| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix system hang with below sequences:
~# ifconfig ethx down
~# ifconfig ethx hw ether xx:xx:xx:xx:xx:xx
After ethx down, stmmac all clocks gated off and then register access causes
system hang.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This should be a mistake to fix conflicts when removing RFC tag to
repost the patch.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link xpcs callback functions for MAC to configure the xpcs EEE feature.
The clk_eee frequency is used to calculate the MULT_FACT_100NS. This is
to adjust the clock tic closer to 100ns.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add constants and callback functions for the dwmac present
on RK3566/RK3568 SoCs.
RK3568 has two MACs, and RK3566 just one, but it's otherwise
the same IP core.
Signed-off-by: David Wu <david.wu@rock-chips.com>
[Ezequiel: Separate rk3566-gmac support]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a check for non-null struct rk_gmac_ops for the
configured PHY interface mode, failing if unsupported.
Signed-off-by: David Wu <david.wu@rock-chips.com>
[Ezequiel: Refactor so it fails if unsupported]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Rockchip platforms have a GMAC4 core, and therefore
'plat_stmmacenet_data.has_gmac' shouldn't be set if
'plat_stmmacenet_data.has_gmac4' is set.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the xdp_{init,prepare}_buff() helpers instead of
an open-coded version.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Rockchip RK3308 SoC has a gmac with only the RMII interface signals
exposed.
This patch adds support for it.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case clk_prepare() fails, capture and propagate the error code up the
stack. If regulator_enable() was called earlier, properly unwind it by
calling regulator_disable().
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-22-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit f86a3b83833e7cfe558ca4d70b64ebc48903efec.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit causes a memory leak when it is trying to claim it
is properly handling errors. Revert this change and fix it up properly
in a follow-on commit.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: David S. Miller <davem@davemloft.net>
Fixes: f86a3b83833e ("net: stmicro: fix a missing check of clk_prepare")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-21-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Both get and set WoL will check device_can_wakeup(), if MAC supports PMT, it
will set device wakeup capability. After commit 1d8e5b0f3f2c ("net: stmmac:
Support WOL with phy"), device wakeup capability will be overwrite in
stmmac_init_phy() according to phy's Wol feature. If phy doesn't support WoL,
then MAC will lose wakeup capability. To fix this issue, only overwrite device
wakeup capability when MAC doesn't support PMT.
For STMMAC now driver checks MAC's WoL capability if MAC supports PMT, if
not support, driver will check PHY's WoL capability.
Fixes: 1d8e5b0f3f2c ("net: stmmac: Support WOL with phy")
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The statement of the last "if (xxx)" branch is the same as the "else"
branch. Delete it to simplify code.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RX FIFO overflows when the system is not able to process all received
packets and they start accumulating (first in the DMA queue in memory,
then in the FIFO). An interrupt is then raised for each overflowing packet
and handled in stmmac_interrupt(). This is counter-productive, since it
brings the system (or more likely, one CPU core) to its knees to process
the FIFO overflow interrupts.
stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr
into the corresponding hardware register (according to the MAC spec, this
has the effect of restarting the MAC DMA). However, without freeing any rx
descriptors, the DMA stops right away, and another overflow interrupt is
raised as the FIFO overflows again. Since the DMA is already restarted at
the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO
overflow interrupts and the corresponding handling code has no side effect,
and eliminates the interrupt storm when the RX FIFO overflows.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210506143312.20784-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In promiscuous mode Receive All bit is set in GMAC packet filter register,
but outside promiscuous mode Receive All bit is not cleared,
which resulted in all network packets are received when toggle (ON/OFF)
the promiscuous mode.
Fixes: e0f9956a3862 ("net: stmmac: Add option for VLAN filter fail queue enable")
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit f4da56529da60 ("net: stmmac: Add support for external
trigger timestamping"), struct stmmac_priv was declared at line 507
which caused duplicate struct declarations.
Remove later duplicate declaration here.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An issue found when network interface is down and up again, FPE handshake
fails to trigger. This is due to __FPE_REMOVING bit remains being set in
stmmac_fpe_stop_wq() but not cleared in stmmac_fpe_start_wq(). This
cause FPE workqueue task, stmmac_fpe_lp_task() not able to be executed.
To fix this, add clearing __FPE_REMOVING bit in stmmac_fpe_start_wq().
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
|
|
|
|
Enable HW descriptor prefetch by default by setting plat->dma_cfg->dche =
true in intel_mgbe_common_data(). Need to be noted that this capability
only be supported in DWMAC core version 5.20 onwards. In stmmac, there is
a checking to check the core version. If the core version is below 5.20,
this capability wouldn`t be configured.
