged traffic when the link partner is sending.
Test 3: vf-vlan-pruning == off && VF is in a port VLAN
==============================
1. Set the private flag
> ethtool --set-priv-flag eth0 vf-vlan-pruning off (default setting)
2. Create a VF
> echo 1 > sriov_numvfs
3. Put the VF in a port VLAN
> ip link set eth0 vf 0 vlan 10
4. Use scapy to send traffic with VLAN 10 and VLAN 11 (anything not VLAN
10) and make sure the VF only receives untagged traffic when the link
partner is sending VLAN 10 tagged traffic as the VLAN tag is expected
to be stripped by HW for port VLANs and not visible to the VF.
Test 4: Change vf-vlan-pruning while VFs are created
==============================
echo 0 > sriov_numvfs
ethtool --set-priv-flag eth0 vf-vlan-pruning off
echo 1 > sriov_numvfs
ethtool --set-priv-flag eth0 vf-vlan-pruning on (expect failure)
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When the managed API is used, there is no need to explicitly call
pci_free_irq_vectors().
This looks to be a left-over from the commit in the Fixes tag. Only the
.remove() function had been updated.
So remove this unused function call and update goto label accordingly.
Fixes: 8accc467758e ("stmmac: intel: use managed PCI function on probe and resume")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Link: https://lore.kernel.org/r/1ac9b6787b0db83b0095711882c55c77c8ea8da0.1654462241.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
While at it, move these includes below the include guard.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/18731e4f6430100d6500d6c4732ee028a729c085.1654325651.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 55954f3bfdac ("net: ethernet: bgmac: move BCMA MDIO Phy code into a separate file")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220603133238.44114-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf and netfilter.
Current release - new code bugs:
- af_packet: make sure to pull the MAC header, avoid skb panic in GSO
- ptp_clockmatrix: fix inverted logic in is_single_shot()
- netfilter: flowtable: fix missing FLOWI_FLAG_ANYSRC flag
- dt-bindings: net: adin: fix adi,phy-output-clock description syntax
- wifi: iwlwifi: pcie: rename CAUSE macro, avoid MIPS build warning
Previous releases - regressions:
- Revert "net: af_key: add check for pfkey_broadcast in function
pfkey_process"
- tcp: fix tcp_mtup_probe_success vs wrong snd_cwnd
- nf_tables: disallow non-stateful expression in sets earlier
- nft_limit: clone packet limits' cost value
- nf_tables: double hook unregistration in netns path
- ping6: fix ping -6 with interface name
Previous releases - always broken:
- sched: fix memory barriers to prevent skbs from getting stuck in
lockless qdiscs
- neigh: set lower cap for neigh_managed_work rearming, avoid
constantly scheduling the probe work
- bpf: fix probe read error on big endian in ___bpf_prog_run()
- amt: memory leak and error handling fixes
Misc:
- ipv6: expand & rename accept_unsolicited_na to accept_untracked_na"
* tag 'net-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (80 commits)
net/af_packet: make sure to pull mac header
net: add debug info to __skb_pull()
net: CONFIG_DEBUG_NET depends on CONFIG_NET
stmmac: intel: Add RPL-P PCI ID
net: stmmac: use dev_err_probe() for reporting mdio bus registration failure
tipc: check attribute length for bearer name
ice: fix access-beyond-end in the switch code
nfp: remove padding in nfp_nfdk_tx_desc
ax25: Fix ax25 session cleanup problems
net: usb: qmi_wwan: Add support for Cinterion MV31 with new baseline
sfc/siena: fix wrong tx channel offset with efx_separate_tx_channels
sfc/siena: fix considering that all channels have TX queues
socket: Don't use u8 type in uapi socket.h
net/sched: act_api: fix error code in tcf_ct_flow_table_fill_tuple_ipv6()
net: ping6: Fix ping -6 with interface name
macsec: fix UAF bug for real_dev
octeontx2-af: fix error code in is_valid_offset()
wifi: mac80211: fix use-after-free in chanctx code
bonding: guard ns_targets by CONFIG_IPV6
tcp: tcp_rtx_synack() can be called from process context
...
|
|
Add PCI ID for Ethernet TSN Controller on RPL-P.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Link: https://lore.kernel.org/r/20220602073507.3955721-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I have a board where these two lines are always printed during boot:
imx-dwmac 30bf0000.ethernet: Cannot register the MDIO bus
imx-dwmac 30bf0000.ethernet: stmmac_dvr_probe: MDIO bus (id: 1) registration failed
It's perfectly fine, and the device is successfully (and silently, as
far as the console goes) probed later.
