summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet
AgeCommit message (Collapse)AuthorFilesLines
2022-12-07net: ethernet: ti: am65-cpsw: Fix hardware switch mode on suspend/resumeRoger Quadros2-0/+9
On low power during system suspend the ALE table context is lost. Save the ALE context before suspend and restore it after resume. Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07net: ethernet: ti: am65-cpsw: retain PORT_VLAN_REG after suspend/resumeRoger Quadros2-0/+11
During suspend resume the context of PORT_VLAN_REG is lost so save it during suspend and restore it during resume for host port and slave ports. Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07net: ethernet: ti: am65-cpsw: Add suspend/resume supportRoger Quadros1-49/+173
Add PM handlers for System suspend/resume. As DMA driver doesn't yet support suspend/resume we free up the DMA channels at suspend and acquire and initialize them at resume. In this revised approach we do not free the TX/RX IRQs at am65_cpsw_nuss_common_stop() as it causes problems. We will now free them only on .suspend() as we need to release the DMA channels (as DMA looses context) and re-acquiring them on .resume() may not necessarily give us the same IRQs. To make this easier: - introduce am65_cpsw_nuss_remove_rx_chns() which is similar to am65_cpsw_nuss_remove_tx_chns(). These will be invoked in pm.suspend() to release the DMA channels and free up the IRQs. - move napi_add() and request_irq() calls to am65_cpsw_nuss_init_rx/tx_chns() so we can invoke them in pm.resume() to acquire the DMA channels and IRQs. As CPTS looses contect during suspend/resume, invoke the necessary CPTS suspend/resume helpers. ALE_CLEAR command is issued in cpsw_ale_start() so no need to issue it before the call to cpsw_ale_start(). Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07Revert "net: ethernet: ti: am65-cpsw: Add suspend/resume support"Roger Quadros1-166/+55
This reverts commit fd23df72f2be317d38d9fde0a8996b8e7454fd2a. This commit broke set channel operation. Revert this and implement it with a different approach in a separate patch. Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07Revert "net: ethernet: ti: am65-cpsw: retain PORT_VLAN_REG after suspend/resume"Roger Quadros2-11/+0
This reverts commit 643cf0e3ab5ccee37b3c53c018bd476c45c4b70e. This is to make it easier to revert the offending commit fd23df72f2be ("net: ethernet: ti: am65-cpsw: Add suspend/resume support") Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07Revert "net: ethernet: ti: am65-cpsw: Fix hardware switch mode on ↵Roger Quadros2-9/+0
suspend/resume" This reverts commit 1af3cb3702d02167926a2bd18580cecb2d64fd94. This is to make it easier to revert the offending commit fd23df72f2be ("net: ethernet: ti: am65-cpsw: Add suspend/resume support") Signed-off-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07net/mlx5: E-Switch, Implement devlink port function cmds to control migratableShay Drory4-0/+116
Implement devlink port function commands to enable / disable migratable. This is used to control the migratable capability of the device. Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Acked-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07net/mlx5: E-Switch, Implement devlink port function cmds to control RoCEYishai Hadas6-1/+176
Implement devlink port function commands to enable / disable RoCE. This is used to control the RoCE device capabilities. This patch implement infrastructure which will be used by downstream patches that will add additional capabilities. Signed-off-by: Yishai Hadas <yishaih@nvidia.com> Signed-off-by: Daniel Jurgens <danielj@nvidia.com> Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Acked-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07net/mlx5: Add generic getters for other functions capsShay Drory4-5/+9
Downstream patch requires to get other function GENERAL2 caps while mlx5_vport_get_other_func_cap() gets only one type of caps (general). Rename it to represent this and introduce a generic implementation of mlx5_vport_get_other_func_cap(). Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Acked-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-07octeontx2-af: Add FEC stats for RPM/RPM_USX blockHariprasad Kelam5-2/+82