Below is the iperf result comparison between HW descriptor prefetch
disabled(DCHE=0b) and enabled(DCHE=1b). Tested on Intel Elkhartlake
platform with DWMAC Core 5.20. Observed line rate performance
improvement with HW descriptor prefetch enabled.
DCHE = 0b
[ 5] local 169.254.1.162 port 42123 connected to 169.254.244.142 port 5201
[ ID] Interval Transfer Bitrate Total Datagrams
[ 5] 0.00-1.00 sec 96.7 MBytes 811 Mbits/sec 70050
[ 5] 1.00-2.00 sec 96.5 MBytes 809 Mbits/sec 69850
[ 5] 2.00-3.00 sec 96.3 MBytes 808 Mbits/sec 69720
[ 5] 3.00-4.00 sec 95.9 MBytes 804 Mbits/sec 69450
[ 5] 4.00-5.00 sec 96.0 MBytes 806 Mbits/sec 69530
[ 5] 5.00-6.00 sec 96.8 MBytes 812 Mbits/sec 70080
[ 5] 6.00-7.00 sec 96.9 MBytes 813 Mbits/sec 70140
[ 5] 7.00-8.00 sec 96.8 MBytes 812 Mbits/sec 70080
[ 5] 8.00-9.00 sec 97.0 MBytes 814 Mbits/sec 70230
[ 5] 9.00-10.00 sec 96.9 MBytes 813 Mbits/sec 70170
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 966 MBytes 810 Mbits/sec 0.000 ms 0/699300 (0%) sender
[ 5] 0.00-10.00 sec 966 MBytes 810 Mbits/sec 0.011 ms 0/699265 (0%) receiver
DCHE = 1b
[ 5] local 169.254.1.162 port 49740 connected to 169.254.244.142 port 5201
[ ID] Interval Transfer Bitrate Total Datagrams
[ 5] 0.00-1.00 sec 97.9 MBytes 821 Mbits/sec 70880
[ 5] 1.00-2.00 sec 98.1 MBytes 823 Mbits/sec 71060
[ 5] 2.00-3.00 sec 98.2 MBytes 824 Mbits/sec 71140
[ 5] 3.00-4.00 sec 98.2 MBytes 824 Mbits/sec 71090
[ 5] 4.00-5.00 sec 98.1 MBytes 823 Mbits/sec 71050
[ 5] 5.00-6.00 sec 98.1 MBytes 823 Mbits/sec 71040
[ 5] 6.00-7.00 sec 98.1 MBytes 823 Mbits/sec 71050
[ 5] 7.00-8.00 sec 98.2 MBytes 824 Mbits/sec 71140
[ 5] 8.00-9.00 sec 98.2 MBytes 824 Mbits/sec 71120
[ 5] 9.00-10.00 sec 98.3 MBytes 824 Mbits/sec 71150
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 981 MBytes 823 Mbits/sec 0.000 ms 0/710720 (0%) sender
[ 5] 0.00-10.00 sec 981 MBytes 823 Mbits/sec 0.041 ms 0/710650 (0%) receiver
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DWMAC Core 5.20 onwards supports HW descriptor prefetching.
Additionally, it also depends on platform specific RTL configuration.
This capability could be enabled by setting DMA_Mode bit-19 (DCHE).
So, to enable this cability, platform must set plat->dma_cfg->dche = true
and the DWMAC core version must be 5.20 onwards. Else, this capability
wouldn`t be configured
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TSO and TBS cannot co-exist and current implementation requires two
fixes:
1) stmmac_open() does not need to call stmmac_enable_tbs() because
the MAC is reset in stmmac_init_dma_engine() anyway.
2) Inside stmmac_hw_setup(), we should call stmmac_enable_tso() for
TX Q that is _not_ configured for TBS.
Fixes: 579a25a854d4 ("net: stmmac: Initial support for TBS")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TSO and TBS cannot coexist, for now we set Intel mGbE controller to use
below TX Queue mapping: TxQ0 uses TSO and the rest of TXQs supports TBS.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently added some new locking to this function but one error path
was overlooked. We need to drop the lock before returning.