Use dev_err_probe() instead, which will demote these messages to debug
level (thus removing the alarming messages from the console) when the
error is -EPROBE_DEFER, and also has the advantage of including the
error code if/when it happens to be something other than -EPROBE_DEFER.
While here, add the missing \n to one of the format strings.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20220602074840.1143360-1-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Global `-Warray-bounds` enablement revealed some problems, one of
which is the way we define and use AQC rules messages.
In fact, they have a shared header, followed by the actual message,
which can be of one of several different formats. So it is
straightforward enough to define that header as a separate struct
and then embed it into message structures as needed, but currently
all the formats reside in one union coupled with the header. Then,
the code allocates only the memory needed for a particular message
format, leaving the union potentially incomplete.
There are no actual reads or writes beyond the end of an allocated
chunk, but at the same time, the whole implementation is fragile and
backed by an equilibrium rather than strong type and memory checks.
Define the structures the other way around: one for the common
header and the rest for the actual formats with the header embedded.
There are no places where several union members would be used at the
same time anyway. This allows to use proper struct_size() and let
the compiler know what is going to be done.
Finally, unsilence `-Warray-bounds` back for ice_switch.c.
Other little things worth mentioning:
* &ice_sw_rule_vsi_list_query is not used anywhere, remove it. It's
weird anyway to talk to hardware with purely kernel types
(bitmaps);
* expand the ICE_SW_RULE_*_SIZE() macros to pass a structure
variable name to struct_size() to let it do strict typechecking;
* rename ice_sw_rule_lkup_rx_tx::hdr to ::hdr_data to keep ::hdr
for the header structure to have the same name for it constistenly
everywhere;
* drop the duplicate of %ICE_SW_RULE_RX_TX_NO_HDR_SIZE residing in
ice_switch.h.
Fixes: 9daf8208dd4d ("ice: Add support for switch filter programming")
Fixes: 66486d8943ba ("ice: replace single-element array used for C struct hack")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220601105924.2841410-1-alexandr.lobakin@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
NFDK firmware supports 48-bit dma addressing and
parses 16 high bits of dma addresses.
In nfp_nfdk_tx_desc, dma related structure and tso
related structure are union. When "mss" be filled
with nonzero value due to enable tso, the memory used
by "padding" may be also filled. Then, firmware may
parse wrong dma addresses which causes TX watchdog
timeout problem.
This patch removes padding and unifies the dma_addr_hi
bits with the one in firmware. nfp_nfdk_tx_desc_set_dma_addr
is also added to match this change.
Fixes: c10d12e3dce8 ("nfp: add support for NFDK data path")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220601083449.50556-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-05-31
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
* tag 'mlx5-fixes-2022-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Fix mlx5_get_next_dev() peer device matching
net/mlx5e: Update netdev features after changing XDP state
net/mlx5: correct ECE offset in query qp output
net/mlx5e: Disable softirq in mlx5e_activate_rq to avoid race condition
net/mlx5: CT: Fix header-rewrite re-use for tupels
net/mlx5e: TC NIC mode, fix tc chains miss table
net/mlx5: Don't use already freed action pointer
====================
Link: https://lore.kernel.org/r/20220531205447.99236-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tx_channel_offset is calculated in efx_allocate_msix_channels, but it is
also calculated again in efx_set_channels because it was originally done
there, and when efx_allocate_msix_channels was introduced it was
forgotten to be removed from efx_set_channels.
Moreover, the old calculation is wrong when using
efx_separate_tx_channels because now we can have XDP channels after the
TX channels, so n_channels - n_tx_channels doesn't point to the first TX
channel.
Remove the old calculation from efx_set_channels, and add the
initialization of this variable if MSI or legacy interrupts are used,
next to the initialization of the rest of the related variables, where
it was missing.
This has been already done for sfc, do it also for sfc_siena.
Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Normally, all channels have RX and TX queues, but this is not true if
modparam efx_separate_tx_channels=1 is used. In that cases, some
channels only have RX queues and others only TX queues (or more
preciselly, they have them allocated, but not initialized).