CN10K silicon MAC block RPM and CN10KB silicon MAC block RPM_USX both support BASER and RSFEC modes. Also MAC (CGX) on OcteonTx2 silicon variants and MAC (RPM) on OcteonTx3 CN10K are different and FEC stats need to be read differently. CN10KB MAC block (RPM_USX) fec csr offsets are same as CN10K MAC block (RPM) mac_ops points to same fn(). Upper layer interface between RVU AF and PF netdev is kept same. Based on silicon variant appropriate fn() pointer is called to read FEC stats Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-07octeontx2-pf: ethtool: Implement get_fec_statsHariprasad Kelam1-0/+34
This patch registers a callback for get_fec_stats such that FEC stats can be queried from the below command "ethtool -I --show-fec eth0" Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-07octeontx2-af: cn10kb: Add RPM_USX MAC supportHariprasad Kelam8-41/+270
OcteonTx2's next gen platform the CN10KB has RPM_USX MAC which has a different serdes when compared to RPM MAC. Though the underlying HW is different, the CSR interface has been designed largely inline with RPM MAC, with few exceptions though. So we are using the same CGX driver for RPM_USX MAC as well and will have a different set of APIs for RPM_USX where ever necessary. The RPM and RPM_USX blocks support a different number of LMACS. RPM_USX support 8 LMACS per MAC block whereas legacy RPM supports only 4 LMACS per MAC. with this RPM_USX support double the number of DMAC filters and fifo size. This patch adds initial support for CN10KB's RPM_USX MAC i.e registering the driver and defining MAC operations (mac_ops). Adds the logic to configure internal loopback and pause frames and assign FIFO length to LMACS. Kernel reads lmac features like lmac type, autoneg, etc from shared firmware data this structure only supports 4 lmacs per MAC, this patch extends this structure to accommodate 8 lmacs. Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-07octeontx2-af: Support variable number of lmacsRakesh Babu Saladi8-40/+42
Most of the code in CGX/RPM driver assumes that max lmacs per given MAC as always, 4 and the number of MAC blocks also as 4. With this assumption, the max number of interfaces supported is hardcoded to 16. This creates a problem as next gen CN10KB silicon MAC supports 8 lmacs per MAC block. This patch solves the problem by using "max lmac per MAC block" value from constant csrs and uses cgx_cnt_max value which is populated based number of MAC blocks supported by silicon. Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com> Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-07net: ethernet: mtk_wed: Fix missing of_node_put() in mtk_wed_wo_hardware_init()Yuan Can1-3/+6
The np needs to be released through of_node_put() in the error handling path of mtk_wed_wo_hardware_init(). Fixes: 799684448e3e ("net: ethernet: mtk_wed: introduce wed wo support") Signed-off-by: Yuan Can <yuancan@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20221205034339.112163-1-yuancan@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-06net: ethernet: mtk_wed: add reset to rx_ring_setup callbackLorenzo Bianconi1-7/+13
This patch adds reset parameter to mtk_wed_rx_ring_setup signature in order to align rx_ring_setup callback to tx_ring_setup one introduced in 'commit 23dca7a90017 ("net: ethernet: mtk_wed: add reset to tx_ring_setup callback")' Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/29c6e7a5469e784406cf3e2920351d1207713d05.1670239984.git.lorenzo@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-06net: microchip: vcap: Remove unneeded semicolonszhang songyi1-2/+2
Semicolons after "}" are not needed. Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/202212051422158113766@zte.com.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-06sfc: use sysfs_emit() to instead of scnprintf()ye xingchen2-2/+2
Follow the advice of the Documentation/filesystems/sysfs.rst and show() should only use sysfs_emit() or sysfs_emit_at() when formatting the value to be returned to user space. Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Link: https://lore.kernel.org/r/202212051021451139126@zte.com.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-06net: lan966x: Add ptp trap rulesHoratiu Vultur5-23/+265