Fixes: f4da56529da6 ("net: stmmac: Add support for external trigger timestamping")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On driver probe, kmemleak reported the following memory leak which was
due to allocated bitmap that was not being freed in stmmac_dvr_probe().
unreferenced object 0xffff9276014b13c0 (size 8):
comm "systemd-udevd", pid 2143, jiffies 4294681112 (age 116.720s)
hex dump (first 8 bytes):
00 00 00 00 00 00 00 00 ........
backtrace:
[<00000000c51e34b2>] stmmac_dvr_probe+0x1c0/0x440 [stmmac]
[<00000000b530eb41>] intel_eth_pci_probe.cold+0x2b/0x14e [dwmac_intel]
[<00000000b10f8929>] pci_device_probe+0xd2/0x150
[<00000000fb254c74>] really_probe+0xf8/0x410
[<0000000034128a59>] driver_probe_device+0x5d/0x150
[<00000000016104d5>] device_driver_attach+0x53/0x60
[<00000000cb18cd07>] __driver_attach+0x96/0x140
[<00000000da9ffd5c>] bus_for_each_dev+0x7a/0xc0
[<00000000af061a88>] bus_add_driver+0x184/0x1f0
[<000000008be5c1c5>] driver_register+0x6c/0xc0
[<0000000052b18a9e>] do_one_initcall+0x4d/0x210
[<00000000154d4f07>] do_init_module+0x5c/0x230
[<000000009b648d09>] load_module+0x2a5a/0x2d40
[<000000000d86b76d>] __do_sys_finit_module+0xb5/0x120
[<000000002b0cef95>] do_syscall_64+0x33/0x40
[<0000000067b45bbb>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy")
Cc: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 9c63faaa931e443e7abbbee9de0169f1d4710546, which
introduces a suspend/resume regression on Jetson TX2 boards that can be
reproduced every time. Given that the issue that this was supposed to
fix only occurs very sporadically the safest course of action is to
revert before v5.12 and then we can have another go at fixing the more
rare issue in the next release (and perhaps backport it if necessary).
The root cause of the observed problem seems to be that when the system
is suspended, some packets are still in transit. When the descriptors
for these buffers are cleared on resume, the descriptors become invalid
and cause a fatal bus error.
Link: https://lore.kernel.org/r/708edb92-a5df-ecc4-3126-5ab36707e275@nvidia.com/
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Synopsis MAC controller supports auxiliary snapshot feature that
allows user to store a snapshot of the system time based on an external
event.
This patch add supports to the above mentioned feature. Users will be
able to triggered capturing the time snapshot from user-space using
application such as testptp or any other applications that uses the
PTP_EXTTS_REQUEST ioctl request.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We add the support of XDP ZC TX submission and cleaning into
stmmac_tx_clean(). The function is made to clean as many TX complete
frames as possible, i.e. limit by priv->dma_tx_size instead of NAPI
budget. For TX ring that is associated with XSK pool, the function
stmmac_xdp_xmit_zc() is introduced to TX frame buffers from XSK pool by
using xsk_tx_peek_desc(). To make stmmac_tx_clean() support the cleaning
of XSK TX frames, STMMAC_TXBUF_T_XSK_TX TX buffer type is introduced.
As stmmac_tx_clean() uses the return value to cue whether NAPI function
should continue to poll, we augment the caller of stmmac_tx_clean() to
pass NAPI budget instead of priv->dma_tx_size through 'budget' input and
made stmmac_tx_clean() to always clean up-to the TX ring size instead.
This allows us to use the return boolean status of stmmac_xdp_xmit_zc()
to decide if XSK TX work is done or not: If true, set 'xmits' to return
'budget - 1' so that NAPI poll may exit. Else, set 'xmits' to return
'budget' to make NAPI poll continue to poll since XSK TX work is not
done. Finally, at the end of stmmac_tx_clean(), the function now take
a maximum value between 'count' and 'xmits' so that status from both
TX cleaning and XSK TX (only for XDP ZC) is considered.
This patch adds a new NAPI poll called stmmac_napi_poll_rxtx() that is
meant to be enabled/disabled for RX and TX ring that are bound to XSK
pool. This NAPI poll function starts with cleaning TX ring, then submits
XSK TX frames to TX ring before proceed to perform RX operations, i.e.
, receiving RX frames and replenishing RX ring with RX free buffers
obtained from XSK pool. Therefore, during XSK RX and TX setup, the driver
enables stmmac_napi_poll_rxtx() for RX and TX operations, then during
XSK RX and TX pool tear-down, the driver reenables the exisiting
independent NAPI poll functions accordingly: stmmac_napi_poll_rx() and
stmmac_napi_poll_tx().
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for receiving packet via AF_XDP zero-copy
mechanism.
XDP ZC uses 1:1 mapping of XDP buffer to receive packet, therefore the
use of split header is not used currently. The 'xdp_buff' is declared as
union together with a struct that contains 'page', 'addr' and
'page_offset' that are associated with primary buffer.
