| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit df1ec1b9d0df57e96011f175418dc95b1af46821.
It turns out that memory allocated via dma_alloc_coherent is always
aligned to the size of the buffer, so there's no way the RRD and RFD
can ever be in separate 32-bit regions.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the error messages that are printed by the interrupt handlers
are poorly written. For example, many don't include a device prefix,
so there's no indication that they are EMAC errors.
Also use rate limiting for all messages that could be printed from
interrupt context.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EMAC has a restriction that the upper 32 bits of the base addresses
for the RFD and RRD rings must be the same. The ensure that restriction,
we allocate twice the space for the RRD and locate it at an appropriate
address.
We also re-arrange the allocations so that invalid addresses are even
less likely.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EMAC is capable of multiple TX and RX rings, but the driver only
supports one ring for each. One function had some left-over unused
code that supports multiple rings, but all it did was make the code
harder to read.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 64/32-bit DMA mask hackery in the EMAC driver is not actually necessary,
and is technically not accurate. The EMAC hardware is limted to a 45-bit
DMA address. Although no EMAC-enabled system can have that much DDR,
an IOMMU could possible provide a larger address. Rather than play games
with the DMA mappings, the driver should provide a correct value and
trust the DMA/IOMMU layers to do the right thing.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function emac_isr is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warnings:
symbol 'emac_isr' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mapping the RX DMA buffers, the driver was accidentally specifying
zero for the buffer length. Under normal circumstances, SWIOTLB does not
need to allocate a bounce buffer, so the address is just mapped without
checking the size field. This is why the error was not detected earlier.
Fixes: b9b17debc69d ("net: emac: emac gigabit ethernet controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EMAC has the option of sending only a single pause frame when
flow control is enabled and the RX queue is full. Although sending
only one pause frame has little value, this would allow admins to
enable automatic flow control without having to worry about the EMAC
flooding nearby switches with pause frames if the kernel hangs.
The option is enabled by using the single-pause-mode private flag.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the interface is not up, then don't try to close it during a
shutdown. This avoids possible double free of the IRQ, which
can happen during a shutdown.
Fixes: 03eb3eb4d4d5 ("net: qcom/emac: add shutdown function")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On emulation systems, the EMAC's internal PHY ("SGMII") is not present,
but is not needed for network functionality. So just display a warning
message and ignore the SGMII.
Tested-by: Philip Elcan <pelcan@codeaurora.org>
Tested-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On ACPI systems, the driver depends on firmware pre-initializing the
EMAC because we don't have access to the clocks, and the EMAC has specific
clock programming requirements. Therefore, we don't want to reset the
EMAC while we are completing the initialization.
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The shutdown function halts all DMA and interrupts, so that all
operations are discontinued when the system shuts down, e.g. via
kexec or a forced reboot.
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use software polling (PHY_POLL) to check for link state changes instead
of relying on the EMAC's hardware polling feature. Some PHY drivers
are unable to get a functioning link because the HW polling is not
robust enough.
The EMAC is able to poll the PHY on the MDIO bus looking for link state
changes (via the Link Status bit in the Status Register at address 0x1).
When the link state changes, the EMAC triggers an interrupt and tells the
driver what the new state is. The feature eliminates the need for
software to poll the MDIO bus.
Unfortunately, this feature is incompatible with phylib, because it
ignores everything that the PHY core and PHY drivers are trying to do.
In particular:
1. It assumes a compatible register set, so PHYs with different registers
may not work.
2. It doesn't allow for hardware errata that have work-arounds implemented
in the PHY driver.
3. It doesn't support multiple register pages. If the PHY core switches
the register set to another page, the EMAC won't know the page has
changed and will still attempt to read the same PHY register.
4. It only checks the copper side of the link, not the SGMII side. Some
PHY drivers (e.g. at803x) may also check the SGMII side, and
report the link as not ready during autonegotiation if the SGMII link
is still down. Phylib then waits for another interrupt to query
the PHY again, but the EMAC won't send another interrupt because it
thinks the link is up.
Cc: stable@vger.kernel.org # 4.11.x
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).
That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust the impedance values of the RX and TX lanes in the SGMII block
so that they are closer to optimal values.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We had intended to say "sizeof(u32)" but the "u" is missing.
Fortunately, sizeof(32) is also 4, so the original code still works.
Fixes: c4e7beea2192 ("net: qcom/emac: add ethtool support for reading hardware registers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the set_ringparam method, which allows the user to specify
the size of the TX and RX descriptor rings. The values are constrained
to the limits of the hardware.
Since the driver does not use separate queues for mini or jumbo frames,
attempts to set those values are rejected.
If the interface is already running when the setting is changed, then
the interface is reset.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the get_regs_len and get_regs ethtool methods. The driver
returns the values of selected hardware registers.
The make the register offsets known to emac_ethtool, the the register
offset macros are all combined into one header file. They were
inexplicably and arbitrarily split between two files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/qualcomm/emac/emac-ethtool.c:155:49-50: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To support setting the pause parameters, the driver can no longer just
mirror the PHY. The set_pauseparam feature allows the driver to
force the setting in the MAC, regardless of how the PHY is configured.
This means that we now need to maintain an internal state for pause
frame support, and so get_pauseparam also needs to be updated.
If the interface is already running when the setting is changed, then
the interface is reset.
Note that if the MAC is configured to enable RX pause frame support
(i.e. it transmits pause frames to throttle the other end), but the
PHY is configured to block those frames, then the feature will not work.
Also some buffer size initialization code into emac_init_adapter(),
so that it lives with similar code, including the initializtion of
pause frame support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SGMII (internal PHY) can report decode errors via an interrupt. It
can also report autonegotiation status changes, but we don't need to track
those. The SGMII can recover automatically from most decode errors, so
we only reset the interface if we get multiple consecutive errors.
