Age | Commit message (Collapse) | Author | Files | Lines |
|
To support sriov on a E-Switch manager, num_vfs are queried
to the firmware whenever E-Switch manager is notified by
esw_functions_changed event.
Replace host_params event with esw_functions_changed event that reflects
more appropriate naming.
While at it, also correct num_vfs type from int to u16 as expected by
the function mlx5_esw_query_functions().
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Handle event of power state change in the PCIE slot. When the event
occurs, check if query power state and PCI power fields is supported. If
so, read these fields from MPEIN (management PCIE info) register and
issue a corresponding message.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Support Mellanox BlueField SmartNIC (mlx5-updates-2019-02-15)
Bodong Wang says,
BlueField device is a multi-core ARM processor in a highly integrated
system on chip coupled with the ConnectX interconnect controller.
BlueField device can be presented in one out of two modes:
- SEPARATED_HOST: ARM processors as a separated and orthogonal host
like any other external host in the multi-host virtualization model.
- EMBEDDED_CPU: ARM processors as Embedded CPU (EC) and part of the
external hosts virtualization model.
While existing driver already supports the device on separated_host
mode, this patch series focus on the functionalities of embedded_cpu
mode.
On embedded_cpu mode, BlueField device exposes regular network
controller PCI function in the BlueField host(e.g, x86). However, a
separate PCI function called Embedded CPU Physical Function(ECPF) is
also added to the ARM host side, where standard Linux distributions is
able to run on the ARM cores. Depends on the NV configuration from
firmware, ECPF can be the e-switch manager and firmware pages supplier.
If ECPF is configured as e-switch manager and page supplier, it will
take over the responsibilities from the PF on BlueField host includes:
- Owns, controls and manages all e-switch parts, and takes e-switch
traffic by default. It also should perform ENABLE_HCA for the host
PF just like a PF does for its VFs.
- Provides and manages the ICM host memory required for the HCA to
store various contexts for itself, the PF and VFs belong the
e-switch it manages.
The PF on BlueField host side is still responsible for:
- Control its own permanent MAC.
- PCI and SRIOV configurations and perform ENABLE_HCA for its VFs.
The ECPF can also retrieve information about the external host it
controls, like host identifier, PCI BDF and number of virtual functions.
As these parameters may be changed dynamically, an event will be triggered
to the driver on ECPF side.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Embedded CPU (EC) configurations, the EC driver needs to know when
the number of virtual functions change on the corresponding PF at the
host side. This is required so the EC driver can create or destroy
representor net devices that represent the VFs ports.
Whenever a change in the number of VFs occurs, firmware will generate an
event towards the EC which will trigger a work to complete the rest of
the handling. The specifics of the handling will be introduced in a
downstream patch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Eliminate the following compilation warning:
drivers/net/ethernet/mellanox/mlx5/core/events.c: warning: 'error_str'
may be used uninitialized in this function [-Wuninitialized]: => 238:3
Fixes: c2fb3db22d35 ("net/mlx5: Rework handling of port module events")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Will be used in downstream patch to monitor counter changes
by the HCA and report it to the driver by an event.
The driver will update its counters cached data accordingly.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Support a new hardware module status in port module events:
- module_status=0x4 (Cable plugged, but disabled)
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Support a new hardware error type in port module events:
- error_type=0xc (PCIe system power slot exceeded)
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add explicit HW defined error values. For simplicity, keep counters for all
statuses starting from 0, although currently status=0 is not used.
Additionally, when HW signals an unexpected cable status, it is reported
now rather than ignored. And status counter is now updated on errors.
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Print a debug message for every async FW event forwarded to mlx5
interfaces (mlx5e netdev and mlx5_ib rdma module).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow forwarding of SRQ events to mlx5_core interfaces, e.g. mlx5_ib.
Use mlx5_notifier_register/unregister in srq.c in order to allow seamless
transition of srq.c to infiniband subsystem.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow forwarding QP and WQ events to mlx5_core interfaces, e.g. mlx5_ib
Use mlx5_notifier_register/unregister in qp.c in order to allow seamless
transition of qp.c to infiniband subsystem.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Before the new mlx5 event notification infrastructure and API,
mlx5_core used to process all events before forwarding them to mlx5
interfaces (mlx5e/mlx5_ib) and used to translate the event type enum
to a software defined enum, this is not needed anymore since it is ok
for mlx5e and mlx5_ib to receive FW events as is, at least the few ones
mlx5 core allows.
mlx5e and mlx5_ib already moved to use the new API and they only handle FW
events types, it is now safe to remove all equivalent software defined
events and the logic around them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
FW general event is used by mlx5_ib for RQ delay drop timeout event
handling, in this patch we allow to forward FW general event type to mlx5
notifiers chain so mlx5_ib can handle it and to deprecate the software
version of it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The mlx5_interface->event callback is not used by mlx5e/mlx5_ib anymore.
We totally remove the delayed events logic work around, since with
the dynamic notifier registration API it is not needed anymore, mlx5_ib
can register its notifier and start receiving events exactly at the moment
it is ready to handle them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The idea is to allow mlx5 core interfaces (mlx5e/mlx5_ib) to be able to
receive some allowed FW events as is via the new notifier API.
In this patch we allow forwarding port change event to mlx5 core interfaces
(mlx5e/mlx5_ib) as it was received from FW.
Once mlx5e and mlx5_ib start using this event we can safely remove the
redundant software version of it and its translation logic.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use atomic notifier chain to fire events to mlx5 core driver
consumers (mlx5e/mlx5_ib) and provide mlx5 register/unregister notifier
API.
This API will replace the current mlx5_interface->event callback and all
the logic around it, especially the delayed events logic introduced by
commit 97834eba7c19 ("net/mlx5: Delay events till ib registration ends")
Which is not needed anymore with this new API where the mlx5 interface
can dynamically register/unregister its notifier.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Register a separate handler per event type, rather than listening for all
events and looking for the events to handle in a switch case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move all the generic async events handling into new specific events
handling file events.c to keep eq.c file clean from concrete event logic
handling.
Use new API to register for NOTIFY_ANY to handle generic events and
dispatch allowed events to mlx5_core consumers (mlx5_ib and mlx5e)
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|