Fix efx_channel_has_tx_queues to return the correct value for this case
too.
This has been already done for sfc, do it also for sfc_siena.
Messages shown at probe time before the fix:
sfc 0000:03:00.0 ens6f0np0: MC command 0x82 inlen 544 failed rc=-22 (raw=0) arg=0
------------[ cut here ]------------
netdevice: ens6f0np0: failed to initialise TXQ -1
WARNING: CPU: 1 PID: 626 at drivers/net/ethernet/sfc/ef10.c:2393 efx_ef10_tx_init+0x201/0x300 [sfc]
[...] stripped
RIP: 0010:efx_ef10_tx_init+0x201/0x300 [sfc]
[...] stripped
Call Trace:
efx_init_tx_queue+0xaa/0xf0 [sfc]
efx_start_channels+0x49/0x120 [sfc]
efx_start_all+0x1f8/0x430 [sfc]
efx_net_open+0x5a/0xe0 [sfc]
__dev_open+0xd0/0x190
__dev_change_flags+0x1b3/0x220
dev_change_flags+0x21/0x60
[...] stripped
Messages shown at remove time before the fix:
sfc 0000:03:00.0 ens6f0np0: failed to flush 10 queues
sfc 0000:03:00.0 ens6f0np0: failed to flush queues
Fixes: 8700aff08984 ("sfc: fix channel allocation with brute force")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Tested-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull vfio updates from Alex Williamson:
- Improvements to mlx5 vfio-pci variant driver, including support for
parallel migration per PF (Yishai Hadas)
- Remove redundant iommu_present() check (Robin Murphy)
- Ongoing refactoring to consolidate the VFIO driver facing API to use
vfio_device (Jason Gunthorpe)
- Use drvdata to store vfio_device among all vfio-pci and variant
drivers (Jason Gunthorpe)
- Remove redundant code now that IOMMU core manages group DMA ownership
(Jason Gunthorpe)
- Remove vfio_group from external API handling struct file ownership
(Jason Gunthorpe)
- Correct typo in uapi comments (Thomas Huth)
- Fix coccicheck detected deadlock (Wan Jiabing)
- Use rwsem to remove races and simplify code around container and kvm
association to groups (Jason Gunthorpe)
- Harden access to devices in low power states and use runtime PM to
enable d3cold support for unused devices (Abhishek Sahu)
- Fix dma_owner handling of fake IOMMU groups (Jason Gunthorpe)
- Set driver_managed_dma on vfio-pci variant drivers (Jason Gunthorpe)
- Pass KVM pointer directly rather than via notifier (Matthew Rosato)
* tag 'vfio-v5.19-rc1' of https://github.com/awilliam/linux-vfio: (38 commits)
vfio: remove VFIO_GROUP_NOTIFY_SET_KVM
vfio/pci: Add driver_managed_dma to the new vfio_pci drivers
vfio: Do not manipulate iommu dma_owner for fake iommu groups
vfio/pci: Move the unused device into low power state with runtime PM
vfio/pci: Virtualize PME related registers bits and initialize to zero
vfio/pci: Change the PF power state to D0 before enabling VFs
vfio/pci: Invalidate mmaps and block the access in D3hot power state
vfio: Change struct vfio_group::container_users to a non-atomic int
vfio: Simplify the life cycle of the group FD
vfio: Fully lock struct vfio_group::container
vfio: Split up vfio_group_get_device_fd()
vfio: Change struct vfio_group::opened from an atomic to bool
vfio: Add missing locking for struct vfio_group::kvm
kvm/vfio: Fix potential deadlock problem in vfio
include/uapi/linux/vfio.h: Fix trivial typo - _IORW should be _IOWR instead
vfio/pci: Use the struct file as the handle not the vfio_group
kvm/vfio: Remove vfio_group from kvm
vfio: Change vfio_group_set_kvm() to vfio_file_set_kvm()
vfio: Change vfio_external_check_extension() to vfio_file_enforced_coherent()
vfio: Remove vfio_external_group_match_file()
...
|
|
The is_valid_offset() function returns success/true if the call to
validate_and_get_cpt_blkaddr() fails.