Currently lan966x, doesn't allow to run PTP over interfaces that are part of the bridge. The reason is when the lan966x was receiving a PTP frame (regardless if L2/IPv4/IPv6) the HW it would flood this frame. Now that it is possible to add VCAP rules to the HW, such to trap these frames to the CPU, it is possible to run PTP also over interfaces that are part of the bridge. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-06net: microchip: vcap: Add vcap_rule_get_key_u32Horatiu Vultur2-0/+20
Add the function vcap_rule_get_key_u32 which allows to get the value and the mask of a key that exist on the rule. If the key doesn't exist, it would return error. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-06net: microchip: vcap: Add vcap_mod_ruleHoratiu Vultur2-0/+38
Add the function vcap_mod_rule which allows to update an existing rule in the vcap. It is required for the rule to exist in the vcap to be able to modify it. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-06net: microchip: vcap: Add vcap_get_ruleHoratiu Vultur4-438/+848
Add function vcap_get_rule which returns a rule based on the internal rule id. The entire functionality of reading and decoding the rule from the VCAP was inside vcap_api_debugfs file. So move the entire implementation in vcap_api as this is used also by vcap_get_rule. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-05net: mtk_eth_soc: enable flow offload support for MT7986 SoCLorenzo Bianconi1-0/+1
Since Wireless Ethernet Dispatcher is now available for mt7986 in mt76, enable hw flow support for MT7986 SoC. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/fdcaacd827938e6a8c4aa1ac2c13e46d2c08c821.1670072898.git.lorenzo@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-05nfp: add support for multicast filterDiana Wang3-4/+79
Rewrite nfp_net_set_rx_mode() to implement interface to delivery mc address and operations to firmware by using general mailbox for filtering multicast packets. The operations include add mc address and delete mc address. And the limitation of mc addresses number is 1024 for each net device. User triggers adding mc address by using command below: ip maddress add <mc address> dev <interface name> User triggers deleting mc address by using command below: ip maddress del <mc address> dev <interface name> Signed-off-by: Diana Wang <na.wang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-12-05net: stmmac: tegra: Add MGBE supportBhadram Varka3-0/+398
Add support for the Multi-Gigabit Ethernet (MGBE/XPCS) IP found on NVIDIA Tegra234 SoCs. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Bhadram Varka <vbhadram@nvidia.com> Co-developed-by: Revanth Kumar Uppala <ruppala@nvidia.com> Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com> Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-12-05net: stmmac: Power up SERDES after the PHY linkRevanth Kumar Uppala1-2/+5
The Tegra MGBE ethernet controller requires that the SERDES link is powered-up after the PHY link is up, otherwise the link fails to become ready following a resume from suspend. Add a variable to indicate that the SERDES link must be powered-up after the PHY link. Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com> Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-12-03r8169: enable GRO software interrupt coalescing per defaultHeiner Kallweit1-0/+2
There are reports about r8169 not reaching full line speed on certain systems (e.g. SBC's) with a 2.5Gbps link. There was a time when hardware interrupt coalescing was enabled per default, but this was changed due to ASPM-related issues on few systems. So let's use software interrupt coalescing instead and enable it using new function netdev_sw_irq_coalesce_default_on(). Even with these conservative settings interrupt load on my 1Gbps test system reduced significantly. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-12-02net: ethernet: mtk_wed: fix sleep while atomic in mtk_wed_wo_queue_refillLorenzo Bianconi1-5/+6