RX buffers are now allocated either via page_pool or xsk pool. For RX
buffers from xsk_pool they are allocated and deallocated using below
functions:
* stmmac_alloc_rx_buffers_zc(struct stmmac_priv *priv, u32 queue)
* dma_free_rx_xskbufs(struct stmmac_priv *priv, u32 queue)
With above functions now available, we then extend the following driver
functions to support XDP ZC:
* stmmac_reinit_rx_buffers()
* __init_dma_rx_desc_rings()
* init_dma_rx_desc_rings()
* __free_dma_rx_desc_resources()
Note: stmmac_alloc_rx_buffers_zc() may return -ENOMEM due to RX XDP
buffer pool is not allocated (e.g. samples/bpf/xdpsock TX-only). But,
it is still ok to let TX XDP ZC to continue, therefore, the -ENOMEM
is silently ignored to let the driver succcessfully transition to XDP
ZC mode for the said RX and TX queue.
As XDP ZC buffer size is different, the DMA buffer size is required
to be reprogrammed accordingly for RX DMA/Queue that is populated with
XDP buffer from XSK pool.
Next, to add or remove per-queue XSK pool, stmmac_xdp_setup_pool()
will call stmmac_xdp_enable_pool() or stmmac_xdp_disable_pool()
that in-turn coordinates the tearing down and setting up RX ring via
RX buffers and descriptors removal and reallocation through
stmmac_disable_rx_queue() and stmmac_enable_rx_queue(). In addition,
stmmac_xsk_wakeup() is added to initiate XDP RX buffer replenishing
by signalling user application to add available XDP frames back to
FILL queue.
For RX processing using XDP zero-copy buffer, stmmac_rx_zc() is
introduced which is implemented with the assumption that RX split
header is disabled. For XDP verdict is XDP_PASS, the XDP buffer is
copied into a sk_buff allocated through stmmac_construct_skb_zc()
and sent to Linux network GRO inside stmmac_dispatch_skb_zc(). Free RX
buffers are then replenished using stmmac_rx_refill_zc()
v2: introduce __stmmac_disable_all_queues() to contain the original code
that does napi_disable() and then make stmmac_setup_tc_block_cb()
to use it. Move synchronize_rcu() into stmmac_disable_all_queues()
that eventually calls __stmmac_disable_all_queues(). Then,
make both stmmac_release() and stmmac_suspend() to use
stmmac_disable_all_queues(). Thanks David Miller for spotting the
synchronize_rcu() issue in v1 patch.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare stmmac_xdp_run_prog() for AF_XDP zero-copy support which will be
added by upcoming patches by splitting out the XDP verdict processing
into __stmmac_xdp_run_prog() and it callable for XDP ZC path which does
not need to verify bpf_prog is not NULL.
The stmmac_xdp_run_prog() is used for regular XDP Rx path which requires
bpf_prog to be verified.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Below functions are made to be per-queue in preparation of XDP ZC:
__init_dma_rx_desc_rings(struct stmmac_priv *priv, u32 queue, gfp_t flags)
__init_dma_tx_desc_rings(struct stmmac_priv *priv, u32 queue)
The original functions below are stay maintained for all queue usage:
init_dma_rx_desc_rings(struct net_device *dev, gfp_t flags)
init_dma_tx_desc_rings(struct net_device *dev)
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The per-queue RX buffer allocation in stmmac_reinit_rx_buffers() can be
made to use stmmac_alloc_rx_buffers() by merging the page_pool alloc
checks for "buf->page" and "buf->sec_page" in stmmac_init_rx_buffers().
This is in preparation for XSK pool allocation later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rearrange RX buffer page_pool recycling logics into dma_recycle_rx_skbufs,
so that we prepare stmmac_reinit_rx_buffers() for XSK pool expansion.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch restructures the per RX queue buffer allocation from page_pool
to stmmac_alloc_rx_buffers().
We also rearrange dma_free_rx_skbufs() so that it can be used in
init_dma_rx_desc_rings() during freeing of RX buffer in the event of
page_pool allocation failure to replace the more efficient method earlier.
The replacement is needed to make the RX buffer alloc and free method
scalable to XDP ZC xsk_pool alloc and free later.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EHL PSE SGMII mode requires to ungate the SERDES PHY rx clk for power up
sequence and vice versa.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PCI device IDs are defined with a prefix PCI_DEVICE_ID.
There is no need to repeat the ID part at the end of each definition.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support of XDP_REDIRECT to another remote cpu for
further action. It also implements ndo_xdp_xmit ops, enabling the driver
to transmit packets forwarded to it by XDP program running on another
interface.