Fixes: ecad2ce8c48f ("octeontx2-af: cn10k: Add mailbox to configure reassembly timeout")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YpXDrTPb8qV01JSP@kili
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In some use-cases, mlx5 instances will need to search for their peer
device (the other port on the same HCA). For that, mlx5 device matching
mechanism relied on auxiliary_find_device() to search, and used a bad matching
callback function.
This approach has two issues:
1) next_phys_dev() the matching function, assumed all devices are
of the type mlx5_adev (mlx5 auxiliary device) which is wrong and
could lead to crashes, this worked for a while, since only lately
other drivers started registering auxiliary devices.
2) using the auxiliary class bus (auxiliary_find_device) to search for
mlx5_core_dev devices, who are actually PCIe device instances, is wrong.
This works since mlx5_core always has at least one mlx5_adev instance
hanging around in the aux bus.
As suggested by others we can fix 1. by comparing device names prefixes
if they have the string "mlx5_core" in them, which is not a best practice !
but even with that fixed, still 2. needs fixing, we are trying to
match pcie device peers so we should look in the right bus (pci bus),
hence this fix.
The fix:
1) search the pci bus for mlx5 peer devices, instead of the aux bus
2) to validated devices are the same type "mlx5_core_dev" compare if
they have the same driver, which is bulletproof.
This wouldn't have worked with the aux bus since the various mlx5 aux
device types don't share the same driver, even if they share the same device
wrapper struct (mlx5_adev) "which helped to find the parent device"
Fixes: a925b5e309c9 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus")
Reported-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reported-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
|
|
Some features (LRO, HW GRO) conflict with XDP. If there is an attempt to
enable such features while XDP is active, they will be set to `off
[requested on]`. In order to activate these features after XDP is turned
off, the driver needs to call netdev_update_features(). This commit adds
this missing call after XDP state changes.
Fixes: cf6e34c8c22f ("net/mlx5e: Properly block LRO when XDP is enabled")
Fixes: b0617e7b3500 ("net/mlx5e: Properly block HW GRO when XDP is enabled")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When the driver activates the channels, it assumes NAPI isn't running
yet. mlx5e_activate_rq posts a NOP WQE to ICOSQ to trigger a hardware
interrupt and start NAPI, which will run mlx5e_alloc_rx_mpwqe and post
UMR WQEs to ICOSQ to be able to receive packets with striding RQ.
Unfortunately, a race condition is possible if NAPI is triggered by
something else (for example, TX) at a bad timing, before
mlx5e_activate_rq finishes. In this case, mlx5e_alloc_rx_mpwqe may post
UMR WQEs to ICOSQ, and with the bad timing, the wqe_info of the first
UMR may be overwritten by the wqe_info of the NOP posted by
mlx5e_activate_rq.
The consequence is that icosq->db.wqe_info[0].num_wqebbs will be changed
from MLX5E_UMR_WQEBBS to 1, disrupting the integrity of the array-based
linked list in wqe_info[]. mlx5e_poll_ico_cq will hang in an infinite
loop after processing wqe_info[0], because after the corruption, the
next item to be processed will be wqe_info[1], which is filled with
zeros, and `sqcc += wi->num_wqebbs` will never move further.
This commit fixes this race condition by using async_icosq to post the
NOP and trigger the interrupt. async_icosq is always protected with a
spinlock, eliminating the race condition.
Fixes: bc77b240b3c5 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reported-by: Karsten Nielsen <karsten@foo-bar.dk>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Tuple entries that don't have nat configured for them
which are added to the ct nat table will always create
a new modify header, as we don't check for possible
re-use on them. The same for tuples that have nat configured
for them but are added to ct table.
Fix the above by only avoiding wasteful re-use lookup
for actually natted entries in ct nat table.
Fixes: 7fac5c2eced3 ("net/mlx5: CT: Avoid reusing modify header context for natted entries")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit changed promisc table to be created on demand with the
highest priority in the NIC table replacing the vlan table, this caused
tc NIC tables miss flow to skip the prmoisc table because it use vlan
table as miss table.
OVS offload in NIC mode use promisc by default so any unicast packet
which will be handled by tc NIC tables miss flow will skip the promisc
rule and will be dropped.
Fix this by adding new empty table in new tc level with low priority and
point the nic tc chain miss to it, the new table is managed so it will
point to vlan table if promisc is disabled and to promisc table if enabled.
Fixes: 1c46d7409f30 ("net/mlx5e: Optimize promiscuous mode")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