In order to fix the following sleep while atomic bug always alloc pages with GFP_ATOMIC in mtk_wed_wo_queue_refill since page_frag_alloc runs in spin_lock critical section. [ 9.049719] Hardware name: MediaTek MT7986a RFB (DT) [ 9.054665] Call trace: [ 9.057096] dump_backtrace+0x0/0x154 [ 9.060751] show_stack+0x14/0x1c [ 9.064052] dump_stack_lvl+0x64/0x7c [ 9.067702] dump_stack+0x14/0x2c [ 9.071001] ___might_sleep+0xec/0x120 [ 9.074736] __might_sleep+0x4c/0x9c [ 9.078296] __alloc_pages+0x184/0x2e4 [ 9.082030] page_frag_alloc_align+0x98/0x1ac [ 9.086369] mtk_wed_wo_queue_refill+0x134/0x234 [ 9.090974] mtk_wed_wo_init+0x174/0x2c0 [ 9.094881] mtk_wed_attach+0x7c8/0x7e0 [ 9.098701] mt7915_mmio_wed_init+0x1f0/0x3a0 [mt7915e] [ 9.103940] mt7915_pci_probe+0xec/0x3bc [mt7915e] [ 9.108727] pci_device_probe+0xac/0x13c [ 9.112638] really_probe.part.0+0x98/0x2f4 [ 9.116807] __driver_probe_device+0x94/0x13c [ 9.121147] driver_probe_device+0x40/0x114 [ 9.125314] __driver_attach+0x7c/0x180 [ 9.129133] bus_for_each_dev+0x5c/0x90 [ 9.132953] driver_attach+0x20/0x2c [ 9.136513] bus_add_driver+0x104/0x1fc [ 9.140333] driver_register+0x74/0x120 [ 9.144153] __pci_register_driver+0x40/0x50 [ 9.148407] mt7915_init+0x5c/0x1000 [mt7915e] [ 9.152848] do_one_initcall+0x40/0x25c [ 9.156669] do_init_module+0x44/0x230 [ 9.160403] load_module+0x1f30/0x2750 [ 9.164135] __do_sys_init_module+0x150/0x200 [ 9.168475] __arm64_sys_init_module+0x18/0x20 [ 9.172901] invoke_syscall.constprop.0+0x4c/0xe0 [ 9.177589] do_el0_svc+0x48/0xe0 [ 9.180889] el0_svc+0x14/0x50 [ 9.183929] el0t_64_sync_handler+0x9c/0x120 [ 9.188183] el0t_64_sync+0x158/0x15c Fixes: 799684448e3e ("net: ethernet: mtk_wed: introduce wed wo support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/67ca94bdd3d9eaeb86e52b3050fbca0bcf7bb02f.1669908312.git.lorenzo@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-02tsnep: Rework RX buffer allocationGerhard Engleder3-74/+140
Refill RX queue in batches of descriptors to improve performance. Refill is allowed to fail as long as a minimum number of descriptors is active. Thus, a limited number of failed RX buffer allocations is now allowed for normal operation. Previously every failed allocation resulted in a dropped frame. If the minimum number of active descriptors is reached, then RX buffers are still reused and frames are dropped. This ensures that the RX queue never runs empty and always continues to operate. Prework for future XDP support. Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-12-02tsnep: Throttle interruptsGerhard Engleder4-0/+187
Without interrupt throttling, iperf server mode generates a CPU load of 100% (A53 1.2GHz). Also the throughput suffers with less than 900Mbit/s on a 1Gbit/s link. The reason is a high interrupt load with interrupts every ~20us. Reduce interrupt load by throttling of interrupts. Interrupt delay default is 64us. For iperf server mode the CPU load is significantly reduced to ~20% and the throughput reaches the maximum of 941MBit/s. Interrupts are generated every ~140us. RX and TX coalesce can be configured with ethtool. RX coalesce has priority over TX coalesce if the same interrupt is used. Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-12-02tsnep: Add ethtool::get_channels supportGerhard Engleder1-0/+12
Allow user space to read number of TX and RX queue. This is useful for device dependent qdisc configurations like TAPRIO with hardware offload. Also ethtool::get_per_queue_coalesce / set_per_queue_coalesce requires that interface. Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-12-02tsnep: Consistent naming of struct net_deviceGerhard Engleder1-6/+6
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-12-01bnxt: report FEC block stats via standard interfaceJakub Kicinski1-0/+8
I must have missed that these stats are only exposed via the unstructured ethtool -S when they got merged. Plumb in the structured form. Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20221130013108.90062-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-12-01r8169: use tp_to_dev instead of open codeJuhee Kang1-2/+3
The open code is defined as a helper function(tp_to_dev) on r8169_main.c, which the open code is &tp->pci_dev->dev. The helper function was added in commit 1e1205b7d3e9 ("r8169: add helper tp_to_dev"). And then later, commit f1e911d5d0df ("r8169: add basic phylib support") added r8169_phylink_handler function but it didn't use the helper function. Thus, tp_to_dev() replaces the open code. This patch doesn't change logic. Signed-off-by: Juhee Kang <claudiajkang@gmail.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/20221129161244.5356-1-claudiajkang@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-mac: move rtnl_lock() only around phylink_{,dis}connect_phy()Vladimir Oltean3-8/+5