This patch has been tested using "xdp_redirect_cpu" for XDP_REDIRECT
+ drop testing. It also been tested with "xdp_redirect" sample app
which can be used to exercise ndo_xdp_xmit ops. The burst traffics are
generated using pktgen_sample03_burst_single_flow.sh in samples/pktgen
directory.
v4: Move xdp_do_flush() processing into stmmac_finalize_xdp_rx() and
combined the XDP verdict of XDP TX and REDIRECT together.
v3: Added 'nq->trans_start = jiffies' to avoid TX time-out as we are
sharing TX queue between slow path and XDP. Thanks to Jakub Kicinski
for point out.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for XDP_TX action which enables XDP program to
transmit back received frames.
This patch has been tested with the "xdp2" app located in samples/bpf
dir. The DUT receives burst traffic packet generated using pktgen script
'pktgen_sample03_burst_single_flow.sh'.
v4: Moved stmmac_tx_timer_arm() to be done once at the end of NAPI RX.
Fixed stmmac_xdp_xmit_back() to return STMMAC_XDP_CONSUMED if
XDP buffer to frame conversion fails. Thanks to Jakub's input.
v3: Added 'nq->trans_start = jiffies' to avoid TX time-out as we are
sharing TX queue between slow path and XDP. Thanks to Jakub Kicinski
for pointing out.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the initial XDP support to stmmac driver. It supports
XDP_PASS, XDP_DROP and XDP_ABORTED actions. Upcoming patches will add
support for XDP_TX and XDP_REDIRECT.
To support XDP headroom, this patch adds page_offset into RX buffer and
change the dma_sync_single_for_device|cpu(). The DMA address used for
RX operation are changed to take into page_offset too. As page_pool
can handle dma_sync_single_for_device() on behalf of driver with
PP_FLAG_DMA_SYNC_DEV flag, we skip doing that in stmmac driver.
Current stmmac driver supports split header support (SPH) in RX but
the flexibility of splitting header and payload at different position
makes it very complex to be supported for XDP processing. In addition,
jumbo frame is not supported in XDP to keep the initial codes simple.
This patch has been tested with the sample app "xdp1" located in
samples/bpf directory for both SKB and Native (XDP) mode. The burst
traffic generated using pktgen_sample03_burst_single_flow.sh in
samples/pktgen directory.
Changes in v3:
- factor in xdp header and tail adjustment done by XDP program.
Thanks to Jakub Kicinski for pointing out the gap in v2.
Changes in v2:
- fix for "warning: variable 'len' set but not used" reported by lkp.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch organizes TX tail pointer update into a new function called
stmmac_flush_tx_descriptors() so that we can reuse it in stmmac_xmit(),
stmmac_tso_xmit() and up-coming XDP implementation.
Changes to v2:
- Fix for warning: unused variable ‘desc_size’
https://patchwork.hopto.org/static/nipa/457321/12170149/build_32bit/stderr
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SPH functionality splits header and payload according to split mode and
offsef fields (SPLM and SPLOFST). It is beneficials for Linux network
stack RX processing however it adds a lot of complexity in XDP
processing.
So, this patch makes the split-header (SPH) capability of the controller
is stored in "priv->sph_cap" and the enabling/disabling of SPH is decided
by "priv->sph".
This is to prepare initial XDP enabling for stmmac to disable the use of
SPH whenever XDP is enabled.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain platform likes Intel mGBE has independent hardware IRQ resources
for TX and RX DMA operation. In preparation to support XDP TX, we add IRQ
affinity hint to group both RX and TX queue of the same queue ID to the
same CPU.
Changes in v2:
- IRQ affinity hint need to set to null before IRQ is released.
Thanks to issue reported by Song, Yoong Siang.
Reported-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit d2a029bde37b ("stmmac: pci: add MSI support for Intel Quark
X1000") introduced a pci_enable_msi() call in stmmac_pci.c.
With the commit 58da0cfa6cf1 ("net: stmmac: create dwmac-intel.c to
contain all Intel platform"), Intel Quark platform related codes
have been moved to the newly created driver.
Removing this unnecessary pci_enable_msi() call as there are no other
devices that uses stmmac-pci and need MSI to be enabled.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update dwmac-intel to use managed function, i.e. pcim_enable_device().
This will allow devres framework to call resource free function for us.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Turn on the MEEAO field of MTL_ECC_Control_Register by default.
As the MTL ECC Error Address Status Over-ride(MEEAO) is set by default,
the following error address fields will hold the last valid address
where the error is detected.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct stmmac_safety_stats is declared twice. One has been
declared at 29th line. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross time-stamping mechanism used in certain instance of Intel mGbE
may run at different clock frequency in comparison to the clock
frequency used by processor, so we introduce cross T/S frequency
adjustment to ensure TSC calculation is correct when processor got the
cross time-stamps.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