It's possible for bogus decode errors to be reported while the link is
being brought up. The interrupt is registered when the interface is
opened, and it's enabled after the link is up.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EMAC driver does not support wake-on-lan, but there is still
code left-over that partially enables it. Remove that code and a few
macros that support it.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
emac_mac_start() uses information from the external PHY to program
the MAC, so it makes no sense to call it before the link is up.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Regardless of how the external PHY is configured, the internal PHY
(the "SGMII" block) is capable of configuring the SGMII link automatically.
When the external PHY link comes up, regardless of how it is configured,
the SGMII link is configured automatically.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY driver is attached only when the driver calls
phy_connect_direct(). Calling phy_attached_print() to display
information about the PHY driver prior to that point is meaningless.
The interface can be brought down, a new PHY driver can be loaded,
and the interface then brought back up. This is the correct time
to display information about the attached driver.
Since phy_attached_print() also prints information about the
interrupt, that needs to be set as well.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During reset, functions emac_mac_down() and emac_mac_up() are called,
so we don't want to free and claim the IRQ unnecessarily. Move those
operations to open/close.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EMAC has an internal PHY that is often called the "SGMII". This
SGMII is also connected to an external PHY, which is managed by phylib.
These dual PHYs often cause confusion. In this case, the data structure
for managing the SGMII was mis-named and located in the wrong header file.
Structure emac_phy is renamed to emac_sgmii to clearly indicate it applies
to the internal PHY only. It also also moved from emac_phy.h (which
supports the external PHY) to emac_sgmii.h (where it belongs).
To keep the changes minimal, only the structure name is changed, not
the names of any variables of that type.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3e884493448131179a5b7cae1ddca1028ffaecc8.
With commit 529ed1275263 ("net: phy: phy drivers should not set
SUPPORTED_[Asym_]Pause"), phylib now handles automatically enabling
pause frame support in the PHY, and the MAC driver should follow suit.
Since the EMAC driver driver does this, we no longer need to force
pause frames support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738376d ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f49b ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dacec ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Commit 6ffe1c4cd0a7 ("net: qcom/emac: fix of_node and phydev leaks")
fixed the problem with reference leaks on phydev, but the fix is
device-tree specific. When the driver unloads, the reference is
dropped only on DT systems.
Instead, it's cleaner if up grab an reference on ACPI systems.
When the driver unloads, we can drop the reference without having
to check whether we're on a DT system.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for some ethtool methods: get/set link settings, get/set
message level, get statistics, get link status, get ring params, get
pause params, and restart autonegotiation.
The code to collect the hardware statistics is moved into its own
function so that it can be used by "get statistics" method.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On ACPI systems, clocks are not available to drivers directly. They are
handled exclusively by ACPI and/or firmware, so there is no clock driver.
Calls to clk_get() always fail, so we should not even attempt to claim
any clocks on ACPI systems.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QDF2432 and the QDF2400 have slightly different internal PHYs,
so there are some programming differences. Some of the registers in
the QDF2400 have moved, and some registers require different values
during initialization.
Because of the differences, and because HIDs are a scare resource,
the ACPI tables specify the hardware version in an _HRV property.
Version 1 is the QDF2432, and version 2 is the QDF2400. Any future
SOC that has the same internal PHY but different programming
requirements will be assigned the next available version number.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal PHY of the EMAC differs on each SOC, and the list will
only continue to grow. By separating the code into individual files,
we can add support for more SOCs more cleanly.
Note: The internal PHY is also sometimes called the SGMII device.
We also stop referring to the various PHY variations by version number,
so no more "v2", "v3", etc. Instead, the devices are named after the
SOC they are, which is in sync with the device tree property names.
Future patches will probably rearrange more code among the files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by of_phy_find_device() during
probe on probe errors and on driver unbind.
Also drop the of_node reference taken by of_parse_phandle() in the same
path.
Fixes: b9b17debc69d ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of bug fixes in 'net' overlapping other changes in
'net-next-.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the PHY has been configured to allow pause frames, then the MAC
should be configured to generate and/or accept those frames.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pause frames are used to enable flow control. A MAC can send and
receive pause frames in order to throttle traffic. However, the PHY
must be configured to allow those frames to pass through.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The documentation says that SGMII_LN_UCDR_SO_GAIN_MODE0 should be
set to 0, not 6, on the Qualcomm Technologies QDF2432.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/ethernet/qualcomm/emac/qcom-emac.ko | grep alias
alias: platform:qcom-emac
After this patch:
$ modinfo drivers/net/ethernet/qualcomm/emac/qcom-emac.ko | grep alias
alias: platform:qcom-emac
alias: of:N*T*Cqcom,fsm9900-emacC*
alias: of:N*T*Cqcom,fsm9900-emac
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a race condition that can occur if EMAC interrupts are
enabled when phy_disconnect() is called. phy_disconnect() sets
adjust_link to NULL. When an interrupt occurs, the ISR might
call phy_mac_interrupt(), which wakes up the workqueue function
phy_state_machine(). This function might reference adjust_link,
thereby causing a null pointer exception.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of error, the function ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Also add check for return value of platform_get_resource().
Fixes: 54e19bc74f33 ("net: qcom/emac: do not use devm on internal
phy pdev")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for reading addresses, interrupts, and _DSD properties
from ACPI tables, just like with device tree. The HID for the
EMAC device itself is QCOM8070. The internal PHY is represented
by a child node with a HID of QCOM8071.
The EMAC also has some complex clock initialization requirements
that are not represented by this patch. This will be addressed
in a future patch.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the DT-specific of_get_mac_address() function with
device_get_mac_address, which works on both DT and ACPI platforms. This
change makes it easier to add ACPI support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