After the introduction of a private mac_lock that serializes access to priv->mac (and port_priv->mac in the switch), the only remaining purpose of rtnl_lock() is to satisfy the locking requirements of phylink_fwnode_phy_connect() and phylink_disconnect_phy(). But the functions these live in, dpaa2_mac_connect() and dpaa2_mac_disconnect(), have contradictory locking requirements. While phylink_fwnode_phy_connect() wants rtnl_lock() to be held, phylink_create() wants it to not be held. Move the rtnl_lock() from top-level (in the dpaa2-eth and dpaa2-switch drivers) to only surround the phylink calls that require it, in the dpaa2-mac library code. This is possible because dpaa2_mac_connect() and dpaa2_mac_disconnect() run unlocked, and there isn't any danger of an AB/BA deadlock between the rtnl_mutex and other private locks. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-switch: serialize changes to priv->mac with a mutexVladimir Oltean3-10/+55
The dpaa2-switch driver uses a DPMAC in the same way as the dpaa2-eth driver, so we need to duplicate the locking solution established by the previous change to the switch driver as well. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-eth: serialize changes to priv->mac with a mutexVladimir Oltean3-16/+91
The dpaa2 architecture permits dynamic connections between objects on the fsl-mc bus, specifically between a DPNI object (represented by a struct net_device) and a DPMAC object (represented by a struct phylink). The DPNI driver is notified when those connections are created/broken through the dpni_irq0_handler_thread() method. To ensure that ethtool operations, as well as netdev up/down operations serialize with the connection/disconnection of the DPNI with a DPMAC, dpni_irq0_handler_thread() takes the rtnl_lock() to block those other operations from taking place. There is code called by dpaa2_mac_connect() which wants to acquire the rtnl_mutex once again, see phylink_create() -> phylink_register_sfp() -> sfp_bus_add_upstream() -> rtnl_lock(). So the strategy doesn't quite work out, even though it's fairly simple. Create a different strategy, where all code paths in the dpaa2-eth driver access priv->mac only while they are holding priv->mac_lock. The phylink instance is not created or connected to the PHY under the priv->mac_lock, but only assigned to priv->mac then. This will eliminate the reliance on the rtnl_mutex. Add lockdep annotations and put comments where holding the lock is not necessary, and priv->mac can be dereferenced freely. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-eth: connect to MAC before requesting the "endpoint changed" IRQVladimir Oltean1-9/+9
dpaa2_eth_connect_mac() is called both from dpaa2_eth_probe() and from dpni_irq0_handler_thread(). It could happen that the DPNI gets connected to a DPMAC on the fsl-mc bus exactly during probe, as soon as the "endpoint change" interrupt is requested in dpaa2_eth_setup_irqs(). This will cause the dpni_irq0_handler_thread() to register a phylink instance for that DPMAC. Then, the probing function will also try to register a phylink instance for the same DPMAC, operation which should fail (and this will fail the probing of the driver). Reorder dpaa2_eth_setup_irqs() and dpaa2_eth_connect_mac(), such that dpni_irq0_handler_thread() never races with the DPMAC-related portion of the probing path. Also reorder dpaa2_eth_disconnect_mac() to be in the mirror position of dpaa2_eth_connect_mac() in the teardown path. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-switch replace direct MAC access with dpaa2_switch_port_has_mac()Vladimir Oltean1-1/+1
The helper function will gain a lockdep annotation in a future patch. Make sure to benefit from it. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2: publish MAC stringset to ethtool -S even if MAC is missingVladimir Oltean2-18/+5
DPNIs and DPSW objects can connect and disconnect at runtime from DPMAC objects on the same fsl-mc bus. The DPMAC object also holds "ethtool -S" unstructured counters. Those counters are only shown for the entity owning the netdev (DPNI, DPSW) if it's connected to a DPMAC. The ethtool stringset code path is split into multiple callbacks, but currently, connecting and disconnecting the DPMAC takes the rtnl_lock(). This blocks the entire ethtool code path from running, see ethnl_default_doit() -> rtnl_lock() -> ops->prepare_data() -> strset_prepare_data(). This is going to be a problem if we are going to no longer require rtnl_lock() when connecting/disconnecting the DPMAC, because the DPMAC could appear between ops->get_sset_count() and ops->get_strings(). If it appears out of the blue, we will provide a stringset into an array that was dimensioned thinking the DPMAC wouldn't be there => array accessed out of bounds. There isn't really a good way to work around that, and I don't want to put too much pressure on the ethtool framework by playing locking games. Just make the DPMAC counters be always available. They'll be zeroes if the DPNI or DPSW isn't connected to a DPMAC. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-switch: assign port_priv->mac after dpaa2_mac_connect() callVladimir Oltean1-9/+12
The dpaa2-switch has the exact same locking requirements when connected to a DPMAC, so it needs port_priv->mac to always point either to NULL, or to a DPMAC with a fully initialized phylink instance. Make the same preparatory change in the dpaa2-switch driver as in the dpaa2-eth one. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-eth: assign priv->mac after dpaa2_mac_connect() callVladimir Oltean1-9/+12
There are 2 requirements for correct code: - Any time the driver accesses the priv->mac pointer at runtime, it either holds NULL to indicate a DPNI-DPNI connection (or unconnected DPNI), or a struct dpaa2_mac whose phylink instance was fully initialized (created and connected to the PHY). No changes are made to priv->mac while it is being used. Currently, rtnl_lock() watches over the call to dpaa2_eth_connect_mac(), so it serves the purpose of serializing this with all readers of priv->mac. - dpaa2_mac_connect() should run unlocked, because inside it are 2 phylink calls with incompatible locking requirements: phylink_create() requires that the rtnl_mutex isn't held, and phylink_fwnode_phy_connect() requires that the rtnl_mutex is held. The only way to solve those contradictory requirements is to let dpaa2_mac_connect() take rtnl_lock() when it needs to. To solve both requirements, we need to identify the writer side of the priv->mac pointer, which can be wrapped in a mutex private to the driver in a future patch. The dpaa2_mac_connect() cannot be part of the writer side critical section, because of an AB/BA deadlock with rtnl_lock(). So the strategy needs to be that where we prepare the DPMAC by calling dpaa2_mac_connect(), and only make priv->mac point to it once it's fully prepared. This ensures that the writer side critical section has the absolute minimum surface it can. The reverse strategy is adopted in the dpaa2_eth_disconnect_mac() code path. This makes sure that priv->mac is NULL when we start tearing down the DPMAC that we disconnected from, and concurrent code will simply not see it. No locking changes in this patch (concurrent code is still blocked by the rtnl_mutex). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-mac: remove defensive check in dpaa2_mac_disconnect()Vladimir Oltean1-3/+0
dpaa2_mac_disconnect() will only be called with a NULL mac->phylink if dpaa2_mac_connect() failed, or was never called. The callers are these: dpaa2_eth_disconnect_mac(): if (dpaa2_eth_is_type_phy(priv)) dpaa2_mac_disconnect(priv->mac); dpaa2_switch_port_disconnect_mac(): if (dpaa2_switch_port_is_type_phy(port_priv)) dpaa2_mac_disconnect(port_priv->mac); priv->mac can be NULL, but in that case, dpaa2_eth_is_type_phy() returns false, and dpaa2_mac_disconnect() is never called. Similar for dpaa2-switch. When priv->mac is non-NULL, it means that dpaa2_mac_connect() returned zero (success), and therefore, priv->mac->phylink is also a valid pointer. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-mac: absorb phylink_start() call into dpaa2_mac_start()Vladimir Oltean3-8/+10
The phylink handling is intended to be hidden inside the dpaa2_mac object. Move the phylink_start() call into dpaa2_mac_start(), and phylink_stop() into dpaa2_mac_stop(). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2: replace dpaa2_mac_is_type_fixed() with dpaa2_mac_is_type_phy()Vladimir Oltean3-14/+10
dpaa2_mac_is_type_fixed() is a header with no implementation and no callers, which is referenced from the documentation though. It can be deleted. On the other hand, it would be useful to reuse the code between dpaa2_eth_is_type_phy() and dpaa2_switch_port_is_type_phy(). That common code should be called dpaa2_mac_is_type_phy(), so let's create that. The removal and the addition are merged into the same patch because, in fact, is_type_phy() is the logical opposite of is_type_fixed(). Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: dpaa2-eth: don't use -ENOTSUPP error codeVladimir Oltean2-2/+2
dpaa2_eth_setup_dpni() is called from the probe path and dpaa2_eth_set_link_ksettings() is propagated to user space. include/linux/errno.h says that ENOTSUPP is "Defined for the NFSv3 protocol". Conventional wisdom has it to not use it in networking drivers. Replace it with -EOPNOTSUPP. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-12-01net: microchip: sparx5: Fix error handling in vcap_show_admin()Dan Carpenter1-4/+11
If vcap_dup_rule() fails that leads to an error pointer dereference side the call to vcap_free_rule(). Also it only returns an error if the very last call to vcap_read_rule() fails and it returns success for other errors. I've changed it to just stop printing after the first error and return an error code. Fixes: 3a7921560d2f ("net: microchip: sparx5: Add VCAP rule debugFS support for the VCAP API") Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com> Link: https://lore.kernel.org/r/Y4XUUx9kzurBN+BV@kili Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-11-30Merge tag 'mlx5-updates-2022-11-29' of ↵Jakub Kicinski17-79/+101
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2022-11-29 Misc update for mlx5 driver 1) Various trivial cleanups 2) Maor Dickman, Adds support for trap offload with additional actions 3) From Tariq, UMR (device memory registrations) cleanups, UMR WQE must be aligned to 64B per device spec, (not a bug fix). * tag 'mlx5-updates-2022-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5e: Support devlink reload of IPsec core net/mlx5e: TC, Add offload support for trap with additional actions net/mlx5e: Do early return when setup vports dests for slow path flow net/mlx5: Remove redundant check net/mlx5e: Delete always true DMA check net/mlx5e: Don't access directly DMA device pointer net/mlx5e: Don't use termination table when redundant net/mlx5: Fix orthography errors in documentation net/mlx5: Use generic definition for UMR KLM alignment net/mlx5: Generalize name of UMR alignment definition net/mlx5: Remove unused UMR MTT definitions net/mlx5e: Add padding when needed in UMR WQEs net/mlx5: Remove unused ctx variables net/mlx5e: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper net/mlx5e: Remove unneeded io-mapping.h #include ==================== Link: https://lore.kernel.org/r/20221130051152.479480-1-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-11-30net: devlink: clean-up empty devlink_ops::info_get()Vincent Mailhol3-22/+0
devlink_ops::info_get() is now optional and devlink will continue to report information even if that callback gets removed. Remove all the empty devlink_ops::info_get() callbacks from the drivers. Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-11-30net: devlink: let the core report the driver name instead of the driversVincent Mailhol14-66/+4
The driver name is available in device_driver::name. Right now, drivers still have to report this piece of information themselves in their devlink_ops::info_get callback function. In order to factorize code, make devlink_nl_info_fill() add the driver name attribute. Now that the core sets the driver name attribute, drivers are not supposed to call devlink_info_driver_name_put() anymore. Remove devlink_info_driver_name_put() and clean-up all the drivers using this function in their callback. Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-11-30ice: implement direct read for NVM and Shadow RAM regionsJacob Keller1-0/+69
Implement the .read handler for the NVM and Shadow RAM regions. This enables user space to read a small chunk of the flash without needing the overhead of creating a full snapshot. Update the documentation for ice to detail which regions have direct read support. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-20 00:43:28 +0000